From: Lee Jones <lee.jones@linaro.org>
To: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Cc: mazziesaccount@gmail.com,
Sebastian Reichel <sebastian.reichel@collabora.com>,
Linus Walleij <linus.walleij@linaro.org>,
Krzysztof Kozlowski <krzk@kernel.org>,
Dmitry Osipenko <digetx@gmail.com>,
Cong Pham <cpham2403@gmail.com>,
rostokus@gmail.com, fan.chen@mediatek.com,
linux-kernel@vger.kernel.org, linux-pm@vger.kernel.org
Subject: Re: [RFC PATCH v2 4/6] mfd: add BD71827 header
Date: Wed, 16 Dec 2020 08:53:53 +0000 [thread overview]
Message-ID: <20201216085353.GG4776@dell> (raw)
In-Reply-To: <a9b5c999b67213141831bcb9d56d580e31419bec.1607085199.git.matti.vaittinen@fi.rohmeurope.com>
On Fri, 04 Dec 2020, Matti Vaittinen wrote:
> Add BD71827 driver header. For a record - Header is originally
> based on work authored by Cong Pham although not much of original
> work is left now.
>
> Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
> ---
> This patch was not in v1. This brings in some charger registers
> for the BD71827 charger which is in following patches.
>
> include/linux/mfd/rohm-bd71827.h | 295 +++++++++++++++++++++++++++++++
> 1 file changed, 295 insertions(+)
> create mode 100644 include/linux/mfd/rohm-bd71827.h
>
> diff --git a/include/linux/mfd/rohm-bd71827.h b/include/linux/mfd/rohm-bd71827.h
> new file mode 100644
> index 000000000000..0f5a343b10ae
> --- /dev/null
> +++ b/include/linux/mfd/rohm-bd71827.h
> @@ -0,0 +1,295 @@
> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> +/*
> + * Copyright 2016
Out of date.
> + * @author cpham2403@gmail.com
This is not a proper Author: tag.
> + */
> +
> +#ifndef __LINUX_MFD_BD71827_H
> +#define __LINUX_MFD_BD71827_H
You can drop the LINUX part.
> +#include <linux/regmap.h>
> +
> +#define LDO5VSEL_EQ_H 0
> +
> +#ifndef LDO5VSEL_EQ_H
> + #error define LDO5VSEL_EQ_H to 1 when connect to High, to 0 when connect to Low
> +#else
> + #if LDO5VSEL_EQ_H == 1
> + #define BD71827_REG_LDO5_VOLT BD71827_REG_LDO5_VOLT_H
> + #define LDO5_MASK LDO5_H_MASK
> + #elif LDO5VSEL_EQ_H == 0
> + #define BD71827_REG_LDO5_VOLT BD71827_REG_LDO5_VOLT_L
> + #define LDO5_MASK LDO5_L_MASK
> + #else
> + #error Define LDO5VSEL_EQ_H only to 0 or 1
> + #endif
> +#endif
Not a fan of this at all.
What decides which of these to use?
Does this realistically ever change?
> +enum {
> + BD71827_BUCK1 = 0,
Omit the extra ' 's.
> + BD71827_BUCK2,
> + BD71827_BUCK3,
> + BD71827_BUCK4,
> + BD71827_BUCK5,
> + // General Purpose
No C++ comments.
> + BD71827_LDO1,
> + BD71827_LDO2,
> + BD71827_LDO3,
> + BD71827_LDO4,
> + BD71827_LDO5,
> + BD71827_LDO6,
> + // LDO for Secure Non-Volatile Storage
> + BD71827_LDOSNVS,
> + BD71827_REGULATOR_CNT,
> +};
> +
> +#define BD71827_SUPPLY_STATE_ENABLED 0x1
> +
> +#define BD71827_BUCK1_VOLTAGE_NUM 0x3F
> +#define BD71827_BUCK2_VOLTAGE_NUM 0x3F
> +#define BD71827_BUCK3_VOLTAGE_NUM 0x3F
> +#define BD71827_BUCK4_VOLTAGE_NUM 0x1F
> +#define BD71827_BUCK5_VOLTAGE_NUM 0x1F
> +#define BD71827_LDO1_VOLTAGE_NUM 0x3F
> +#define BD71827_LDO2_VOLTAGE_NUM 0x3F
> +#define BD71827_LDO3_VOLTAGE_NUM 0x3F
> +#define BD71827_LDO4_VOLTAGE_NUM 0x3F
> +#define BD71827_LDO5_VOLTAGE_NUM 0x3F
> +#define BD71827_LDO6_VOLTAGE_NUM 0x1
> +#define BD71827_LDOSNVS_VOLTAGE_NUM 0x1
Please pad out these to there are the same amount of digits after the 0x.
