* [PATCH] arm64: dts: ti: Drop reg-io-width/reg-shift from UART nodes
@ 2021-06-07 13:45 Vignesh Raghavendra
2021-06-09 14:13 ` Lokesh Vutla
2021-06-11 19:00 ` Nishanth Menon
0 siblings, 2 replies; 3+ messages in thread
From: Vignesh Raghavendra @ 2021-06-07 13:45 UTC (permalink / raw)
To: Nishanth Menon
Cc: Rob Herring, Vignesh Raghavendra, devicetree, linux-kernel,
Linux ARM Mailing List
8250_omap compatible UART IPs on all SoCs have registers aligned at 4
byte address boundary and constant byte addressability. Thus there is no
need for reg-io-width or reg-shift DT properties. These properties are
not used by 8250_omap driver nor documented as part of binding document.
Therefore drop them.
This is in preparation to move omap-serial.txt to YAML format.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 14 -------------
arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi | 4 ----
arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 6 ------
arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi | 2 --
arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 --
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 20 -------------------
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 4 ----
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 20 -------------------
.../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ----
9 files changed, 76 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
index ca59d1f711f8..f1c42ef05e52 100644
--- a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
@@ -189,8 +189,6 @@ phy_gmii_sel: phy@4044 {
main_uart0: serial@2800000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x02800000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -202,8 +200,6 @@ main_uart0: serial@2800000 {
main_uart1: serial@2810000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x02810000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -215,8 +211,6 @@ main_uart1: serial@2810000 {
main_uart2: serial@2820000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x02820000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -228,8 +222,6 @@ main_uart2: serial@2820000 {
main_uart3: serial@2830000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x02830000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -241,8 +233,6 @@ main_uart3: serial@2830000 {
main_uart4: serial@2840000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x02840000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -254,8 +244,6 @@ main_uart4: serial@2840000 {
main_uart5: serial@2850000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x02850000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -267,8 +255,6 @@ main_uart5: serial@2850000 {
main_uart6: serial@2860000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x02860000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
diff --git a/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi
index deb19ae5e168..20274df5f216 100644
--- a/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi
@@ -9,8 +9,6 @@ &cbass_mcu {
mcu_uart0: serial@4a00000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x04a00000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -22,8 +20,6 @@ mcu_uart0: serial@4a00000 {
mcu_uart1: serial@4a10000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x04a10000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 6cd3131eb9ff..05964943a4a4 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -84,8 +84,6 @@ serdes1: serdes@910000 {
main_uart0: serial@2800000 {
compatible = "ti,am654-uart";
reg = <0x00 0x02800000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -95,8 +93,6 @@ main_uart0: serial@2800000 {
main_uart1: serial@2810000 {
compatible = "ti,am654-uart";
reg = <0x00 0x02810000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
@@ -105,8 +101,6 @@ main_uart1: serial@2810000 {
main_uart2: serial@2820000 {
compatible = "ti,am654-uart";
reg = <0x00 0x02820000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
index f5b8ef2f5f77..c93ff1520a0e 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
@@ -23,8 +23,6 @@ phy_gmii_sel: phy@4040 {
mcu_uart0: serial@40a00000 {
compatible = "ti,am654-uart";
reg = <0x00 0x40a00000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 565 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <96000000>;
current-speed = <115200>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index 7cb864b4d74a..9d21cdf6fce8 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -50,8 +50,6 @@ wkup_pmx0: pinctrl@4301c000 {
wkup_uart0: serial@42300000 {
compatible = "ti,am654-uart";
reg = <0x42300000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 19fea8adbcff..5a2f75a455c5 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -301,8 +301,6 @@ main_pmx0: pinctrl@11c000 {
main_uart0: serial@2800000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02800000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -314,8 +312,6 @@ main_uart0: serial@2800000 {
main_uart1: serial@2810000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02810000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -327,8 +323,6 @@ main_uart1: serial@2810000 {
main_uart2: serial@2820000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02820000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -340,8 +334,6 @@ main_uart2: serial@2820000 {
main_uart3: serial@2830000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02830000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -353,8 +345,6 @@ main_uart3: serial@2830000 {
main_uart4: serial@2840000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02840000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -366,8 +356,6 @@ main_uart4: serial@2840000 {
main_uart5: serial@2850000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02850000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -379,8 +367,6 @@ main_uart5: serial@2850000 {
main_uart6: serial@2860000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02860000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -392,8 +378,6 @@ main_uart6: serial@2860000 {
