From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Douglas Anderson <dianders@chromium.org>
Cc: Mark Brown <broonie@kernel.org>,
Akash Asthana <akashast@codeaurora.org>,
swboyd@chromium.org, Andy Gross <agross@kernel.org>,
linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-spi@vger.kernel.org
Subject: Re: [PATCH 2/3] spi: spi-geni-qcom: Don't program CS_TOGGLE again and again
Date: Sat, 12 Sep 2020 18:01:43 -0500 [thread overview]
Message-ID: <20200912230143.GC3715@yoga> (raw)
In-Reply-To: <20200912140730.2.I33e571179986850b4ec17042e813d0b08fb1b9c1@changeid>
On Sat 12 Sep 16:08 CDT 2020, Douglas Anderson wrote:
> We always toggle the chip select manually in spi-geni-qcom so that we
> can properly implement the Linux API. There's no reason to program
> this to the hardware on every transfer. Program it once at init and
> be done with it.
>
> This saves some part of a microsecond of overhead on each transfer.
> While not really noticeable on any real world benchmarks, we might as
> well save the time.
>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Regards,
Bjorn
> Signed-off-by: Douglas Anderson <dianders@chromium.org>
> ---
>
> drivers/spi/spi-geni-qcom.c | 12 +++++++-----
> 1 file changed, 7 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c
> index 7f0bf0dec466..92d88bf85a90 100644
> --- a/drivers/spi/spi-geni-qcom.c
> +++ b/drivers/spi/spi-geni-qcom.c
> @@ -290,6 +290,7 @@ static int spi_geni_init(struct spi_geni_master *mas)
> {
> struct geni_se *se = &mas->se;
> unsigned int proto, major, minor, ver;
> + u32 spi_tx_cfg;
>
> pm_runtime_get_sync(mas->dev);
>
> @@ -322,6 +323,11 @@ static int spi_geni_init(struct spi_geni_master *mas)
>
> geni_se_select_mode(se, GENI_SE_FIFO);
>
> + /* We always control CS manually */
> + spi_tx_cfg = readl(se->base + SE_SPI_TRANS_CFG);
> + spi_tx_cfg &= ~CS_TOGGLE;
> + writel(spi_tx_cfg, se->base + SE_SPI_TRANS_CFG);
> +
> pm_runtime_put(mas->dev);
> return 0;
> }
> @@ -331,7 +337,7 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
> u16 mode, struct spi_master *spi)
> {
> u32 m_cmd = 0;
> - u32 spi_tx_cfg, len;
> + u32 len;
> struct geni_se *se = &mas->se;
> int ret;
>
> @@ -350,7 +356,6 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
> spin_lock_irq(&mas->lock);
> spin_unlock_irq(&mas->lock);
>
> - spi_tx_cfg = readl(se->base + SE_SPI_TRANS_CFG);
> if (xfer->bits_per_word != mas->cur_bits_per_word) {
> spi_setup_word_len(mas, mode, xfer->bits_per_word);
> mas->cur_bits_per_word = xfer->bits_per_word;
> @@ -364,8 +369,6 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
> mas->tx_rem_bytes = 0;
> mas->rx_rem_bytes = 0;
>
> - spi_tx_cfg &= ~CS_TOGGLE;
> -
> if (!(mas->cur_bits_per_word % MIN_WORD_LEN))
> len = xfer->len * BITS_PER_BYTE / mas->cur_bits_per_word;
> else
> @@ -384,7 +387,6 @@ static void setup_fifo_xfer(struct spi_transfer *xfer,
> writel(len, se->base + SE_SPI_RX_TRANS_LEN);
> mas->rx_rem_bytes = xfer->len;
> }
> - writel(spi_tx_cfg, se->base + SE_SPI_TRANS_CFG);
>
> /*
> * Lock around right before we start the transfer since our
> --
> 2.28.0.618.gf4bc123cb7-goog
>
next prev parent reply other threads:[~2020-09-12 23:01 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-12 21:07 [PATCH 1/3] spi: spi-geni-qcom: Use the FIFO even more Douglas Anderson
2020-09-12 21:08 ` [PATCH 2/3] spi: spi-geni-qcom: Don't program CS_TOGGLE again and again Douglas Anderson
2020-09-12 23:01 ` Bjorn Andersson [this message]
2020-09-15 10:40 ` Akash Asthana
2020-09-12 21:08 ` [PATCH 3/3] spi: spi-geni-qcom: Slightly optimize setup of bidirectional xfters Douglas Anderson
2020-09-12 22:54 ` Bjorn Andersson
2020-09-13 1:09 ` Doug Anderson
2020-09-13 20:35 ` Doug Anderson
2020-09-13 3:45 ` kernel test robot
2020-09-13 7:31 ` kernel test robot
2020-09-12 22:53 ` [PATCH 1/3] spi: spi-geni-qcom: Use the FIFO even more Bjorn Andersson
2020-09-13 1:11 ` Doug Anderson
2020-09-13 3:12 ` Bjorn Andersson
2020-09-14 14:52 ` Mark Brown
2020-09-15 7:30 ` Akash Asthana
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200912230143.GC3715@yoga \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=akashast@codeaurora.org \
--cc=broonie@kernel.org \
--cc=dianders@chromium.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=swboyd@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).