From: Jonathan Cameron <jic23@kernel.org>
To: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
linux-iio@vger.kernel.org, <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 03/16] iio: adc: max1027: Push only the requested samples
Date: Mon, 30 Aug 2021 11:06:16 +0100 [thread overview]
Message-ID: <20210830110616.70672ef3@jic23-huawei> (raw)
In-Reply-To: <20210818111139.330636-4-miquel.raynal@bootlin.com>
On Wed, 18 Aug 2021 13:11:26 +0200
Miquel Raynal <miquel.raynal@bootlin.com> wrote:
> When a triggered scan occurs, the identity of the desired channels is
> known in indio_dev->active_scan_mask. Instead of reading and pushing to
> the IIO buffers all channels each time, scan the minimum amount of
> channels (0 to maximum requested chan, to be exact) and only provide the
> samples requested by the user.
>
> For example, if the user wants channels 1, 4 and 5, all channels from
> 0 to 5 will be scanned
That's a reasonably optimisation
> but only the desired channels will be pushed to
> the IIO buffers.
Don't do this last bit. The core handles demuxing the channels via
active_scan_masks. As a general rule it does a more efficient job of this
than a hand coded version in a driver (precached copy rules etc).
The core has to have the logic anyway to support multiple consumers
(e.g. in kernel consumer and userspace) so we reuse it for these cases.
>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
> drivers/iio/adc/max1027.c | 25 +++++++++++++++++++++----
> 1 file changed, 21 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/iio/adc/max1027.c b/drivers/iio/adc/max1027.c
> index b753658bb41e..8ab660f596b5 100644
> --- a/drivers/iio/adc/max1027.c
> +++ b/drivers/iio/adc/max1027.c
> @@ -360,6 +360,9 @@ static int max1027_set_trigger_state(struct iio_trigger *trig, bool state)
> struct max1027_state *st = iio_priv(indio_dev);
> int ret;
>
> + if (bitmap_empty(indio_dev->active_scan_mask, indio_dev->masklength))
> + return -EINVAL;
> +
> if (state) {
> /* Start acquisition on cnvst */
> st->reg = MAX1027_SETUP_REG | MAX1027_CKS_MODE0 |
> @@ -368,9 +371,12 @@ static int max1027_set_trigger_state(struct iio_trigger *trig, bool state)
> if (ret < 0)
> return ret;
>
> - /* Scan from 0 to max */
> - st->reg = MAX1027_CONV_REG | MAX1027_CHAN(0) |
> - MAX1027_SCAN_N_M | MAX1027_TEMP;
> + /*
> + * Scan from 0 to the highest requested channel. The temperature
> + * could be avoided but it simplifies a bit the logic.
> + */
> + st->reg = MAX1027_CONV_REG | MAX1027_SCAN_0_N | MAX1027_TEMP;
> + st->reg |= MAX1027_CHAN(fls(*indio_dev->active_scan_mask) - 2);
This should be combined with appropriate additions to available_scan_masks arrays
so the IIO core can handle choosing the right one to match enabled channels.
> ret = spi_write(st->spi, &st->reg, 1);
> if (ret < 0)
> return ret;
> @@ -391,11 +397,22 @@ static irqreturn_t max1027_trigger_handler(int irq, void *private)
> struct iio_poll_func *pf = private;
> struct iio_dev *indio_dev = pf->indio_dev;
> struct max1027_state *st = iio_priv(indio_dev);
> + unsigned int scanned_chans = fls(*indio_dev->active_scan_mask);
> + u16 *buf = st->buffer;
> + unsigned int bit;
>
> pr_debug("%s(irq=%d, private=0x%p)\n", __func__, irq, private);
>
> /* fill buffer with all channel */
> - spi_read(st->spi, st->buffer, indio_dev->masklength * 2);
> + spi_read(st->spi, st->buffer, scanned_chans * 2);
> +
> + /* Only keep the channels selected by the user */
> + for_each_set_bit(bit, indio_dev->active_scan_mask,
> + indio_dev->masklength) {
> + if (buf[0] != st->buffer[bit])
> + buf[0] = st->buffer[bit];
> + buf++;
> + }
>
> iio_push_to_buffers(indio_dev, st->buffer);
>
next prev parent reply other threads:[~2021-08-30 10:03 UTC|newest]
