From: Erwan Le Ray <erwan.leray@foss.st.com>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Jiri Slaby <jslaby@suse.com>, Rob Herring <robh+dt@kernel.org>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: <linux-serial@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-stm32@st-md-mailman.stormreply.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>,
Erwan Le Ray <erwan.leray@foss.st.com>,
Fabrice Gasnier <fabrice.gasnier@foss.st.com>,
Valentin Caron <valentin.caron@foss.st.com>
Subject: [PATCH v2 2/8] serial: stm32: fix code cleaning warnings and checks
Date: Wed, 6 Jan 2021 17:21:57 +0100 [thread overview]
Message-ID: <20210106162203.28854-3-erwan.leray@foss.st.com> (raw)
In-Reply-To: <20210106162203.28854-1-erwan.leray@foss.st.com>
Fixes checkpatch --strict warnings and checks:
- checkpatch --strict "Unnecessary parentheses"
- checkpatch --strict "Blank lines aren't necessary before a close brace
- checkpatch --strict "Alignment should match open parenthesis"
- checkpatch --strict "Please don't use multiple blank lines"
- checkpatch --strict "Comparison to NULL could be written ..."
- visual check code ordering warning
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index 6248304a001f..a0ef86d71317 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -176,8 +176,7 @@ static int stm32_pending_rx(struct uart_port *port, u32 *sr, int *last_res,
status = dmaengine_tx_status(stm32_port->rx_ch,
stm32_port->rx_ch->cookie,
&state);
- if ((status == DMA_IN_PROGRESS) &&
- (*last_res != state.residue))
+ if (status == DMA_IN_PROGRESS && (*last_res != state.residue))
return 1;
else
return 0;
@@ -464,7 +463,7 @@ static irqreturn_t stm32_interrupt(int irq, void *ptr)
writel_relaxed(USART_ICR_RTOCF,
port->membase + ofs->icr);
- if ((sr & USART_SR_WUF) && (ofs->icr != UNDEF_REG))
+ if ((sr & USART_SR_WUF) && ofs->icr != UNDEF_REG)
writel_relaxed(USART_ICR_WUCF,
port->membase + ofs->icr);
@@ -620,7 +619,6 @@ static void stm32_stop_rx(struct uart_port *port)
stm32_clr_bits(port, ofs->cr1, stm32_port->cr1_irq);
if (stm32_port->cr3_irq)
stm32_clr_bits(port, ofs->cr3, stm32_port->cr3_irq);
-
}
/* Handle breaks - ignored by us */
@@ -724,7 +722,7 @@ static unsigned int stm32_get_databits(struct ktermios *termios)
}
static void stm32_set_termios(struct uart_port *port, struct ktermios *termios,
- struct ktermios *old)
+ struct ktermios *old)
{
struct stm32_port *stm32_port = to_stm32_port(port);
struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
@@ -923,7 +921,7 @@ stm32_verify_port(struct uart_port *port, struct serial_struct *ser)
}
static void stm32_pm(struct uart_port *port, unsigned int state,
- unsigned int oldstate)
+ unsigned int oldstate)
{
struct stm32_port *stm32port = container_of(port,
struct stm32_port, port);
@@ -973,18 +971,17 @@ static int stm32_init_port(struct stm32_port *stm32port,
struct resource *res;
int ret;
+ ret = platform_get_irq(pdev, 0);
+ if (ret <= 0)
+ return ret ? : -ENODEV;
+
port->iotype = UPIO_MEM;
port->flags = UPF_BOOT_AUTOCONF;
port->ops = &stm32_uart_ops;
port->dev = &pdev->dev;
port->fifosize = stm32port->info->cfg.fifosize;
port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_STM32_CONSOLE);
-
- ret = platform_get_irq(pdev, 0);
- if (ret <= 0)
- return ret ? : -ENODEV;
