* [PATCH v3] usb: typec: tcpm: Wait for vbus discharge to VSAFE0V before toggling
@ 2021-02-25 10:11 Badhri Jagan Sridharan
2021-02-25 19:55 ` Guenter Roeck
2021-03-01 15:19 ` Heikki Krogerus
0 siblings, 2 replies; 3+ messages in thread
From: Badhri Jagan Sridharan @ 2021-02-25 10:11 UTC (permalink / raw)
To: Guenter Roeck, Heikki Krogerus, Greg Kroah-Hartman
Cc: linux-usb, linux-kernel, Kyle Tso, stable, Badhri Jagan Sridharan
When vbus auto discharge is enabled, TCPM can sometimes be faster than
the TCPC i.e. TCPM can go ahead and move the port to unattached state
(involves disabling vbus auto discharge) before TCPC could effectively
discharge vbus to VSAFE0V. This leaves vbus with residual charge and
increases the decay time which prevents tsafe0v from being met.
This change makes TCPM waits for a maximum of tSafe0V(max) for vbus
to discharge to VSAFE0V before transitioning to unattached state
and re-enable toggling. If vbus discharges to vsafe0v sooner, then,
transition to unattached state
happens right away.
Also, while in SNK_READY, when auto discharge is enabled, drive
disconnect based on vbus turning off instead of Rp disappearing on
CC pins. Rp disappearing on CC pins is almost instanteous compared
to vbus decay.
Sink detach:
[ 541.703058] CC1: 3 -> 0, CC2: 0 -> 0 [state SNK_READY, polarity 0, disconnected]
[ 541.703331] Setting voltage/current limit 5000 mV 0 mA
[ 541.727235] VBUS on
[ 541.749650] VBUS off
[ 541.749653] pending state change SNK_READY -> SNK_UNATTACHED @ 650 ms [rev3 NONE_AMS]
[ 541.749944] VBUS VSAFE0V
[ 541.749945] state change SNK_READY -> SNK_UNATTACHED [rev3 NONE_AMS]
[ 541.750806] Disable vbus discharge ret:0
[ 541.907345] Start toggling
[ 541.922799] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
Source detach:
[ 2555.310414] state change SRC_SEND_CAPABILITIES -> SRC_READY [rev3 POWER_NEGOTIATION]
[ 2555.310675] AMS POWER_NEGOTIATION finished
[ 2555.310679] cc:=3
[ 2593.645886] CC1: 0 -> 0, CC2: 2 -> 0 [state SRC_READY, polarity 1, disconnected]
[ 2593.645919] pending state change SRC_READY -> SNK_UNATTACHED @ 650 ms [rev3 NONE_AMS]
[ 2593.648419] VBUS off
[ 2593.648960] VBUS VSAFE0V
[ 2593.648965] state change SRC_READY -> SNK_UNATTACHED [rev3 NONE_AMS]
[ 2593.649962] Disable vbus discharge ret:0
[ 2593.890322] Start toggling
[ 2593.925663] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0,
Fixes: f321a02caebd ("usb: typec: tcpm: Implement enabling Auto
Discharge disconnect support")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
---
Changes since V1:
- Add Fixes tag
Changes since V2:
- Remove VBUS_DISCHARGE state as preferred by Guenter Roeck
---
drivers/usb/typec/tcpm/tcpm.c | 75 ++++++++++++++++++++++++++++++-----
1 file changed, 65 insertions(+), 10 deletions(-)
diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
index be0b6469dd3d..8469c37a59e1 100644
--- a/drivers/usb/typec/tcpm/tcpm.c
+++ b/drivers/usb/typec/tcpm/tcpm.c
@@ -438,6 +438,9 @@ struct tcpm_port {
enum tcpm_ams next_ams;
bool in_ams;
+ /* Auto vbus discharge status */
+ bool auto_vbus_discharge_enabled;
+
#ifdef CONFIG_DEBUG_FS
struct dentry *dentry;
struct mutex logbuffer_lock; /* log buffer access lock */
@@ -507,6 +510,9 @@ static const char * const pd_rev[] = {
(tcpm_port_is_sink(port) && \
((port)->cc1 == TYPEC_CC_RP_3_0 || (port)->cc2 == TYPEC_CC_RP_3_0))
+#define tcpm_wait_for_discharge(port) \
+ (((port)->auto_vbus_discharge_enabled && !(port)->vbus_vsafe0v) ? PD_T_SAFE_0V : 0)
+
static enum tcpm_state tcpm_default_state(struct tcpm_port *port)
{
if (port->port_type == TYPEC_PORT_DRP) {
