LKML Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH 0/2] DA9121 regulator support
@ 2020-10-29 15:15 Vincent Whitchurch
  2020-10-29 15:15 ` [PATCH 1/2] dt-bindings: regulator: Add DA9121 Vincent Whitchurch
  2020-10-29 15:15 ` [PATCH 2/2] regulator: Add support for DA9121 regulator Vincent Whitchurch
  0 siblings, 2 replies; 5+ messages in thread
From: Vincent Whitchurch @ 2020-10-29 15:15 UTC (permalink / raw)
  To: lgirdwood, broonie, support.opensource
  Cc: kernel, devicetree, linux-kernel, robh+dt, Vincent Whitchurch

This series adds support for the DA9121, a "High-Performance, 10 A, Dual-Phase
DC-DC Converter".  The datasheet is currently available here:

 https://www.dialog-semiconductor.com/sites/default/files/da9121_datasheet_2v3.pdf

Vincent Whitchurch (2):
  dt-bindings: regulator: Add DA9121
  regulator: Add support for DA9121 regulator

 .../bindings/regulator/dlg,da9121.yaml        |  42 +++++++
 drivers/regulator/Kconfig                     |  12 ++
 drivers/regulator/Makefile                    |   1 +
 drivers/regulator/da9121-regulator.c          | 111 ++++++++++++++++++
 4 files changed, 166 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/dlg,da9121.yaml
 create mode 100644 drivers/regulator/da9121-regulator.c

-- 
2.28.0


^ permalink raw reply	[flat|nested] 5+ messages in thread

* [PATCH 1/2] dt-bindings: regulator: Add DA9121
  2020-10-29 15:15 [PATCH 0/2] DA9121 regulator support Vincent Whitchurch
@ 2020-10-29 15:15 ` Vincent Whitchurch
  2020-10-29 15:15 ` [PATCH 2/2] regulator: Add support for DA9121 regulator Vincent Whitchurch
  1 sibling, 0 replies; 5+ messages in thread
From: Vincent Whitchurch @ 2020-10-29 15:15 UTC (permalink / raw)
  To: lgirdwood, broonie, support.opensource
  Cc: kernel, devicetree, linux-kernel, robh+dt, Vincent Whitchurch

Add bindings for the Dialog Semiconductor DA9121 voltage regulator.

Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
---
 .../bindings/regulator/dlg,da9121.yaml        | 42 +++++++++++++++++++
 1 file changed, 42 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/dlg,da9121.yaml

diff --git a/Documentation/devicetree/bindings/regulator/dlg,da9121.yaml b/Documentation/devicetree/bindings/regulator/dlg,da9121.yaml
new file mode 100644
index 000000000000..2e67cc164da9
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/dlg,da9121.yaml
@@ -0,0 +1,42 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/dlg,da9121.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Dialog Semiconductor DA9121 voltage regulator
+
+maintainers:
+  - Vincent Whitchurch <vincent.whitchurch@axis.com>
+
+allOf:
+  - $ref: regulator.yaml#
+
+properties:
+  compatible:
+    const: dlg,da9121
+
+  reg:
+    maxItems: 1
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      regulator@68 {
+        compatible = "dlg,da9121";
+        reg = <0x68>;
+
+        regulator-min-microvolt = <675000>;
+        regulator-max-microvolt = <825000>;
+      };
+    };
+
+...
-- 
2.28.0


^ permalink raw reply	[flat|nested] 5+ messages in thread

* [PATCH 2/2] regulator: Add support for DA9121 regulator
  2020-10-29 15:15 [PATCH 0/2] DA9121 regulator support Vincent Whitchurch
  2020-10-29 15:15 ` [PATCH 1/2] dt-bindings: regulator: Add DA9121 Vincent Whitchurch
@ 2020-10-29 15:15 ` Vincent Whitchurch
  2020-10-29 15:28   ` Mark Brown
  1 sibling, 1 reply; 5+ messages in thread
From: Vincent Whitchurch @ 2020-10-29 15:15 UTC (permalink / raw)
  To: lgirdwood, broonie, support.opensource
  Cc: kernel, devicetree, linux-kernel, robh+dt, Vincent Whitchurch

Add support for the Dialog Semiconductor DA9121, a single-channel
dual-phase buck converter controlled via I2C.

Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
---
 drivers/regulator/Kconfig            |  12 +++
 drivers/regulator/Makefile           |   1 +
 drivers/regulator/da9121-regulator.c | 111 +++++++++++++++++++++++++++
 3 files changed, 124 insertions(+)
 create mode 100644 drivers/regulator/da9121-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 020a00d6696b..005a6036dd38 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -303,6 +303,18 @@ config REGULATOR_DA9063
 	  This driver can also be built as a module. If so, the module
 	  will be called da9063-regulator.
 
