From: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
To: Felix Fietkau <nbd@nbd.name>, John Crispin <john@phrozen.org>,
Sean Wang <sean.wang@mediatek.com>,
Mark Lee <Mark-MC.Lee@mediatek.com>,
"David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Matthias Brugger <matthias.bgg@gmail.com>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-mediatek@lists.infradead.org
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Subject: [PATCH net-next 14/14] net: ethernet: mtk_eth_soc: use iopoll.h macro for DMA init
Date: Wed, 21 Apr 2021 21:09:14 -0700 [thread overview]
Message-ID: <20210422040914.47788-15-ilya.lipnitskiy@gmail.com> (raw)
In-Reply-To: <20210422040914.47788-1-ilya.lipnitskiy@gmail.com>
Replace a tight busy-wait loop without a pause with a standard
readx_poll_timeout_atomic routine with a 5 us poll period.
Tested by booting a MT7621 device to ensure the driver initializes
properly.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
---
drivers/net/ethernet/mediatek/mtk_eth_soc.c | 29 +++++++++------------
drivers/net/ethernet/mediatek/mtk_eth_soc.h | 2 +-
2 files changed, 14 insertions(+), 17 deletions(-)
diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index 8c863322587e..720d73d0c007 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -2037,25 +2037,22 @@ static int mtk_set_features(struct net_device *dev, netdev_features_t features)
/* wait for DMA to finish whatever it is doing before we start using it again */
static int mtk_dma_busy_wait(struct mtk_eth *eth)
{
- unsigned long t_start = jiffies;
+ u32 val;
+ int ret;
+ unsigned int reg;
- while (1) {
- if (MTK_HAS_CAPS(eth->soc->caps, MTK_QDMA)) {
- if (!(mtk_r32(eth, MTK_QDMA_GLO_CFG) &
- (MTK_RX_DMA_BUSY | MTK_TX_DMA_BUSY)))
- return 0;
- } else {
- if (!(mtk_r32(eth, MTK_PDMA_GLO_CFG) &
- (MTK_RX_DMA_BUSY | MTK_TX_DMA_BUSY)))
- return 0;
- }
+ if (MTK_HAS_CAPS(eth->soc->caps, MTK_QDMA))
+ reg = MTK_QDMA_GLO_CFG;
+ else
+ reg = MTK_PDMA_GLO_CFG;
- if (time_after(jiffies, t_start + MTK_DMA_BUSY_TIMEOUT))
- break;
- }
+ ret = readx_poll_timeout_atomic(__raw_readl, eth->base + reg, val,
+ !(val & (MTK_RX_DMA_BUSY | MTK_TX_DMA_BUSY)),
+ 5, MTK_DMA_BUSY_TIMEOUT_US);
+ if (ret)
+ dev_err(eth->dev, "DMA init timeout\n");
- dev_err(eth->dev, "DMA init timeout\n");
- return -1;
+ return ret;
}
static int mtk_dma_init(struct mtk_eth *eth)
diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.h b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
index 214da569e869..2e4356ccf778 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.h
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
@@ -214,7 +214,7 @@
#define MTK_TX_DMA_BUSY BIT(1)
#define MTK_RX_DMA_EN BIT(2)
#define MTK_TX_DMA_EN BIT(0)
-#define MTK_DMA_BUSY_TIMEOUT HZ
+#define MTK_DMA_BUSY_TIMEOUT_US 1000000
/* QDMA Reset Index Register */
#define MTK_QDMA_RST_IDX 0x1A08
--
2.31.1
next prev parent reply other threads:[~2021-04-22 4:11 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-04-22 4:09 [PATCH net-next 00/14] mtk_eth_soc: fixes and performance improvements Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 01/14] net: ethernet: mtk_eth_soc: fix RX VLAN offload Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 02/14] net: ethernet: mtk_eth_soc: unmap RX data before calling build_skb Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 03/14] net: ethernet: mtk_eth_soc: fix build_skb cleanup Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 04/14] net: ethernet: mtk_eth_soc: use napi_consume_skb Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 05/14] net: ethernet: mtk_eth_soc: reduce MDIO bus access latency Ilya Lipnitskiy
2021-04-22 12:18 ` Andrew Lunn
2021-04-22 12:33 ` Felix Fietkau
2021-04-23 4:16 ` Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 06/14] net: ethernet: mtk_eth_soc: remove unnecessary TX queue stops Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 07/14] net: ethernet: mtk_eth_soc: use larger burst size for QDMA TX Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 08/14] net: ethernet: mtk_eth_soc: increase DMA ring sizes Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 09/14] net: ethernet: mtk_eth_soc: implement dynamic interrupt moderation Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 10/14] net: ethernet: mtk_eth_soc: cache HW pointer of last freed TX descriptor Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 11/14] net: ethernet: mtk_eth_soc: only read the full RX descriptor if DMA is done Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 12/14] net: ethernet: mtk_eth_soc: reduce unnecessary interrupts Ilya Lipnitskiy
2021-04-22 16:26 ` Jakub Kicinski
2021-04-23 4:20 ` Ilya Lipnitskiy
2021-04-22 4:09 ` [PATCH net-next 13/14] net: ethernet: mtk_eth_soc: set PPE flow hash as skb hash if present Ilya Lipnitskiy
2021-04-22 4:09 ` Ilya Lipnitskiy [this message]
2021-04-22 12:20 ` [PATCH net-next 14/14] net: ethernet: mtk_eth_soc: use iopoll.h macro for DMA init Andrew Lunn
2021-04-22 12:23 ` [PATCH net-next 00/14] mtk_eth_soc: fixes and performance improvements Andrew Lunn
2021-04-23 4:18 ` Ilya Lipnitskiy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210422040914.47788-15-ilya.lipnitskiy@gmail.com \
--to=ilya.lipnitskiy@gmail.com \
--cc=Mark-MC.Lee@mediatek.com \
--cc=davem@davemloft.net \
--cc=john@phrozen.org \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=nbd@nbd.name \
--cc=netdev@vger.kernel.org \
--cc=sean.wang@mediatek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).