linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
To: linux-media@vger.kernel.org, devicetree@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-doc@vger.kernel.org,
	devel@driverdev.osuosl.org, linux-sunxi@googlegroups.com
Cc: Yong Deng <yong.deng@magewell.com>,
	Mauro Carvalho Chehab <mchehab@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
	Jernej Skrabec <jernej.skrabec@siol.net>,
	Paul Kocialkowski <paul.kocialkowski@bootlin.com>,
	Jonathan Corbet <corbet@lwn.net>,
	Kishon Vijay Abraham I <kishon@ti.com>,
	Vinod Koul <vkoul@kernel.org>,
	Helen Koike <helen.koike@collabora.com>,
	Dafna Hirschfeld <dafna.hirschfeld@collabora.com>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Philipp Zabel <p.zabel@pengutronix.de>,
	Sakari Ailus <sakari.ailus@linux.intel.com>,
	Hans Verkuil <hans.verkuil@cisco.com>,
	Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
	kevin.lhopital@hotmail.com
Subject: [PATCH v3 02/15] phy: Distinguish between Rx and Tx for MIPI D-PHY with submodes
Date: Fri, 11 Dec 2020 16:56:55 +0100	[thread overview]
Message-ID: <20201211155708.154710-3-paul.kocialkowski@bootlin.com> (raw)
In-Reply-To: <20201211155708.154710-1-paul.kocialkowski@bootlin.com>

As some D-PHY controllers support both Rx and Tx mode, we need a way for
users to explicitly request one or the other. For instance, Rx mode can
be used along with MIPI CSI-2 while Tx mode can be used with MIPI DSI.

Introduce new MIPI D-PHY PHY submodes to use with PHY_MODE_MIPI_DPHY.
The default (zero value) is kept to Tx so only the rkisp1 driver, which
uses D-PHY in Rx mode, needs to be adapted.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
---
 drivers/staging/media/rkisp1/rkisp1-isp.c |  3 ++-
 include/linux/phy/phy-mipi-dphy.h         | 13 +++++++++++++
 2 files changed, 15 insertions(+), 1 deletion(-)

diff --git a/drivers/staging/media/rkisp1/rkisp1-isp.c b/drivers/staging/media/rkisp1/rkisp1-isp.c
index a9715b0b7264..f1167995688a 100644
--- a/drivers/staging/media/rkisp1/rkisp1-isp.c
+++ b/drivers/staging/media/rkisp1/rkisp1-isp.c
@@ -914,7 +914,8 @@ static int rkisp1_mipi_csi2_start(struct rkisp1_isp *isp,
 
 	phy_mipi_dphy_get_default_config(pixel_clock, isp->sink_fmt->bus_width,
 					 sensor->lanes, cfg);
-	phy_set_mode(sensor->dphy, PHY_MODE_MIPI_DPHY);
+	phy_set_mode_ext(cdev->dphy, PHY_MODE_MIPI_DPHY,
+			 PHY_MIPI_DPHY_SUBMODE_RX);
 	phy_configure(sensor->dphy, &opts);
 	phy_power_on(sensor->dphy);
 
diff --git a/include/linux/phy/phy-mipi-dphy.h b/include/linux/phy/phy-mipi-dphy.h
index a877ffee845d..0f57ef46a8b5 100644
--- a/include/linux/phy/phy-mipi-dphy.h
+++ b/include/linux/phy/phy-mipi-dphy.h
@@ -6,6 +6,19 @@
 #ifndef __PHY_MIPI_DPHY_H_
 #define __PHY_MIPI_DPHY_H_
 
+/**
+ * enum phy_mipi_dphy_submode - MIPI D-PHY sub-mode
+ *
+ * A MIPI D-PHY can be used to transmit or receive data.
+ * Since some controllers can support both, the direction to enable is specified
+ * with the PHY sub-mode. Transmit is assumed by default with phy_set_mode.
+ */
+
+enum phy_mipi_dphy_submode {
+	PHY_MIPI_DPHY_SUBMODE_TX = 0,
+	PHY_MIPI_DPHY_SUBMODE_RX,
+};
+
 /**
  * struct phy_configure_opts_mipi_dphy - MIPI D-PHY configuration set
  *
-- 
2.29.2


  parent reply	other threads:[~2020-12-11 17:00 UTC|newest]

