From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Rob Herring <robh+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Alexey Minnekhanov <alexeymin@postmarketos.org>,
AngeloGioacchino Del Regno
<angelogioacchino.delregno@somainline.org>
Subject: [PATCH v2] arm64: dts: qcom: sdm660: Add initial IFC6560 board
Date: Wed, 25 Aug 2021 15:11:10 -0700 [thread overview]
Message-ID: <20210825221110.1498718-1-bjorn.andersson@linaro.org> (raw)
The IFC6560 is a board from Inforce Computing, built around the SDA660
SoC. This patch describes core clocks, some regulators from the two
PMICs, debug uart, storage, bluetooth and audio DSP remoteproc.
The regulator settings are inherited from prior work by Konrad Dybcio
and AngeloGioacchino Del Regno.
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
Changes since v1:
- Fixed typo 29p5 -> 2p95 in two regulators.
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts | 279 ++++++++++++++++++++
2 files changed, 280 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 70516508be56..88abcfeb4d38 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -73,6 +73,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-discovery.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-pioneer.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-voyager.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm636-sony-xperia-ganges-mermaid.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm660-ifc6560.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm660-xiaomi-lavender.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts b/arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts
new file mode 100644
index 000000000000..bfb17711ab55
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts
@@ -0,0 +1,279 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Ltd.
+ * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org>
+ * Copyright (c) 2020, AngeloGioacchino Del Regno
+ * <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "sdm660.dtsi"
+#include "pm660.dtsi"
+#include "pm660l.dtsi"
+
+/ {
+ model = "Inforce 6560 Single Board Computer";
+ compatible = "inforce,ifc6560", "qcom,sdm660";
+
+ aliases {
+ serial0 = &blsp1_uart2;
+ serial1 = &blsp2_uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ };
+
+ v3p3_bck_bst: v3p3-bck-bst-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "v3p3_bck_bst";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ vin-supply = <&vph_pwr>;
+ };
+
+ v1p2_ldo: v1p2-ldo-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "v1p2_ldo";
+
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ vin-supply = <&vph_pwr>;
+ };
+
+ v5p0_boost: v5p0-boost-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "v5p0_boost";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ vin-supply = <&vph_pwr>;
+ };
+};
+
+&adsp_pil {
+ firmware-name = "qcom/inforce/ifc6560/adsp.mbn";
+};
+
+&blsp1_uart2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart_active>;
+};
+
+&blsp2_uart1 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3990-bt";
+
+ vddio-supply = <&vreg_l13a_1p8>;
+ vddxo-supply = <&vreg_l9a_1p8>;
+ vddrf-supply = <&vreg_l6a_1p3>;
+ vddch0-supply = <&vreg_l19a_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&rpm_requests {
+ pm660-regulators {
+ compatible = "qcom,rpm-pm660-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+ vdd_s2-supply = <&vph_pwr>;
+ vdd_s3-supply = <&vph_pwr>;
+ vdd_s4-supply = <&vph_pwr>;
+ vdd_s5-supply = <&vph_pwr>;
+ vdd_s6-supply = <&vph_pwr>;
+
+ vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>;
+ vdd_l2_l3-supply = <&vreg_s2b_1p05>;
+ vdd_l5-supply = <&vreg_s2b_1p05>;
+ vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>;
+ vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>;
+
+ vreg_s4a_2p04: s4 {
+ regulator-min-microvolt = <2040000>;
+ regulator-max-microvolt = <2040000>;
+ regulator-enable-ramp-delay = <200>;
+ regulator-ramp-delay = <0>;
+ regulator-always-on;
+ };
+
+ vreg_s5a_1p35: s5 {
+ regulator-min-microvolt = <1224000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-enable-ramp-delay = <200>;
+ regulator-ramp-delay = <0>;
+ };
+
+ vreg_l6a_1p3: l6 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1368000>;
