linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: ira.weiny@intel.com
To: Ben Widawsky <ben.widawsky@intel.com>,
	Dan Williams <dan.j.williams@intel.com>,
	Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Ira Weiny <ira.weiny@intel.com>,
	Alison Schofield <alison.schofield@intel.com>,
	Vishal Verma <vishal.l.verma@intel.com>,
	linux-cxl@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH V3 2/5] cxl/mem: Reserve all device regions at once
Date: Thu, 27 May 2021 17:49:19 -0700	[thread overview]
Message-ID: <20210528004922.3980613-3-ira.weiny@intel.com> (raw)
In-Reply-To: <20210528004922.3980613-1-ira.weiny@intel.com>

From: Ira Weiny <ira.weiny@intel.com>

In order to remap individual register sets each bar region must be
reserved prior to mapping.  Because the details of individual register
sets are contained within the BARs themselves, the bar must be mapped 2
times, once to extract this information and a second time for each
register set.

Rather than attempt to reserve each BAR individually and track if that
bar has been reserved.  Open code pcim_iomap_regions() by first
reserving all memory regions on the device and then mapping the bars
individually as needed.

NOTE pci_request_mem_regions() does not need a corresponding
pci_release_mem_regions() because the pci device is managed via
pcim_enable_device().

Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
---
 drivers/cxl/pci.c | 18 +++++++++++-------
 1 file changed, 11 insertions(+), 7 deletions(-)

diff --git a/drivers/cxl/pci.c b/drivers/cxl/pci.c
index b2f978954daa..33fc6e1634e3 100644
--- a/drivers/cxl/pci.c
+++ b/drivers/cxl/pci.c
@@ -927,7 +927,7 @@ static void __iomem *cxl_mem_map_regblock(struct cxl_mem *cxlm,
 {
 	struct pci_dev *pdev = cxlm->pdev;
 	struct device *dev = &pdev->dev;
-	int rc;
+	void __iomem *addr;
 
 	/* Basic sanity check that BAR is big enough */
 	if (pci_resource_len(pdev, bar) < offset) {
@@ -936,13 +936,14 @@ static void __iomem *cxl_mem_map_regblock(struct cxl_mem *cxlm,
 		return IOMEM_ERR_PTR(-ENXIO);
 	}
 
-	rc = pcim_iomap_regions(pdev, BIT(bar), pci_name(pdev));
-	if (rc) {
+	addr = pcim_iomap(pdev, bar, 0);
+	if (!addr) {
 		dev_err(dev, "failed to map registers\n");
-		return IOMEM_ERR_PTR(rc);
+		return addr;
 	}
 
-	dev_dbg(dev, "Mapped CXL Memory Device resource\n");
+	dev_dbg(dev, "Mapped CXL Memory Device resource bar %u @ %#llx\n",
+		bar, offset);
 
 	return pcim_iomap_table(pdev)[bar] + offset;
 }
@@ -1003,6 +1004,9 @@ static int cxl_mem_setup_regs(struct cxl_mem *cxlm)
 		return -ENXIO;
 	}
 
+	if (pci_request_mem_regions(pdev, pci_name(pdev)))
+		return -ENODEV;
+
 	/* Get the size of the Register Locator DVSEC */
 	pci_read_config_dword(pdev, regloc + PCI_DVSEC_HEADER1, &regloc_size);
 	regloc_size = FIELD_GET(PCI_DVSEC_HEADER1_LENGTH_MASK, regloc_size);
@@ -1028,8 +1032,8 @@ static int cxl_mem_setup_regs(struct cxl_mem *cxlm)
 
 		if (reg_type == CXL_REGLOC_RBI_MEMDEV) {
 			base = cxl_mem_map_regblock(cxlm, bar, offset);
-			if (IS_ERR(base))
-				return PTR_ERR(base);
+			if (!base)
+				return -ENOMEM;
 			break;
 		}
 	}
-- 
2.28.0.rc0.12.gb6a658bd00c9


  parent reply	other threads:[~2021-05-28  0:49 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-05-28  0:49 [PATCH V3 0/5] Map register blocks individually ira.weiny
2021-05-28  0:49 ` [PATCH V3 1/5] cxl/mem: Introduce cxl_decode_register_block() ira.weiny
2021-05-28  0:49 ` ira.weiny [this message]
2021-05-28  0:49 ` [PATCH V3 3/5] cxl/mem: Map registers based on capabilities ira.weiny
2021-06-04  0:50   ` [PATCH V3.1] " ira.weiny
2021-06-06  0:30     ` Dan Williams
2021-05-28  0:49 ` [PATCH V3 4/5] cxl/mem: Reserve individual register block regions ira.weiny
2021-06-04  0:53   ` [PATCH V3.1] " ira.weiny
2021-05-28  0:49 ` [PATCH V3 5/5] cxl/pci: Add HDM decoder capabilities ira.weiny

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210528004922.3980613-3-ira.weiny@intel.com \
    --to=ira.weiny@intel.com \
    --cc=Jonathan.Cameron@huawei.com \
    --cc=alison.schofield@intel.com \
    --cc=ben.widawsky@intel.com \
    --cc=dan.j.williams@intel.com \
    --cc=linux-cxl@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=vishal.l.verma@intel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).