@@ -3413,6 +3419,8 @@ static int tcpm_src_attach(struct tcpm_port *port)
if (port->tcpc->enable_auto_vbus_discharge) {
ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, true);
tcpm_log_force(port, "enable vbus discharge ret:%d", ret);
+ if (!ret)
+ port->auto_vbus_discharge_enabled = true;
}
ret = tcpm_set_roles(port, true, TYPEC_SOURCE, tcpm_data_role_for_source(port));
@@ -3495,6 +3503,8 @@ static void tcpm_reset_port(struct tcpm_port *port)
if (port->tcpc->enable_auto_vbus_discharge) {
ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, false);
tcpm_log_force(port, "Disable vbus discharge ret:%d", ret);
+ if (!ret)
+ port->auto_vbus_discharge_enabled = false;
}
port->in_ams = false;
port->ams = NONE_AMS;
@@ -3568,6 +3578,8 @@ static int tcpm_snk_attach(struct tcpm_port *port)
tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_USB, false, VSAFE5V);
ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, true);
tcpm_log_force(port, "enable vbus discharge ret:%d", ret);
+ if (!ret)
+ port->auto_vbus_discharge_enabled = true;
}
ret = tcpm_set_roles(port, true, TYPEC_SINK, tcpm_data_role_for_sink(port));
@@ -4670,9 +4682,9 @@ static void _tcpm_cc_change(struct tcpm_port *port, enum typec_cc_status cc1,
if (tcpm_port_is_disconnected(port) ||
!tcpm_port_is_source(port)) {
if (port->port_type == TYPEC_PORT_SRC)
- tcpm_set_state(port, SRC_UNATTACHED, 0);
+ tcpm_set_state(port, SRC_UNATTACHED, tcpm_wait_for_discharge(port));
else
- tcpm_set_state(port, SNK_UNATTACHED, 0);
+ tcpm_set_state(port, SNK_UNATTACHED, tcpm_wait_for_discharge(port));
}
break;
case SNK_UNATTACHED:
@@ -4703,7 +4715,23 @@ static void _tcpm_cc_change(struct tcpm_port *port, enum typec_cc_status cc1,
tcpm_set_state(port, SNK_DEBOUNCED, 0);
break;
case SNK_READY:
- if (tcpm_port_is_disconnected(port))
+ /*
+ * EXIT condition is based primarily on vbus disconnect and CC is secondary.
+ * "A port that has entered into USB PD communications with the Source and
+ * has seen the CC voltage exceed vRd-USB may monitor the CC pin to detect
+ * cable disconnect in addition to monitoring VBUS.
+ *
+ * A port that is monitoring the CC voltage for disconnect (but is not in
+ * the process of a USB PD PR_Swap or USB PD FR_Swap) shall transition to
+ * Unattached.SNK within tSinkDisconnect after the CC voltage remains below
+ * vRd-USB for tPDDebounce."
+ *
+ * When set_auto_vbus_discharge_threshold is enabled, CC pins go
+ * away before vbus decays to disconnect threshold. Allow
+ * disconnect to be driven by vbus disconnect when auto vbus
+ * discharge is enabled.
+ */
+ if (!port->auto_vbus_discharge_enabled && tcpm_port_is_disconnected(port))
tcpm_set_state(port, unattached_state(port), 0);
else if (!port->pd_capable &&
(cc1 != old_cc1 || cc2 != old_cc2))
@@ -4802,9 +4830,13 @@ static void _tcpm_cc_change(struct tcpm_port *port, enum typec_cc_status cc1,
* Ignore CC changes here.
*/
break;
-
default:
- if (tcpm_port_is_disconnected(port))
+ /*
+ * While acting as sink and auto vbus discharge is enabled, Allow disconnect
+ * to be driven by vbus disconnect.
+ */
+ if (tcpm_port_is_disconnected(port) && !(port->pwr_role == TYPEC_SINK &&
+ port->auto_vbus_discharge_enabled))
tcpm_set_state(port, unattached_state(port), 0);
break;
}
@@ -4968,8 +5000,16 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
case SRC_TRANSITION_SUPPLY:
case SRC_READY:
case SRC_WAIT_NEW_CAPABILITIES:
- /* Force to unattached state to re-initiate connection */
- tcpm_set_state(port, SRC_UNATTACHED, 0);
+ /*
+ * Force to unattached state to re-initiate connection.
