[PATCH V2 0/2] Broadcom's PMB (Power Management Bus) support

[PATCH V2 0/2] Broadcom's PMB (Power Management Bus) support

[Rafał Miłecki]

From: Rafał Miłecki <rafal@milecki.pl>

PMB is a hardware block used for powering SoC devices like PCIe, USB,
SATA. Initially I planned to treat it as a reset controller and Philipp
pointed out in review that PMB driver should use a power subsystem.

This is my refactored support.

***

Please note one difference when compared to the initial reset attempt.

As I store info about SoC devices in the driver now, I had to put
support for multiple buses there. That's required to avoid things like:

compatible = "brcm,bcm4908-pmb-no-1";
compatible = "brcm,bcm4908-pmb-no-2";

So now a single "reg" covers bigger buses (e.g. 0x40) in size, see:

reg = <0x802800e0 0x40>;

Other SoCs my use something like:

reg = <0x802800e0 0x20>;
reg = <0x802800e0 0x60>;

***

AFAIU this should go through Florian's tree. I based in on top of the
soc-arm64/next.

V2: Use drivers/soc/bcm/bcm63xx/ and add Kconfig help message

Rafał Miłecki (2):
  dt-bindings: power: document Broadcom's PMB binding
  soc: bcm: add PM driver for Broadcom's PMB

 .../bindings/power/brcm,bcm-pmb.yaml          |  50 +++
 MAINTAINERS                                   |  10 +
 drivers/soc/bcm/Makefile                      |   2 +-
 drivers/soc/bcm/bcm63xx/Kconfig               |   9 +
 drivers/soc/bcm/bcm63xx/Makefile              |   1 +
 drivers/soc/bcm/bcm63xx/bcm-pmb.c             | 333 ++++++++++++++++++
 include/dt-bindings/soc/bcm-pmb.h             |  11 +
 7 files changed, 415 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/power/brcm,bcm-pmb.yaml
 create mode 100644 drivers/soc/bcm/bcm63xx/bcm-pmb.c
 create mode 100644 include/dt-bindings/soc/bcm-pmb.h

-- 
2.26.2

[PATCH V2 1/2] dt-bindings: power: document Broadcom's PMB binding

[Rafał Miłecki]

From: Rafał Miłecki <rafal@milecki.pl>

Broadcom's PMB is power controller used for disabling and enabling SoC
devices.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
---
 .../bindings/power/brcm,bcm-pmb.yaml          | 50 +++++++++++++++++++
 include/dt-bindings/soc/bcm-pmb.h             | 11 ++++
 2 files changed, 61 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/power/brcm,bcm-pmb.yaml
 create mode 100644 include/dt-bindings/soc/bcm-pmb.h

diff --git a/Documentation/devicetree/bindings/power/brcm,bcm-pmb.yaml b/Documentation/devicetree/bindings/power/brcm,bcm-pmb.yaml
new file mode 100644
index 000000000000..40b08d83c80b
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/brcm,bcm-pmb.yaml
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/brcm,bcm-pmb.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom PMB (Power Management Bus) controller
+
+description: This document describes Broadcom's PMB controller. It supports
+  powering various types of connected devices (e.g. PCIe, USB, SATA).
+
+maintainers:
+  - Rafał Miłecki <rafal@milecki.pl>
+
+properties:
+  compatible:
+    enum:
+      - brcm,bcm4908-pmb
+
+  reg:
+    description: register space of one or more buses
+    maxItems: 1
+
+  big-endian:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: Flag to use for block working in big endian mode.
+
+  "#power-domain-cells":
+    description: cell specifies device ID (see bcm-pmb.h)
+    const: 1
+
+required:
+  - reg
+  - "#power-domain-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/soc/bcm-pmb.h>
+
+    pmb: power-controller@802800e0 {
+        compatible = "brcm,bcm4908-pmb";
+        reg = <0x802800e0 0x40>;
+        #power-domain-cells = <1>;
+    };
+
+    foo {
+        power-domains = <&pmb BCM_PMB_PCIE0>;
+    };
diff --git a/include/dt-bindings/soc/bcm-pmb.h b/include/dt-bindings/soc/bcm-pmb.h
new file mode 100644
index 000000000000..744dc3af4d41
--- /dev/null
+++ b/include/dt-bindings/soc/bcm-pmb.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT */
+
+#ifndef __DT_BINDINGS_SOC_BCM_PMB_H
+#define __DT_BINDINGS_SOC_BCM_PMB_H
+
+#define BCM_PMB_PCIE0				0x01
+#define BCM_PMB_PCIE1				0x02
+#define BCM_PMB_PCIE2				0x03
+#define BCM_PMB_HOST_USB			0x04
+
+#endif
-- 
2.26.2

