[PATCH v6 0/3] Adding support for Microchip/Microsemi serial GPIO controller

[PATCH v6 0/3] Adding support for Microchip/Microsemi serial GPIO controller

[Lars Povlsen]

The series add support for the serial GPIO controller used by
Microchip Sparx5, as well as (MSCC) ocelot/jaguar2 SoCs.

v6 changes:
- Use "bus-frequency" instead of "microchip,sgpio-frequency". Drop
  '$ref'. (Robh)
- Added "ngpios" description, bumped minimum to 32. (Linus)
- Added "#size-cells" description. (Linus)
- Changed "bus-frequency" validation in driver to reflect the YAML
  description.

v5 changes (driver comments from Linus):
- Collect bank data in sgpio_bank struct
- Add is_input boolean to sgpio_bank struct
- Use single-bit bitmasks in sgpio_output_set() and sgpio_output_get()
- Eliminate superfluous struct pinctrl_dev *pctl_dev in bank data
- Fix wrong ngpio consistency check

v4 changes (binding comments from Rob):
- microchip,sgpio-port-ranges changed to uint32-matrix so tuples can
  be represented properly.
- gpio controller node name changed to "gpio@[0-1]"
- whitespace fixes
- DT files updated as per schema changes

v3 changes:
- Renamed all usage of "mchp" abbrevation with "microchip".
- Split the in/output directions into (two) separate banks.
- Eliminated the bindings include file (from above)
- Changed SPDX license to "GPL-2.0-or-later"
- Change -ENOTSUPP to -EOPNOTSUPP
- Minor type/symbol naming changes

v2 changes:
- Adds both in and output modes.
- Use direct adressing of the individual banks (#gpio-cells = <4>),
  also osoleting need for addressing macros in bindings include file.
- Property 'microchip,sgpio-ports' (uint32, bitmask) replaced by
  proper range set (array of [start,end]) 'microchip,sgpio-port-ranges'.
- Fixes whitespace issues in Kconfig file

Lars Povlsen (3):
  dt-bindings: pinctrl: Add bindings for pinctrl-microchip-sgpio driver
  pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi
    Serial GPIO
  arm64: dts: sparx5: Add SGPIO devices

Lars Povlsen (3):
  dt-bindings: pinctrl: Add bindings for pinctrl-microchip-sgpio driver
  pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi
    Serial GPIO
  arm64: dts: sparx5: Add SGPIO devices

 .../pinctrl/microchip,sparx5-sgpio.yaml       | 145 ++++
 MAINTAINERS                                   |   1 +
 arch/arm64/boot/dts/microchip/sparx5.dtsi     |  91 +++
 .../boot/dts/microchip/sparx5_pcb125.dts      |   5 +
 .../dts/microchip/sparx5_pcb134_board.dtsi    | 258 +++++++
 .../dts/microchip/sparx5_pcb135_board.dtsi    |  55 ++
 drivers/pinctrl/Kconfig                       |  18 +
 drivers/pinctrl/Makefile                      |   1 +
 drivers/pinctrl/pinctrl-microchip-sgpio.c     | 667 ++++++++++++++++++
 9 files changed, 1241 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
 create mode 100644 drivers/pinctrl/pinctrl-microchip-sgpio.c

--
2.25.1

[PATCH v6 1/3] dt-bindings: pinctrl: Add bindings for pinctrl-microchip-sgpio driver

[Lars Povlsen]

This adds DT bindings for the Microsemi/Microchip SGPIO controller,
bindings microchip,sparx5-sgpio, mscc,ocelot-sgpio and
mscc,luton-sgpio.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../pinctrl/microchip,sparx5-sgpio.yaml       | 145 ++++++++++++++++++
 1 file changed, 145 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
new file mode 100644
index 000000000000..08325bf77a81
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
@@ -0,0 +1,145 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/microchip,sparx5-sgpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microsemi/Microchip Serial GPIO controller
+
+maintainers:
+  - Lars Povlsen <lars.povlsen@microchip.com>
+
+description: |
+  By using a serial interface, the SIO controller significantly extend
+  the number of available GPIOs with a minimum number of additional
+  pins on the device. The primary purpose of the SIO controllers is to
+  connect control signals from SFP modules and to act as an LED
+  controller.
+
+properties:
+  $nodename:
+    pattern: "^gpio@[0-9a-f]+$"
+
+  compatible:
+    enum:
+      - microchip,sparx5-sgpio
+      - mscc,ocelot-sgpio
+      - mscc,luton-sgpio
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  microchip,sgpio-port-ranges:
+    description: This is a sequence of tuples, defining intervals of
+      enabled ports in the serial input stream. The enabled ports must
+      match the hardware configuration in order for signals to be
+      properly written/read to/from the controller holding
+      registers. Being tuples, then number of arguments must be
+      even. The tuples mast be ordered (low, high) and are
+      inclusive.
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    items:
+      items:
+        - description: |
+            "low" indicates start bit number of range
+          minimum: 0
+          maximum: 31
+        - description: |
+            "high" indicates end bit number of range
+          minimum: 0
+          maximum: 31
+    minItems: 1
+    maxItems: 32
+
+  bus-frequency:
+    description: The sgpio controller frequency (Hz). This dictates
+      the serial bitstream speed, which again affects the latency in
+      getting control signals back and forth between external shift
+      registers. The speed must be no larger than half the system
+      clock, and larger than zero.
+    default: 12500000
+
+patternProperties:
+  "^gpio@[0-1]$":
+    type: object
+    properties:
+      compatible:
+        const: microchip,sparx5-sgpio-bank
+
+      reg:
+        description: |
+          The GPIO bank number. "0" is designates the input pin bank,
+          "1" the output bank.
+        maxItems: 1
+
+      gpio-controller: true
+
+      '#gpio-cells':
+        description: |
+         Specifies the pin (port and bit) and flags. Note that the
+         SGIO pin is defined by *2* numbers, a port number between 0
+         and 31, and a bit index, 0 to 3. The maximum bit number is
+         controlled indirectly by the "ngpios" property: (ngpios/32).
+        const: 3
+
+      ngpios:
+        description: The numbers of GPIO's exposed. This must be a
+          multiple of 32.
+        minimum: 32
+        maximum: 128
+
+    required:
+      - compatible
+      - reg
+      - gpio-controller
+      - '#gpio-cells'
+      - ngpios
+
+    additionalProperties: false
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - microchip,sgpio-port-ranges
+  - "#address-cells"
+  - "#size-cells"
+
+examples:
+  - |
+    sgpio2: gpio@1101059c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      compatible = "microchip,sparx5-sgpio";
+      clocks = <&sys_clk>;
+      pinctrl-0 = <&sgpio2_pins>;
+      pinctrl-names = "default";
+      reg = <0x1101059c 0x100>;
+      microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>;
+      bus-frequency = <25000000>;
+      sgpio_in2: gpio@0 {
+        reg = <0>;
+        compatible = "microchip,sparx5-sgpio-bank";
+        gpio-controller;
+        #gpio-cells = <3>;
+        ngpios = <96>;
+      };
+      sgpio_out2: gpio@1 {
+        compatible = "microchip,sparx5-sgpio-bank";
+        reg = <1>;
+        gpio-controller;
+        #gpio-cells = <3>;
+        ngpios = <96>;
+      };
+    };
--
2.25.1