+ * DRP port should move to Unattached.SNK instead of Unattached.SRC if
+ * sink removed. Although sink removal here is due to source's vbus collapse,
+ * treat it the same way for consistency.
+ */
+ if (port->port_type == TYPEC_PORT_SRC)
+ tcpm_set_state(port, SRC_UNATTACHED, tcpm_wait_for_discharge(port));
+ else
+ tcpm_set_state(port, SNK_UNATTACHED, tcpm_wait_for_discharge(port));
break;
case PORT_RESET:
@@ -4988,9 +5028,8 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
break;
default:
- if (port->pwr_role == TYPEC_SINK &&
- port->attached)
- tcpm_set_state(port, SNK_UNATTACHED, 0);
+ if (port->pwr_role == TYPEC_SINK && port->attached)
+ tcpm_set_state(port, SNK_UNATTACHED, tcpm_wait_for_discharge(port));
break;
}
}
@@ -5012,7 +5051,23 @@ static void _tcpm_pd_vbus_vsafe0v(struct tcpm_port *port)
tcpm_set_state(port, tcpm_try_snk(port) ? SNK_TRY : SRC_ATTACHED,
PD_T_CC_DEBOUNCE);
break;
+ case SRC_STARTUP:
+ case SRC_SEND_CAPABILITIES:
+ case SRC_SEND_CAPABILITIES_TIMEOUT:
+ case SRC_NEGOTIATE_CAPABILITIES:
+ case SRC_TRANSITION_SUPPLY:
+ case SRC_READY:
+ case SRC_WAIT_NEW_CAPABILITIES:
+ if (port->auto_vbus_discharge_enabled) {
+ if (port->port_type == TYPEC_PORT_SRC)
+ tcpm_set_state(port, SRC_UNATTACHED, 0);
+ else
+ tcpm_set_state(port, SNK_UNATTACHED, 0);
+ }
+ break;
default:
+ if (port->pwr_role == TYPEC_SINK && port->auto_vbus_discharge_enabled)
+ tcpm_set_state(port, SNK_UNATTACHED, 0);
break;
}
}
--
2.30.0.617.g56c4b15f3c-goog
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v3] usb: typec: tcpm: Wait for vbus discharge to VSAFE0V before toggling
2021-02-25 10:11 [PATCH v3] usb: typec: tcpm: Wait for vbus discharge to VSAFE0V before toggling Badhri Jagan Sridharan
@ 2021-02-25 19:55 ` Guenter Roeck
2021-03-01 15:19 ` Heikki Krogerus
1 sibling, 0 replies; 3+ messages in thread
From: Guenter Roeck @ 2021-02-25 19:55 UTC (permalink / raw)
To: Badhri Jagan Sridharan
Cc: Heikki Krogerus, Greg Kroah-Hartman, linux-usb, linux-kernel,
Kyle Tso, stable
On Thu, Feb 25, 2021 at 02:11:04AM -0800, Badhri Jagan Sridharan wrote:
> When vbus auto discharge is enabled, TCPM can sometimes be faster than
> the TCPC i.e. TCPM can go ahead and move the port to unattached state
> (involves disabling vbus auto discharge) before TCPC could effectively
> discharge vbus to VSAFE0V. This leaves vbus with residual charge and
> increases the decay time which prevents tsafe0v from being met.
> This change makes TCPM waits for a maximum of tSafe0V(max) for vbus
> to discharge to VSAFE0V before transitioning to unattached state
> and re-enable toggling. If vbus discharges to vsafe0v sooner, then,
> transition to unattached state
> happens right away.
>
> Also, while in SNK_READY, when auto discharge is enabled, drive
> disconnect based on vbus turning off instead of Rp disappearing on
> CC pins. Rp disappearing on CC pins is almost instanteous compared
> to vbus decay.
