linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Alistair Francis <alistair@alistair23.me>
To: lee.jones@linaro.org, robh+dt@kernel.org, lgirdwood@gmail.com,
	broonie@kernel.org, linux-imx@nxp.com, kernel@pengutronix.de
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	alistair23@gmail.com, Alistair Francis <alistair@alistair23.me>
Subject: [PATCH v6 3/5] regulator: sy7636a: Initial commit
Date: Tue, 15 Jun 2021 20:33:58 +1000	[thread overview]
Message-ID: <20210615103400.946-3-alistair@alistair23.me> (raw)
In-Reply-To: <20210615103400.946-1-alistair@alistair23.me>

Initial support for the Silergy SY7636A-regulator Power Management chip.

Signed-off-by: Alistair Francis <alistair@alistair23.me>
---
 drivers/regulator/Kconfig             |   6 ++
 drivers/regulator/Makefile            |   1 +
 drivers/regulator/sy7636a-regulator.c | 127 ++++++++++++++++++++++++++
 3 files changed, 134 insertions(+)
 create mode 100644 drivers/regulator/sy7636a-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 3e7a38525cb3..ebb968e8b2b0 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1150,6 +1150,12 @@ config REGULATOR_STW481X_VMMC
 	  This driver supports the internal VMMC regulator in the STw481x
 	  PMIC chips.
 
+config REGULATOR_SY7636A
+	tristate "Silergy SY7636A voltage regulator"
+	depends on MFD_SY7636A
+	help
+	  This driver supports Silergy SY3686A voltage regulator.
+
 config REGULATOR_SY8106A
 	tristate "Silergy SY8106A regulator"
 	depends on I2C && (OF || COMPILE_TEST)
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 580b015296ea..b17c24d93f3b 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -136,6 +136,7 @@ obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
 obj-$(CONFIG_REGULATOR_STM32_PWR) += stm32-pwr.o
 obj-$(CONFIG_REGULATOR_STPMIC1) += stpmic1_regulator.o
 obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
+obj-$(CONFIG_REGULATOR_SY7636A) += sy7636a-regulator.o
 obj-$(CONFIG_REGULATOR_SY8106A) += sy8106a-regulator.o
 obj-$(CONFIG_REGULATOR_SY8824X) += sy8824x.o
 obj-$(CONFIG_REGULATOR_SY8827N) += sy8827n.o
diff --git a/drivers/regulator/sy7636a-regulator.c b/drivers/regulator/sy7636a-regulator.c
new file mode 100644
index 000000000000..c384c2b6ac46
--- /dev/null
+++ b/drivers/regulator/sy7636a-regulator.c
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Functions to access SY3686A power management chip voltages
+//
+// Copyright (C) 2019 reMarkable AS - http://www.remarkable.com/
+//
+// Authors: Lars Ivar Miljeteig <lars.ivar.miljeteig@remarkable.com>
+//          Alistair Francis <alistair@alistair23.me>
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mfd/sy7636a.h>
+
+#define SY7636A_POLL_ENABLED_TIME 500
+
+static int sy7636a_get_vcom_voltage_op(struct regulator_dev *rdev)
+{
+	int ret;
+	unsigned int val, val_h;
+
+	ret = regmap_read(rdev->regmap, SY7636A_REG_VCOM_ADJUST_CTRL_L, &val);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(rdev->regmap, SY7636A_REG_VCOM_ADJUST_CTRL_H, &val_h);
+	if (ret)
+		return ret;
+
+	val |= (val_h << VCOM_ADJUST_CTRL_SHIFT);
+
+	return (val & VCOM_ADJUST_CTRL_MASK) * VCOM_ADJUST_CTRL_SCAL;
+}
+
+static int sy7636a_get_status(struct regulator_dev *rdev)
+{
+	struct sy7636a *sy7636a = dev_get_drvdata(rdev->dev.parent);
+	int ret = 0;
+
+	ret = gpiod_get_value_cansleep(sy7636a->pgood_gpio);
+	if (ret < 0)
+		dev_err(&rdev->dev, "Failed to read pgood gpio: %d\n", ret);
+
+	return ret;
+}
+
+static const struct regulator_ops sy7636a_vcom_volt_ops = {
+	.get_voltage = sy7636a_get_vcom_voltage_op,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.get_status = sy7636a_get_status,
+};
+
+struct regulator_desc desc = {
+	.name = "vcom",
+	.id = 0,
+	.ops = &sy7636a_vcom_volt_ops,
+	.type = REGULATOR_VOLTAGE,
+	.owner = THIS_MODULE,
+	.enable_reg = SY7636A_REG_OPERATION_MODE_CRL,
+	.enable_mask = SY7636A_OPERATION_MODE_CRL_ONOFF,
+	.poll_enabled_time	= SY7636A_POLL_ENABLED_TIME,
+	.regulators_node = of_match_ptr("regulators"),
+	.of_match = of_match_ptr("vcom"),
+};
+
+static int sy7636a_regulator_probe(struct platform_device *pdev)
+{
+	struct sy7636a *sy7636a = dev_get_drvdata(pdev->dev.parent);
+	struct regulator_config config = { };
+	struct regulator_dev *rdev;
+	struct gpio_desc *gdp;
+	int ret;
+
+	if (!sy7636a)
+		return -EPROBE_DEFER;
+
+	platform_set_drvdata(pdev, sy7636a);
+
+	gdp = devm_gpiod_get(sy7636a->dev, "epd-pwr-good", GPIOD_IN);
+	if (IS_ERR(gdp)) {
+		dev_err(sy7636a->dev, "Power good GPIO fault %ld\n", PTR_ERR(gdp));
+		return PTR_ERR(gdp);
+	}
+
+	sy7636a->pgood_gpio = gdp;
+
+	ret = regmap_write(sy7636a->regmap, SY7636A_REG_POWER_ON_DELAY_TIME, 0x0);
+	if (ret) {
+		dev_err(sy7636a->dev, "Failed to initialize regulator: %d\n", ret);
+		return ret;
+	}
+
+	config.dev = &pdev->dev;
+	config.dev->of_node = sy7636a->dev->of_node;
+	config.driver_data = sy7636a;
+	config.regmap = sy7636a->regmap;
+
+	rdev = devm_regulator_register(&pdev->dev, &desc, &config);
+	if (IS_ERR(rdev)) {
+		dev_err(sy7636a->dev, "Failed to register %s regulator\n",
+			pdev->name);
+		return PTR_ERR(rdev);
+	}
+
+	return 0;
+}
+
+static const struct platform_device_id sy7636a_regulator_id_table[] = {
+	{ "sy7636a-regulator", },
+};
+MODULE_DEVICE_TABLE(platform, sy7636a_regulator_id_table);
+
+static struct platform_driver sy7636a_regulator_driver = {
+	.driver = {
+		.name = "sy7636a-regulator",
+	},
+	.probe = sy7636a_regulator_probe,
+	.id_table = sy7636a_regulator_id_table,
+};
+module_platform_driver(sy7636a_regulator_driver);
+
+MODULE_AUTHOR("Lars Ivar Miljeteig <lars.ivar.miljeteig@remarkable.com>");
+MODULE_DESCRIPTION("SY7636A voltage regulator driver");
+MODULE_LICENSE("GPL v2");
-- 
2.31.1