[PATCH v6 2/3] pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO

[Lars Povlsen]

This adds a pinctrl driver for the Microsemi/Microchip Serial GPIO
(SGPIO) device used in various SoC's.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
---
 MAINTAINERS                               |   1 +
 drivers/pinctrl/Kconfig                   |  18 +
 drivers/pinctrl/Makefile                  |   1 +
 drivers/pinctrl/pinctrl-microchip-sgpio.c | 667 ++++++++++++++++++++++
 4 files changed, 687 insertions(+)
 create mode 100644 drivers/pinctrl/pinctrl-microchip-sgpio.c

diff --git a/MAINTAINERS b/MAINTAINERS
index cc70e3ab428b..a8cc028b84d0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2137,6 +2137,7 @@ M:	Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Supported
 F:	arch/arm64/boot/dts/microchip/
+F:	drivers/pinctrl/pinctrl-microchip-sgpio.c
 N:	sparx5
 
 ARM/MIOA701 MACHINE SUPPORT
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 8828613c4e0e..1b3527d4c3c8 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -404,6 +404,24 @@ config PINCTRL_OCELOT
 	select OF_GPIO
 	select REGMAP_MMIO
 
+config PINCTRL_MICROCHIP_SGPIO
+	bool "Pinctrl driver for Microsemi/Microchip Serial GPIO"
+	depends on OF
+	depends on HAS_IOMEM
+	select GPIOLIB
+	select GENERIC_PINCONF
+	select GENERIC_PINCTRL_GROUPS
+	select GENERIC_PINMUX_FUNCTIONS
+	select OF_GPIO
+	help
+	  Support for the serial GPIO interface used on Microsemi and
+	  Microchip SoC's. By using a serial interface, the SIO
+	  controller significantly extends the number of available
+	  GPIOs with a minimum number of additional pins on the
+	  device. The primary purpose of the SIO controller is to
+	  connect control signals from SFP modules and to act as an
+	  LED controller.
+
 source "drivers/pinctrl/actions/Kconfig"
 source "drivers/pinctrl/aspeed/Kconfig"
 source "drivers/pinctrl/bcm/Kconfig"
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index 1731b2154df9..347b0e015960 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -49,6 +49,7 @@ obj-$(CONFIG_PINCTRL_ZYNQ)	+= pinctrl-zynq.o
 obj-$(CONFIG_PINCTRL_INGENIC)	+= pinctrl-ingenic.o
 obj-$(CONFIG_PINCTRL_RK805)	+= pinctrl-rk805.o
 obj-$(CONFIG_PINCTRL_OCELOT)	+= pinctrl-ocelot.o
+obj-$(CONFIG_PINCTRL_MICROCHIP_SGPIO)	+= pinctrl-microchip-sgpio.o
 obj-$(CONFIG_PINCTRL_EQUILIBRIUM)   += pinctrl-equilibrium.o
 