main_uart7: serial@2870000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02870000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -405,8 +389,6 @@ main_uart7: serial@2870000 {
main_uart8: serial@2880000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02880000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -418,8 +400,6 @@ main_uart8: serial@2880000 {
main_uart9: serial@2890000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02890000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 5663fe3ea466..5f069b55f449 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -73,8 +73,6 @@ mcu_ram: sram@41c00000 {
wkup_uart0: serial@42300000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x42300000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -86,8 +84,6 @@ wkup_uart0: serial@42300000 {
mcu_uart0: serial@40a00000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x40a00000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <96000000>;
current-speed = <115200>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 3bcafe4c1742..8a0e29636074 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -775,8 +775,6 @@ pcie3_ep: pcie-ep@2930000 {
main_uart0: serial@2800000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02800000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -788,8 +786,6 @@ main_uart0: serial@2800000 {
main_uart1: serial@2810000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02810000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -801,8 +797,6 @@ main_uart1: serial@2810000 {
main_uart2: serial@2820000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02820000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -814,8 +808,6 @@ main_uart2: serial@2820000 {
main_uart3: serial@2830000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02830000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -827,8 +819,6 @@ main_uart3: serial@2830000 {
main_uart4: serial@2840000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02840000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -840,8 +830,6 @@ main_uart4: serial@2840000 {
main_uart5: serial@2850000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02850000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -853,8 +841,6 @@ main_uart5: serial@2850000 {
main_uart6: serial@2860000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02860000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -866,8 +852,6 @@ main_uart6: serial@2860000 {
main_uart7: serial@2870000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02870000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -879,8 +863,6 @@ main_uart7: serial@2870000 {
main_uart8: serial@2880000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02880000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -892,8 +874,6 @@ main_uart8: serial@2880000 {
main_uart9: serial@2890000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x02890000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 5e825e4d0306..d2dceda72fe9 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -73,8 +73,6 @@ mcu_ram: sram@41c00000 {
wkup_uart0: serial@42300000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x42300000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <48000000>;
current-speed = <115200>;
@@ -86,8 +84,6 @@ wkup_uart0: serial@42300000 {
mcu_uart0: serial@40a00000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x40a00000 0x00 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
interrupts = <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <96000000>;
current-speed = <115200>;
--
2.31.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] arm64: dts: ti: Drop reg-io-width/reg-shift from UART nodes
2021-06-07 13:45 [PATCH] arm64: dts: ti: Drop reg-io-width/reg-shift from UART nodes Vignesh Raghavendra
@ 2021-06-09 14:13 ` Lokesh Vutla
2021-06-11 19:00 ` Nishanth Menon
1 sibling, 0 replies; 3+ messages in thread
From: Lokesh Vutla @ 2021-06-09 14:13 UTC (permalink / raw)
To: Vignesh Raghavendra, Nishanth Menon
Cc: Rob Herring, devicetree, linux-kernel, Linux ARM Mailing List
On 07/06/21 7:15 pm, Vignesh Raghavendra wrote:
> 8250_omap compatible UART IPs on all SoCs have registers aligned at 4
> byte address boundary and constant byte addressability. Thus there is no
> need for reg-io-width or reg-shift DT properties. These properties are
> not used by 8250_omap driver nor documented as part of binding document.
> Therefore drop them.
>
> This is in preparation to move omap-serial.txt to YAML format.
>
> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Thanks and regards,
Lokesh
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] arm64: dts: ti: Drop reg-io-width/reg-shift from UART nodes
2021-06-07 13:45 [PATCH] arm64: dts: ti: Drop reg-io-width/reg-shift from UART nodes Vignesh Raghavendra
2021-06-09 14:13 ` Lokesh Vutla
@ 2021-06-11 19:00 ` Nishanth Menon
1 sibling, 0 replies; 3+ messages in thread
From: Nishanth Menon @ 2021-06-11 19:00 UTC (permalink / raw)
To: Vignesh Raghavendra
Cc: Nishanth Menon, Linux ARM Mailing List, devicetree, Rob Herring,
linux-kernel
On Mon, 7 Jun 2021 19:15:58 +0530, Vignesh Raghavendra wrote:
> 8250_omap compatible UART IPs on all SoCs have registers aligned at 4
> byte address boundary and constant byte addressability. Thus there is no
> need for reg-io-width or reg-shift DT properties. These properties are
> not used by 8250_omap driver nor documented as part of binding document.
> Therefore drop them.
>
> This is in preparation to move omap-serial.txt to YAML format.
Hi Vignesh Raghavendra,
I have applied the following to branch ti-k3-dts-next on [1].
Thank you!
[1/1] arm64: dts: ti: Drop reg-io-width/reg-shift from UART nodes
commit: 53af668e7c154c33f69e3f631261155b0cf2a784
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
[1] git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux.git
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2021-06-11 19:01 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-06-07 13:45 [PATCH] arm64: dts: ti: Drop reg-io-width/reg-shift from UART nodes Vignesh Raghavendra
2021-06-09 14:13 ` Lokesh Vutla
2021-06-11 19:00 ` Nishanth Menon
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).