[PATCH 0/5] arm64: dts: rockchip: rk3568-evb1-v10: add sd card support

[PATCH 0/5] arm64: dts: rockchip: rk3568-evb1-v10: add sd card support

[Michael Riesch]

Hi all,

This series enables the SD card reader on the RK3568 EVB1
and completes the support for the on-board eMMC.

As the PMU IO domains are required, this depends on the
patch "soc: rockchip: io-domain: add rk3568 support" [1].

Best regards,
Michael

[1] https://patchwork.kernel.org/project/linux-rockchip/patch/20210527072917.1425321-1-jay.xu@rock-chips.com/

Michael Riesch (5):
  arm64: dts: rockchip: rk3568-evb1-v10: add regulators of rk809 pmic
  arm64: dts: rockchip: enable io domains for rk356x
  arm64: dts: rockchip: rk3568-evb1-v10: enable io domains
  arm64: dts: rockchip: rk3568-evb1-v10: add pinctrl and alias to emmc
    node
  arm64: dts: rockchip: rk3568-evb1-v10: add node for sd card

 .../boot/dts/rockchip/rk3568-evb1-v10.dts     | 237 ++++++++++++++++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi      |   5 +
 2 files changed, 242 insertions(+)

-- 
2.17.1

[PATCH 1/5] arm64: dts: rockchip: rk3568-evb1-v10: add regulators of rk809 pmic

[Michael Riesch]

Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
 .../boot/dts/rockchip/rk3568-evb1-v10.dts     | 206 ++++++++++++++++++
 1 file changed, 206 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
index 65e536c78d2e..f682144a1892 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
@@ -104,6 +104,203 @@
 	status = "okay";
 };
 
+&i2c0 {
+	status = "okay";
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_logic";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_gpu";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_npu";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda0v9_image";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda_0v9";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda0v9_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_acodec";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca_1v8";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_image";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_3v3";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
 &mdio0 {
 	rgmii_phy0: ethernet-phy@0 {
 		compatible = "ethernet-phy-ieee802.3-c22";
@@ -124,6 +321,15 @@
 	};
 };
 
+&pinctrl {
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
 &sdhci {
 	bus-width = <8>;
 	max-frequency = <200000000>;
-- 
2.17.1

[PATCH 2/5] arm64: dts: rockchip: enable io domains for rk356x

[Michael Riesch]

Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
 arch/arm64/boot/dts/rockchip/rk356x.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk356x.dtsi b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
index 3e90a8832bb9..834863940eba 100644
--- a/arch/arm64/boot/dts/rockchip/rk356x.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
@@ -203,6 +203,11 @@
 	pmugrf: syscon@fdc20000 {
 		compatible = "rockchip,rk3568-pmugrf", "syscon", "simple-mfd";
 		reg = <0x0 0xfdc20000 0x0 0x10000>;
+
+		pmu_io_domains: io-domains {
+			compatible = "rockchip,rk3568-pmu-io-voltage-domain";
+			status = "disabled";
+		};
 	};
 
 	grf: syscon@fdc60000 {
-- 
2.17.1

[PATCH 3/5] arm64: dts: rockchip: rk3568-evb1-v10: enable io domains

[Michael Riesch]

Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
 arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
index f682144a1892..f3fd4a6813a2 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
@@ -330,6 +330,19 @@
 	};
 };
 
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
 &sdhci {
 	bus-width = <8>;
 	max-frequency = <200000000>;
-- 
2.17.1

[PATCH 4/5] arm64: dts: rockchip: rk3568-evb1-v10: add pinctrl and alias to emmc node

[Michael Riesch]

Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
 arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
index f3fd4a6813a2..3ac70a8183c4 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
@@ -16,6 +16,7 @@
 	aliases {
 		ethernet0 = &gmac0;
 		ethernet1 = &gmac1;
+		emmc = &sdhci;
 	};
 
 	chosen: chosen {
@@ -347,6 +348,8 @@
 	bus-width = <8>;
 	max-frequency = <200000000>;
 	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
 	status = "okay";
 };
 
-- 
2.17.1

[PATCH 5/5] arm64: dts: rockchip: rk3568-evb1-v10: add node for sd card

[Michael Riesch]

Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
 arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
index 3ac70a8183c4..b0f5aa8c979c 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
@@ -17,6 +17,7 @@
 		ethernet0 = &gmac0;
 		ethernet1 = &gmac1;
 		emmc = &sdhci;
+		sd = &sdmmc0;
 	};
 
 	chosen: chosen {
@@ -353,6 +354,20 @@
 	status = "okay";
 };
 
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr104;
+	supports-sd;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
 &uart2 {
 	status = "okay";
 };
-- 
2.17.1

Re: [PATCH 4/5] arm64: dts: rockchip: rk3568-evb1-v10: add pinctrl and alias to emmc node

[Heiko Stübner]

Am Dienstag, 3. August 2021, 20:53:08 CEST schrieb Michael Riesch:
> Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
> ---
>  arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts | 3 +++
>  1 file changed, 3 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
> index f3fd4a6813a2..3ac70a8183c4 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
> @@ -16,6 +16,7 @@
>  	aliases {
>  		ethernet0 = &gmac0;
>  		ethernet1 = &gmac1;
> +		emmc = &sdhci;

what is this supposed to do?

I don't think "emmc" is defined as any form of alias, instead
mmc aliases generally are more "mmcX" for X 0,1,etc .

Heiko

>  	};
>  
>  	chosen: chosen {
> @@ -347,6 +348,8 @@
>  	bus-width = <8>;
>  	max-frequency = <200000000>;
>  	non-removable;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
>  	status = "okay";
>  };
>  
> 

Re: [PATCH 5/5] arm64: dts: rockchip: rk3568-evb1-v10: add node for sd card

[Heiko Stübner]

Am Dienstag, 3. August 2021, 20:53:09 CEST schrieb Michael Riesch:
> Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
> ---
>  arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
> index 3ac70a8183c4..b0f5aa8c979c 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
> @@ -17,6 +17,7 @@
>  		ethernet0 = &gmac0;
>  		ethernet1 = &gmac1;
>  		emmc = &sdhci;
> +		sd = &sdmmc0;

same thing as in the previous patch.

I guess you may want something like

	mmc0 = &sdhci;
	mmc1 = &sdmmc0;

maybe?


Heiko

>  	};
>  
>  	chosen: chosen {
> @@ -353,6 +354,20 @@
>  	status = "okay";
>  };
>  
> +&sdmmc0 {
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
> +	disable-wp;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
> +	sd-uhs-sdr104;
> +	supports-sd;
> +	vmmc-supply = <&vcc3v3_sd>;
> +	vqmmc-supply = <&vccio_sd>;
> +	status = "okay";
> +};
> +
>  &uart2 {
>  	status = "okay";
>  };
> 

Re: [PATCH 5/5] arm64: dts: rockchip: rk3568-evb1-v10: add node for sd card

[Michael Riesch]

Hi Heiko,

On 8/3/21 10:48 PM, Heiko Stübner wrote:
> Am Dienstag, 3. August 2021, 20:53:09 CEST schrieb Michael Riesch:
>> Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
>> ---
>>  arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts | 15 +++++++++++++++
>>  1 file changed, 15 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
>> index 3ac70a8183c4..b0f5aa8c979c 100644
>> --- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
>> +++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
>> @@ -17,6 +17,7 @@
>>  		ethernet0 = &gmac0;
>>  		ethernet1 = &gmac1;
>>  		emmc = &sdhci;
>> +		sd = &sdmmc0;
> 
> same thing as in the previous patch.
> 
> I guess you may want something like
> 
> 	mmc0 = &sdhci;
> 	mmc1 = &sdmmc0;
> 
> maybe?

Thanks for the suggestion, I'll include it in the v2.

Regards, Michael

> 
> 
> Heiko
> 
>>  	};
>>  
>>  	chosen: chosen {
>> @@ -353,6 +354,20 @@
>>  	status = "okay";
>>  };
>>  
>> +&sdmmc0 {
>> +	bus-width = <4>;
>> +	cap-sd-highspeed;
>> +	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
>> +	disable-wp;
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
>> +	sd-uhs-sdr104;
>> +	supports-sd;
>> +	vmmc-supply = <&vcc3v3_sd>;
>> +	vqmmc-supply = <&vccio_sd>;
>> +	status = "okay";
>> +};
>> +
>>  &uart2 {
>>  	status = "okay";
>>  };
>>
> 
> 
> 
>