 obj-y				+= actions/
diff --git a/drivers/pinctrl/pinctrl-microchip-sgpio.c b/drivers/pinctrl/pinctrl-microchip-sgpio.c
new file mode 100644
index 000000000000..64d2905d60b7
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-microchip-sgpio.c
@@ -0,0 +1,667 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Microsemi/Microchip SoCs serial gpio driver
+ *
+ * Author: <lars.povlsen@microchip.com>
+ *
+ * Copyright (c) 2020 Microchip Technology Inc. and its subsidiaries.
+ */
+
+#include <linux/gpio/driver.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/of_device.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/clk.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/platform_device.h>
+
+#include "core.h"
+#include "pinconf.h"
+#include "pinmux.h"
+
+#define SGPIO_BITS_PER_WORD	32
+#define SGPIO_MAX_BITS		4
+
+#define PIN_NAM_SZ	(sizeof("SGPIO_D_pXXbY")+1)
+
+enum {
+	REG_INPUT_DATA,
+	REG_PORT_CONFIG,
+	REG_PORT_ENABLE,
+	REG_SIO_CONFIG,
+	REG_SIO_CLOCK,
+	MAXREG
+};
+
+struct sgpio_properties {
+	u8 regoff[MAXREG];
+	u32 auto_repeat;
+	u32 port_width;
+	u32 clk_freq;
+	u32 bit_source;
+};
+
+#define __shf(x)		(__builtin_ffsll(x) - 1)
+#define __BF_PREP(bf, x)	(bf & ((x) << __shf(bf)))
+#define __BF_GET(bf, x)		(((x & bf) >> __shf(bf)))
+
+#define SGPIO_M_CFG_SIO_AUTO_REPEAT(p)	  ((p)->properties->auto_repeat)
+#define SGPIO_F_CFG_SIO_PORT_WIDTH(p, x)  __BF_PREP((p)->properties->port_width, x)
+#define SGPIO_M_CFG_SIO_PORT_WIDTH(p)	  ((p)->properties->port_width)
+#define SGPIO_F_CLOCK_SIO_CLK_FREQ(p, x)  __BF_PREP((p)->properties->clk_freq, x)
+#define SGPIO_M_CLOCK_SIO_CLK_FREQ(p)     ((p)->properties->clk_freq)
+#define SGPIO_F_PORT_CFG_BIT_SOURCE(p, x) __BF_PREP((p)->properties->bit_source, x)
+#define SGPIO_X_PORT_CFG_BIT_SOURCE(p, x) __BF_GET((p)->properties->bit_source, x)
+
+const struct sgpio_properties properties_luton = {
+	.regoff = { 0x00, 0x09, 0x29, 0x2a, 0x2b },
+	.auto_repeat = BIT(5),
+	.port_width  = GENMASK(3, 2),
+	.clk_freq    = GENMASK(11, 0),
+	.bit_source  = GENMASK(11, 0),
+};
+
+const struct sgpio_properties properties_ocelot = {
+	.regoff = { 0x00, 0x06, 0x26, 0x04, 0x05 },
+	.auto_repeat = BIT(10),
+	.port_width  = GENMASK(8, 7),
+	.clk_freq    = GENMASK(19, 8),
+	.bit_source  = GENMASK(23, 12),
+};
+
+const struct sgpio_properties properties_sparx5 = {
+	.regoff = { 0x00, 0x06, 0x26, 0x04, 0x05 },
+	.auto_repeat = BIT(6),
+	.port_width  = GENMASK(4, 3),
+	.clk_freq    = GENMASK(19, 8),
+	.bit_source  = GENMASK(23, 12),
+};
+
+static const char * const functions[] = { "gpio" };
+
+struct sgpio_bank {
+	struct sgpio_priv *priv;
+	bool is_input;
+	struct gpio_chip gpio;
+	struct pinctrl_desc pctl_desc;
+};
+
+struct sgpio_priv {
+	struct device *dev;
+	struct sgpio_bank in;
+	struct sgpio_bank out;
+	u32 bitcount;
+	u32 ports;
+	u32 clock;
+	u32 __iomem *regs;
+	const struct sgpio_properties *properties;
+};
+
+struct sgpio_port_addr {
+	u8 port;
+	u8 bit;
+};
+
+static inline void sgpio_pin_to_addr(struct sgpio_priv *priv, int pin,
+				     struct sgpio_port_addr *addr)
+{
+	addr->port = pin / priv->bitcount;
+	addr->bit = pin % priv->bitcount;
+}
+
+static inline u32 sgpio_readl(struct sgpio_priv *priv, u32 rno, u32 off)
+{
+	u32 __iomem *reg = &priv->regs[priv->properties->regoff[rno] + off];
+
+	return readl(reg);
+}
+
+static inline void sgpio_writel(struct sgpio_priv *priv,
+				u32 val, u32 rno, u32 off)
+{
+	u32 __iomem *reg = &priv->regs[priv->properties->regoff[rno] + off];
+
+	writel(val, reg);
+}
+
+static inline void sgpio_clrsetbits(struct sgpio_priv *priv,
+				    u32 rno, u32 off, u32 clear, u32 set)
+{
+	u32 __iomem *reg = &priv->regs[priv->properties->regoff[rno] + off];
+	u32 val = readl(reg);
+
+	val &= ~clear;
+	val |= set;
+
+	writel(val, reg);
+}
+
+static void sgpio_output_set(struct sgpio_priv *priv,
+			     struct sgpio_port_addr *addr,
+			     int value)
+{
+	unsigned int bit = 3 * addr->bit;
+
+	sgpio_clrsetbits(priv, REG_PORT_CONFIG, addr->port,
+			 SGPIO_F_PORT_CFG_BIT_SOURCE(priv, BIT(bit)),
+			 SGPIO_F_PORT_CFG_BIT_SOURCE(priv, value << bit));
+}
+
+static int sgpio_output_get(struct sgpio_priv *priv,
+			    struct sgpio_port_addr *addr)
+{
+	u32 portval = sgpio_readl(priv, REG_PORT_CONFIG, addr->port);
+	unsigned int bit = 3 * addr->bit;
+
+	return !!(SGPIO_X_PORT_CFG_BIT_SOURCE(priv, portval) & BIT(bit));
+}
+
+static int sgpio_input_get(struct sgpio_priv *priv,
+			   struct sgpio_port_addr *addr)
+{
+	int ret;
+
+	ret = !!(sgpio_readl(priv, REG_INPUT_DATA, addr->bit) &
+		 BIT(addr->port));
+
+	return ret;
+}
+
+static int sgpio_pinconf_get(struct pinctrl_dev *pctldev,
+			     unsigned int pin, unsigned long *config)
+{
+	struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+	struct sgpio_priv *priv = bank->priv;
+	struct sgpio_port_addr addr;
+	u32 param = pinconf_to_config_param(*config);
+	int val;
+
+	sgpio_pin_to_addr(priv, pin, &addr);
+
+	switch (param) {
+	case PIN_CONFIG_INPUT_ENABLE:
+		val = bank->is_input;
+		break;
+
+	case PIN_CONFIG_OUTPUT_ENABLE:
+		val = !bank->is_input;
+		break;
+
+	case PIN_CONFIG_OUTPUT:
+		if (bank->is_input)
+			return -EINVAL;
+		val = sgpio_output_get(priv, &addr);
+		break;
+
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	*config = pinconf_to_config_packed(param, val);
+
+	return 0;
+}
+
+static int sgpio_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
+			     unsigned long *configs, unsigned int num_configs)
+{
+	struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+	struct sgpio_priv *priv = bank->priv;
+	struct sgpio_port_addr addr;
+	u32 param, arg;
+	int cfg, err = 0;
+
+	sgpio_pin_to_addr(priv, pin, &addr);
+
+	for (cfg = 0; cfg < num_configs; cfg++) {
+		param = pinconf_to_config_param(configs[cfg]);