[PATCH V2 2/2] soc: bcm: add PM driver for Broadcom's PMB

[Rafał Miłecki]

From: Rafał Miłecki <rafal@milecki.pl>

PMB originally comes from BCM63138 but can be also found on many other
chipsets (e.g. BCM4908). It's needed to power on and off SoC blocks like
PCIe, SATA, USB.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
---
V2: Use drivers/soc/bcm/bcm63xx/
    Add help to the config BCM_PMB
    Drop debugging print
---
 MAINTAINERS                       |  10 +
 drivers/soc/bcm/Makefile          |   2 +-
 drivers/soc/bcm/bcm63xx/Kconfig   |   9 +
 drivers/soc/bcm/bcm63xx/Makefile  |   1 +
 drivers/soc/bcm/bcm63xx/bcm-pmb.c | 333 ++++++++++++++++++++++++++++++
 5 files changed, 354 insertions(+), 1 deletion(-)
 create mode 100644 drivers/soc/bcm/bcm63xx/bcm-pmb.c

diff --git a/MAINTAINERS b/MAINTAINERS
index e73636b75f29..75140f0d1541 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3656,6 +3656,16 @@ L:	linux-mips@vger.kernel.org
 S:	Maintained
 F:	drivers/firmware/broadcom/*
 
+BROADCOM PMB (POWER MANAGEMENT BUS) DRIVER
+M:	Rafał Miłecki <rafal@milecki.pl>
+M:	Florian Fainelli <f.fainelli@gmail.com>
+M:	bcm-kernel-feedback-list@broadcom.com
+L:	linux-pm@vger.kernel.org
+S:	Maintained
+T:	git git://github.com/broadcom/stblinux.git
+F:	drivers/soc/bcm/bcm-pmb.c
+F:	include/dt-bindings/soc/bcm-pmb.h
+
 BROADCOM SPECIFIC AMBA DRIVER (BCMA)
 M:	Rafał Miłecki <zajec5@gmail.com>
 L:	linux-wireless@vger.kernel.org
diff --git a/drivers/soc/bcm/Makefile b/drivers/soc/bcm/Makefile
index 7bc90e0bd773..0f0efa28d92b 100644
--- a/drivers/soc/bcm/Makefile
+++ b/drivers/soc/bcm/Makefile
@@ -1,5 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0-only
 obj-$(CONFIG_BCM2835_POWER)	+= bcm2835-power.o
 obj-$(CONFIG_RASPBERRYPI_POWER)	+= raspberrypi-power.o
-obj-$(CONFIG_SOC_BCM63XX)	+= bcm63xx/
+obj-y				+= bcm63xx/
 obj-$(CONFIG_SOC_BRCMSTB)	+= brcmstb/
diff --git a/drivers/soc/bcm/bcm63xx/Kconfig b/drivers/soc/bcm/bcm63xx/Kconfig
index 16f648a6c70a..9e501c8ac5ce 100644
--- a/drivers/soc/bcm/bcm63xx/Kconfig
+++ b/drivers/soc/bcm/bcm63xx/Kconfig
@@ -10,3 +10,12 @@ config BCM63XX_POWER
 	  BCM6318, BCM6328, BCM6362 and BCM63268 SoCs.
 