+config REGULATOR_DA9121
+	tristate "Dialog Semiconductor DA9121 regulator"
+	depends on I2C && OF
+	select REGMAP_I2C
+	help
+	  Say y here to support for the Dialog Semiconductor DA9121.  The
+	  DA9210 is a dual-phase buck converter controlled through an I2C
+	  interface.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called da9121-regulator.
+
 config REGULATOR_DA9210
 	tristate "Dialog Semiconductor DA9210 regulator"
 	depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 6ebae516258e..6096862a1d60 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_REGULATOR_DA9052)	+= da9052-regulator.o
 obj-$(CONFIG_REGULATOR_DA9055)	+= da9055-regulator.o
 obj-$(CONFIG_REGULATOR_DA9062)	+= da9062-regulator.o
 obj-$(CONFIG_REGULATOR_DA9063)	+= da9063-regulator.o
+obj-$(CONFIG_REGULATOR_DA9121) += da9121-regulator.o
 obj-$(CONFIG_REGULATOR_DA9210) += da9210-regulator.o
 obj-$(CONFIG_REGULATOR_DA9211) += da9211-regulator.o
 obj-$(CONFIG_REGULATOR_DBX500_PRCMU) += dbx500-prcmu.o
diff --git a/drivers/regulator/da9121-regulator.c b/drivers/regulator/da9121-regulator.c
new file mode 100644
index 000000000000..d712e8f07c41
--- /dev/null
+++ b/drivers/regulator/da9121-regulator.c
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* Copyright (C) 2020 Axis Communications AB */
+
+#include <linux/of_device.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/driver.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+
+#define DA9121_BUCK_BUCK1_0			0x20
+#define DA9121_BUCK_BUCK1_0_CH1_EN		BIT(0)
+
+#define DA9121_BUCK_BUCK1_5			0x25
+#define DA9121_BUCK_BUCK1_5_CH1_A_VOUT		GENMASK(7, 0)
+
+#define DA9121_MIN_MV		300
+#define DA9121_MAX_MV		1900
+#define DA9121_STEP_MV		10
+#define DA9121_MIN_SEL		(DA9121_MIN_MV / DA9121_STEP_MV)
+#define DA9121_N_VOLTAGES	(((DA9121_MAX_MV - DA9121_MIN_MV) / DA9121_STEP_MV) \
+				 + 1 + DA9121_MIN_SEL)
+
+static const struct regmap_config da9121_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+};
+
+static const struct regulator_ops da9121_buck_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.list_voltage = regulator_list_voltage_linear,
+};
+
+static const struct regulator_desc da9121_reg = {
+	.name = "da9121",
+	.owner = THIS_MODULE,
+	.ops = &da9121_buck_ops,
+	.type = REGULATOR_VOLTAGE,
+	.n_voltages = DA9121_N_VOLTAGES,
+	.min_uV = DA9121_MIN_MV * 1000,
+	.uV_step = DA9121_STEP_MV * 1000,
+	.linear_min_sel = DA9121_MIN_SEL,
+	.vsel_reg = DA9121_BUCK_BUCK1_5,
+	.vsel_mask = DA9121_BUCK_BUCK1_5_CH1_A_VOUT,
+	.enable_reg = DA9121_BUCK_BUCK1_0,
+	.enable_mask = DA9121_BUCK_BUCK1_0_CH1_EN,
+	/* Default value of BUCK_BUCK1_0.CH1_SRC_DVC_UP */
+	.ramp_delay = 20000,
+	/* tBUCK_EN */
+	.enable_time = 20,
+};
+
+static const struct of_device_id da9121_dt_ids[] = {
+	{ .compatible = "dlg,da9121", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, da9121_dt_ids);
+
+static int da9121_i2c_probe(struct i2c_client *i2c,
+			    const struct i2c_device_id *id)
+{
+	struct device *dev = &i2c->dev;
+	struct regulator_config config = {};
+	struct regulator_dev *rdev;
+	struct regmap *regmap;
+
+	regmap = devm_regmap_init_i2c(i2c, &da9121_regmap_config);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	config.dev = &i2c->dev;
+	config.of_node = dev->of_node;
+	config.regmap = regmap;
+
+	config.init_data = of_get_regulator_init_data(dev, dev->of_node, &da9121_reg);
+	if (!config.init_data)
+		return -ENOMEM;
+
+	rdev = devm_regulator_register(&i2c->dev, &da9121_reg, &config);
+	if (IS_ERR(rdev)) {
+		dev_err(&i2c->dev, "Failed to register da9121 regulator\n");
+		return PTR_ERR(rdev);
+	}
+
+	return 0;
+}
+
+static const struct i2c_device_id da9121_i2c_id[] = {
+	{ "da9121", 0 },
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, da9121_i2c_id);
+
+static struct i2c_driver da9121_regulator_driver = {
+	.driver = {
+		.name = "da9121",
+		.of_match_table = of_match_ptr(da9121_dt_ids),
+	},
+	.probe = da9121_i2c_probe,
+	.id_table = da9121_i2c_id,
+};
+
+module_i2c_driver(da9121_regulator_driver);
+
+MODULE_LICENSE("GPL v2");
-- 
2.28.0