+		arg = pinconf_to_config_argument(configs[cfg]);
+
+		switch (param) {
+		case PIN_CONFIG_OUTPUT:
+			if (bank->is_input)
+				return -EINVAL;
+			sgpio_output_set(priv, &addr, arg);
+			break;
+
+		default:
+			err = -EOPNOTSUPP;
+		}
+	}
+
+	return err;
+}
+
+static const struct pinconf_ops sgpio_confops = {
+	.is_generic = true,
+	.pin_config_get = sgpio_pinconf_get,
+	.pin_config_set = sgpio_pinconf_set,
+	.pin_config_config_dbg_show = pinconf_generic_dump_config,
+};
+
+static int sgpio_get_functions_count(struct pinctrl_dev *pctldev)
+{
+	return 1;
+}
+
+static const char *sgpio_get_function_name(struct pinctrl_dev *pctldev,
+					   unsigned int function)
+{
+	return functions[0];
+}
+
+static int sgpio_get_function_groups(struct pinctrl_dev *pctldev,
+				     unsigned int function,
+				     const char *const **groups,
+				     unsigned *const num_groups)
+{
+	*groups  = functions;
+	*num_groups = ARRAY_SIZE(functions);
+
+	return 0;
+}
+
+static int sgpio_pinmux_set_mux(struct pinctrl_dev *pctldev,
+				unsigned int selector, unsigned int group)
+{
+	return 0;
+}
+
+static int sgpio_gpio_set_direction(struct pinctrl_dev *pctldev,
+				    struct pinctrl_gpio_range *range,
+				    unsigned int pin, bool input)
+{
+	struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+
+	if (input != bank->is_input) {
+		dev_err(pctldev->dev, "Pin %d direction as %s is not possible\n",
+			pin, input ? "input" : "output");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int sgpio_gpio_request_enable(struct pinctrl_dev *pctldev,
+				     struct pinctrl_gpio_range *range,
+				     unsigned int offset)
+{
+	struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+	struct sgpio_priv *priv = bank->priv;
+	struct sgpio_port_addr addr;
+
+	sgpio_pin_to_addr(priv, offset, &addr);
+
+	if ((priv->ports & BIT(addr.port)) == 0) {
+		dev_warn(priv->dev, "%s: Request port %d for pin %d is not activated\n",
+			 __func__, addr.port, offset);
+	}
+
+	return 0;
+}
+
+static const struct pinmux_ops sgpio_pmx_ops = {
+	.get_functions_count = sgpio_get_functions_count,
+	.get_function_name = sgpio_get_function_name,
+	.get_function_groups = sgpio_get_function_groups,
+	.set_mux = sgpio_pinmux_set_mux,
+	.gpio_set_direction = sgpio_gpio_set_direction,
+	.gpio_request_enable = sgpio_gpio_request_enable,
+};
+
+static int sgpio_pctl_get_groups_count(struct pinctrl_dev *pctldev)
+{
+	struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+
+	return bank->pctl_desc.npins;
+}
+
+static const char *sgpio_pctl_get_group_name(struct pinctrl_dev *pctldev,
+					     unsigned int group)
+{
+	struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+
+	return bank->pctl_desc.pins[group].name;
+}
+
+static int sgpio_pctl_get_group_pins(struct pinctrl_dev *pctldev,
+				     unsigned int group,
+				     const unsigned int **pins,
+				     unsigned int *num_pins)
+{
+	struct sgpio_bank *bank = pinctrl_dev_get_drvdata(pctldev);
+
+	*pins = &bank->pctl_desc.pins[group].number;
+	*num_pins = 1;
+
+	return 0;
+}
+
+static const struct pinctrl_ops sgpio_pctl_ops = {
+	.get_groups_count = sgpio_pctl_get_groups_count,
+	.get_group_name = sgpio_pctl_get_group_name,
+	.get_group_pins = sgpio_pctl_get_group_pins,
+	.dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
+	.dt_free_map = pinconf_generic_dt_free_map,
+};
+
+static int microchip_sgpio_direction_input(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct sgpio_bank *bank = gpiochip_get_data(gc);
+
+	/* Fixed-position function */
+	return bank->is_input ? 0 : -EINVAL;
+}
+
+static int microchip_sgpio_direction_output(struct gpio_chip *gc,
+				       unsigned int gpio, int value)
+{
+	struct sgpio_bank *bank = gpiochip_get_data(gc);
+	struct sgpio_priv *priv = bank->priv;
+	struct sgpio_port_addr addr;
+
+	/* Fixed-position function */
+	if (bank->is_input)
+		return -EINVAL;
+
+	sgpio_pin_to_addr(priv, gpio, &addr);
+
+	sgpio_output_set(priv, &addr, value);
+
+	return 0;
+}
+
+static int microchip_sgpio_get_direction(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct sgpio_bank *bank = gpiochip_get_data(gc);
+
+	return bank->is_input ? GPIO_LINE_DIRECTION_IN : GPIO_LINE_DIRECTION_OUT;
+}
+
+static void microchip_sgpio_set_value(struct gpio_chip *gc,
+				unsigned int gpio, int value)
+{
+	microchip_sgpio_direction_output(gc, gpio, value);
+}
+
+static int microchip_sgpio_get_value(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct sgpio_bank *bank = gpiochip_get_data(gc);
+	struct sgpio_priv *priv = bank->priv;
+	struct sgpio_port_addr addr;
+	int ret;
+
+	sgpio_pin_to_addr(priv, gpio, &addr);
+
+	if (bank->is_input)
+		ret = sgpio_input_get(priv, &addr);
+	else
+		ret = sgpio_output_get(priv, &addr);
+
+	return ret;
+}
+
+static int microchip_sgpio_of_xlate(struct gpio_chip *gc,
+			       const struct of_phandle_args *gpiospec,
+			       u32 *flags)
+{
+	struct sgpio_bank *bank = gpiochip_get_data(gc);
+	struct sgpio_priv *priv = bank->priv;
+	int pin;
+
+	/* Note that the SGIO pin is defined by *2* numbers, a port
+	 * number between 0 and 31, and a bit index, 0 to 3.
+	 */
+	if (gpiospec->args[0] > SGPIO_BITS_PER_WORD ||
+	    gpiospec->args[1] > priv->bitcount)
+		return -EINVAL;
+
+	pin = gpiospec->args[1] + (gpiospec->args[0] * priv->bitcount);
+
+	if (pin > gc->ngpio)
+		return -EINVAL;
+
+	if (flags)
+		*flags = gpiospec->args[2];
+
+	return pin;
+}
+
+static int microchip_sgpio_get_ports(struct sgpio_priv *priv)
+{
+	struct device *dev = priv->dev;
+	struct device_node *np = dev->of_node;
+	int i, ret;
+	u32 range_params[64];
+
+	/* Calculate port mask */
+	ret = of_property_read_variable_u32_array(np,
+						  "microchip,sgpio-port-ranges",
+						  range_params,
+						  2,
+						  ARRAY_SIZE(range_params));
