From: Neil Armstrong <narmstrong@baylibre.com>
To: khilman@baylibre.com
Cc: linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Neil Armstrong <narmstrong@baylibre.com>
Subject: [PATCH 4/5] arm64: dts: meson-axg: add USB nodes
Date: Wed, 9 Sep 2020 18:04:08 +0200 [thread overview]
Message-ID: <20200909160409.8678-5-narmstrong@baylibre.com> (raw)
In-Reply-To: <20200909160409.8678-1-narmstrong@baylibre.com>
This adds the USB Glue node, with the USB2 & USB3 controllers along the single
USB2 PHY node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 51 ++++++++++++++++++++++
1 file changed, 51 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
index 9ae6db16b8e6..0b68a383b60f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
@@ -171,6 +171,46 @@
#size-cells = <2>;
ranges;
+ usb: usb@ffe09080 {
+ compatible = "amlogic,meson-axg-usb-ctrl";
+ reg = <0x0 0xffe09080 0x0 0x20>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1_DDR_BRIDGE>;
+ clock-names = "usb_ctrl", "ddr";
+ resets = <&reset RESET_USB_OTG>;
+
+ dr_mode = "otg";
+
+ phys = <&usb2_phy1>;
+ phy-names = "usb2-phy1";
+
+ dwc2: usb@ff400000 {
+ compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
+ reg = <0x0 0xff400000 0x0 0x40000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc CLKID_USB1>;
+ clock-names = "otg";
+ phys = <&usb2_phy1>;
+ dr_mode = "peripheral";
+ g-rx-fifo-size = <192>;
+ g-np-tx-fifo-size = <128>;
+ g-tx-fifo-size = <128 128 16 16 16>;
+ };
+
+ dwc3: usb@ff500000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0xff500000 0x0 0x100000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ dr_mode = "host";
+ maximum-speed = "high-speed";
+ snps,dis_u2_susphy_quirk;
+ };
+ };
+
ethmac: ethernet@ff3f0000 {
compatible = "amlogic,meson-axg-dwmac",
"snps,dwmac-3.70a",
@@ -1734,6 +1774,17 @@
clock-names = "core", "clkin0", "clkin1";
resets = <&reset RESET_SD_EMMC_C>;
};
+
+ usb2_phy1: phy@9020 {
+ compatible = "amlogic,meson-gxl-usb2-phy";
+ #phy-cells = <0>;
+ reg = <0x0 0x9020 0x0 0x20>;
+ clocks = <&clkc CLKID_USB>;
+ clock-names = "phy";
+ resets = <&reset RESET_USB_OTG>;
+ reset-names = "phy";
+ status = "okay";
+ };
};
sram: sram@fffc0000 {
--
2.22.0
next prev parent reply other threads:[~2020-09-09 16:52 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-09 16:04 [PATCH 0/5] usb: dwc-meson-g12a: Add support for USB on S400 board Neil Armstrong
2020-09-09 16:04 ` [PATCH 1/5] phy: amlogic: phy-meson-gxl-usb2: keep ID pull-up even in Host mode Neil Armstrong
2020-09-15 19:53 ` Martin Blumenstingl
2020-09-09 16:04 ` [PATCH 2/5] dt-bindings: usb: amlogic,meson-g12a-usb-ctrl: add the Amlogic AXG Families USB Glue Bindings Neil Armstrong
2020-09-15 17:32 ` [PATCH 2/5] dt-bindings: usb: amlogic, meson-g12a-usb-ctrl: " Rob Herring
2020-09-15 19:56 ` [PATCH 2/5] dt-bindings: usb: amlogic,meson-g12a-usb-ctrl: " Martin Blumenstingl
2020-09-09 16:04 ` [PATCH 3/5] usb: dwc-meson-g12a: Add support for USB on AXG SoCs Neil Armstrong
2020-09-15 19:59 ` Martin Blumenstingl
2020-09-16 7:11 ` Neil Armstrong
2020-09-09 16:04 ` Neil Armstrong [this message]
2020-09-15 20:04 ` [PATCH 4/5] arm64: dts: meson-axg: add USB nodes Martin Blumenstingl
2020-09-16 7:10 ` Neil Armstrong
2020-09-09 16:04 ` [PATCH 5/5] arm64: dts: meson-axg-s400: enable USB OTG Neil Armstrong
2020-09-15 20:05 ` Martin Blumenstingl
2020-09-16 7:09 ` Neil Armstrong
2020-09-14 17:57 ` [PATCH 0/5] usb: dwc-meson-g12a: Add support for USB on S400 board Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200909160409.8678-5-narmstrong@baylibre.com \
--to=narmstrong@baylibre.com \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).