  parent reply	other threads:[~2021-06-15 10:34 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-06-15 10:33 [PATCH v6 1/5] dt-bindings: mfd: Initial commit of silergy,sy7636a.yaml Alistair Francis
2021-06-15 10:33 ` [PATCH v6 2/5] mfd: sy7636a: Initial commit Alistair Francis
2021-06-16 10:56   ` Lee Jones
2021-06-16 22:01     ` Alistair Francis
2021-06-17  9:20       ` Lee Jones
2021-07-08 11:16         ` Alistair Francis
2021-07-08 12:47           ` Lee Jones
2021-07-28  6:57             ` Alistair Francis
2021-08-02  8:45               ` Lee Jones
2021-06-15 10:33 ` Alistair Francis [this message]
2021-06-15 10:33 ` [PATCH v6 4/5] ARM: imx_v6_v7_defconfig: Enable silergy,sy7636a Alistair Francis
2021-06-15 10:34 ` [PATCH v6 5/5] ARM: dts: imx7d: remarkable2: " Alistair Francis
2021-06-15 17:29 ` (subset) [PATCH v6 1/5] dt-bindings: mfd: Initial commit of silergy,sy7636a.yaml Mark Brown
2021-06-24 20:56 ` Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210615103400.946-3-alistair@alistair23.me \
    --to=alistair@alistair23.me \
    --cc=alistair23@gmail.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=kernel@pengutronix.de \
    --cc=lee.jones@linaro.org \
    --cc=lgirdwood@gmail.com \
    --cc=linux-imx@nxp.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).