+	if (ret < 0 || ret % 2) {
+		dev_err(dev, "%s port range\n",
+			ret == -EINVAL ? "Missing" : "Invalid");
+		return ret;
+	}
+	for (i = 0; i < ret; i += 2) {
+		int start, end;
+
+		start = range_params[i];
+		end = range_params[i + 1];
+		if (start > end || end >= SGPIO_BITS_PER_WORD) {
+			dev_err(dev, "Ill-formed port-range [%d:%d]\n",
+				start, end);
+		}
+		priv->ports |= GENMASK(end, start);
+	}
+
+	return 0;
+}
+
+static int microchip_sgpio_register_bank(struct device *dev,
+					 struct sgpio_priv *priv,
+					 struct fwnode_handle *fwnode,
+					 int bankno)
+{
+	struct sgpio_bank *bank;
+	struct pinctrl_pin_desc *pins;
+	struct pinctrl_desc *pctl_desc;
+	struct pinctrl_dev *pctldev;
+	struct gpio_chip *gc;
+	bool is_input = (bankno == 0);
+	int ret;
+	u32 ngpios;
+
+	/* Get overall bank struct */
+	bank = is_input ? &priv->in : &priv->out;
+	bank->is_input = is_input;
+	bank->priv = priv;
+
+	if (fwnode_property_read_u32(fwnode, "ngpios", &ngpios)) {
+		dev_info(dev, "failed to get number of gpios for bank%d\n",
+			 bankno);
+		ngpios = 64;
+	}
+
+	priv->bitcount = ngpios / SGPIO_BITS_PER_WORD;
+	if (priv->bitcount > SGPIO_MAX_BITS) {
+		dev_err(dev, "Bit width exceeds maximum (%d)\n",
+			SGPIO_MAX_BITS);
+		return -EINVAL;
+	}
+
+	pctl_desc = &bank->pctl_desc;
+	pctl_desc->name = devm_kasprintf(dev, GFP_KERNEL, "%s-%sput",
+					 dev_name(dev),
+					 is_input ? "in" : "out");
+	pctl_desc->pctlops = &sgpio_pctl_ops;
+	pctl_desc->pmxops = &sgpio_pmx_ops;
+	pctl_desc->confops = &sgpio_confops;
+	pctl_desc->owner = THIS_MODULE;
+
+	pins = devm_kzalloc(dev, sizeof(*pins)*ngpios, GFP_KERNEL);
+	if (pins) {
+		int i;
+		char *p, *names;
+
+		names = devm_kzalloc(dev, PIN_NAM_SZ*ngpios, GFP_KERNEL);
+
+		if (!names)
+			return -ENOMEM;
+
+		pctl_desc->npins = ngpios;
+		pctl_desc->pins = pins;
+
+		for (p = names, i = 0; i < ngpios; i++, p += PIN_NAM_SZ) {
+			struct sgpio_port_addr addr;
+
+			sgpio_pin_to_addr(priv, i, &addr);
+			snprintf(p, PIN_NAM_SZ, "SGPIO_%c_p%db%d",
+				 is_input ? 'I' : 'O',
+				 addr.port, addr.bit);
+			pins[i].number = i;
+			pins[i].name = p;
+		}
+	} else
+		return -ENOMEM;
+
+	pctldev = devm_pinctrl_register(dev, pctl_desc, bank);
+	if (IS_ERR(pctldev)) {
+		dev_err(dev, "Failed to register pinctrl\n");
+		return PTR_ERR(pctldev);
+	}
+
+	gc			= &bank->gpio;
+	gc->label		= pctl_desc->name;
+	gc->parent		= dev;
+	gc->of_node		= to_of_node(fwnode);
+	gc->owner		= THIS_MODULE;
+	gc->get_direction	= microchip_sgpio_get_direction;
+	gc->direction_input	= microchip_sgpio_direction_input;
+	gc->direction_output	= microchip_sgpio_direction_output;
+	gc->get			= microchip_sgpio_get_value;
+	gc->set			= microchip_sgpio_set_value;
+	gc->request		= gpiochip_generic_request;
+	gc->free		= gpiochip_generic_free;
+	gc->of_xlate		= microchip_sgpio_of_xlate;
+	gc->of_gpio_n_cells     = 3;
+	gc->base		= -1;
+	gc->ngpio		= ngpios;
+
+	ret = devm_gpiochip_add_data(dev, gc, bank);
+	if (ret == 0)
+		dev_info(dev, "Registered %d GPIOs\n", ngpios);
+	else
+		dev_err(dev, "Failed to register: ret %d\n", ret);
+
+	return ret;
+}
+
+static int microchip_sgpio_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct fwnode_handle *fwnode;
+	struct sgpio_priv *priv;
+	int div_clock = 0, ret, port;
+	u32 val;
+	struct resource *regs;
+	struct clk *clk;
+	int i, nbanks;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = dev;
+
+	/* Get clock */
+	clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(clk)) {
+		dev_err(dev, "Failed to get clock\n");
+		return PTR_ERR(clk);
+	}
+	div_clock = clk_get_rate(clk);
+	if (device_property_read_u32(dev, "bus-frequency", &priv->clock))
+		priv->clock = 12500000;
+	if (priv->clock <= 0 || priv->clock > (div_clock / 2)) {
+		dev_err(dev, "Invalid frequency %d\n", priv->clock);
+		return -EINVAL;
+	}
+
+	/* Get register map */
+	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->regs = devm_ioremap_resource(dev, regs);
+	if (IS_ERR(priv->regs))
+		return PTR_ERR(priv->regs);
+	priv->properties = of_device_get_match_data(dev);
+
+	/* Get rest of device properties */
+	ret = microchip_sgpio_get_ports(priv);
+	if (ret)
+		return ret;
+
+	nbanks = device_get_child_node_count(dev);
+	if (nbanks != 2) {
+		dev_err(dev, "Must have 2 banks (have %d)\n", nbanks);
+		return -EINVAL;
+	}
+
+	i = 0;
+	device_for_each_child_node(dev, fwnode) {
+		ret = microchip_sgpio_register_bank(dev, priv, fwnode, i++);
+		if (ret)
+			return ret;
+	}
+
+	if (priv->in.gpio.ngpio != priv->out.gpio.ngpio) {
+		dev_err(dev, "Banks must have same GPIO count\n");
+		return -EINVAL;
+	}
+
+	sgpio_clrsetbits(priv, REG_SIO_CONFIG, 0,
+			 SGPIO_M_CFG_SIO_PORT_WIDTH(priv),
+			 SGPIO_F_CFG_SIO_PORT_WIDTH(priv, priv->bitcount - 1) |
+			 SGPIO_M_CFG_SIO_AUTO_REPEAT(priv));
+	val = max(2U, div_clock / priv->clock);
+	sgpio_clrsetbits(priv, REG_SIO_CLOCK, 0,
+			 SGPIO_M_CLOCK_SIO_CLK_FREQ(priv),
+			 SGPIO_F_CLOCK_SIO_CLK_FREQ(priv, val));
+
+	for (port = 0; port < SGPIO_BITS_PER_WORD; port++)
+		sgpio_writel(priv, 0, REG_PORT_CONFIG, port);
+	sgpio_writel(priv, priv->ports, REG_PORT_ENABLE, 0);
+
+	return 0;
+}
+
+static const struct of_device_id microchip_sgpio_gpio_of_match[] = {
+	{
+		.compatible = "microchip,sparx5-sgpio",
+		.data = &properties_sparx5,
+	}, {
+		.compatible = "mscc,luton-sgpio",
+		.data = &properties_luton,
+	}, {
+		.compatible = "mscc,ocelot-sgpio",
+		.data = &properties_ocelot,
+	}, {
+		/* sentinel */
+	}
+};
+
+static struct platform_driver microchip_sgpio_pinctrl_driver = {
+	.driver = {
+		.name = "pinctrl-microchip-sgpio",
+		.of_match_table = microchip_sgpio_gpio_of_match,
+		.suppress_bind_attrs = true,
+	},
+	.probe = microchip_sgpio_probe,
+};
+builtin_platform_driver(microchip_sgpio_pinctrl_driver);
-- 
2.25.1

