linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
To: linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>,
	Bartosz Golaszewski <bgolaszewski@baylibre.com>,
	Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
	Marek Vasut <marex@denx.de>,
	Roman Guskov <rguskov@dh-electronics.com>
Subject: [PATCH v1 1/1] gpiolib: Read "gpio-line-names" from a firmware node
Date: Fri,  5 Mar 2021 14:02:40 +0200	[thread overview]
Message-ID: <20210305120240.42830-1-andriy.shevchenko@linux.intel.com> (raw)

On STM32MP1, the GPIO banks are subnodes of pin-controller@50002000,
see arch/arm/boot/dts/stm32mp151.dtsi. The driver for
pin-controller@50002000 is in drivers/pinctrl/stm32/pinctrl-stm32.c
and iterates over all of its DT subnodes when registering each GPIO
bank gpiochip. Each gpiochip has:

  - gpio_chip.parent = dev,
    where dev is the device node of the pin controller
  - gpio_chip.of_node = np,
    which is the OF node of the GPIO bank

Therefore, dev_fwnode(chip->parent) != of_fwnode_handle(chip.of_node),
i.e. pin-controller@50002000 != pin-controller@50002000/gpio@5000*000.

The original code behaved correctly, as it extracted the "gpio-line-names"
from of_fwnode_handle(chip.of_node) = pin-controller@50002000/gpio@5000*000.

To achieve the same behaviour, read property from the firmware node.

Fixes: 7cba1a4d5e162 ("gpiolib: generalize devprop_gpiochip_set_names() for device properties")
Reported-by: Marek Vasut <marex@denx.de>
Reported-by: Roman Guskov <rguskov@dh-electronics.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
 drivers/gpio/gpiolib.c | 12 ++++--------
 1 file changed, 4 insertions(+), 8 deletions(-)

diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index 3bc25a9c4cd6..ba88011cc79d 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -367,22 +367,18 @@ static int gpiochip_set_desc_names(struct gpio_chip *gc)
  *
  * Looks for device property "gpio-line-names" and if it exists assigns
  * GPIO line names for the chip. The memory allocated for the assigned
- * names belong to the underlying software node and should not be released
+ * names belong to the underlying firmware node and should not be released
  * by the caller.
  */
 static int devprop_gpiochip_set_names(struct gpio_chip *chip)
 {
 	struct gpio_device *gdev = chip->gpiodev;
-	struct device *dev = chip->parent;
+	struct fwnode_handle *fwnode = dev_fwnode(&gdev->dev);
 	const char **names;
 	int ret, i;
 	int count;
 
-	/* GPIO chip may not have a parent device whose properties we inspect. */
-	if (!dev)
-		return 0;
-
-	count = device_property_string_array_count(dev, "gpio-line-names");
+	count = fwnode_property_string_array_count(fwnode, "gpio-line-names");
 	if (count < 0)
 		return 0;
 
@@ -396,7 +392,7 @@ static int devprop_gpiochip_set_names(struct gpio_chip *chip)
 	if (!names)
 		return -ENOMEM;
 
-	ret = device_property_read_string_array(dev, "gpio-line-names",
+	ret = fwnode_property_read_string_array(fwnode, "gpio-line-names",
 						names, count);
 	if (ret < 0) {
 		dev_warn(&gdev->dev, "failed to read GPIO line names\n");
-- 
2.30.1


             reply	other threads:[~2021-03-05 12:03 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-03-05 12:02 Andy Shevchenko [this message]
2021-03-05 12:11 ` [PATCH v1 1/1] gpiolib: Read "gpio-line-names" from a firmware node Marek Vasut
2021-03-05 12:24   ` Andy Shevchenko
2021-03-05 12:26     ` Marek Vasut
2021-03-07 13:55 ` Bartosz Golaszewski
2021-03-07 16:14   ` Andy Shevchenko
2021-03-08 11:45     ` Andy Shevchenko
2021-03-08 13:00       ` Bartosz Golaszewski
2021-03-15  9:01 ` Bartosz Golaszewski
2021-03-15 10:16   ` Andy Shevchenko
2021-03-15 12:50     ` Andy Shevchenko
2021-03-15 14:04       ` Bartosz Golaszewski
2021-03-15 14:34         ` Andy Shevchenko
2021-03-15 16:47           ` Bartosz Golaszewski
2021-03-15 17:04             ` Andy Shevchenko
2021-04-10  0:45               ` Marek Vasut
2021-04-10  9:06                 ` Bartosz Golaszewski
2021-04-10 13:18                   ` Marek Vasut

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210305120240.42830-1-andriy.shevchenko@linux.intel.com \
    --to=andriy.shevchenko@linux.intel.com \
    --cc=bgolaszewski@baylibre.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=marex@denx.de \
    --cc=rguskov@dh-electronics.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).