> +#define BD71827_GPIO_NUM 2 /* BD71827 have 2 GPO */
"has 2 GPOs"
> +enum {
> + BD71827_REG_DEVICE = 0x00,
> + BD71827_REG_PWRCTRL = 0x01,
> + BD71827_REG_BUCK1_MODE = 0x02,
> + BD71827_REG_BUCK2_MODE = 0x03,
> + BD71827_REG_BUCK3_MODE = 0x04,
> + BD71827_REG_BUCK4_MODE = 0x05,
> + BD71827_REG_BUCK5_MODE = 0x06,
> + BD71827_REG_BUCK1_VOLT_RUN = 0x07,
> + BD71827_REG_BUCK1_VOLT_SUSP = 0x08,
> + BD71827_REG_BUCK2_VOLT_RUN = 0x09,
> + BD71827_REG_BUCK2_VOLT_SUSP = 0x0A,
> + BD71827_REG_BUCK3_VOLT = 0x0B,
> + BD71827_REG_BUCK4_VOLT = 0x0C,
> + BD71827_REG_BUCK5_VOLT = 0x0D,
> + BD71827_REG_LED_CTRL = 0x0E,
> + BD71827_REG_reserved_0F = 0x0F,
> + BD71827_REG_LDO_MODE1 = 0x10,
> + BD71827_REG_LDO_MODE2 = 0x11,
> + BD71827_REG_LDO_MODE3 = 0x12,
> + BD71827_REG_LDO_MODE4 = 0x13,
> + BD71827_REG_LDO1_VOLT = 0x14,
> + BD71827_REG_LDO2_VOLT = 0x15,
> + BD71827_REG_LDO3_VOLT = 0x16,
> + BD71827_REG_LDO4_VOLT = 0x17,
> + BD71827_REG_LDO5_VOLT_H = 0x18,
> + BD71827_REG_LDO5_VOLT_L = 0x19,
> + BD71827_REG_BUCK_PD_DIS = 0x1A,
> + BD71827_REG_LDO_PD_DIS = 0x1B,
> + BD71827_REG_GPIO = 0x1C,
> + BD71827_REG_OUT32K = 0x1D,
> + BD71827_REG_SEC = 0x1E,
> + BD71827_REG_MIN = 0x1F,
> + BD71827_REG_HOUR = 0x20,
> + BD71827_REG_WEEK = 0x21,
> + BD71827_REG_DAY = 0x22,
> + BD71827_REG_MONTH = 0x23,
> + BD71827_REG_YEAR = 0x24,
> + BD71827_REG_ALM0_SEC = 0x25,
> + BD71827_REG_ALM0_MIN = 0x26,
> + BD71827_REG_ALM0_HOUR = 0x27,
> + BD71827_REG_ALM0_WEEK = 0x28,
> + BD71827_REG_ALM0_DAY = 0x29,
> + BD71827_REG_ALM0_MONTH = 0x2A,
> + BD71827_REG_ALM0_YEAR = 0x2B,
> + BD71827_REG_ALM1_SEC = 0x2C,
> + BD71827_REG_ALM1_MIN = 0x2D,
> + BD71827_REG_ALM1_HOUR = 0x2E,
> + BD71827_REG_ALM1_WEEK = 0x2F,
> + BD71827_REG_ALM1_DAY = 0x30,
> + BD71827_REG_ALM1_MONTH = 0x31,
> + BD71827_REG_ALM1_YEAR = 0x32,
> + BD71827_REG_ALM0_MASK = 0x33,
> + BD71827_REG_ALM1_MASK = 0x34,
> + BD71827_REG_ALM2 = 0x35,
> + BD71827_REG_TRIM = 0x36,
> + BD71827_REG_CONF = 0x37,
> + BD71827_REG_SYS_INIT = 0x38,
> + BD71827_REG_CHG_STATE = 0x39,
> + BD71827_REG_CHG_LAST_STATE = 0x3A,
> + BD71827_REG_BAT_STAT = 0x3B,
> + BD71827_REG_DCIN_STAT = 0x3C,
> + BD71827_REG_VSYS_STAT = 0x3D,
> + BD71827_REG_CHG_STAT = 0x3E,
> + BD71827_REG_CHG_WDT_STAT = 0x3F,
> + BD71827_REG_BAT_TEMP = 0x40,
> + BD71827_REG_ILIM_STAT = 0x41,
> + BD71827_REG_DCIN_SET = 0x42,
> + BD71827_REG_DCIN_CLPS = 0x43,
> + BD71827_REG_VSYS_REG = 0x44,