>
> Sink detach:
> [ 541.703058] CC1: 3 -> 0, CC2: 0 -> 0 [state SNK_READY, polarity 0, disconnected]
> [ 541.703331] Setting voltage/current limit 5000 mV 0 mA
> [ 541.727235] VBUS on
> [ 541.749650] VBUS off
> [ 541.749653] pending state change SNK_READY -> SNK_UNATTACHED @ 650 ms [rev3 NONE_AMS]
> [ 541.749944] VBUS VSAFE0V
> [ 541.749945] state change SNK_READY -> SNK_UNATTACHED [rev3 NONE_AMS]
> [ 541.750806] Disable vbus discharge ret:0
> [ 541.907345] Start toggling
> [ 541.922799] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
>
> Source detach:
> [ 2555.310414] state change SRC_SEND_CAPABILITIES -> SRC_READY [rev3 POWER_NEGOTIATION]
> [ 2555.310675] AMS POWER_NEGOTIATION finished
> [ 2555.310679] cc:=3
> [ 2593.645886] CC1: 0 -> 0, CC2: 2 -> 0 [state SRC_READY, polarity 1, disconnected]
> [ 2593.645919] pending state change SRC_READY -> SNK_UNATTACHED @ 650 ms [rev3 NONE_AMS]
> [ 2593.648419] VBUS off
> [ 2593.648960] VBUS VSAFE0V
> [ 2593.648965] state change SRC_READY -> SNK_UNATTACHED [rev3 NONE_AMS]
> [ 2593.649962] Disable vbus discharge ret:0
> [ 2593.890322] Start toggling
> [ 2593.925663] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0,
>
> Fixes: f321a02caebd ("usb: typec: tcpm: Implement enabling Auto
> Discharge disconnect support")
> Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Guenter
> ---
> Changes since V1:
> - Add Fixes tag
>
> Changes since V2:
> - Remove VBUS_DISCHARGE state as preferred by Guenter Roeck
> ---
> drivers/usb/typec/tcpm/tcpm.c | 75 ++++++++++++++++++++++++++++++-----
> 1 file changed, 65 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
> index be0b6469dd3d..8469c37a59e1 100644
> --- a/drivers/usb/typec/tcpm/tcpm.c
> +++ b/drivers/usb/typec/tcpm/tcpm.c
> @@ -438,6 +438,9 @@ struct tcpm_port {
> enum tcpm_ams next_ams;
> bool in_ams;
>
> + /* Auto vbus discharge status */
> + bool auto_vbus_discharge_enabled;
> +
> #ifdef CONFIG_DEBUG_FS
> struct dentry *dentry;
> struct mutex logbuffer_lock; /* log buffer access lock */
> @@ -507,6 +510,9 @@ static const char * const pd_rev[] = {
> (tcpm_port_is_sink(port) && \
> ((port)->cc1 == TYPEC_CC_RP_3_0 || (port)->cc2 == TYPEC_CC_RP_3_0))
>
> +#define tcpm_wait_for_discharge(port) \
> + (((port)->auto_vbus_discharge_enabled && !(port)->vbus_vsafe0v) ? PD_T_SAFE_0V : 0)
> +
> static enum tcpm_state tcpm_default_state(struct tcpm_port *port)
> {
> if (port->port_type == TYPEC_PORT_DRP) {
> @@ -3413,6 +3419,8 @@ static int tcpm_src_attach(struct tcpm_port *port)
> if (port->tcpc->enable_auto_vbus_discharge) {
> ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, true);
> tcpm_log_force(port, "enable vbus discharge ret:%d", ret);
> + if (!ret)
> + port->auto_vbus_discharge_enabled = true;
> }
>
> ret = tcpm_set_roles(port, true, TYPEC_SOURCE, tcpm_data_role_for_source(port));
> @@ -3495,6 +3503,8 @@ static void tcpm_reset_port(struct tcpm_port *port)
> if (port->tcpc->enable_auto_vbus_discharge) {
> ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, false);
> tcpm_log_force(port, "Disable vbus discharge ret:%d", ret);
> + if (!ret)
> + port->auto_vbus_discharge_enabled = false;
> }
> port->in_ams = false;
> port->ams = NONE_AMS;
> @@ -3568,6 +3578,8 @@ static int tcpm_snk_attach(struct tcpm_port *port)
> tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_USB, false, VSAFE5V);
> ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, true);
> tcpm_log_force(port, "enable vbus discharge ret:%d", ret);
> + if (!ret)
> + port->auto_vbus_discharge_enabled = true;
> }
>
> ret = tcpm_set_roles(port, true, TYPEC_SINK, tcpm_data_role_for_sink(port));
> @@ -4670,9 +4682,9 @@ static void _tcpm_cc_change(struct tcpm_port *port, enum typec_cc_status cc1,
> if (tcpm_port_is_disconnected(port) ||
> !tcpm_port_is_source(port)) {
> if (port->port_type == TYPEC_PORT_SRC)
> - tcpm_set_state(port, SRC_UNATTACHED, 0);
> + tcpm_set_state(port, SRC_UNATTACHED, tcpm_wait_for_discharge(port));
> else
> - tcpm_set_state(port, SNK_UNATTACHED, 0);
> + tcpm_set_state(port, SNK_UNATTACHED, tcpm_wait_for_discharge(port));
> }
> break;
> case SNK_UNATTACHED:
> @@ -4703,7 +4715,23 @@ static void _tcpm_cc_change(struct tcpm_port *port, enum typec_cc_status cc1,
> tcpm_set_state(port, SNK_DEBOUNCED, 0);
> break;
> case SNK_READY:
> - if (tcpm_port_is_disconnected(port))
> + /*
> + * EXIT condition is based primarily on vbus disconnect and CC is secondary.
