From: "Niklas Söderlund" <niklas.soderlund@ragnatech.se>
To: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
Geert Uytterhoeven <geert+renesas@glider.be>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org,
linux-kernel@vger.kernel.org,
Prabhakar <prabhakar.csengg@gmail.com>
Subject: Re: [PATCH v3] media: rcar-vin: Enable YDS bit depending on bus_width and data_shift
Date: Thu, 17 Sep 2020 12:19:42 +0200 [thread overview]
Message-ID: <20200917101942.GA2382958@oden.dyn.berto.se> (raw)
In-Reply-To: <be419827-86b4-8aa2-2c82-2c7e328889c3@xs4all.nl>
Hi Hans,
On 2020-09-17 11:58:16 +0200, Hans Verkuil wrote:
> On 17/09/2020 10:57, Hans Verkuil wrote:
> > Hi Prabhakar,
> >
> > Can you rebase this patch? It no longer applies.
>
> Never mind, my mistake. When I was preparing this patch I also had this patch
> applied: https://patchwork.linuxtv.org/project/linux-media/patch/1595602732-25582-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com/
>
> And that caused the conflict with this YDS patch.
>
> However, I backed out the two renesas-vin-ycbcr-8b-g patches since there were a
> bunch comments for https://patchwork.linuxtv.org/project/linux-media/patch/1595602732-25582-2-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com/
>
> So after dropping those two patches this YDS patch now applies fine and will
> be included in the PR.
Thanks for dropping the renesas-vin-ycbcr-8b-g patches from the PR, they
really should not have been picked up as this patch address the issue in
a nicer way. To ease your workload would you like me to collect VIN
patches and send PR to you for that driver?
>
> Sorry for the confusion,
>
> Hans
>
> >
> > Regards,
> >
> > Hans
> >
> > On 13/09/2020 20:16, Lad Prabhakar wrote:
> >> Enable YDS bit if bus_width and data_shift is set to 8 in parallel mode
> >> for MEDIA_BUS_FMT_UYVY8_2X8 format.
> >>
> >> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> >> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
> >> ---
> >> Changes for v3:
> >> * Dropped BIT macro
> >> * Introduced struct v4l2_fwnode_bus_parallel
> >>
> >> Changes for v2:
> >> * Dropped DT binding documentation patch
> >> * Select the data pins depending on bus-width and data-shift
> >>
> >> v1 -
> >> https://patchwork.kernel.org/project/linux-renesas-soc/list/?series=323799
> >> ---
> >> drivers/media/platform/rcar-vin/rcar-core.c | 9 ++++-----
> >> drivers/media/platform/rcar-vin/rcar-dma.c | 17 ++++++++++++++---
> >> drivers/media/platform/rcar-vin/rcar-vin.h | 5 +++--
> >> 3 files changed, 21 insertions(+), 10 deletions(-)
> >>
> >> diff --git a/drivers/media/platform/rcar-vin/rcar-core.c b/drivers/media/platform/rcar-vin/rcar-core.c
> >> index 7440c8965d27..1149ab76cf5c 100644
> >> --- a/drivers/media/platform/rcar-vin/rcar-core.c
> >> +++ b/drivers/media/platform/rcar-vin/rcar-core.c
> >> @@ -626,12 +626,11 @@ static int rvin_parallel_parse_v4l2(struct device *dev,
> >>
> >> switch (vin->parallel->mbus_type) {
> >> case V4L2_MBUS_PARALLEL:
> >> - vin_dbg(vin, "Found PARALLEL media bus\n");
> >> - vin->parallel->mbus_flags = vep->bus.parallel.flags;
> >> - break;
> >> case V4L2_MBUS_BT656:
> >> - vin_dbg(vin, "Found BT656 media bus\n");
> >> - vin->parallel->mbus_flags = 0;
> >> + vin_dbg(vin, "Found %s media bus\n",
> >> + vin->parallel->mbus_type == V4L2_MBUS_PARALLEL ?
