[PATCH v2 4/7] ARM: imx6q: remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs

[Oleksij Rempel <o.rempel@pengutronix.de>]

This configuration should be set over device tree.

If this patch breaks network functionality on your system, enable the
AT803X_PHY driver and set following device tree property in the PHY
node:

    qca,clk-out-frequency = <125000000>;

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 arch/arm/boot/dts/imx6dl-riotboard.dts |  2 ++
 arch/arm/mach-imx/mach-imx6q.c         | 30 --------------------------
 2 files changed, 2 insertions(+), 30 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/imx6dl-riotboard.dts
index 065d3ab0f50a..e7d9bfbfd0e4 100644
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
@@ -106,6 +106,8 @@ rgmii_phy: ethernet-phy@4 {
 			reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10000>;
 			reset-deassert-us = <1000>;
+			qca,smarteee-tw-us-1g = <24>;
+			qca,clk-out-frequency = <125000000>;
 		};
 	};
 };
diff --git a/arch/arm/mach-imx/mach-imx6q.c b/arch/arm/mach-imx/mach-imx6q.c
index 4c840e116003..d12b571a61ac 100644
--- a/arch/arm/mach-imx/mach-imx6q.c
+++ b/arch/arm/mach-imx/mach-imx6q.c
@@ -68,25 +68,6 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8609, ventana_pciesw_early_fixup);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8606, ventana_pciesw_early_fixup);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8604, ventana_pciesw_early_fixup);
 
-static int ar8031_phy_fixup(struct phy_device *dev)
-{
-	u16 val;
-
-	/* To enable AR8031 output a 125MHz clk from CLK_25M */
-	phy_write(dev, 0xd, 0x7);
-	phy_write(dev, 0xe, 0x8016);
-	phy_write(dev, 0xd, 0x4007);
-
-	val = phy_read(dev, 0xe);
-	val &= 0xffe3;
-	val |= 0x18;
-	phy_write(dev, 0xe, val);
-
-	return 0;
-}
-
-#define PHY_ID_AR8031	0x004dd074
-
 static int ar8035_phy_fixup(struct phy_device *dev)
 {
 	u16 val;
@@ -101,15 +82,6 @@ static int ar8035_phy_fixup(struct phy_device *dev)
 	val = phy_read(dev, 0xe);
 	phy_write(dev, 0xe, val & ~(1 << 8));
 
-	/*
-	 * Enable 125MHz clock from CLK_25M on the AR8031.  This
-	 * is fed in to the IMX6 on the ENET_REF_CLK (V22) pad.
-	 * Also, introduce a tx clock delay.
-	 *
-	 * This is the same as is the AR8031 fixup.
-	 */
-	ar8031_phy_fixup(dev);
-
 	return 0;
 }
 
@@ -120,8 +92,6 @@ static void __init imx6q_enet_phy_init(void)
 	if (IS_BUILTIN(CONFIG_PHYLIB)) {
 		phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
 				ksz9021rn_phy_fixup);
-		phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffef,
-				ar8031_phy_fixup);
 		phy_register_fixup_for_uid(PHY_ID_AR8035, 0xffffffef,
 				ar8035_phy_fixup);
 	}
-- 
2.29.2