[PATCH v6 3/3] arm64: dts: sparx5: Add SGPIO devices

[Lars Povlsen]

This adds SGPIO devices for the Sparx5 SoC and configures it for the
applicable reference boards.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 arch/arm64/boot/dts/microchip/sparx5.dtsi     |  91 ++++++
 .../boot/dts/microchip/sparx5_pcb125.dts      |   5 +
 .../dts/microchip/sparx5_pcb134_board.dtsi    | 258 ++++++++++++++++++
 .../dts/microchip/sparx5_pcb135_board.dtsi    |  55 ++++
 4 files changed, 409 insertions(+)

diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index 1def30e6b728..d64621d1213b 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -231,6 +231,22 @@ si2_pins: si2-pins {
 				function = "si2";
 			};
 
+			sgpio0_pins: sgpio-pins {
+				pins = "GPIO_0", "GPIO_1", "GPIO_2", "GPIO_3";
+				function = "sg0";
+			};
+
+			sgpio1_pins: sgpio1-pins {
+				pins = "GPIO_4", "GPIO_5", "GPIO_12", "GPIO_13";
+				function = "sg1";
+			};
+
+			sgpio2_pins: sgpio2-pins {
+				pins = "GPIO_30", "GPIO_31", "GPIO_32",
+				       "GPIO_33";
+				function = "sg2";
+			};
+
 			uart_pins: uart-pins {
 				pins = "GPIO_10", "GPIO_11";
 				function = "uart";
@@ -261,6 +277,81 @@ emmc_pins: emmc-pins {
 			};
 		};
 
+		sgpio0: gpio@61101036c {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "microchip,sparx5-sgpio";
+			status = "disabled";
+			clocks = <&sys_clk>;
+			pinctrl-0 = <&sgpio0_pins>;
+			pinctrl-names = "default";
+			reg = <0x6 0x1101036c 0x100>;
+			sgpio_in0: gpio@0 {
+				compatible = "microchip,sparx5-sgpio-bank";
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <3>;
+				ngpios = <96>;
+			};
+			sgpio_out0: gpio@1 {
+				compatible = "microchip,sparx5-sgpio-bank";
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <3>;
+				ngpios = <96>;
+			};
+		};
+
+		sgpio1: gpio@611010484 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "microchip,sparx5-sgpio";
+			status = "disabled";
+			clocks = <&sys_clk>;
+			pinctrl-0 = <&sgpio1_pins>;
+			pinctrl-names = "default";
+			reg = <0x6 0x11010484 0x100>;
+			sgpio_in1: gpio@0 {
+				compatible = "microchip,sparx5-sgpio-bank";
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <3>;
+				ngpios = <96>;
+			};
+			sgpio_out1: gpio@1 {
+				compatible = "microchip,sparx5-sgpio-bank";
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <3>;
+				ngpios = <96>;
+			};
+		};
+
+		sgpio2: gpio@61101059c {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "microchip,sparx5-sgpio";
+			status = "disabled";
+			clocks = <&sys_clk>;
+			pinctrl-0 = <&sgpio2_pins>;
+			pinctrl-names = "default";
+			reg = <0x6 0x1101059c 0x100>;
+			sgpio_in2: gpio@0 {
+				reg = <0>;
+				compatible = "microchip,sparx5-sgpio-bank";
+				gpio-controller;
+				#gpio-cells = <3>;
+				ngpios = <96>;
+			};
+			sgpio_out2: gpio@1 {
+				compatible = "microchip,sparx5-sgpio-bank";
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <3>;
+				ngpios = <96>;
+			};
+		};
+
 		i2c0: i2c@600101000 {
 			compatible = "snps,designware-i2c";
 			status = "disabled";
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts b/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
index 6b2da7c7520c..9baa085d7861 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
@@ -69,6 +69,11 @@ spi-flash@9 {
 	};
 };
 