> + * "A port that has entered into USB PD communications with the Source and
> + * has seen the CC voltage exceed vRd-USB may monitor the CC pin to detect
> + * cable disconnect in addition to monitoring VBUS.
> + *
> + * A port that is monitoring the CC voltage for disconnect (but is not in
> + * the process of a USB PD PR_Swap or USB PD FR_Swap) shall transition to
> + * Unattached.SNK within tSinkDisconnect after the CC voltage remains below
> + * vRd-USB for tPDDebounce."
> + *
> + * When set_auto_vbus_discharge_threshold is enabled, CC pins go
> + * away before vbus decays to disconnect threshold. Allow
> + * disconnect to be driven by vbus disconnect when auto vbus
> + * discharge is enabled.
> + */
> + if (!port->auto_vbus_discharge_enabled && tcpm_port_is_disconnected(port))
> tcpm_set_state(port, unattached_state(port), 0);
> else if (!port->pd_capable &&
> (cc1 != old_cc1 || cc2 != old_cc2))
> @@ -4802,9 +4830,13 @@ static void _tcpm_cc_change(struct tcpm_port *port, enum typec_cc_status cc1,
> * Ignore CC changes here.
> */
> break;
> -
> default:
> - if (tcpm_port_is_disconnected(port))
> + /*
> + * While acting as sink and auto vbus discharge is enabled, Allow disconnect
> + * to be driven by vbus disconnect.
> + */
> + if (tcpm_port_is_disconnected(port) && !(port->pwr_role == TYPEC_SINK &&
> + port->auto_vbus_discharge_enabled))
> tcpm_set_state(port, unattached_state(port), 0);
> break;
> }
> @@ -4968,8 +5000,16 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
> case SRC_TRANSITION_SUPPLY:
> case SRC_READY:
> case SRC_WAIT_NEW_CAPABILITIES:
> - /* Force to unattached state to re-initiate connection */
> - tcpm_set_state(port, SRC_UNATTACHED, 0);
> + /*
> + * Force to unattached state to re-initiate connection.
> + * DRP port should move to Unattached.SNK instead of Unattached.SRC if
> + * sink removed. Although sink removal here is due to source's vbus collapse,
> + * treat it the same way for consistency.