> + BD71827_REG_VSYS_MAX = 0x45,
> + BD71827_REG_VSYS_MIN = 0x46,
> + BD71827_REG_CHG_SET1 = 0x47,
> + BD71827_REG_CHG_SET2 = 0x48,
> + BD71827_REG_CHG_WDT_PRE = 0x49,
> + BD71827_REG_CHG_WDT_FST = 0x4A,
> + BD71827_REG_CHG_IPRE = 0x4B,
> + BD71827_REG_CHG_IFST = 0x4C,
> + BD71827_REG_CHG_IFST_TERM = 0x4D,
> + BD71827_REG_CHG_VPRE = 0x4E,
> + BD71827_REG_CHG_VBAT_1 = 0x4F,
> + BD71827_REG_CHG_VBAT_2 = 0x50,
> + BD71827_REG_CHG_VBAT_3 = 0x51,
> + BD71827_REG_CHG_LED_1 = 0x52,
> + BD71827_REG_VF_TH = 0x53,
> + BD71827_REG_BAT_SET_1 = 0x54,
> + BD71827_REG_BAT_SET_2 = 0x55,
> + BD71827_REG_BAT_SET_3 = 0x56,
> + BD71827_REG_ALM_VBAT_TH_U = 0x57,
> + BD71827_REG_ALM_VBAT_TH_L = 0x58,
> + BD71827_REG_ALM_DCIN_TH = 0x59,
> + BD71827_REG_ALM_VSYS_TH = 0x5A,
> + BD71827_REG_reserved_5B = 0x5B,
> + BD71827_REG_reserved_5C = 0x5C,
> + BD71827_REG_VM_VBAT_U = 0x5D,
> + BD71827_REG_VM_VBAT_L = 0x5E,
> + BD71827_REG_VM_BTMP = 0x5F,
> + BD71827_REG_VM_VTH = 0x60,
> + BD71827_REG_VM_DCIN_U = 0x61,
> + BD71827_REG_VM_DCIN_L = 0x62,
> + BD71827_REG_reserved_63 = 0x63,
> + BD71827_REG_VM_VF = 0x64,
> + BD71827_REG_reserved_65 = 0x65,
> + BD71827_REG_reserved_66 = 0x66,
> + BD71827_REG_VM_OCV_PRE_U = 0x67,
> + BD71827_REG_VM_OCV_PRE_L = 0x68,
> + BD71827_REG_reserved_69 = 0x69,
> + BD71827_REG_reserved_6A = 0x6A,
> + BD71827_REG_VM_OCV_PST_U = 0x6B,
> + BD71827_REG_VM_OCV_PST_L = 0x6C,
> + BD71827_REG_VM_SA_VBAT_U = 0x6D,
> + BD71827_REG_VM_SA_VBAT_L = 0x6E,
> + BD71827_REG_reserved_6F = 0x6F,
> + BD71827_REG_reserved_70 = 0x70,
> + BD71827_REG_CC_CTRL = 0x71,
> + BD71827_REG_CC_BATCAP1_TH_U = 0x72,
> + BD71827_REG_CC_BATCAP1_TH_L = 0x73,
> + BD71827_REG_CC_BATCAP2_TH_U = 0x74,
> + BD71827_REG_CC_BATCAP2_TH_L = 0x75,
> + BD71827_REG_CC_BATCAP3_TH_U = 0x76,
> + BD71827_REG_CC_BATCAP3_TH_L = 0x77,
> + BD71827_REG_CC_STAT = 0x78,
> + BD71827_REG_CC_CCNTD_3 = 0x79,
> + BD71827_REG_CC_CCNTD_2 = 0x7A,
> + BD71827_REG_CC_CCNTD_1 = 0x7B,
> + BD71827_REG_CC_CCNTD_0 = 0x7C,
> + BD71827_REG_CC_CURCD_U = 0x7D,
> + BD71827_REG_CC_CURCD_L = 0x7E,
> + BD71827_REG_CC_OCUR_THR_1 = 0x7F,
> + BD71827_REG_CC_OCUR_DUR_1 = 0x80,
> + BD71827_REG_CC_OCUR_THR_2 = 0x81,
> + BD71827_REG_CC_OCUR_DUR_2 = 0x82,
> + BD71827_REG_CC_OCUR_THR_3 = 0x83,
> + BD71827_REG_CC_OCUR_DUR_3 = 0x84,
> + BD71827_REG_CC_OCUR_MON = 0x85,
> + BD71827_REG_VM_BTMP_OV_THR = 0x86,
> + BD71827_REG_VM_BTMP_OV_DUR = 0x87,