 endif # SOC_BCM63XX
+
+config BCM_PMB
+	bool "Broadcom PMB (Power Management Bus) driver"
+	depends on ARCH_BCM4908 || (COMPILE_TEST && OF)
+	default ARCH_BCM4908
+	select PM_GENERIC_DOMAINS if PM
+	help
+	  This enables support for the Broadcom's PMB (Power Management Bus) that
+	  is used for disabling and enabling SoC devices.
diff --git a/drivers/soc/bcm/bcm63xx/Makefile b/drivers/soc/bcm/bcm63xx/Makefile
index 0710d5e018cc..557eed3d67bd 100644
--- a/drivers/soc/bcm/bcm63xx/Makefile
+++ b/drivers/soc/bcm/bcm63xx/Makefile
@@ -1,2 +1,3 @@
 # SPDX-License-Identifier: GPL-2.0-only
 obj-$(CONFIG_BCM63XX_POWER) += bcm63xx-power.o
+obj-$(CONFIG_BCM_PMB)		+= bcm-pmb.o
diff --git a/drivers/soc/bcm/bcm63xx/bcm-pmb.c b/drivers/soc/bcm/bcm63xx/bcm-pmb.c
new file mode 100644
index 000000000000..c223023dc64f
--- /dev/null
+++ b/drivers/soc/bcm/bcm63xx/bcm-pmb.c
@@ -0,0 +1,333 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2013 Broadcom
+ * Copyright (C) 2020 Rafał Miłecki <rafal@milecki.pl>
+ */
+
+#include <dt-bindings/soc/bcm-pmb.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <linux/reset/bcm63xx_pmb.h>
+
+#define BPCM_ID_REG					0x00
+#define BPCM_CAPABILITIES				0x04
+#define  BPCM_CAP_NUM_ZONES				0x000000ff
+#define  BPCM_CAP_SR_REG_BITS				0x0000ff00
+#define  BPCM_CAP_PLLTYPE				0x00030000
+#define  BPCM_CAP_UBUS					0x00080000
+#define BPCM_CONTROL					0x08
+#define BPCM_STATUS					0x0c
+#define BPCM_ROSC_CONTROL				0x10
+#define BPCM_ROSC_THRESH_H				0x14
+#define BPCM_ROSC_THRESHOLD_BCM6838			0x14
+#define BPCM_ROSC_THRESH_S				0x18
+#define BPCM_ROSC_COUNT_BCM6838				0x18
+#define BPCM_ROSC_COUNT					0x1c
+#define BPCM_PWD_CONTROL_BCM6838			0x1c
+#define BPCM_PWD_CONTROL				0x20
+#define BPCM_SR_CONTROL_BCM6838				0x20
+#define BPCM_PWD_ACCUM_CONTROL				0x24
+#define BPCM_SR_CONTROL					0x28
+#define BPCM_GLOBAL_CONTROL				0x2c
+#define BPCM_MISC_CONTROL				0x30
+#define BPCM_MISC_CONTROL2				0x34
+#define BPCM_SGPHY_CNTL					0x38
+#define BPCM_SGPHY_STATUS				0x3c
+#define BPCM_ZONE0					0x40
+#define  BPCM_ZONE_CONTROL				0x00
+#define   BPCM_ZONE_CONTROL_MANUAL_CLK_EN		0x00000001
+#define   BPCM_ZONE_CONTROL_MANUAL_RESET_CTL		0x00000002
+#define   BPCM_ZONE_CONTROL_FREQ_SCALE_USED		0x00000004	/* R/O */
+#define   BPCM_ZONE_CONTROL_DPG_CAPABLE			0x00000008	/* R/O */
+#define   BPCM_ZONE_CONTROL_MANUAL_MEM_PWR		0x00000030
+#define   BPCM_ZONE_CONTROL_MANUAL_ISO_CTL		0x00000040
+#define   BPCM_ZONE_CONTROL_MANUAL_CTL			0x00000080
+#define   BPCM_ZONE_CONTROL_DPG_CTL_EN			0x00000100
+#define   BPCM_ZONE_CONTROL_PWR_DN_REQ			0x00000200
+#define   BPCM_ZONE_CONTROL_PWR_UP_REQ			0x00000400
+#define   BPCM_ZONE_CONTROL_MEM_PWR_CTL_EN		0x00000800
+#define   BPCM_ZONE_CONTROL_BLK_RESET_ASSERT		0x00001000
+#define   BPCM_ZONE_CONTROL_MEM_STBY			0x00002000
+#define   BPCM_ZONE_CONTROL_RESERVED			0x0007c000
+#define   BPCM_ZONE_CONTROL_PWR_CNTL_STATE		0x00f80000
+#define   BPCM_ZONE_CONTROL_FREQ_SCALAR_DYN_SEL		0x01000000	/* R/O */
+#define   BPCM_ZONE_CONTROL_PWR_OFF_STATE		0x02000000	/* R/O */
+#define   BPCM_ZONE_CONTROL_PWR_ON_STATE		0x04000000	/* R/O */
+#define   BPCM_ZONE_CONTROL_PWR_GOOD			0x08000000	/* R/O */
+#define   BPCM_ZONE_CONTROL_DPG_PWR_STATE		0x10000000	/* R/O */
+#define   BPCM_ZONE_CONTROL_MEM_PWR_STATE		0x20000000	/* R/O */
+#define   BPCM_ZONE_CONTROL_ISO_STATE			0x40000000	/* R/O */
