From: Linus Walleij <linus.walleij@linaro.org>
To: MyungJoo Ham <myungjoo.ham@samsung.com>,
Chanwoo Choi <cw00.choi@samsung.com>
Cc: linux-kernel@vger.kernel.org,
Linus Walleij <linus.walleij@linaro.org>,
devicetree@vger.kernel.org
Subject: [PATCH 1/2] extcon: fsa9480: Rewrite bindings in YAML and extend
Date: Sun, 1 Nov 2020 01:43:56 +0100 [thread overview]
Message-ID: <20201101004357.1076876-1-linus.walleij@linaro.org> (raw)
This rewrites the FSA9480 DT bindings using YAML and
extends them with the compatible TI TSU6111.
I chose to name the file fcs,fsa880 since this is the
first switch, later versions are improvements.
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
.../bindings/extcon/extcon-fsa9480.txt | 21 --------
.../bindings/extcon/fcs,fsa880.yaml | 52 +++++++++++++++++++
2 files changed, 52 insertions(+), 21 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt
create mode 100644 Documentation/devicetree/bindings/extcon/fcs,fsa880.yaml
diff --git a/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt b/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt
deleted file mode 100644
index 624bd76f468e..000000000000
--- a/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt
+++ /dev/null
@@ -1,21 +0,0 @@
-FAIRCHILD SEMICONDUCTOR FSA9480 MICROUSB SWITCH
-
-The FSA9480 is a USB port accessory detector and switch. The FSA9480 is fully
-controlled using I2C and enables USB data, stereo and mono audio, video,
-microphone, and UART data to use a common connector port.
-
-Required properties:
- - compatible : Must be one of
- "fcs,fsa9480"
- "fcs,fsa880"
- - reg : Specifies i2c slave address. Must be 0x25.
- - interrupts : Should contain one entry specifying interrupt signal of
- interrupt parent to which interrupt pin of the chip is connected.
-
- Example:
- musb@25 {
- compatible = "fcs,fsa9480";
- reg = <0x25>;
- interrupt-parent = <&gph2>;
- interrupts = <7 0>;
- };
diff --git a/Documentation/devicetree/bindings/extcon/fcs,fsa880.yaml b/Documentation/devicetree/bindings/extcon/fcs,fsa880.yaml
new file mode 100644
index 000000000000..ef6a246a1337
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/fcs,fsa880.yaml
@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/fcs,fsa880.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Fairchild Semiconductor FSA880, FSA9480 and compatibles
+
+maintainers:
+ - Linus Walleij <linus.walleij@linaro.org>
+
+description:
+ The FSA880 and FSA9480 are USB port accessory detectors and switches.
+ The switch is fully controlled using I2C and enables USB data, stereo
+ and mono audio, video, microphone, and UART data to use a common
+ connector port. Compatible switches exist from other manufacturers.
+
+properties:
+ compatible:
+ enum:
+ - fcs,fsa880
+ - fcs,fsa9480
+ - ti,tsu6111
+
+ reg:
+ maxItems: 1
+ description: The I2C address for an FSA880 compatible device is
+ usually 0x25.
+
+ interrupts:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ usb-switch@25 {
+ compatible = "fcs,fsa880";
+ reg = <0x25>;
+ interrupt-parent = <&gpio>;
+ interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+ };
+ };
--
2.26.2
next reply other threads:[~2020-11-01 0:44 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <CGME20201101004410epcas1p36f8a3469611fbc27eed6803d383df06e@epcas1p3.samsung.com>
2020-11-01 0:43 ` Linus Walleij [this message]
2020-11-01 0:43 ` [PATCH 2/2] extcon: fsa9480: Support TI TSU6111 variant Linus Walleij
2020-11-02 3:01 ` Chanwoo Choi
2020-11-05 1:02 ` Chanwoo Choi
2020-11-02 2:59 ` [PATCH 1/2] extcon: fsa9480: Rewrite bindings in YAML and extend Chanwoo Choi
2020-11-04 22:31 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201101004357.1076876-1-linus.walleij@linaro.org \
--to=linus.walleij@linaro.org \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=myungjoo.ham@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).