+&sgpio0 {
+	status = "okay";
+	microchip,sgpio-port-ranges = <0 23>;
+};
+
 &i2c1 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
index 35984785d611..4f1512b0e871 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
@@ -36,6 +36,242 @@ gpio-restart {
 		gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
 		priority = <200>;
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		led@0 {
+			label = "twr0:green";
+			gpios = <&sgpio_out0 8 0 GPIO_ACTIVE_LOW>;
+		};
+		led@1 {
+			label = "twr0:yellow";
+			gpios = <&sgpio_out0 8 1 GPIO_ACTIVE_LOW>;
+		};
+		led@2 {
+			label = "twr1:green";
+			gpios = <&sgpio_out0 9 0 GPIO_ACTIVE_LOW>;
+		};
+		led@3 {
+			label = "twr1:yellow";
+			gpios = <&sgpio_out0 9 1 GPIO_ACTIVE_LOW>;
+		};
+		led@4 {
+			label = "twr2:green";
+			gpios = <&sgpio_out0 10 0 GPIO_ACTIVE_LOW>;
+		};
+		led@5 {
+			label = "twr2:yellow";
+			gpios = <&sgpio_out0 10 1 GPIO_ACTIVE_LOW>;
+		};
+		led@6 {
+			label = "twr3:green";
+			gpios = <&sgpio_out0 11 0 GPIO_ACTIVE_LOW>;
+		};
+		led@7 {
+			label = "twr3:yellow";
+			gpios = <&sgpio_out0 11 1 GPIO_ACTIVE_LOW>;
+		};
+		led@8 {
+			label = "eth12:green";
+			gpios = <&sgpio_out0 12 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@9 {
+			label = "eth12:yellow";
+			gpios = <&sgpio_out0 12 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@10 {
+			label = "eth13:green";
+			gpios = <&sgpio_out0 13 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@11 {
+			label = "eth13:yellow";
+			gpios = <&sgpio_out0 13 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@12 {
+			label = "eth14:green";
+			gpios = <&sgpio_out0 14 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@13 {
+			label = "eth14:yellow";
+			gpios = <&sgpio_out0 14 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@14 {
+			label = "eth15:green";
+			gpios = <&sgpio_out0 15 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@15 {
+			label = "eth15:yellow";
+			gpios = <&sgpio_out0 15 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@16 {
+			label = "eth48:green";
+			gpios = <&sgpio_out1 16 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@17 {
+			label = "eth48:yellow";
+			gpios = <&sgpio_out1 16 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@18 {
+			label = "eth49:green";
+			gpios = <&sgpio_out1 17 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@19 {
+			label = "eth49:yellow";
+			gpios = <&sgpio_out1 17 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@20 {
+			label = "eth50:green";
+			gpios = <&sgpio_out1 18 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@21 {
+			label = "eth50:yellow";
+			gpios = <&sgpio_out1 18 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@22 {
+			label = "eth51:green";
+			gpios = <&sgpio_out1 19 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@23 {
+			label = "eth51:yellow";
+			gpios = <&sgpio_out1 19 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@24 {
+			label = "eth52:green";
+			gpios = <&sgpio_out1 20 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@25 {
+			label = "eth52:yellow";
+			gpios = <&sgpio_out1 20 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@26 {
+			label = "eth53:green";
+			gpios = <&sgpio_out1 21 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@27 {
+			label = "eth53:yellow";
+			gpios = <&sgpio_out1 21 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@28 {
+			label = "eth54:green";
+			gpios = <&sgpio_out1 22 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@29 {
+			label = "eth54:yellow";
+			gpios = <&sgpio_out1 22 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@30 {
+			label = "eth55:green";
+			gpios = <&sgpio_out1 23 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@31 {
+			label = "eth55:yellow";
+			gpios = <&sgpio_out1 23 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@32 {
+			label = "eth56:green";
+			gpios = <&sgpio_out1 24 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@33 {
+			label = "eth56:yellow";
+			gpios = <&sgpio_out1 24 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@34 {
+			label = "eth57:green";
+			gpios = <&sgpio_out1 25 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@35 {
+			label = "eth57:yellow";
+			gpios = <&sgpio_out1 25 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@36 {
+			label = "eth58:green";
+			gpios = <&sgpio_out1 26 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@37 {
+			label = "eth58:yellow";
+			gpios = <&sgpio_out1 26 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@38 {
+			label = "eth59:green";
+			gpios = <&sgpio_out1 27 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@39 {
+			label = "eth59:yellow";
+			gpios = <&sgpio_out1 27 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@40 {
+			label = "eth60:green";
+			gpios = <&sgpio_out1 28 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@41 {
+			label = "eth60:yellow";
+			gpios = <&sgpio_out1 28 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@42 {
+			label = "eth61:green";
+			gpios = <&sgpio_out1 29 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@43 {
+			label = "eth61:yellow";
+			gpios = <&sgpio_out1 29 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@44 {
+			label = "eth62:green";
+			gpios = <&sgpio_out1 30 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@45 {
+			label = "eth62:yellow";
+			gpios = <&sgpio_out1 30 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@46 {
+			label = "eth63:green";
+			gpios = <&sgpio_out1 31 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led@47 {
+			label = "eth63:yellow";
+			gpios = <&sgpio_out1 31 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
 };
 
 &spi0 {
@@ -54,6 +290,28 @@ spi-flash@9 {
 	};
 };
 
+&sgpio0 {
+	status = "okay";
+	microchip,sgpio-port-ranges = <8 15>;
+	gpio@0 {
+		ngpios = <64>;
+	};
+	gpio@1 {
+		ngpios = <64>;
+	};
+};
+
+&sgpio1 {
+	status = "okay";
+	microchip,sgpio-port-ranges = <24 31>;
+	gpio@0 {
+		ngpios = <64>;
+	};
+	gpio@1 {
+		ngpios = <64>;
+	};
+};
+
 &gpio {
 	i2cmux_pins_i: i2cmux-pins-i {
 	       pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19",
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index 7de66806b14b..66381271bef9 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -20,6 +20,50 @@ gpio-restart {
 		gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
 		priority = <200>;
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		led@0 {
+			label = "eth60:yellow";
+			gpios = <&sgpio_out1 28 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led@1 {
+			label = "eth60:green";
+			gpios = <&sgpio_out1 28 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led@2 {
+			label = "eth61:yellow";
+			gpios = <&sgpio_out1 29 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led@3 {
+			label = "eth61:green";
+			gpios = <&sgpio_out1 29 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led@4 {
+			label = "eth62:yellow";
+			gpios = <&sgpio_out1 30 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led@5 {
+			label = "eth62:green";
+			gpios = <&sgpio_out1 30 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led@6 {
+			label = "eth63:yellow";
+			gpios = <&sgpio_out1 31 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led@7 {
+			label = "eth63:green";
+			gpios = <&sgpio_out1 31 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
 };
 
 &gpio {
@@ -67,6 +111,17 @@ spi-flash@9 {
 	};
 };
 
+&sgpio1 {
+	status = "okay";
+	microchip,sgpio-port-ranges = <24 31>;
+	gpio@0 {
+		ngpios = <64>;
+	};
+	gpio@1 {
+		ngpios = <64>;
+	};
+};
+
 &axi {
 	i2c0_imux: i2c0-imux@0 {
 		compatible = "i2c-mux-pinctrl";
-- 
2.25.1

Re: [PATCH v6 2/3] pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO

[Andy Shevchenko]

On Wed, Oct 14, 2020 at 6:25 PM Lars Povlsen <lars.povlsen@microchip.com> wrote:
>
> This adds a pinctrl driver for the Microsemi/Microchip Serial GPIO
> (SGPIO) device used in various SoC's.

