linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Sebastian Reichel <sebastian.reichel@collabora.com>
To: Mark Brown <broonie@kernel.org>, Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Shawn Guo <shawnguo@kernel.org>,
	Sascha Hauer <kernel@pengutronix.de>,
	Fabio Estevam <festevam@gmail.com>, Ian Ray <ian.ray@ge.com>,
	linux-kernel@vger.kernel.org, linux-spi@vger.kernel.org,
	devicetree@vger.kernel.org, kernel@collabora.com,
	Sebastian Reichel <sebastian.reichel@collabora.com>
Subject: [PATCHv4 6/6] misc: gehc-achc: new driver
Date: Wed,  9 Jun 2021 17:12:35 +0200	[thread overview]
Message-ID: <20210609151235.48964-7-sebastian.reichel@collabora.com> (raw)
In-Reply-To: <20210609151235.48964-1-sebastian.reichel@collabora.com>

General Electric Healthcare's PPD has a secondary processor from
NXP's Kinetis K20 series. That device has two SPI chip selects:

The main interface's behaviour depends on the loaded firmware
and is currently unused.

The secondary interface can be used to update the firmware using
EzPort protocol. This is implemented by this driver using the
kernel's firmware API. It's not done during probe time, since
the device has non-volatile memory and flashing lasts almost 3
minutes.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 .../ABI/testing/sysfs-driver-ge-achc          |   9 ++
 drivers/misc/Kconfig                          |  12 ++
 drivers/misc/Makefile                         |   1 +
 drivers/misc/gehc-achc.c                      | 136 ++++++++++++++++++
 drivers/spi/spidev.c                          |   1 -
 5 files changed, 158 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/ABI/testing/sysfs-driver-ge-achc
 create mode 100644 drivers/misc/gehc-achc.c

diff --git a/Documentation/ABI/testing/sysfs-driver-ge-achc b/Documentation/ABI/testing/sysfs-driver-ge-achc
new file mode 100644
index 000000000000..3ca71a1b4836
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-ge-achc
@@ -0,0 +1,9 @@
+What:		/sys/bus/spi/drivers/gehc-achc/<dev>/update_firmware
+Date:		June 2021
+Contact:	linux-kernel@vger.kernel.org
+Description:	Write 1 to this file to trigger a firmware update.
+
+What:		/sys/bus/spi/drivers/gehc-achc/<dev>/reset
+Date:		June 2021
+Contact:	linux-kernel@vger.kernel.org
+Description:	Write 1 to this file to trigger a device reset.
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index 392c091891a1..a286f0775f2e 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -211,6 +211,18 @@ config CS5535_CLOCK_EVENT_SRC
 config NXP_EZPORT
 	tristate
 