+#define   BPCM_ZONE_CONTROL_RESET_STATE			0x80000000	/* R/O */
+#define  BPCM_ZONE_CONFIG1				0x04
+#define  BPCM_ZONE_CONFIG2				0x08
+#define  BPCM_ZONE_FREQ_SCALAR_CONTROL			0x0c
+#define  BPCM_ZONE_SIZE					0x10
+
+struct bcm_pmb {
+	struct device *dev;
+	void __iomem *base;
+	spinlock_t lock;
+	bool little_endian;
+	struct genpd_onecell_data genpd_onecell_data;
+};
+
+struct bcm_pmb_pd_data {
+	const char * const name;
+	int id;
+	u8 bus;
+	u8 device;
+};
+
+struct bcm_pmb_pm_domain {
+	struct bcm_pmb *pmb;
+	const struct bcm_pmb_pd_data *data;
+	struct generic_pm_domain genpd;
+};
+
+static int bcm_pmb_bpcm_read(struct bcm_pmb *pmb, int bus, u8 device,
+			     int offset, u32 *val)
+{
+	void __iomem *base = pmb->base + bus * 0x20;
+	unsigned long flags;
+	int err;
+
+	spin_lock_irqsave(&pmb->lock, flags);
+	err = bpcm_rd(base, device, offset, val);
+	spin_unlock_irqrestore(&pmb->lock, flags);
+
+	if (!err)
+		*val = pmb->little_endian ? le32_to_cpu(*val) : be32_to_cpu(*val);
+
+	return err;
+}
+
+static int bcm_pmb_bpcm_write(struct bcm_pmb *pmb, int bus, u8 device,
+			      int offset, u32 val)
+{
+	void __iomem *base = pmb->base + bus * 0x20;
+	unsigned long flags;
+	int err;
+
+	val = pmb->little_endian ? cpu_to_le32(val) : cpu_to_be32(val);
+
+	spin_lock_irqsave(&pmb->lock, flags);
+	err = bpcm_wr(base, device, offset, val);
+	spin_unlock_irqrestore(&pmb->lock, flags);
+
+	return err;
+}
+
+static int bcm_pmb_power_off_zone(struct bcm_pmb *pmb, int bus, u8 device,
+				  int zone)
+{
+	int offset;
+	u32 val;
+	int err;
+
+	offset = BPCM_ZONE0 + zone * BPCM_ZONE_SIZE + BPCM_ZONE_CONTROL;
+
+	err = bcm_pmb_bpcm_read(pmb, bus, device, offset, &val);
+	if (err)
+		return err;
+
+	val |= BPCM_ZONE_CONTROL_PWR_DN_REQ;
+	val &= ~BPCM_ZONE_CONTROL_PWR_UP_REQ;
+
+	err = bcm_pmb_bpcm_write(pmb, bus, device, offset, val);
+
+	return err;
+}
+
+static int bcm_pmb_power_on_zone(struct bcm_pmb *pmb, int bus, u8 device,
+				 int zone)
+{
+	int offset;
+	u32 val;
+	int err;
+
+	offset = BPCM_ZONE0 + zone * BPCM_ZONE_SIZE + BPCM_ZONE_CONTROL;
+
+	err = bcm_pmb_bpcm_read(pmb, bus, device, offset, &val);
+	if (err)
+		return err;
+
+	if (!(val & BPCM_ZONE_CONTROL_PWR_ON_STATE)) {
+		val &= ~BPCM_ZONE_CONTROL_PWR_DN_REQ;
+		val |= BPCM_ZONE_CONTROL_DPG_CTL_EN;
+		val |= BPCM_ZONE_CONTROL_PWR_UP_REQ;
+		val |= BPCM_ZONE_CONTROL_MEM_PWR_CTL_EN;
+		val |= BPCM_ZONE_CONTROL_BLK_RESET_ASSERT;
+
+		err = bcm_pmb_bpcm_write(pmb, bus, device, offset, val);
+	}
+
+	return err;
+}
+
+static int bcm_pmb_power_off_device(struct bcm_pmb *pmb, int bus, u8 device)
+{
+	int offset;
+	u32 val;
+	int err;
+
+	/* Entire device can be powered off by powering off the 0th zone */
+	offset = BPCM_ZONE0 + BPCM_ZONE_CONTROL;
+
+	err = bcm_pmb_bpcm_read(pmb, bus, device, offset, &val);
+	if (err)
+		return err;
+
+	if (!(val & BPCM_ZONE_CONTROL_PWR_OFF_STATE)) {
+		val = BPCM_ZONE_CONTROL_PWR_DN_REQ;
+
+		err = bcm_pmb_bpcm_write(pmb, bus, device, offset, val);
+	}
+
+	return err;
+}
+
+static int bcm_pmb_power_on_device(struct bcm_pmb *pmb, int bus, u8 device)
+{
+	u32 val;
+	int err;
+	int i;
+
+	err = bcm_pmb_bpcm_read(pmb, bus, device, BPCM_CAPABILITIES, &val);
+	if (err)
+		return err;
+
+	for (i = 0; i < (val & BPCM_CAP_NUM_ZONES); i++) {
+		err = bcm_pmb_power_on_zone(pmb, bus, device, i);
+		if (err)
+			return err;
+	}
+
+	return err;
+}
+