port->irq = ret;
-
port->rs485_config = stm32_config_rs485;
ret = stm32_init_rs485(port, pdev);
@@ -1101,8 +1098,8 @@ static int stm32_of_dma_rx_probe(struct stm32_port *stm32port,
return -ENODEV;
}
stm32port->rx_buf = dma_alloc_coherent(&pdev->dev, RX_BUF_L,
- &stm32port->rx_dma_buf,
- GFP_KERNEL);
+ &stm32port->rx_dma_buf,
+ GFP_KERNEL);
if (!stm32port->rx_buf) {
ret = -ENOMEM;
goto alloc_err;
@@ -1177,8 +1174,8 @@ static int stm32_of_dma_tx_probe(struct stm32_port *stm32port,
return -ENODEV;
}
stm32port->tx_buf = dma_alloc_coherent(&pdev->dev, TX_BUF_L,
- &stm32port->tx_dma_buf,
- GFP_KERNEL);
+ &stm32port->tx_dma_buf,
+ GFP_KERNEL);
if (!stm32port->tx_buf) {
ret = -ENOMEM;
goto alloc_err;
@@ -1322,7 +1319,6 @@ static int stm32_serial_remove(struct platform_device *pdev)
return err;
}
-
#ifdef CONFIG_SERIAL_STM32_CONSOLE
static void stm32_console_putchar(struct uart_port *port, int ch)
{
@@ -1335,7 +1331,8 @@ static void stm32_console_putchar(struct uart_port *port, int ch)
writel_relaxed(ch, port->membase + ofs->tdr);
}
-static void stm32_console_write(struct console *co, const char *s, unsigned cnt)
+static void stm32_console_write(struct console *co, const char *s,
+ unsigned int cnt)
{
struct uart_port *port = &stm32_ports[co->index].port;
struct stm32_port *stm32_port = to_stm32_port(port);
@@ -1388,7 +1385,7 @@ static int stm32_console_setup(struct console *co, char *options)
* this to be called during the uart port registration when the
* driver gets probed and the port should be mapped at that point.
*/
- if (stm32port->port.mapbase == 0 || stm32port->port.membase == NULL)
+ if (stm32port->port.mapbase == 0 || !stm32port->port.membase)
return -ENXIO;
if (options)
--
2.17.1
next prev parent reply other threads:[~2021-01-06 16:23 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-06 16:21 [PATCH 0/7] STM32 uart cleanup and improvements Erwan Le Ray
2021-01-06 16:21 ` [PATCH v2 1/8] serial: stm32: fix DMA initialization error handling Erwan Le Ray
2021-01-06 16:21 ` Erwan Le Ray [this message]
2021-01-11 9:58 ` [PATCH v2 2/8] serial: stm32: fix code cleaning warnings and checks Jiri Slaby
2021-01-12 10:02 ` Erwan LE RAY
2021-01-12 10:24 ` Greg Kroah-Hartman
2021-01-06 16:21 ` [PATCH v2 3/8] serial: stm32: add "_usart" prefix in functions name Erwan Le Ray
2021-01-06 16:21 ` [PATCH v2 4/8] serial: stm32: add author Erwan Le Ray
2021-01-11 9:59 ` Jiri Slaby
2021-01-06 16:22 ` [PATCH v2 5/8] dt-bindings: serial: stm32: update rts-gpios and cts-gpios Erwan Le Ray
2021-01-06 16:22 ` [PATCH v2 6/8] serial: stm32: update conflicting RTS/CTS config comment Erwan Le Ray
2021-01-06 16:22 ` [PATCH v2 7/8] serial: stm32: clean probe and remove port deinit Erwan Le Ray
2021-01-06 16:22 ` [PATCH v2 8/8] serial: stm32: update transmission complete error message in shutdown Erwan Le Ray
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210106162203.28854-3-erwan.leray@foss.st.com \
--to=erwan.leray@foss.st.com \
--cc=alexandre.torgue@foss.st.com \
--cc=devicetree@vger.kernel.org \
--cc=fabrice.gasnier@foss.st.com \
--cc=gregkh@linuxfoundation.org \
--cc=jslaby@suse.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=robh+dt@kernel.org \
--cc=valentin.caron@foss.st.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).