From: Nishanth Menon <nm@ti.com>
To: Roger Quadros <rogerq@ti.com>
Cc: <t-kristo@ti.com>, <robh+dt@kernel.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>, <nsekhar@ti.com>,
<kishon@ti.com>
Subject: Re: [PATCH v2 6/6] arm64: dts: ti: k3-j7200-common-proc-board: Add USB support
Date: Tue, 8 Sep 2020 07:36:51 -0500 [thread overview]
Message-ID: <20200908123651.yg54ht2z2esqdg4e@akan> (raw)
In-Reply-To: <20200907145213.30788-7-rogerq@ti.com>
On 17:52-20200907, Roger Quadros wrote:
> Enable USB0 port in high-speed (2.0) mode.
Am I right that this is a choice forced by serdes mux configuration
selection? Might be good to document it (default speed is super-speed).
>
> The board uses lane 3 of SERDES for USB. Set the mux
> accordingly.
>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
> .../dts/ti/k3-j7200-common-proc-board.dts | 22 +++++++++++++++++++
> 1 file changed, 22 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index 0ecaba600704..5ce3fddbd617 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> @@ -42,6 +42,12 @@
> J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
> >;
> };
> +
> + main_usbss0_pins_default: main-usbss0-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
> + >;
> + };
> };
>
> &wkup_uart0 {
> @@ -145,3 +151,19 @@
> idle-states = <SERDES0_LANE0_PCIE1_LANE0>, <SERDES0_LANE1_PCIE1_LANE1>,
> <SERDES0_LANE2_QSGMII_LANE1>, <SERDES0_LANE3_IP4_UNUSED>;
> };
> +
> +&usb_serdes_mux {
> + idle-states = <1>; /* USB0 to SERDES lane 3 */
> +};
> +
> +&usbss0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_usbss0_pins_default>;
> + ti,vbus-divider;
> + ti,usb2-only;
> +};
> +
> +&usb0 {
> + dr_mode = "otg";
> + maximum-speed = "high-speed";
> +};
> --
> Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
> Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
prev parent reply other threads:[~2020-09-08 16:36 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-07 14:52 [PATCH v2 0/6] arm64: dts: ti: Add USB support for J7200 EVM Roger Quadros
2020-09-07 14:52 ` [PATCH v2 1/6] dt-bindings: mux-j7200-wiz: Add lane function defines Roger Quadros
2020-09-08 8:39 ` Roger Quadros
2020-09-07 14:52 ` [PATCH v2 2/6] arm64: dts: ti: k3-j7200-main: Add SERDES lane control mux Roger Quadros
2020-09-08 12:30 ` Nishanth Menon
2020-09-07 14:52 ` [PATCH v2 3/6] arm64: dts: ti: k3-j7200-main.dtsi: Add USB to SERDES lane MUX Roger Quadros
2020-09-07 14:52 ` [PATCH v2 4/6] arm64: dts: ti: k3-j7200-main: Add USB controller Roger Quadros
2020-09-07 14:52 ` [PATCH v2 5/6] arm64: dts: ti: k3-j7200-common-proc-board: Configure the SERDES lane function Roger Quadros
2020-09-07 14:52 ` [PATCH v2 6/6] arm64: dts: ti: k3-j7200-common-proc-board: Add USB support Roger Quadros
2020-09-08 12:36 ` Nishanth Menon [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200908123651.yg54ht2z2esqdg4e@akan \
--to=nm@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nsekhar@ti.com \
--cc=robh+dt@kernel.org \
--cc=rogerq@ti.com \
--cc=t-kristo@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).