^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: [PATCH 2/2] regulator: Add support for DA9121 regulator
  2020-10-29 15:15 ` [PATCH 2/2] regulator: Add support for DA9121 regulator Vincent Whitchurch
@ 2020-10-29 15:28   ` Mark Brown
  2020-11-02 15:48     ` Vincent Whitchurch
  0 siblings, 1 reply; 5+ messages in thread
From: Mark Brown @ 2020-10-29 15:28 UTC (permalink / raw)
  To: Vincent Whitchurch
  Cc: lgirdwood, support.opensource, kernel, devicetree, linux-kernel, robh+dt


[-- Attachment #1: Type: text/plain, Size: 380 bytes --]

On Thu, Oct 29, 2020 at 04:15:38PM +0100, Vincent Whitchurch wrote:

> +	config.init_data = of_get_regulator_init_data(dev, dev->of_node, &da9121_reg);
> +	if (!config.init_data)
> +		return -ENOMEM;

Don't do this, the core can do the DT bit for you and there is no reason
not to register the device if there are no constraints.  -ENOMEM would
also be the wrong error code here.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: [PATCH 2/2] regulator: Add support for DA9121 regulator
  2020-10-29 15:28   ` Mark Brown
@ 2020-11-02 15:48     ` Vincent Whitchurch
  0 siblings, 0 replies; 5+ messages in thread
From: Vincent Whitchurch @ 2020-11-02 15:48 UTC (permalink / raw)
  To: Mark Brown
  Cc: lgirdwood, support.opensource, kernel, devicetree, linux-kernel, robh+dt

On Thu, Oct 29, 2020 at 03:28:43PM +0000, Mark Brown wrote:
> On Thu, Oct 29, 2020 at 04:15:38PM +0100, Vincent Whitchurch wrote:
> 
> > +	config.init_data = of_get_regulator_init_data(dev, dev->of_node, &da9121_reg);
> > +	if (!config.init_data)
> > +		return -ENOMEM;
> 
> Don't do this, the core can do the DT bit for you and there is no reason
> not to register the device if there are no constraints.  -ENOMEM would
> also be the wrong error code here.

OK, thanks.  I see that I can get the core to do it if I set ->of_match
on the regulator_desc.  I also see that there is some flexibility about
the placement of the constraints (desc->regulators_node is optional).

This chip has only one output which the datasheet calls Buck1, so I will
remove this call and set the desc.of_match field to get the driver to
support a node which looks like this:

      regulator@68 {
        compatible = "dlg,da9121";
        reg = <0x68>;

        buck1 {
            regulator-min-microvolt = <675000>;
            regulator-max-microvolt = <825000>;
        };
      };

^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, back to index

Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-10-29 15:15 [PATCH 0/2] DA9121 regulator support Vincent Whitchurch
2020-10-29 15:15 ` [PATCH 1/2] dt-bindings: regulator: Add DA9121 Vincent Whitchurch
2020-10-29 15:15 ` [PATCH 2/2] regulator: Add support for DA9121 regulator Vincent Whitchurch
2020-10-29 15:28   ` Mark Brown
2020-11-02 15:48     ` Vincent Whitchurch

LKML Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/lkml/0 lkml/git/0.git
	git clone --mirror https://lore.kernel.org/lkml/1 lkml/git/1.git
	git clone --mirror https://lore.kernel.org/lkml/2 lkml/git/2.git
	git clone --mirror https://lore.kernel.org/lkml/3 lkml/git/3.git
	git clone --mirror https://lore.kernel.org/lkml/4 lkml/git/4.git
	git clone --mirror https://lore.kernel.org/lkml/5 lkml/git/5.git
	git clone --mirror https://lore.kernel.org/lkml/6 lkml/git/6.git
	git clone --mirror https://lore.kernel.org/lkml/7 lkml/git/7.git
	git clone --mirror https://lore.kernel.org/lkml/8 lkml/git/8.git
	git clone --mirror https://lore.kernel.org/lkml/9 lkml/git/9.git
	git clone --mirror https://lore.kernel.org/lkml/10 lkml/git/10.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 lkml lkml/ https://lore.kernel.org/lkml \
		linux-kernel@vger.kernel.org
	public-inbox-index lkml

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-kernel


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git