linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Bhupesh Sharma <bhupesh.sharma@linaro.org>
To: linux-arm-msm@vger.kernel.org
Cc: bhupesh.sharma@linaro.org, bhupesh.linux@gmail.com,
	linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org,
	devicetree@vger.kernel.org, robh+dt@kernel.org,
	agross@kernel.org, Mark Brown <broonie@kernel.org>,
	Vinod Koul <vkoul@kernel.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>
Subject: [PATCH v3 3/5] arm64: dts: qcom: pmm8155au_1: Add base dts file
Date: Thu, 17 Jun 2021 11:15:46 +0530	[thread overview]
Message-ID: <20210617054548.353293-4-bhupesh.sharma@linaro.org> (raw)
In-Reply-To: <20210617054548.353293-1-bhupesh.sharma@linaro.org>

Add base DTS file for pmm8155au_1 along with GPIOs, power-on, rtc and vadc
nodes.

Cc: Mark Brown <broonie@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
---
 arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi | 134 ++++++++++++++++++++++
 1 file changed, 134 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi

diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi
new file mode 100644
index 000000000000..b04c28e54470
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+/ {
+	thermal-zones {
+		pmm8155au-1-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pmm8155au_1_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmic@0 {
+		compatible = "qcom,pmm8155au", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon: power-on@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x0800>;
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+
+				status = "disabled";
+			};
+		};
+
+		pmm8155au_1_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pmm8155au_1_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmm8155au_1_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+		};
+
+		pmm8155au_1_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pmm8155au_1_rtc: rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+
+			status = "disabled";
+		};
+
+		pmm8155au_1_gpios: gpio@c000 {
+			compatible = "qcom,pmm8155au-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@1 {
+		compatible = "qcom,pmm8155au", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
-- 
2.31.1


  parent reply	other threads:[~2021-06-17  5:46 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-06-17  5:45 [PATCH v3 0/5] arm64: dts: qcom: Add SA8155p-adp board DTS Bhupesh Sharma
2021-06-17  5:45 ` [PATCH v3 1/5] dt-bindings: arm: qcom: Add compatible for sm8150-mtp board Bhupesh Sharma
2021-06-17  5:45 ` [PATCH v3 2/5] dt-bindings: arm: qcom: Add compatible for SA8155p-adp board Bhupesh Sharma
2021-06-17  5:45 ` Bhupesh Sharma [this message]
2021-06-17 22:34   ` [PATCH v3 3/5] arm64: dts: qcom: pmm8155au_1: Add base dts file Konrad Dybcio
2021-06-18  9:58     ` Bhupesh Sharma
2021-06-17  5:45 ` [PATCH v3 4/5] arm64: dts: qcom: pmm8155au_2: " Bhupesh Sharma
2021-06-17 22:32   ` Konrad Dybcio
2021-06-18 10:12     ` Bhupesh Sharma
2021-06-18 17:35     ` Bjorn Andersson
2021-06-17  5:45 ` [PATCH v3 5/5] arm64: dts: qcom: sa8155p-adp: " Bhupesh Sharma
2021-06-17 22:26   ` Konrad Dybcio
2021-06-18  9:56     ` Bhupesh Sharma

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210617054548.353293-4-bhupesh.sharma@linaro.org \
    --to=bhupesh.sharma@linaro.org \
    --cc=agross@kernel.org \
    --cc=bhupesh.linux@gmail.com \
    --cc=bjorn.andersson@linaro.org \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).