> + BD71827_REG_VM_BTMP_LO_THR = 0x88,
> + BD71827_REG_VM_BTMP_LO_DUR = 0x89,
> + BD71827_REG_VM_BTMP_MON = 0x8A,
> + BD71827_REG_INT_EN_01 = 0x8B,
> + BD71827_REG_INT_EN_02 = 0x8C,
> + BD71827_REG_INT_EN_03 = 0x8D,
> + BD71827_REG_INT_EN_04 = 0x8E,
> + BD71827_REG_INT_EN_05 = 0x8F,
> + BD71827_REG_INT_EN_06 = 0x90,
> + BD71827_REG_INT_EN_07 = 0x91,
> + BD71827_REG_INT_EN_08 = 0x92,
> + BD71827_REG_INT_EN_09 = 0x93,
> + BD71827_REG_INT_EN_10 = 0x94,
> + BD71827_REG_INT_EN_11 = 0x95,
> + BD71827_REG_INT_EN_12 = 0x96,
> + BD71827_REG_INT_STAT = 0x97,
> + BD71827_REG_INT_STAT_01 = 0x98,
> + BD71827_REG_INT_STAT_02 = 0x99,
> + BD71827_REG_INT_STAT_03 = 0x9A,
> + BD71827_REG_INT_STAT_04 = 0x9B,
> + BD71827_REG_INT_STAT_05 = 0x9C,
> + BD71827_REG_INT_STAT_06 = 0x9D,
> + BD71827_REG_INT_STAT_07 = 0x9E,
> + BD71827_REG_INT_STAT_08 = 0x9F,
> + BD71827_REG_INT_STAT_09 = 0xA0,
> + BD71827_REG_INT_STAT_10 = 0xA1,
> + BD71827_REG_INT_STAT_11 = 0xA2,
> + BD71827_REG_INT_STAT_12 = 0xA3,
> + BD71827_REG_INT_UPDATE = 0xA4,
> + BD71827_REG_PWRCTRL2 = 0xA8,
> + BD71827_REG_PWRCTRL3 = 0xA9,
> + BD71827_REG_SWRESET = 0xAA,
> + BD71827_REG_BUCK1_VOLT_IDLE = 0xAB,
> + BD71827_REG_BUCK2_VOLT_IDLE = 0xAC,
> + BD71827_REG_ONEVNT_MODE_1 = 0xAD,
> + BD71827_REG_ONEVNT_MODE_2 = 0xAE,
> + BD71827_REG_RESERVE_0 = 0xB0,
> + BD71827_REG_RESERVE_1 = 0xB1,
> + BD71827_REG_RESERVE_2 = 0xB2,
> + BD71827_REG_RESERVE_3 = 0xB3,
> + BD71827_REG_RESERVE_4 = 0xB4,
> + BD71827_REG_RESERVE_5 = 0xB5,
> + BD71827_REG_RESERVE_6 = 0xB6,
> + BD71827_REG_RESERVE_7 = 0xB7,
> + BD71827_REG_RESERVE_8 = 0xB8,
> + BD71827_REG_RESERVE_9 = 0xB9,
> + BD71827_REG_RESERVE_A = 0xBA,
> + BD71827_REG_RESERVE_B = 0xBB,
> + BD71827_REG_RESERVE_C = 0xBC,
> + BD71827_REG_RESERVE_D = 0xBD,
> + BD71827_REG_RESERVE_E = 0xBE,
> + BD71827_REG_RESERVE_F = 0xBF,
> + BD71827_REG_VM_VSYS_U = 0xC0,
> + BD71827_REG_VM_VSYS_L = 0xC1,
> + BD71827_REG_VM_SA_VSYS_U = 0xC2,
> + BD71827_REG_VM_SA_VSYS_L = 0xC3,
> + BD71827_REG_CC_SA_CURCD_U = 0xC4,
> + BD71827_REG_CC_SA_CURCD_L = 0xC5,
> + BD71827_REG_BATID = 0xC6,
> + BD71827_REG_VM_SA_VBAT_MIN_U = 0xD4,
> + BD71827_REG_VM_SA_VBAT_MIN_L = 0xD5,
> + BD71827_REG_VM_SA_VBAT_MAX_U = 0xD6,
> + BD71827_REG_VM_SA_VBAT_MAX_L = 0xD7,
> + BD71827_REG_VM_SA_VSYS_MIN_U = 0xD8,
> + BD71827_REG_VM_SA_VSYS_MIN_L = 0xD9,
> + BD71827_REG_VM_SA_VSYS_MAX_U = 0xDA,
> + BD71827_REG_VM_SA_VSYS_MAX_L = 0xDB,