...

> +#define PIN_NAM_SZ     (sizeof("SGPIO_D_pXXbY")+1)

+1 for what?

...

> +#define __shf(x)               (__builtin_ffsll(x) - 1)
> +#define __BF_PREP(bf, x)       (bf & ((x) << __shf(bf)))
> +#define __BF_GET(bf, x)                (((x & bf) >> __shf(bf)))

This smells like bitfield.h.

...

> +static int sgpio_input_get(struct sgpio_priv *priv,
> +                          struct sgpio_port_addr *addr)
> +{

> +       int ret;
> +
> +       ret = !!(sgpio_readl(priv, REG_INPUT_DATA, addr->bit) &
> +                BIT(addr->port));
> +
> +       return ret;

Sounds like one line.

> +}

> +static int sgpio_get_functions_count(struct pinctrl_dev *pctldev)
> +{

> +       return 1;

I didn't get why it's not a pure GPIO driver?
It has only one function (no pinmux).
I didn't find any pin control features either.

What did I miss?

...

> +static int microchip_sgpio_get_value(struct gpio_chip *gc, unsigned int gpio)
> +{
> +       struct sgpio_bank *bank = gpiochip_get_data(gc);
> +       struct sgpio_priv *priv = bank->priv;
> +       struct sgpio_port_addr addr;

> +       int ret;

No need.

> +
> +       sgpio_pin_to_addr(priv, gpio, &addr);
> +
> +       if (bank->is_input)
> +               ret = sgpio_input_get(priv, &addr);
> +       else
> +               ret = sgpio_output_get(priv, &addr);
> +
> +       return ret;
> +}


...


> +       ret = devm_gpiochip_add_data(dev, gc, bank);
> +       if (ret == 0)

> +               dev_info(dev, "Registered %d GPIOs\n", ngpios);

No noise.

> +       else
> +               dev_err(dev, "Failed to register: ret %d\n", ret);
> +

...

> +       /* Get register map */
> +       regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +       priv->regs = devm_ioremap_resource(dev, regs);

devm_platform_ioremap_resource();

> +       if (IS_ERR(priv->regs))
> +               return PTR_ERR(priv->regs);

> +       priv->properties = of_device_get_match_data(dev);

It's interesting you have a mix between OF APIs and device property
APIs. Choose one. If you stick with OF, use of_property_ and so,
otherwise replace of_*() by corresponding device_*() or generic calls.

Can you use gpio-regmap APIs?

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v6 2/3] pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO

[Lars Povlsen]

Hi Andy!

Andy Shevchenko writes:

> On Wed, Oct 14, 2020 at 6:25 PM Lars Povlsen <lars.povlsen@microchip.com> wrote:
>>
>> This adds a pinctrl driver for the Microsemi/Microchip Serial GPIO
>> (SGPIO) device used in various SoC's.
>
> ...
>
>> +#define PIN_NAM_SZ     (sizeof("SGPIO_D_pXXbY")+1)
>
> +1 for what?
>

Reverse fencepost :-). I'll remove it.

> ...
>
>> +#define __shf(x)               (__builtin_ffsll(x) - 1)
>> +#define __BF_PREP(bf, x)       (bf & ((x) << __shf(bf)))
>> +#define __BF_GET(bf, x)                (((x & bf) >> __shf(bf)))
>
> This smells like bitfield.h.
>

Yes, and I would use it if I could, just bitfield.h don't like anything
but constexpr. The driver support 3 SoC variants which (unfortunately)
have different register layouts in some areas.

> ...
>
>> +static int sgpio_input_get(struct sgpio_priv *priv,
>> +                          struct sgpio_port_addr *addr)
>> +{
>
>> +       int ret;
>> +
>> +       ret = !!(sgpio_readl(priv, REG_INPUT_DATA, addr->bit) &
>> +                BIT(addr->port));
>> +
>> +       return ret;
>
> Sounds like one line.
>

Yes, I'll change that.

>> +}
>
>> +static int sgpio_get_functions_count(struct pinctrl_dev *pctldev)
>> +{
>
>> +       return 1;
>
> I didn't get why it's not a pure GPIO driver?
> It has only one function (no pinmux).
> I didn't find any pin control features either.
>
> What did I miss?

The hardware has more functions, which are planned to be added
later. This has already been agreed with Linux Walleij.

>
> ...
>
>> +static int microchip_sgpio_get_value(struct gpio_chip *gc, unsigned int gpio)
>> +{
>> +       struct sgpio_bank *bank = gpiochip_get_data(gc);
>> +       struct sgpio_priv *priv = bank->priv;
>> +       struct sgpio_port_addr addr;
>
>> +       int ret;
>
> No need.

Ok, I'll trim it.

>
>> +
>> +       sgpio_pin_to_addr(priv, gpio, &addr);
>> +
>> +       if (bank->is_input)
>> +               ret = sgpio_input_get(priv, &addr);
>> +       else
>> +               ret = sgpio_output_get(priv, &addr);
>> +
>> +       return ret;
>> +}
>
>
> ...
>
>
>> +       ret = devm_gpiochip_add_data(dev, gc, bank);
>> +       if (ret == 0)
>
>> +               dev_info(dev, "Registered %d GPIOs\n", ngpios);
>
> No noise.
>

OK, gone.

>> +       else
>> +               dev_err(dev, "Failed to register: ret %d\n", ret);
>> +
>
> ...
>
>> +       /* Get register map */
>> +       regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +       priv->regs = devm_ioremap_resource(dev, regs);
>
> devm_platform_ioremap_resource();

Yes, I'll replace with that.

>
>> +       if (IS_ERR(priv->regs))
>> +               return PTR_ERR(priv->regs);
>
>> +       priv->properties = of_device_get_match_data(dev);
>
> It's interesting you have a mix between OF APIs and device property
> APIs. Choose one. If you stick with OF, use of_property_ and so,
> otherwise replace of_*() by corresponding device_*() or generic calls.

Sure. I will change the device_property_read_u32() with
of_property_read_u32().

>
> Can you use gpio-regmap APIs?

No, I think the sgpio hardware is a little too odd for that
(of_gpio_n_cells == 3). And then there's alternate pinctrl functions.

Thank you for your comments, they are very much appreciated. Let me know
if I missed anything.

I will refresh the series shortly (on v5.10-rc1).

---Lars

-- 
Lars Povlsen,
Microchip