> >> + "PARALLEL" : "BT656");
> >> + vin->parallel->bus = vep->bus.parallel;
> >> break;
> >> default:
> >> vin_err(vin, "Unknown media bus type\n");
> >> diff --git a/drivers/media/platform/rcar-vin/rcar-dma.c b/drivers/media/platform/rcar-vin/rcar-dma.c
> >> index a5dbb90c5210..d067439b0b0d 100644
> >> --- a/drivers/media/platform/rcar-vin/rcar-dma.c
> >> +++ b/drivers/media/platform/rcar-vin/rcar-dma.c
> >> @@ -125,6 +125,7 @@
> >> #define VNDMR2_VPS (1 << 30)
> >> #define VNDMR2_HPS (1 << 29)
> >> #define VNDMR2_CES (1 << 28)
> >> +#define VNDMR2_YDS (1 << 22)
> >> #define VNDMR2_FTEV (1 << 17)
> >> #define VNDMR2_VLV(n) ((n & 0xf) << 12)
> >>
> >> @@ -698,16 +699,26 @@ static int rvin_setup(struct rvin_dev *vin)
> >>
> >> if (!vin->is_csi) {
> >> /* Hsync Signal Polarity Select */
> >> - if (!(vin->parallel->mbus_flags & V4L2_MBUS_HSYNC_ACTIVE_LOW))
> >> + if (!(vin->parallel->bus.flags & V4L2_MBUS_HSYNC_ACTIVE_LOW))
> >> dmr2 |= VNDMR2_HPS;
> >>
> >> /* Vsync Signal Polarity Select */
> >> - if (!(vin->parallel->mbus_flags & V4L2_MBUS_VSYNC_ACTIVE_LOW))
> >> + if (!(vin->parallel->bus.flags & V4L2_MBUS_VSYNC_ACTIVE_LOW))
> >> dmr2 |= VNDMR2_VPS;
> >>
> >> /* Data Enable Polarity Select */
> >> - if (vin->parallel->mbus_flags & V4L2_MBUS_DATA_ENABLE_LOW)
> >> + if (vin->parallel->bus.flags & V4L2_MBUS_DATA_ENABLE_LOW)
> >> dmr2 |= VNDMR2_CES;
> >> +
> >> + switch (vin->mbus_code) {
> >> + case MEDIA_BUS_FMT_UYVY8_2X8:
> >> + if (vin->parallel->bus.bus_width == 8 &&
> >> + vin->parallel->bus.data_shift == 8)
> >> + dmr2 |= VNDMR2_YDS;
> >> + break;
> >> + default:
> >> + break;
> >> + }
> >> }
> >>
> >> /*
> >> diff --git a/drivers/media/platform/rcar-vin/rcar-vin.h b/drivers/media/platform/rcar-vin/rcar-vin.h
> >> index c19d077ce1cb..8396e0e45478 100644
> >> --- a/drivers/media/platform/rcar-vin/rcar-vin.h
> >> +++ b/drivers/media/platform/rcar-vin/rcar-vin.h
> >> @@ -19,6 +19,7 @@
> >> #include <media/v4l2-ctrls.h>
> >> #include <media/v4l2-dev.h>
> >> #include <media/v4l2-device.h>
> >> +#include <media/v4l2-fwnode.h>
> >> #include <media/videobuf2-v4l2.h>
> >>
> >> /* Number of HW buffers */
> >> @@ -92,7 +93,7 @@ struct rvin_video_format {
> >> * @asd: sub-device descriptor for async framework
> >> * @subdev: subdevice matched using async framework
> >> * @mbus_type: media bus type
> >> - * @mbus_flags: media bus configuration flags
> >> + * @bus: media bus parallel configuration
> >> * @source_pad: source pad of remote subdevice
> >> * @sink_pad: sink pad of remote subdevice
> >> *
> >> @@ -102,7 +103,7 @@ struct rvin_parallel_entity {
> >> struct v4l2_subdev *subdev;
> >>
> >> enum v4l2_mbus_type mbus_type;
> >> - unsigned int mbus_flags;
> >> + struct v4l2_fwnode_bus_parallel bus;
> >>
> >> unsigned int source_pad;
> >> unsigned int sink_pad;
> >>
> >
>
--
Regards,
Niklas Söderlund
next prev parent reply other threads:[~2020-09-17 10:21 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-13 18:16 [PATCH v3] media: rcar-vin: Enable YDS bit depending on bus_width and data_shift Lad Prabhakar
2020-09-14 23:45 ` Laurent Pinchart
2020-09-15 0:01 ` Niklas Söderlund
2020-09-15 0:02 ` Laurent Pinchart
2020-09-17 8:57 ` Hans Verkuil
2020-09-17 9:58 ` Hans Verkuil
2020-09-17 10:19 ` Niklas Söderlund [this message]
2020-09-17 10:42 ` Hans Verkuil
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200917101942.GA2382958@oden.dyn.berto.se \
--to=niklas.soderlund@ragnatech.se \
--cc=geert+renesas@glider.be \
--cc=hverkuil@xs4all.nl \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=prabhakar.csengg@gmail.com \
--cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).