+static int bcm_pmb_power_on(struct generic_pm_domain *genpd)
+{
+	struct bcm_pmb_pm_domain *pd = container_of(genpd, struct bcm_pmb_pm_domain, genpd);
+	const struct bcm_pmb_pd_data *data = pd->data;
+	struct bcm_pmb *pmb = pd->pmb;
+
+	switch (data->id) {
+	case BCM_PMB_PCIE0:
+	case BCM_PMB_PCIE1:
+	case BCM_PMB_PCIE2:
+		return bcm_pmb_power_on_zone(pmb, data->bus, data->device, 0);
+	case BCM_PMB_HOST_USB:
+		return bcm_pmb_power_on_device(pmb, data->bus, data->device);
+	default:
+		dev_err(pmb->dev, "unsupported device id: %d\n", data->id);
+		return -EINVAL;
+	}
+}
+
+static int bcm_pmb_power_off(struct generic_pm_domain *genpd)
+{
+	struct bcm_pmb_pm_domain *pd = container_of(genpd, struct bcm_pmb_pm_domain, genpd);
+	const struct bcm_pmb_pd_data *data = pd->data;
+	struct bcm_pmb *pmb = pd->pmb;
+
+	switch (data->id) {
+	case BCM_PMB_PCIE0:
+	case BCM_PMB_PCIE1:
+	case BCM_PMB_PCIE2:
+		return bcm_pmb_power_off_zone(pmb, data->bus, data->device, 0);
+	case BCM_PMB_HOST_USB:
+		return bcm_pmb_power_off_device(pmb, data->bus, data->device);
+	default:
+		dev_err(pmb->dev, "unsupported device id: %d\n", data->id);
+		return -EINVAL;
+	}
+}
+
+static int bcm_pmb_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct bcm_pmb_pd_data *table;
+	const struct bcm_pmb_pd_data *e;
+	struct resource *res;
+	struct bcm_pmb *pmb;
+	int max_id;
+	int err;
+
+	pmb = devm_kzalloc(dev, sizeof(*pmb), GFP_KERNEL);
+	if (!pmb)
+		return -ENOMEM;
+
+	pmb->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	pmb->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(pmb->base))
+		return PTR_ERR(pmb->base);
+
+	spin_lock_init(&pmb->lock);
+
+	pmb->little_endian = !of_device_is_big_endian(dev->of_node);
+
+	table = of_device_get_match_data(dev);
+	if (!table)
+		return -EINVAL;
+
+	max_id = 0;
+	for (e = table; e->name; e++)
+		max_id = max(max_id, e->id);
+
+	pmb->genpd_onecell_data.num_domains = max_id + 1;
+	pmb->genpd_onecell_data.domains =
+		devm_kcalloc(dev, pmb->genpd_onecell_data.num_domains,
+			     sizeof(struct generic_pm_domain *), GFP_KERNEL);
+	if (!pmb->genpd_onecell_data.domains)
+		return -ENOMEM;
+
+	for (e = table; e->name; e++) {
+		struct bcm_pmb_pm_domain *pd = devm_kzalloc(dev, sizeof(*pd), GFP_KERNEL);
+
+		pd->pmb = pmb;
+		pd->data = e;
+		pd->genpd.name = e->name;
+		pd->genpd.power_on = bcm_pmb_power_on;
+		pd->genpd.power_off = bcm_pmb_power_off;
+
+		pm_genpd_init(&pd->genpd, NULL, true);
+		pmb->genpd_onecell_data.domains[e->id] = &pd->genpd;
+	}
+
+	err = of_genpd_add_provider_onecell(dev->of_node, &pmb->genpd_onecell_data);
+	if (err) {
+		dev_err(dev, "failed to add genpd provider: %d\n", err);
+		return err;
+	}
+
+	return 0;
+}
+
+static const struct bcm_pmb_pd_data bcm_pmb_bcm4908_data[] = {
+	{ .name = "pcie2", .id = BCM_PMB_PCIE2, .bus = 0, .device = 2, },
+	{ .name = "pcie0", .id = BCM_PMB_PCIE0, .bus = 1, .device = 14, },
+	{ .name = "pcie1", .id = BCM_PMB_PCIE1, .bus = 1, .device = 15, },
+	{ .name = "usb", .id = BCM_PMB_HOST_USB, .bus = 1, .device = 17, },
+	{ },
+};
+
+static const struct of_device_id bcm_pmb_of_match[] = {
+	{ .compatible = "brcm,bcm4908-pmb", .data = &bcm_pmb_bcm4908_data, },
+	{ },
+};
+
+static struct platform_driver bcm_pmb_driver = {
+	.driver = {
+		.name = "bcm-pmb",
+		.of_match_table = bcm_pmb_of_match,
+	},
+	.probe  = bcm_pmb_probe,
+};
+
+builtin_platform_driver(bcm_pmb_driver);
-- 
2.26.2

