linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Krzysztof Kozlowski <krzk@kernel.org>
To: Rob Herring <robh+dt@kernel.org>, Shawn Guo <shawnguo@kernel.org>,
	Sascha Hauer <s.hauer@pengutronix.de>,
	Pengutronix Kernel Team <kernel@pengutronix.de>,
	Fabio Estevam <festevam@gmail.com>,
	NXP Linux Team <linux-imx@nxp.com>,
	Krzysztof Kozlowski <krzk@kernel.org>,
	Adam Ford <aford173@gmail.com>,
	Daniel Baluta <daniel.baluta@nxp.com>,
	Anson Huang <Anson.Huang@nxp.com>, Jacky Bai <ping.bai@nxp.com>,
	Robin Gong <yibin.gong@nxp.com>, Peter Chen <peter.chen@nxp.com>,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org
Cc: Tim Harvey <tharvey@gateworks.com>
Subject: [PATCH v2 3/4] arm64: dts: imx8mn: correct interrupt flags
Date: Thu, 17 Sep 2020 20:54:48 +0200	[thread overview]
Message-ID: <20200917185449.5687-3-krzk@kernel.org> (raw)
In-Reply-To: <20200917185449.5687-1-krzk@kernel.org>

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW

For level low interrupts, enable also internal pull up.  It is
required at least on imx8mm-evk, according to schematics.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Not tested on HW.

Changes since v1:
1. Correct title.
2. Enable pull ups.
---
 arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 4 ++--
 arch/arm64/boot/dts/freescale/imx8mn-evk.dts      | 3 ++-
 arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi     | 2 +-
 3 files changed, 5 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
index 8f7155716c84..b0e8cb256a78 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -55,7 +55,7 @@
 		reg = <0x4b>;
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		rohm,reset-snvs-powered;
 
 		regulators {
@@ -157,7 +157,7 @@
 &iomuxc {
 	pinctrl_pmic: pmicirqgrp {
 		fsl,pins = <
-			MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x41
+			MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x141
 		>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-evk.dts
index b846526a8d8b..707d8486b4d8 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-evk.dts
@@ -7,6 +7,7 @@
 
 #include "imx8mn.dtsi"
 #include "imx8mn-evk.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "NXP i.MX8MNano EVK board";
@@ -19,7 +20,7 @@
 		reg = <0x25>;
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 
 		regulators {
 			buck1: BUCK1{
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
index 7f4b904e9982..4aa0dbd578df 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
@@ -225,7 +225,7 @@
 
 	pinctrl_pmic: pmicirqgrp {
 		fsl,pins = <
-			MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x41
+			MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x141
 		>;
 	};
 
-- 
2.17.1


  parent reply	other threads:[~2020-09-17 18:55 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-09-17 18:54 [PATCH v2 1/4] ARM: dts: imx6qdl-gw5xxx: correct interrupt flags Krzysztof Kozlowski
2020-09-17 18:54 ` [PATCH v2 2/4] arm64: dts: imx8mm: " Krzysztof Kozlowski
2020-09-17 18:54 ` Krzysztof Kozlowski [this message]
2020-09-17 18:54 ` [PATCH v2 4/4] arm64: dts: imx8mq: " Krzysztof Kozlowski
2020-09-17 21:07 ` [PATCH v2 1/4] ARM: dts: imx6qdl-gw5xxx: " Tim Harvey
2020-09-22  6:40 ` Shawn Guo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200917185449.5687-3-krzk@kernel.org \
    --to=krzk@kernel.org \
    --cc=Anson.Huang@nxp.com \
    --cc=aford173@gmail.com \
    --cc=daniel.baluta@nxp.com \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=kernel@pengutronix.de \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-imx@nxp.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=peter.chen@nxp.com \
    --cc=ping.bai@nxp.com \
    --cc=robh+dt@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=shawnguo@kernel.org \
    --cc=tharvey@gateworks.com \
    --cc=yibin.gong@nxp.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).