From: Konrad Dybcio <konrad.dybcio@somainline.org>
To: phone-devel@vger.kernel.org
Cc: ~postmarketos/upstreaming@lists.sr.ht,
Konrad Dybcio <konrad.dybcio@somainline.org>,
Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Gustave Monce <gustave.monce@outlook.com>
Subject: [PATCH 09/18] arm64: dts: qcom: msm8994-octagon: Add QCA6174 bluetooth
Date: Sun, 31 Jan 2021 02:38:40 +0100 [thread overview]
Message-ID: <20210131013853.55810-10-konrad.dybcio@somainline.org> (raw)
In-Reply-To: <20210131013853.55810-1-konrad.dybcio@somainline.org>
From: Gustave Monce <gustave.monce@outlook.com>
Configure and enable QCA6174 Bluetooth and required pins.
Signed-off-by: Gustave Monce <gustave.monce@outlook.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
.../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 44 +++++++++++++++++++
1 file changed, 44 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi
index b8d89d64e2f1..78443f5a3881 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi
@@ -45,6 +45,21 @@ chosen {
ranges;
};
+ clocks {
+ compatible = "simple-bus";
+
+ divclk4: divclk4 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+
+ clock-frequency = <32768>;
+ clock-output-names = "divclk4";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&divclk4_pin_a>;
+ };
+ };
+
gpio-keys {
compatible = "gpio-keys";
input-name = "gpio-keys";
@@ -291,6 +306,35 @@ &blsp1_uart2 {
&blsp2_uart2 {
status = "okay";
+
+ qca6174_bt: bluetooth {
+ compatible = "qcom,qca6174-bt";
+
+ enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
+ clocks = <&divclk4>;
+ };
+};
+
+&pm8994_gpios {
+ bt_en_gpios: bt_en_gpios {
+ pinconf {
+ pins = "gpio19";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-low;
+ power-source = <PM8994_GPIO_S4>;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ bias-pull-down;
+ };
+ };
+
+ divclk4_pin_a: divclk4 {
+ pinconf {
+ pins = "gpio18";
+ function = PMIC_GPIO_FUNC_FUNC2;
+ power-source = <PM8994_GPIO_S4>;
+ bias-disable;
+ };
+ };
};
&pmi8994_spmi_regulators {
--
2.30.0
next prev parent reply other threads:[~2021-01-31 1:45 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-31 1:38 [PATCH 00/18] 8992/4/Lumia 950/XL DTS updates Konrad Dybcio
2021-01-31 1:38 ` [PATCH 01/18] arm64: dts: qcom: msm8994: Add SMP2P nodes Konrad Dybcio
2021-01-31 1:38 ` [PATCH 02/18] arm64: dts: qcom: msm8994: Fix remaining BLSP errors/mistakes Konrad Dybcio
2021-01-31 1:38 ` [PATCH 03/18] arm64: dts: qcom: msm8994: Sort hwlock properly Konrad Dybcio
2021-01-31 1:38 ` [PATCH 04/18] arm64: dts: qcom: msm8992: Make the DT an overlay on top of 8994 Konrad Dybcio
2021-01-31 1:38 ` [PATCH 05/18] arm64: dts: qcom: msm8992/4-lumia*: Create a common DTS Konrad Dybcio
2021-01-31 1:38 ` [PATCH 06/18] arm64: dts: qcom: msm8994-octagon: Fix up the memory map Konrad Dybcio
2021-01-31 1:38 ` [PATCH 07/18] arm64: dts: qcom: msm8994-octagon: Add gpio-keys and Hall sensor Konrad Dybcio
2021-01-31 1:38 ` [PATCH 08/18] arm64: dts: qcom: msm8994-octagon: Configure regulators Konrad Dybcio
2021-01-31 1:38 ` Konrad Dybcio [this message]
2021-01-31 1:38 ` [PATCH 10/18] arm64: dts: qcom: msm8994-octagon: Configure HD3SS460 Type-C mux pins Konrad Dybcio
2021-01-31 1:38 ` [PATCH 11/18] arm64: dts: qcom: msm8994-octagon: Add uSD card and disable HS400 on eMMC Konrad Dybcio
2021-02-18 13:41 ` Pavel Machek
2021-01-31 1:38 ` [PATCH 12/18] arm64: dts: qcom: msm8994-octagon: Configure Lattice iCE40 FPGA Konrad Dybcio
2021-02-18 13:43 ` Pavel Machek
2021-01-31 1:38 ` [PATCH 13/18] arm64: dts: qcom: msm8994-octagon: Configure PON keys Konrad Dybcio
2021-01-31 1:38 ` [PATCH 14/18] arm64: dts: qcom: msm8994-octagon: Add FM Radio and DDR regulator nodes Konrad Dybcio
2021-01-31 1:38 ` [PATCH 15/18] arm64: dts: qcom: msm8994-octagon: Add NXP NFC node Konrad Dybcio
2021-01-31 1:38 ` [PATCH 16/18] arm64: dts: qcom: msm8994-octagon: Add sensors on blsp1_i2c5 Konrad Dybcio
2021-01-31 1:38 ` [PATCH 17/18] arm64: dts: qcom: msm8994-octagon: Add TAS2553 codec Konrad Dybcio
2021-01-31 1:38 ` [PATCH 18/18] arm64: dts: qcom: msm8994-octagon: Add AD7147 and APDS9930 sensors Konrad Dybcio
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210131013853.55810-10-konrad.dybcio@somainline.org \
--to=konrad.dybcio@somainline.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=gustave.monce@outlook.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=phone-devel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=~postmarketos/upstreaming@lists.sr.ht \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).