> + */
> + if (port->port_type == TYPEC_PORT_SRC)
> + tcpm_set_state(port, SRC_UNATTACHED, tcpm_wait_for_discharge(port));
> + else
> + tcpm_set_state(port, SNK_UNATTACHED, tcpm_wait_for_discharge(port));
> break;
>
> case PORT_RESET:
> @@ -4988,9 +5028,8 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
> break;
>
> default:
> - if (port->pwr_role == TYPEC_SINK &&
> - port->attached)
> - tcpm_set_state(port, SNK_UNATTACHED, 0);
> + if (port->pwr_role == TYPEC_SINK && port->attached)
> + tcpm_set_state(port, SNK_UNATTACHED, tcpm_wait_for_discharge(port));
> break;
> }
> }
> @@ -5012,7 +5051,23 @@ static void _tcpm_pd_vbus_vsafe0v(struct tcpm_port *port)
> tcpm_set_state(port, tcpm_try_snk(port) ? SNK_TRY : SRC_ATTACHED,
> PD_T_CC_DEBOUNCE);
> break;
> + case SRC_STARTUP:
> + case SRC_SEND_CAPABILITIES:
> + case SRC_SEND_CAPABILITIES_TIMEOUT:
> + case SRC_NEGOTIATE_CAPABILITIES:
> + case SRC_TRANSITION_SUPPLY:
> + case SRC_READY:
> + case SRC_WAIT_NEW_CAPABILITIES:
> + if (port->auto_vbus_discharge_enabled) {
> + if (port->port_type == TYPEC_PORT_SRC)
> + tcpm_set_state(port, SRC_UNATTACHED, 0);
> + else
> + tcpm_set_state(port, SNK_UNATTACHED, 0);
> + }
> + break;
> default:
> + if (port->pwr_role == TYPEC_SINK && port->auto_vbus_discharge_enabled)
> + tcpm_set_state(port, SNK_UNATTACHED, 0);
> break;
> }
> }
> --
> 2.30.0.617.g56c4b15f3c-goog
>
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v3] usb: typec: tcpm: Wait for vbus discharge to VSAFE0V before toggling
2021-02-25 10:11 [PATCH v3] usb: typec: tcpm: Wait for vbus discharge to VSAFE0V before toggling Badhri Jagan Sridharan
2021-02-25 19:55 ` Guenter Roeck
@ 2021-03-01 15:19 ` Heikki Krogerus
1 sibling, 0 replies; 3+ messages in thread
From: Heikki Krogerus @ 2021-03-01 15:19 UTC (permalink / raw)
To: Badhri Jagan Sridharan
Cc: Guenter Roeck, Greg Kroah-Hartman, linux-usb, linux-kernel,
Kyle Tso, stable
On Thu, Feb 25, 2021 at 02:11:04AM -0800, Badhri Jagan Sridharan wrote:
> When vbus auto discharge is enabled, TCPM can sometimes be faster than
> the TCPC i.e. TCPM can go ahead and move the port to unattached state
> (involves disabling vbus auto discharge) before TCPC could effectively
> discharge vbus to VSAFE0V. This leaves vbus with residual charge and
> increases the decay time which prevents tsafe0v from being met.
> This change makes TCPM waits for a maximum of tSafe0V(max) for vbus
> to discharge to VSAFE0V before transitioning to unattached state
> and re-enable toggling. If vbus discharges to vsafe0v sooner, then,
> transition to unattached state
> happens right away.
>
> Also, while in SNK_READY, when auto discharge is enabled, drive
> disconnect based on vbus turning off instead of Rp disappearing on
> CC pins. Rp disappearing on CC pins is almost instanteous compared
> to vbus decay.
>
> Sink detach:
> [ 541.703058] CC1: 3 -> 0, CC2: 0 -> 0 [state SNK_READY, polarity 0, disconnected]
> [ 541.703331] Setting voltage/current limit 5000 mV 0 mA
> [ 541.727235] VBUS on
> [ 541.749650] VBUS off
> [ 541.749653] pending state change SNK_READY -> SNK_UNATTACHED @ 650 ms [rev3 NONE_AMS]
> [ 541.749944] VBUS VSAFE0V
> [ 541.749945] state change SNK_READY -> SNK_UNATTACHED [rev3 NONE_AMS]
> [ 541.750806] Disable vbus discharge ret:0
> [ 541.907345] Start toggling
> [ 541.922799] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
>
> Source detach:
> [ 2555.310414] state change SRC_SEND_CAPABILITIES -> SRC_READY [rev3 POWER_NEGOTIATION]
> [ 2555.310675] AMS POWER_NEGOTIATION finished
> [ 2555.310679] cc:=3
> [ 2593.645886] CC1: 0 -> 0, CC2: 2 -> 0 [state SRC_READY, polarity 1, disconnected]
> [ 2593.645919] pending state change SRC_READY -> SNK_UNATTACHED @ 650 ms [rev3 NONE_AMS]
