linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Lee Jones <lee.jones@linaro.org>
To: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>,
	ohad@wizery.com, bjorn.andersson@linaro.org, s-anna@ti.com,
	linux-remoteproc@vger.kernel.org, robh+dt@kernel.org,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	praneeth@ti.com, rogerq@ti.com
Subject: Re: [PATCH v3 3/6] remoteproc: pru: Add support for PRU specific interrupt configuration
Date: Tue, 8 Dec 2020 11:04:30 +0000	[thread overview]
Message-ID: <20201208110430.GS4801@dell> (raw)
In-Reply-To: <20201207173731.GA1509079@xps15>

On Mon, 07 Dec 2020, Mathieu Poirier wrote:

> On Fri, Dec 04, 2020 at 09:18:04PM +0100, Grzegorz Jaszczyk wrote:
> > The firmware blob can contain optional ELF sections: .resource_table
> > section and .pru_irq_map one. The second one contains the PRUSS
> > interrupt mapping description, which needs to be setup before powering
> > on the PRU core. To avoid RAM wastage this ELF section is not mapped to
> > any ELF segment (by the firmware linker) and therefore is not loaded to
> > PRU memory.
> > 
> > The PRU interrupt configuration is handled within the PRUSS INTC irqchip
> > driver and leverages the system events to interrupt channels and host
> > interrupts mapping configuration. Relevant irq routing information is
> > passed through a special .pru_irq_map ELF section (for interrupts routed
> > to and used by PRU cores) or via the PRU application's device tree node
> > (for interrupts routed to and used by the main CPU). The mappings are
> > currently programmed during the booting/shutdown of the PRU.
> > 
> > The interrupt configuration passed through .pru_irq_map ELF section is
> > optional. It varies on specific firmware functionality and therefore
> > have to be unwinded during PRU stop and performed again during
> > PRU start.
> > 
> > Co-developed-by: Suman Anna <s-anna@ti.com>
> > Signed-off-by: Suman Anna <s-anna@ti.com>
> > Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
> > ---

[...]

> >  drivers/remoteproc/pru_rproc.c | 180 +++++++++++++++++++++++++++++++++
> >  drivers/remoteproc/pru_rproc.h |  46 +++++++++
> >  2 files changed, 226 insertions(+)
> >  create mode 100644 drivers/remoteproc/pru_rproc.h
> > 
> > diff --git a/drivers/remoteproc/pru_rproc.c b/drivers/remoteproc/pru_rproc.c
> > index d33392bbd8af..4ef59d15d888 100644
> > --- a/drivers/remoteproc/pru_rproc.c
> > +++ b/drivers/remoteproc/pru_rproc.c
> > @@ -11,13 +11,16 @@
> >   */

[...]

> > +static int pru_handle_intrmap(struct rproc *rproc)
> > +{
> > +	struct device *dev = rproc->dev.parent;
> > +	struct pru_rproc *pru = rproc->priv;
> > +	struct pru_irq_rsc *rsc = pru->pru_interrupt_map;
> > +	struct irq_fwspec fwspec;
> > +	struct device_node *irq_parent;
> > +	int i, ret = 0;
> > +
> > +	/* not having pru_interrupt_map is not an error */
> > +	if (!rsc)
> > +		return 0;
> > +
> > +	/* currently supporting only type 0 */
> > +	if (rsc->type != 0) {
> > +		dev_err(dev, "unsupported rsc type: %d\n", rsc->type);
> > +		return -EINVAL;
> > +	}
> > +
> > +	if (rsc->num_evts > MAX_PRU_SYS_EVENTS)
> > +		return -EINVAL;
> > +
> > +	if (sizeof(*rsc) + rsc->num_evts * sizeof(struct pruss_int_map) !=
> > +	    pru->pru_interrupt_map_sz)
> > +		return -EINVAL;
> > +
> > +	pru->evt_count = rsc->num_evts;
> > +	pru->mapped_irq = kcalloc(pru->evt_count, sizeof(int), GFP_KERNEL);
> 
> sizeof(unsigned int)

Would you mind trimming your replies please?

Brain grepping through 200+ lines of quote for a one line review
comment is a little frustrating.

TIA.

-- 
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog

  reply	other threads:[~2020-12-08 11:05 UTC|newest]

Thread overview: 10+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-12-04 20:18 [PATCH v3 0/6] Add a PRU remoteproc driver Grzegorz Jaszczyk
2020-12-04 20:18 ` [PATCH v3 1/6] dt-bindings: remoteproc: Add binding doc for PRU cores in the PRU-ICSS Grzegorz Jaszczyk
2020-12-04 20:18 ` [PATCH v3 2/6] remoteproc: pru: Add a PRU remoteproc driver Grzegorz Jaszczyk
2020-12-04 20:18 ` [PATCH v3 3/6] remoteproc: pru: Add support for PRU specific interrupt configuration Grzegorz Jaszczyk
2020-12-07 17:37   ` Mathieu Poirier
2020-12-08 11:04     ` Lee Jones [this message]
2020-12-08 14:03     ` Grzegorz Jaszczyk
2020-12-04 20:18 ` [PATCH v3 4/6] remoteproc: pru: Add pru-specific debugfs support Grzegorz Jaszczyk
2020-12-04 20:18 ` [PATCH v3 5/6] remoteproc: pru: Add support for various PRU cores on K3 AM65x SoCs Grzegorz Jaszczyk
2020-12-04 20:18 ` [PATCH v3 6/6] remoteproc: pru: Add support for various PRU cores on K3 J721E SoCs Grzegorz Jaszczyk

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20201208110430.GS4801@dell \
    --to=lee.jones@linaro.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=grzegorz.jaszczyk@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=linux-remoteproc@vger.kernel.org \
    --cc=mathieu.poirier@linaro.org \
    --cc=ohad@wizery.com \
    --cc=praneeth@ti.com \
    --cc=robh+dt@kernel.org \
    --cc=rogerq@ti.com \
    --cc=s-anna@ti.com \
    --subject='Re: [PATCH v3 3/6] remoteproc: pru: Add support for PRU specific interrupt configuration' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).