From: Peter Chen <peter.chen@kernel.org>
To: Breno Lima <breno.lima@nxp.com>
Cc: gregkh@linuxfoundation.org, shawnguo@kernel.org,
s.hauer@pengutronix.de, kernel@pengutronix.de,
festevam@gmail.com, linux-imx@nxp.com, linux-usb@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, brenomatheus@gmail.com,
jun.li@nxp.com
Subject: Re: [PATCH v2] mx8mm: usb: chipidea: Fix Battery Charger 1.2 CDP detection
Date: Sat, 12 Jun 2021 15:24:38 +0800 [thread overview]
Message-ID: <20210612072438.GA4580@Peter> (raw)
In-Reply-To: <20210611145607.147207-1-breno.lima@nxp.com>
On 21-06-11 10:56:07, Breno Lima wrote:
> i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
> following CDP timing requirements defined by USB BC 1.2 specification
> and section 3.2.4 Detection Timing CDP.
>
> During Primary Detection the i.MX device should turn on VDP_SRC and
> IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
> the PD is allowed to check the status of the D- line. Current
> implementation is waiting between 1ms and 2ms, and certain BC 1.2
> complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
> enough time for primary detection.
>
> During secondary detection the PD is required to disable VDP_SRC and
What does the "PD" mean here?
> IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).
>
> Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
> disable sequence in imx7d_charger_secondary_detection() function.
>
> VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
> Increase delay allowing enough time for detection.
>
> Fixes: 746f316b753a ("usb: chipidea: introduce imx7d USB charger detection")
I assume this one needs to go stable tree?
Peter
>
> Signed-off-by: Breno Lima <breno.lima@nxp.com>
> Signed-off-by: Jun Li <jun.li@nxp.com>
> ---
> Changes since V1:
> - Updated commit log to include commit ID fix
> drivers/usb/chipidea/usbmisc_imx.c | 16 ++++++++++++++--
> 1 file changed, 14 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/usb/chipidea/usbmisc_imx.c b/drivers/usb/chipidea/usbmisc_imx.c
> index 4545b23bda3f..bac0f5458cab 100644
> --- a/drivers/usb/chipidea/usbmisc_imx.c
> +++ b/drivers/usb/chipidea/usbmisc_imx.c
> @@ -686,6 +686,16 @@ static int imx7d_charger_secondary_detection(struct imx_usbmisc_data *data)
> int val;
> unsigned long flags;
>
> + /* Clear VDATSRCENB0 to disable VDP_SRC and IDM_SNK required by BC 1.2 spec */
> + spin_lock_irqsave(&usbmisc->lock, flags);
> + val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
> + val &= ~MX7D_USB_OTG_PHY_CFG2_CHRG_VDATSRCENB0;
> + writel(val, usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
> + spin_unlock_irqrestore(&usbmisc->lock, flags);
> +
> + /* TVDMSRC_DIS */
> + msleep(20);
> +
> /* VDM_SRC is connected to D- and IDP_SINK is connected to D+ */
> spin_lock_irqsave(&usbmisc->lock, flags);
> val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
> @@ -695,7 +705,8 @@ static int imx7d_charger_secondary_detection(struct imx_usbmisc_data *data)
> usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
> spin_unlock_irqrestore(&usbmisc->lock, flags);
>
> - usleep_range(1000, 2000);
> + /* TVDMSRC_ON */
> + msleep(40);
>
> /*
> * Per BC 1.2, check voltage of D+:
> @@ -798,7 +809,8 @@ static int imx7d_charger_primary_detection(struct imx_usbmisc_data *data)
> usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
> spin_unlock_irqrestore(&usbmisc->lock, flags);
>
> - usleep_range(1000, 2000);
> + /* TVDPSRC_ON */
> + msleep(40);
>
> /* Check if D- is less than VDAT_REF to determine an SDP per BC 1.2 */
> val = readl(usbmisc->base + MX7D_USB_OTG_PHY_STATUS);
> --
> 2.25.1
>
--
Thanks,
Peter Chen
next prev parent reply other threads:[~2021-06-12 7:24 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-11 14:56 [PATCH v2] mx8mm: usb: chipidea: Fix Battery Charger 1.2 CDP detection Breno Lima
2021-06-12 7:24 ` Peter Chen [this message]
2021-06-12 17:59 ` Breno Matheus Lima
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210612072438.GA4580@Peter \
--to=peter.chen@kernel.org \
--cc=breno.lima@nxp.com \
--cc=brenomatheus@gmail.com \
--cc=festevam@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=jun.li@nxp.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).