> [ 2593.648419] VBUS off
> [ 2593.648960] VBUS VSAFE0V
> [ 2593.648965] state change SRC_READY -> SNK_UNATTACHED [rev3 NONE_AMS]
> [ 2593.649962] Disable vbus discharge ret:0
> [ 2593.890322] Start toggling
> [ 2593.925663] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0,
>
> Fixes: f321a02caebd ("usb: typec: tcpm: Implement enabling Auto
> Discharge disconnect support")
> Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
> ---
> Changes since V1:
> - Add Fixes tag
>
> Changes since V2:
> - Remove VBUS_DISCHARGE state as preferred by Guenter Roeck
> ---
> drivers/usb/typec/tcpm/tcpm.c | 75 ++++++++++++++++++++++++++++++-----
> 1 file changed, 65 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
> index be0b6469dd3d..8469c37a59e1 100644
> --- a/drivers/usb/typec/tcpm/tcpm.c
> +++ b/drivers/usb/typec/tcpm/tcpm.c
> @@ -438,6 +438,9 @@ struct tcpm_port {
> enum tcpm_ams next_ams;
> bool in_ams;
>
> + /* Auto vbus discharge status */
> + bool auto_vbus_discharge_enabled;
> +
> #ifdef CONFIG_DEBUG_FS
> struct dentry *dentry;
> struct mutex logbuffer_lock; /* log buffer access lock */
> @@ -507,6 +510,9 @@ static const char * const pd_rev[] = {
> (tcpm_port_is_sink(port) && \
> ((port)->cc1 == TYPEC_CC_RP_3_0 || (port)->cc2 == TYPEC_CC_RP_3_0))
>
> +#define tcpm_wait_for_discharge(port) \
> + (((port)->auto_vbus_discharge_enabled && !(port)->vbus_vsafe0v) ? PD_T_SAFE_0V : 0)
> +
> static enum tcpm_state tcpm_default_state(struct tcpm_port *port)
> {
> if (port->port_type == TYPEC_PORT_DRP) {
> @@ -3413,6 +3419,8 @@ static int tcpm_src_attach(struct tcpm_port *port)
> if (port->tcpc->enable_auto_vbus_discharge) {
> ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, true);
> tcpm_log_force(port, "enable vbus discharge ret:%d", ret);
> + if (!ret)
> + port->auto_vbus_discharge_enabled = true;
> }
>
> ret = tcpm_set_roles(port, true, TYPEC_SOURCE, tcpm_data_role_for_source(port));
> @@ -3495,6 +3503,8 @@ static void tcpm_reset_port(struct tcpm_port *port)
> if (port->tcpc->enable_auto_vbus_discharge) {
> ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, false);
> tcpm_log_force(port, "Disable vbus discharge ret:%d", ret);
> + if (!ret)
> + port->auto_vbus_discharge_enabled = false;
> }
> port->in_ams = false;
> port->ams = NONE_AMS;
> @@ -3568,6 +3578,8 @@ static int tcpm_snk_attach(struct tcpm_port *port)
> tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_USB, false, VSAFE5V);
> ret = port->tcpc->enable_auto_vbus_discharge(port->tcpc, true);
> tcpm_log_force(port, "enable vbus discharge ret:%d", ret);
> + if (!ret)
> + port->auto_vbus_discharge_enabled = true;
> }
>
> ret = tcpm_set_roles(port, true, TYPEC_SINK, tcpm_data_role_for_sink(port));
> @@ -4670,9 +4682,9 @@ static void _tcpm_cc_change(struct tcpm_port *port, enum typec_cc_status cc1,
> if (tcpm_port_is_disconnected(port) ||
> !tcpm_port_is_source(port)) {
> if (port->port_type == TYPEC_PORT_SRC)
> - tcpm_set_state(port, SRC_UNATTACHED, 0);
> + tcpm_set_state(port, SRC_UNATTACHED, tcpm_wait_for_discharge(port));
> else
> - tcpm_set_state(port, SNK_UNATTACHED, 0);
> + tcpm_set_state(port, SNK_UNATTACHED, tcpm_wait_for_discharge(port));
> }
> break;
> case SNK_UNATTACHED:
> @@ -4703,7 +4715,23 @@ static void _tcpm_cc_change(struct tcpm_port *port, enum typec_cc_status cc1,
> tcpm_set_state(port, SNK_DEBOUNCED, 0);
> break;
> case SNK_READY:
> - if (tcpm_port_is_disconnected(port))
> + /*
> + * EXIT condition is based primarily on vbus disconnect and CC is secondary.
> + * "A port that has entered into USB PD communications with the Source and
> + * has seen the CC voltage exceed vRd-USB may monitor the CC pin to detect
> + * cable disconnect in addition to monitoring VBUS.