Re: [PATCH V2 1/2] dt-bindings: power: document Broadcom's PMB binding

[Rob Herring]

On Mon, 14 Dec 2020 19:07:42 +0100, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@milecki.pl>
> 
> Broadcom's PMB is power controller used for disabling and enabling SoC
> devices.
> 
> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
> ---
>  .../bindings/power/brcm,bcm-pmb.yaml          | 50 +++++++++++++++++++
>  include/dt-bindings/soc/bcm-pmb.h             | 11 ++++
>  2 files changed, 61 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/power/brcm,bcm-pmb.yaml
>  create mode 100644 include/dt-bindings/soc/bcm-pmb.h
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH V2 1/2] dt-bindings: power: document Broadcom's PMB binding

[Florian Fainelli]

On 12/14/2020 10:07 AM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@milecki.pl>
> 
> Broadcom's PMB is power controller used for disabling and enabling SoC
> devices.
> 
> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

Acked-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

Re: [PATCH V2 2/2] soc: bcm: add PM driver for Broadcom's PMB

[Florian Fainelli]

On 12/14/2020 10:07 AM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@milecki.pl>
> 
> PMB originally comes from BCM63138 but can be also found on many other
> chipsets (e.g. BCM4908). It's needed to power on and off SoC blocks like
> PCIe, SATA, USB.
> 
> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

From a driver perspective this looks good to me and thanks for putting
it under drivers/soc/bcm/bcm63xx. Ulf, Kevin, I would need an Ack from
you so I can carry this through the Broadcom SoCs pull requests for
v5.12, thanks!
-- 
Florian

Re: [PATCH V2 1/2] dt-bindings: power: document Broadcom's PMB binding

[Ulf Hansson]

On Mon, 14 Dec 2020 at 19:08, Rafał Miłecki <zajec5@gmail.com> wrote:
>
> From: Rafał Miłecki <rafal@milecki.pl>
>
> Broadcom's PMB is power controller used for disabling and enabling SoC
> devices.
>
> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

Apologize for the delay!