+config GEHC_ACHC
+	tristate "GEHC ACHC support"
+	depends on SPI && SYSFS && SPI_SPIDEV
+	select FW_LOADER
+	select NXP_EZPORT
+	help
+	  Support for GE ACHC microcontroller, that is part of the GE
+	  PPD device.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called gehc-achc.
+
 config HP_ILO
 	tristate "Channel interface driver for the HP iLO processor"
 	depends on PCI
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index a85e763b9b33..b7bad5a16c8f 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -25,6 +25,7 @@ obj-$(CONFIG_SGI_XP)		+= sgi-xp/
 obj-$(CONFIG_SGI_GRU)		+= sgi-gru/
 obj-$(CONFIG_CS5535_MFGPT)	+= cs5535-mfgpt.o
 obj-$(CONFIG_NXP_EZPORT)	+= nxp-ezport.o
+obj-$(CONFIG_GEHC_ACHC)		+= gehc-achc.o
 obj-$(CONFIG_HP_ILO)		+= hpilo.o
 obj-$(CONFIG_APDS9802ALS)	+= apds9802als.o
 obj-$(CONFIG_ISL29003)		+= isl29003.o
diff --git a/drivers/misc/gehc-achc.c b/drivers/misc/gehc-achc.c
new file mode 100644
index 000000000000..5868ac99a3f6
--- /dev/null
+++ b/drivers/misc/gehc-achc.c
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * datasheet: https://www.nxp.com/docs/en/data-sheet/K20P144M120SF3.pdf
+ *
+ * Copyright (C) 2018-2021 Collabora
+ * Copyright (C) 2018-2021 GE Healthcare
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+#include <linux/of.h>
+#include <linux/platform_data/nxp-ezport.h>
+
+#define ACHC_MAX_FREQ 300000
+
+struct achc_data {
+	struct spi_device *main;
+	struct spi_device *ezport;
+	struct gpio_desc *reset;
+
+	struct mutex device_lock; /* avoid concurrent device access */
+};
+
+static ssize_t update_firmware_store(struct device *dev, struct device_attribute *attr,
+				     const char *buf, size_t count)
+{
+	struct achc_data *achc = dev_get_drvdata(dev);
+	int ret;
+
+	if (!count)
+		return -EINVAL;
+
+	mutex_lock(&achc->device_lock);
+	ret = ezport_flash(achc->ezport, achc->reset, "achc.bin");
+	mutex_unlock(&achc->device_lock);
+
+	if (ret < 0)
+		return ret;
+
+	return count;
+}
+static DEVICE_ATTR_WO(update_firmware);
+
+static ssize_t reset_store(struct device *dev, struct device_attribute *attr,
+			   const char *buf, size_t count)
+{
+	struct achc_data *achc = dev_get_drvdata(dev);
+
+	if (!count)
+		return -EINVAL;
+
+	mutex_lock(&achc->device_lock);
+	ezport_reset(achc->reset);
+	mutex_unlock(&achc->device_lock);
+
+	return count;
+}
+static DEVICE_ATTR_WO(reset);
+
+static struct attribute *gehc_achc_attrs[] = {
+	&dev_attr_update_firmware.attr,
+	&dev_attr_reset.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(gehc_achc);
+
+static void unregister_ezport(void *data)
+{
+	struct spi_device *ezport = data;
+
+	spi_unregister_device(ezport);
+}
+
+static int gehc_achc_probe(struct spi_device *spi)
+{
+	struct achc_data *achc;
+	int ezport_reg, ret;
+
+	spi->max_speed_hz = ACHC_MAX_FREQ;
+	spi->bits_per_word = 8;
+	spi->mode = SPI_MODE_0;
+
+	achc = devm_kzalloc(&spi->dev, sizeof(*achc), GFP_KERNEL);
+	if (!achc)
+		return -ENOMEM;
+	spi_set_drvdata(spi, achc);
+	achc->main = spi;
+
+	mutex_init(&achc->device_lock);
+
+	ret = of_property_read_u32_index(spi->dev.of_node, "reg", 1, &ezport_reg);
+	if (ret)
+		return dev_err_probe(&spi->dev, ret, "missing second reg entry!\n");
+
+	achc->ezport = spi_new_ancillary_device(spi, ezport_reg);
+	if (IS_ERR(achc->ezport))
+		return PTR_ERR(achc->ezport);
+
+	ret = devm_add_action_or_reset(&spi->dev, unregister_ezport, achc->ezport);
+	if (ret)
+		return ret;
+
+	achc->reset = devm_gpiod_get(&spi->dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(achc->reset))
+		return dev_err_probe(&spi->dev, PTR_ERR(achc->reset), "Could not get reset gpio\n");
+
+	return 0;
+}
+
+static const struct spi_device_id gehc_achc_id[] = {
+	{ "ge,achc", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, gehc_achc_id);
+
+static const struct of_device_id gehc_achc_of_match[] = {
+	{ .compatible = "ge,achc" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, gehc_achc_of_match);
+
+static struct spi_driver gehc_achc_spi_driver = {
+	.driver = {
+		.name	= "gehc-achc",
+		.of_match_table = gehc_achc_of_match,
+		.dev_groups = gehc_achc_groups,
+	},
+	.probe		= gehc_achc_probe,
+	.id_table	= gehc_achc_id,
+};
+module_spi_driver(gehc_achc_spi_driver);
+
+MODULE_DESCRIPTION("GEHC ACHC driver");
+MODULE_AUTHOR("Sebastian Reichel <sebastian.reichel@collabora.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/spi/spidev.c b/drivers/spi/spidev.c
index f56e0e975a46..d0d9dbbbdec1 100644
--- a/drivers/spi/spidev.c
+++ b/drivers/spi/spidev.c
@@ -677,7 +677,6 @@ static struct class *spidev_class;
 static const struct of_device_id spidev_dt_ids[] = {
 	{ .compatible = "rohm,dh2228fv" },
 	{ .compatible = "lineartechnology,ltc2488" },
-	{ .compatible = "ge,achc" },
 	{ .compatible = "semtech,sx1301" },
 	{ .compatible = "lwn,bk4" },
 	{ .compatible = "dh,dhcom-board" },
-- 
2.30.2


  parent reply	other threads:[~2021-06-09 15:13 UTC|newest]

Thread overview: 16+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-06-09 15:12 [PATCHv4 0/6] GE Healthcare PPD firmware upgrade driver for ACHC Sebastian Reichel
2021-06-09 15:12 ` [PATCHv4 1/6] spi: add ancillary device support Sebastian Reichel
2021-06-11  9:06   ` Greg Kroah-Hartman
2021-06-11 17:22     ` Sebastian Reichel
2021-06-13 14:18   ` Andy Shevchenko
2021-06-17 12:51   ` Mark Brown
2021-06-09 15:12 ` [PATCHv4 2/6] spi: dt-bindings: support devices with multiple chipselects Sebastian Reichel
2021-06-09 15:12 ` [PATCHv4 3/6] dt-bindings: misc: ge-achc: Convert to DT schema format Sebastian Reichel
2021-06-10 16:41   ` Rob Herring
2021-06-09 15:12 ` [PATCHv4 4/6] ARM: dts: imx53-ppd: Fix ACHC entry Sebastian Reichel
2021-06-09 15:12 ` [PATCHv4 5/6] misc: nxp-ezport: introduce EzPort support Sebastian Reichel
2021-06-11  9:05   ` Greg Kroah-Hartman
2021-06-11  9:45     ` Greg Kroah-Hartman
2021-06-09 15:12 ` Sebastian Reichel [this message]
2021-06-11  9:02   ` [PATCHv4 6/6] misc: gehc-achc: new driver Greg Kroah-Hartman
2021-06-22 15:14 ` (subset) [PATCHv4 0/6] GE Healthcare PPD firmware upgrade driver for ACHC Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210609151235.48964-7-sebastian.reichel@collabora.com \
    --to=sebastian.reichel@collabora.com \
    --cc=arnd@arndb.de \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=ian.ray@ge.com \
    --cc=kernel@collabora.com \
    --cc=kernel@pengutronix.de \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=shawnguo@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).