> + BD71827_REG_VM_SA_MINMAX_CLR = 0xDC,
> + BD71827_REG_VM_OCV_PWRON_U = 0xDD,
> + BD71827_REG_VM_OCV_PWRON_L = 0xDE,
> + BD71827_REG_REX_CCNTD_3 = 0xE0,
> + BD71827_REG_REX_CCNTD_2 = 0xE1,
> + BD71827_REG_REX_CCNTD_1 = 0xE2,
> + BD71827_REG_REX_CCNTD_0 = 0xE3,
> + BD71827_REG_REX_SA_VBAT_U = 0xE4,
> + BD71827_REG_REX_SA_VBAT_L = 0xE5,
> + BD71827_REG_REX_CTRL_1 = 0xE6,
> + BD71827_REG_REX_CTRL_2 = 0xE7,
> + BD71827_REG_FULL_CCNTD_3 = 0xE8,
> + BD71827_REG_FULL_CCNTD_2 = 0xE9,
> + BD71827_REG_FULL_CCNTD_1 = 0xEA,
> + BD71827_REG_FULL_CCNTD_0 = 0xEB,
> + BD71827_REG_FULL_CTRL = 0xEC,
> + BD71827_REG_CCNTD_CHG_3 = 0xF0,
> + BD71827_REG_CCNTD_CHG_2 = 0xF1,
> + BD71827_REG_INT_EN_13 = 0xF8,
> + BD71827_REG_INT_STAT_13 = 0xF9,
> + BD71827_REG_I2C_MAGIC = 0xFE,
> + BD71827_REG_PRODUCT = 0xFF,
> + BD71827_MAX_REGISTER = 0x100,
> +};
> +
> +#define BD71827_REX_CLR_MASK 0x10
> +
> +#endif /* __LINUX_MFD_BD71827_H */
--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
next prev parent reply other threads:[~2020-12-16 8:54 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-12-04 12:39 [RFC PATCH v2 0/6] power: supply: Add some fuel-gauge logic Matti Vaittinen
2020-12-04 12:41 ` [RFC PATCH v2 1/6] power: supply: add cap2ocv batinfo helper Matti Vaittinen
2020-12-08 8:54 ` Linus Walleij
2020-12-08 9:30 ` Vaittinen, Matti
2020-12-04 12:43 ` [RFC PATCH v2 2/6] power: supply: add sw-gauge for SOC estimation and CC correction Matti Vaittinen
2020-12-04 12:47 ` [RFC PATCH v2 3/6] mfd: prepare to support BD718xx-charger Matti Vaittinen
2020-12-16 8:49 ` Lee Jones
2020-12-04 12:49 ` [RFC PATCH v2 4/6] mfd: add BD71827 header Matti Vaittinen
2020-12-16 8:53 ` Lee Jones [this message]
2020-12-17 9:40 ` Vaittinen, Matti
2020-12-04 12:53 ` [RFC PATCH v2 5/6] power: supply: Add bd718(27/28/78) charger driver Matti Vaittinen
2020-12-04 12:54 ` [RFC PATCH v2 6/6] MFD: bd71828: differentiate bd71828 and bd71827 chargers Matti Vaittinen
2020-12-16 8:55 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201216085353.GG4776@dell \
--to=lee.jones@linaro.org \
--cc=cpham2403@gmail.com \
--cc=digetx@gmail.com \
--cc=fan.chen@mediatek.com \
--cc=krzk@kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=matti.vaittinen@fi.rohmeurope.com \
--cc=mazziesaccount@gmail.com \
--cc=rostokus@gmail.com \
--cc=sebastian.reichel@collabora.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).