From: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
To: Bjorn Andersson <bjorn.andersson@linaro.org>,
Ohad Ben-Cohen <ohad@wizery.com>,
Mathieu Poirier <mathieu.poirier@linaro.org>,
Rob Herring <robh@kernel.org>,
Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: <devicetree@vger.kernel.org>,
<linux-stm32@st-md-mailman.stormreply.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-remoteproc@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Subject: [PATCH v4 2/2] remoteproc: stm32: add capability to detach
Date: Wed, 31 Mar 2021 09:33:47 +0200 [thread overview]
Message-ID: <20210331073347.8293-3-arnaud.pouliquen@foss.st.com> (raw)
In-Reply-To: <20210331073347.8293-1-arnaud.pouliquen@foss.st.com>
A mechanism similar to the shutdown mailbox signal is implemented to
detach a remote processor.
Upon detachment, a signal is sent to the remote firmware, allowing it
to perform specific actions such as stopping rpmsg communication.
The Cortex-M hold boot is also disabled to allow the remote processor
to restart in case of crash.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
---
drivers/remoteproc/stm32_rproc.c | 39 ++++++++++++++++++++++++++++++--
1 file changed, 37 insertions(+), 2 deletions(-)
diff --git a/drivers/remoteproc/stm32_rproc.c b/drivers/remoteproc/stm32_rproc.c
index 3d45f51de4d0..7353f9e7e7af 100644
--- a/drivers/remoteproc/stm32_rproc.c
+++ b/drivers/remoteproc/stm32_rproc.c
@@ -28,7 +28,7 @@
#define RELEASE_BOOT 1
#define MBOX_NB_VQ 2
-#define MBOX_NB_MBX 3
+#define MBOX_NB_MBX 4
#define STM32_SMC_RCC 0x82001000
#define STM32_SMC_REG_WRITE 0x1
@@ -38,6 +38,7 @@
#define STM32_MBX_VQ1 "vq1"
#define STM32_MBX_VQ1_ID 1
#define STM32_MBX_SHUTDOWN "shutdown"
+#define STM32_MBX_DETACH "detach"
#define RSC_TBL_SIZE 1024
@@ -336,6 +337,15 @@ static const struct stm32_mbox stm32_rproc_mbox[MBOX_NB_MBX] = {
.tx_done = NULL,
.tx_tout = 500, /* 500 ms time out */
},
+ },
+ {
+ .name = STM32_MBX_DETACH,
+ .vq_id = -1,
+ .client = {
+ .tx_block = true,
+ .tx_done = NULL,
+ .tx_tout = 200, /* 200 ms time out to detach should be fair enough */
+ },
}
};
@@ -461,6 +471,25 @@ static int stm32_rproc_attach(struct rproc *rproc)
return stm32_rproc_set_hold_boot(rproc, true);
}
+static int stm32_rproc_detach(struct rproc *rproc)
+{
+ struct stm32_rproc *ddata = rproc->priv;
+ int err, dummy_data, idx;
+
+ /* Inform the remote processor of the detach */
+ idx = stm32_rproc_mbox_idx(rproc, STM32_MBX_DETACH);
+ if (idx >= 0 && ddata->mb[idx].chan) {
+ /* A dummy data is sent to allow to block on transmit */
+ err = mbox_send_message(ddata->mb[idx].chan,
+ &dummy_data);
+ if (err < 0)
+ dev_warn(&rproc->dev, "warning: remote FW detach without ack\n");
+ }
+
+ /* Allow remote processor to auto-reboot */
+ return stm32_rproc_set_hold_boot(rproc, false);
+}
+
static int stm32_rproc_stop(struct rproc *rproc)
{
struct stm32_rproc *ddata = rproc->priv;
@@ -597,7 +626,12 @@ stm32_rproc_get_loaded_rsc_table(struct rproc *rproc, size_t *table_sz)
}
done:
- /* Assuming the resource table fits in 1kB is fair */
+ /*
+ * Assuming the resource table fits in 1kB is fair.
+ * Notice for the detach, that this 1 kB memory area has to be reserved in the coprocessor
+ * firmware for the resource table. On detach, the remoteproc core re-initializes this
+ * entire area by overwriting it with the initial values stored in rproc->clean_table.
+ */
*table_sz = RSC_TBL_SIZE;
return (struct resource_table *)ddata->rsc_va;
}
@@ -607,6 +641,7 @@ static const struct rproc_ops st_rproc_ops = {
.start = stm32_rproc_start,
.stop = stm32_rproc_stop,
.attach = stm32_rproc_attach,
+ .detach = stm32_rproc_detach,
.kick = stm32_rproc_kick,
.load = rproc_elf_load_segments,
.parse_fw = stm32_rproc_parse_fw,
--
2.17.1
next prev parent reply other threads:[~2021-03-31 7:36 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-03-31 7:33 [PATCH v4 0/2] remoteproc: stm32: add support of detaching a remote processor Arnaud Pouliquen
2021-03-31 7:33 ` [PATCH v4 1/2] dt-bindings: remoteproc: stm32-rproc: add new mailbox channel for detach Arnaud Pouliquen
2021-03-31 7:33 ` Arnaud Pouliquen [this message]
2021-04-13 21:34 ` [PATCH v4 2/2] remoteproc: stm32: add capability to detach Bjorn Andersson
2021-04-14 7:23 ` Arnaud POULIQUEN
2021-04-14 15:01 ` Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210331073347.8293-3-arnaud.pouliquen@foss.st.com \
--to=arnaud.pouliquen@foss.st.com \
--cc=alexandre.torgue@foss.st.com \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mathieu.poirier@linaro.org \
--cc=ohad@wizery.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).