Thread overview: 71+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-08-18 11:11 [PATCH 00/16] Bring software triggers support to MAX1027-like ADCs Miquel Raynal
2021-08-18 11:11 ` [PATCH 01/16] iio: adc: max1027: Fix wrong shift with 12-bit devices Miquel Raynal
2021-08-20 7:02 ` Sa, Nuno
2021-08-30 9:57 ` Jonathan Cameron
2021-08-18 11:11 ` [PATCH 02/16] iio: adc: max1027: Fix the number of max1X31 channels Miquel Raynal
2021-08-20 7:03 ` Sa, Nuno
2021-08-30 10:00 ` Jonathan Cameron
2021-08-18 11:11 ` [PATCH 03/16] iio: adc: max1027: Push only the requested samples Miquel Raynal
2021-08-20 7:10 ` Sa, Nuno
2021-08-30 10:07 ` Jonathan Cameron
2021-08-30 10:49 ` Sa, Nuno
2021-08-30 14:29 ` Jonathan Cameron
2021-08-30 15:02 ` Sa, Nuno
2021-09-01 8:12 ` Miquel Raynal
2021-09-04 14:06 ` Jonathan Cameron
2021-09-06 8:59 ` Sa, Nuno
2021-09-06 16:56 ` Jonathan Cameron
2021-09-06 17:34 ` Miquel Raynal
2021-08-30 10:06 ` Jonathan Cameron [this message]
2021-08-18 11:11 ` [PATCH 04/16] iio: adc: max1027: Lower conversion time Miquel Raynal
2021-08-20 7:12 ` Sa, Nuno
2021-08-30 10:10 ` Jonathan Cameron
2021-08-18 11:11 ` [PATCH 05/16] iio: adc: max1027: Drop extra warning message Miquel Raynal
2021-08-20 7:12 ` Sa, Nuno
2021-08-30 10:12 ` Jonathan Cameron
2021-08-18 11:11 ` [PATCH 06/16] iio: adc: max1027: Rename a helper Miquel Raynal
2021-08-20 7:13 ` Sa, Nuno
2021-08-18 11:11 ` [PATCH 07/16] iio: adc: max1027: Create a helper to configure the trigger Miquel Raynal
2021-08-20 7:16 ` Sa, Nuno
2021-08-30 10:16 ` Jonathan Cameron
2021-08-18 11:11 ` [PATCH 08/16] iio: adc: max1027: Explain better how the trigger state gets changed Miquel Raynal
2021-08-20 7:17 ` Sa, Nuno
2021-08-18 11:11 ` [PATCH 09/16] iio: adc: max1027: Create a helper to configure the channels to scan Miquel Raynal
2021-08-20 7:18 ` Sa, Nuno
2021-08-18 11:11 ` [PATCH 10/16] iio: adc: max1027: Prevent single channel accesses during buffer reads Miquel Raynal
2021-08-20 7:20 ` Sa, Nuno
2021-08-20 7:30 ` Sa, Nuno
2021-08-30 10:20 ` Jonathan Cameron
2021-09-02 8:56 ` Miquel Raynal
2021-08-18 11:11 ` [PATCH 11/16] iio: adc: max1027: Separate the IRQ handler from the read logic Miquel Raynal
2021-08-20 7:23 ` Sa, Nuno
2021-09-02 8:55 ` Miquel Raynal
2021-09-04 14:08 ` Jonathan Cameron
2021-08-18 11:11 ` [PATCH 12/16] iio: adc: max1027: Introduce an end of conversion helper Miquel Raynal
2021-08-20 7:28 ` Sa, Nuno
2021-09-02 9:26 ` Miquel Raynal
2021-08-30 10:34 ` Jonathan Cameron
2021-08-18 11:11 ` [PATCH 13/16] iio: adc: max1027: Prepare re-using the EOC interrupt Miquel Raynal
2021-08-20 7:31 ` Sa, Nuno
2021-08-30 10:30 ` Jonathan Cameron
2021-08-30 10:47 ` Jonathan Cameron
2021-08-18 11:11 ` [PATCH 14/16] iio: adc: max1027: Consolidate the end of conversion helper Miquel Raynal
2021-08-20 7:45 ` Sa, Nuno
2021-08-30 10:37 ` Jonathan Cameron
2021-08-30 12:44 ` Sa, Nuno
2021-08-30 14:32 ` Jonathan Cameron
2021-09-02 15:12 ` Miquel Raynal
2021-09-03 14:28 ` Sa, Nuno
2021-09-03 14:46 ` Miquel Raynal
2021-09-05 9:41 ` Jonathan Cameron
2021-09-06 9:12 ` Sa, Nuno
2021-09-06 9:30 ` Sa, Nuno
2021-08-18 11:11 ` [PATCH 15/16] iio: adc: max1027: Support software triggers Miquel Raynal
2021-08-20 7:58 ` Sa, Nuno
2021-09-02 12:25 ` Miquel Raynal
2021-09-03 14:20 ` Sa, Nuno
2021-08-30 10:50 ` Jonathan Cameron
2021-09-02 15:21 ` Miquel Raynal
2021-09-05 9:43 ` Jonathan Cameron
2021-08-18 11:11 ` [PATCH 16/16] iio: adc: max1027: Enable software triggers to be used without IRQ Miquel Raynal
2021-08-30 10:54 ` Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210830110616.70672ef3@jic23-huawei \
--to=jic23@kernel.org \
--cc=lars@metafoo.de \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=miquel.raynal@bootlin.com \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).