Thread overview: 23+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-12-11 15:56 [PATCH v3 00/15] Allwinner MIPI CSI-2 support for A31/V3s/A83T Paul Kocialkowski
2020-12-11 15:56 ` [PATCH v3 01/15] docs: phy: Add a part about PHY mode and submode Paul Kocialkowski
2020-12-11 15:56 ` Paul Kocialkowski [this message]
2020-12-11 15:56 ` [PATCH v3 03/15] phy: allwinner: phy-sun6i-mipi-dphy: Support D-PHY Rx mode for MIPI CSI-2 Paul Kocialkowski
2020-12-11 15:56 ` [PATCH v3 04/15] media: sun6i-csi: Use common V4L2 format info for storage bpp Paul Kocialkowski
2020-12-11 15:56 ` [PATCH v3 05/15] media: sun6i-csi: Only configure the interface data width for parallel Paul Kocialkowski
2020-12-11 15:56 ` [PATCH v3 06/15] dt-bindings: media: sun6i-a31-csi: Add MIPI CSI-2 input port Paul Kocialkowski
2020-12-14 23:12   ` Rob Herring
2020-12-11 15:57 ` [PATCH v3 07/15] media: sun6i-csi: Add support for MIPI CSI-2 bridge input Paul Kocialkowski
2020-12-14 11:34   ` Maxime Ripard
2020-12-11 15:57 ` [PATCH v3 08/15] dt-bindings: media: Add A31 MIPI CSI-2 bindings documentation Paul Kocialkowski
2020-12-14 11:35   ` Maxime Ripard
2020-12-14 23:14     ` Rob Herring
2020-12-11 15:57 ` [PATCH v3 09/15] media: sunxi: Add support for the A31 MIPI CSI-2 controller Paul Kocialkowski
2020-12-14 11:39   ` Maxime Ripard
2020-12-31 12:54     ` Paul Kocialkowski
2020-12-11 15:57 ` [PATCH v3 10/15] ARM: dts: sun8i: v3s: Add nodes for MIPI CSI-2 support Paul Kocialkowski
2020-12-11 15:57 ` [PATCH v3 11/15] MAINTAINERS: Add entry for the Allwinner A31 MIPI CSI-2 bridge Paul Kocialkowski
2020-12-11 15:57 ` [PATCH v3 12/15] dt-bindings: media: Add A83T MIPI CSI-2 bindings documentation Paul Kocialkowski
2020-12-11 15:57 ` [PATCH v3 13/15] media: sunxi: Add support for the A83T MIPI CSI-2 controller Paul Kocialkowski
2020-12-14 11:41   ` Maxime Ripard
2020-12-11 15:57 ` [PATCH v3 14/15] ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller node Paul Kocialkowski
2020-12-11 15:57 ` [PATCH v3 15/15] MAINTAINERS: Add entry for the Allwinner A83T MIPI CSI-2 bridge Paul Kocialkowski

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20201211155708.154710-3-paul.kocialkowski@bootlin.com \
    --to=paul.kocialkowski@bootlin.com \
    --cc=corbet@lwn.net \
    --cc=dafna.hirschfeld@collabora.com \
    --cc=devel@driverdev.osuosl.org \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=hans.verkuil@cisco.com \
    --cc=helen.koike@collabora.com \
    --cc=jernej.skrabec@siol.net \
    --cc=kevin.lhopital@hotmail.com \
    --cc=kishon@ti.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-doc@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=linux-sunxi@googlegroups.com \
    --cc=mchehab@kernel.org \
    --cc=mripard@kernel.org \
    --cc=p.zabel@pengutronix.de \
    --cc=robh+dt@kernel.org \
    --cc=sakari.ailus@linux.intel.com \
    --cc=thomas.petazzoni@bootlin.com \
    --cc=vkoul@kernel.org \
    --cc=wens@csie.org \
    --cc=yong.deng@magewell.com \
    --subject='Re: [PATCH v3 02/15] phy: Distinguish between Rx and Tx for MIPI D-PHY with submodes' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).