> + *
> + * A port that is monitoring the CC voltage for disconnect (but is not in
> + * the process of a USB PD PR_Swap or USB PD FR_Swap) shall transition to
> + * Unattached.SNK within tSinkDisconnect after the CC voltage remains below
> + * vRd-USB for tPDDebounce."
> + *
> + * When set_auto_vbus_discharge_threshold is enabled, CC pins go
> + * away before vbus decays to disconnect threshold. Allow
> + * disconnect to be driven by vbus disconnect when auto vbus
> + * discharge is enabled.
> + */
> + if (!port->auto_vbus_discharge_enabled && tcpm_port_is_disconnected(port))
> tcpm_set_state(port, unattached_state(port), 0);
> else if (!port->pd_capable &&
> (cc1 != old_cc1 || cc2 != old_cc2))
> @@ -4802,9 +4830,13 @@ static void _tcpm_cc_change(struct tcpm_port *port, enum typec_cc_status cc1,
> * Ignore CC changes here.
> */
> break;
> -
> default:
> - if (tcpm_port_is_disconnected(port))
> + /*
> + * While acting as sink and auto vbus discharge is enabled, Allow disconnect
> + * to be driven by vbus disconnect.
> + */
> + if (tcpm_port_is_disconnected(port) && !(port->pwr_role == TYPEC_SINK &&
> + port->auto_vbus_discharge_enabled))
> tcpm_set_state(port, unattached_state(port), 0);
> break;
> }
> @@ -4968,8 +5000,16 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
> case SRC_TRANSITION_SUPPLY:
> case SRC_READY:
> case SRC_WAIT_NEW_CAPABILITIES:
> - /* Force to unattached state to re-initiate connection */
> - tcpm_set_state(port, SRC_UNATTACHED, 0);
> + /*
> + * Force to unattached state to re-initiate connection.
> + * DRP port should move to Unattached.SNK instead of Unattached.SRC if
> + * sink removed. Although sink removal here is due to source's vbus collapse,
> + * treat it the same way for consistency.
> + */
> + if (port->port_type == TYPEC_PORT_SRC)
> + tcpm_set_state(port, SRC_UNATTACHED, tcpm_wait_for_discharge(port));
> + else
> + tcpm_set_state(port, SNK_UNATTACHED, tcpm_wait_for_discharge(port));
> break;
>
> case PORT_RESET:
> @@ -4988,9 +5028,8 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
> break;
>
> default:
> - if (port->pwr_role == TYPEC_SINK &&
> - port->attached)
> - tcpm_set_state(port, SNK_UNATTACHED, 0);
> + if (port->pwr_role == TYPEC_SINK && port->attached)
> + tcpm_set_state(port, SNK_UNATTACHED, tcpm_wait_for_discharge(port));
> break;
> }
> }
> @@ -5012,7 +5051,23 @@ static void _tcpm_pd_vbus_vsafe0v(struct tcpm_port *port)
> tcpm_set_state(port, tcpm_try_snk(port) ? SNK_TRY : SRC_ATTACHED,
> PD_T_CC_DEBOUNCE);
> break;
> + case SRC_STARTUP:
> + case SRC_SEND_CAPABILITIES:
> + case SRC_SEND_CAPABILITIES_TIMEOUT:
> + case SRC_NEGOTIATE_CAPABILITIES:
> + case SRC_TRANSITION_SUPPLY:
> + case SRC_READY:
> + case SRC_WAIT_NEW_CAPABILITIES:
> + if (port->auto_vbus_discharge_enabled) {
> + if (port->port_type == TYPEC_PORT_SRC)
> + tcpm_set_state(port, SRC_UNATTACHED, 0);
> + else
> + tcpm_set_state(port, SNK_UNATTACHED, 0);
> + }
> + break;
> default:
> + if (port->pwr_role == TYPEC_SINK && port->auto_vbus_discharge_enabled)
> + tcpm_set_state(port, SNK_UNATTACHED, 0);
> break;
> }
> }
> --
> 2.30.0.617.g56c4b15f3c-goog
thanks,
--
heikki
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2021-03-01 15:22 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-02-25 10:11 [PATCH v3] usb: typec: tcpm: Wait for vbus discharge to VSAFE0V before toggling Badhri Jagan Sridharan
2021-02-25 19:55 ` Guenter Roeck
2021-03-01 15:19 ` Heikki Krogerus
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).