Acked-by: Ulf Hansson <ulf.hansson@linaro.org>

Kind regards
Uffe

> ---
>  .../bindings/power/brcm,bcm-pmb.yaml          | 50 +++++++++++++++++++
>  include/dt-bindings/soc/bcm-pmb.h             | 11 ++++
>  2 files changed, 61 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/power/brcm,bcm-pmb.yaml
>  create mode 100644 include/dt-bindings/soc/bcm-pmb.h
>
> diff --git a/Documentation/devicetree/bindings/power/brcm,bcm-pmb.yaml b/Documentation/devicetree/bindings/power/brcm,bcm-pmb.yaml
> new file mode 100644
> index 000000000000..40b08d83c80b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/power/brcm,bcm-pmb.yaml
> @@ -0,0 +1,50 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/power/brcm,bcm-pmb.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Broadcom PMB (Power Management Bus) controller
> +
> +description: This document describes Broadcom's PMB controller. It supports
> +  powering various types of connected devices (e.g. PCIe, USB, SATA).
> +
> +maintainers:
> +  - Rafał Miłecki <rafal@milecki.pl>
> +
> +properties:
> +  compatible:
> +    enum:
> +      - brcm,bcm4908-pmb
> +
> +  reg:
> +    description: register space of one or more buses
> +    maxItems: 1
> +
> +  big-endian:
> +    $ref: /schemas/types.yaml#/definitions/flag
> +    description: Flag to use for block working in big endian mode.
> +
> +  "#power-domain-cells":
> +    description: cell specifies device ID (see bcm-pmb.h)
> +    const: 1
> +
> +required:
> +  - reg
> +  - "#power-domain-cells"
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/soc/bcm-pmb.h>
> +
> +    pmb: power-controller@802800e0 {
> +        compatible = "brcm,bcm4908-pmb";
> +        reg = <0x802800e0 0x40>;
> +        #power-domain-cells = <1>;
> +    };
> +
> +    foo {
> +        power-domains = <&pmb BCM_PMB_PCIE0>;
> +    };
> diff --git a/include/dt-bindings/soc/bcm-pmb.h b/include/dt-bindings/soc/bcm-pmb.h
> new file mode 100644
> index 000000000000..744dc3af4d41
> --- /dev/null
> +++ b/include/dt-bindings/soc/bcm-pmb.h
> @@ -0,0 +1,11 @@
> +/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT */
> +
> +#ifndef __DT_BINDINGS_SOC_BCM_PMB_H
> +#define __DT_BINDINGS_SOC_BCM_PMB_H
> +
> +#define BCM_PMB_PCIE0                          0x01
> +#define BCM_PMB_PCIE1                          0x02
> +#define BCM_PMB_PCIE2                          0x03
> +#define BCM_PMB_HOST_USB                       0x04
> +
> +#endif
> --
> 2.26.2
>

Re: [PATCH V2 2/2] soc: bcm: add PM driver for Broadcom's PMB

[Ulf Hansson]

On Tue, 15 Dec 2020 at 19:24, Florian Fainelli <f.fainelli@gmail.com> wrote:
>
>
>
> On 12/14/2020 10:07 AM, Rafał Miłecki wrote:
> > From: Rafał Miłecki <rafal@milecki.pl>
> >
> > PMB originally comes from BCM63138 but can be also found on many other
> > chipsets (e.g. BCM4908). It's needed to power on and off SoC blocks like
> > PCIe, SATA, USB.
> >
> > Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
>
> From a driver perspective this looks good to me and thanks for putting
> it under drivers/soc/bcm/bcm63xx. Ulf, Kevin, I would need an Ack from
> you so I can carry this through the Broadcom SoCs pull requests for
> v5.12, thanks!

Apologize for the delay!

Acked-by: Ulf Hansson <ulf.hansson@linaro.org>

Kind regards
Uffe

Re: [PATCH V2 0/2] Broadcom's PMB (Power Management Bus) support

[Florian Fainelli]

On 12/14/2020 10:07 AM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@milecki.pl>
> 
> PMB is a hardware block used for powering SoC devices like PCIe, USB,
> SATA. Initially I planned to treat it as a reset controller and Philipp
> pointed out in review that PMB driver should use a power subsystem.
> 
> This is my refactored support.
> 
> ***
> 
> Please note one difference when compared to the initial reset attempt.
> 
> As I store info about SoC devices in the driver now, I had to put
> support for multiple buses there. That's required to avoid things like:
> 
> compatible = "brcm,bcm4908-pmb-no-1";
> compatible = "brcm,bcm4908-pmb-no-2";
> 
> So now a single "reg" covers bigger buses (e.g. 0x40) in size, see:
> 
> reg = <0x802800e0 0x40>;
> 
> Other SoCs my use something like:
> 
> reg = <0x802800e0 0x20>;
> reg = <0x802800e0 0x60>;
> 
> ***
> 
> AFAIU this should go through Florian's tree. I based in on top of the
> soc-arm64/next.
> 
> V2: Use drivers/soc/bcm/bcm63xx/ and add Kconfig help message

Series applied to drivers/next, thanks!
-- 
Florian