+ regulator-allow-set-load;
+ regulator-enable-ramp-delay = <250>;
+ regulator-ramp-delay = <0>;
+ };
+
+ vreg_l8a_1p8: l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <250>;
+ regulator-ramp-delay = <0>;
+ regulator-system-load = <325000>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l9a_1p8: l9 {
+ regulator-min-microvolt = <1804000>;
+ regulator-max-microvolt = <1896000>;
+ regulator-enable-ramp-delay = <250>;
+ regulator-ramp-delay = <0>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l13a_1p8: l13 {
+ /* This gives power to the LPDDR4: never turn it off! */
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1944000>;
+ regulator-enable-ramp-delay = <250>;
+ regulator-ramp-delay = <0>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_l19a_3p3: l19 {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-enable-ramp-delay = <250>;
+ regulator-ramp-delay = <0>;
+ regulator-allow-set-load;
+ };
+ };
+
+ pm660l-regulators {
+ compatible = "qcom,rpm-pm660l-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+ vdd_s2-supply = <&vph_pwr>;
+ vdd_s3_s4-supply = <&vph_pwr>;
+ vdd_s5-supply = <&vph_pwr>;
+ vdd_s6-supply = <&vph_pwr>;
+
+ vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>;
+ vdd_l2-supply = <&vreg_bob>;
+ vdd_l3_l5_l7_l8-supply = <&vreg_bob>;
+ vdd_l4_l6-supply = <&vreg_bob>;
+ vdd_bob-supply = <&vph_pwr>;
+
+ vreg_s2b_1p05: s2 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-enable-ramp-delay = <200>;
+ regulator-ramp-delay = <0>;
+ };
+
+ vreg_l2b_2p95: l2 {
+ /*
+ * This regulator supports 1.648 - 3.104V on this board
+ * but we set a max voltage of anything less than 2.7V
+ * to satisfy a condition in sdhci.c that will disable
+ * 3.3V SDHCI signaling, which happens to be not really
+ * supported on the Xperia Nile/Ganges platform.
+ */
+ regulator-min-microvolt = <1648000>;
+ regulator-max-microvolt = <2696000>;
+ regulator-enable-ramp-delay = <250>;
+ regulator-ramp-delay = <0>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l4b_2p95: l4 {
+ regulator-min-microvolt = <2944000>;
+ regulator-max-microvolt = <2952000>;
+ regulator-enable-ramp-delay = <250>;
+ regulator-ramp-delay = <0>;
+
+ regulator-min-microamp = <200>;
+ regulator-max-microamp = <600000>;
+ regulator-system-load = <570000>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l5b_2p95: l5 {
+ /*
+ * Downstream specifies a range of 1721-3600mV,
+ * but the only assigned consumers are SDHCI2 VMMC
+ * and Coresight QPDI that both request pinned 2.95V.
+ * Tighten the range to 1.8-3.328 (closest to 3.3) to
+ * make the mmc driver happy.
+ */
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3328000>;
+ regulator-enable-ramp-delay = <250>;
+ regulator-ramp-delay = <0>;
+ regulator-allow-set-load;
+ regulator-system-load = <800000>;
+ };
+
+ vreg_l8b_3p3: l8 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-enable-ramp-delay = <250>;
+ regulator-ramp-delay = <0>;
+ };
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3304000>;
+ regulator-max-microvolt = <3624000>;
+ regulator-enable-ramp-delay = <500>;
+ regulator-ramp-delay = <0>;
+ };
+ };
+};
+
+&sdhc_1 {
+ status = "okay";
+ supports-cqe;
+
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+
+ vmmc-supply = <&vreg_l4b_2p95>;
+ vqmmc-supply = <&vreg_l8a_1p8>;
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ vmmc-supply = <&vreg_l5b_2p95>;
+ vqmmc-supply = <&vreg_l2b_2p95>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <8 4>;
+
+ uart_active: uart-active-state {
+ pins = "gpio4", "gpio5";
+ function = "blsp_uart2";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
--
2.29.2
next reply other threads:[~2021-08-25 22:10 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-08-25 22:11 Bjorn Andersson [this message]
2021-08-27 23:05 ` [PATCH v2] arm64: dts: qcom: sdm660: Add initial IFC6560 board Konrad Dybcio
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210825221110.1498718-1-bjorn.andersson@linaro.org \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=alexeymin@postmarketos.org \
--cc=angelogioacchino.delregno@somainline.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).