[5.16][PATCH 3/3] MIPS: JZ4780: CI20: DTS: add SPI controller config

[Artur Rojek <contact@artur-rojek.eu>]

1. Add nodes for the two SPI controllers found in MIPS Creator CI20.
2. Reparent SPI clock source to effectively use MPLL and set its clock
   rate to 54MHz.

NOTE: To use the SPI controllers, `pinctrl-0` property must be set in
order to configure the used pins. As SPI functionality is multiplexed on
multiple pin groups, this choice is left to the user.

An example configuration:
```
 &spi0 {
         pinctrl-0 = <&pins_spi0>;
 }

 pins_spi0: spi0 {
         function = "ssi0";
         groups = "ssi0-dt-e", "ssi0-dr-e", "ssi0-clk-e",
                  "ssi0-ce0-e", "ssi0-ce1-e";
         bias-disable;
 };
```
Consult the CI20 pinout description for more details.

Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
---
 arch/mips/boot/dts/ingenic/ci20.dts    |  9 ++++--
 arch/mips/boot/dts/ingenic/jz4780.dtsi | 44 +++++++++++++++++++-------
 2 files changed, 38 insertions(+), 15 deletions(-)

diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
index a688809beebc..b249a4f0f6b6 100644
--- a/arch/mips/boot/dts/ingenic/ci20.dts
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -113,9 +113,12 @@ &cgu {
 	 * Use the 32.768 kHz oscillator as the parent of the RTC for a higher
 	 * precision.
 	 */
-	assigned-clocks = <&cgu JZ4780_CLK_OTGPHY>, <&cgu JZ4780_CLK_RTC>;
-	assigned-clock-parents = <0>, <&cgu JZ4780_CLK_RTCLK>;
-	assigned-clock-rates = <48000000>;
+	assigned-clocks = <&cgu JZ4780_CLK_OTGPHY>, <&cgu JZ4780_CLK_RTC>,
+			  <&cgu JZ4780_CLK_SSIPLL>, <&cgu JZ4780_CLK_SSI>;
+	assigned-clock-parents = <0>, <&cgu JZ4780_CLK_RTCLK>,
+				 <&cgu JZ4780_CLK_MPLL>,
+				 <&cgu JZ4780_CLK_SSIPLL>;
+	assigned-clock-rates = <48000000>, <0>, <54000000>;
 };
 
 &tcu {
diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
index 9e34f433b9b5..28adc3d93975 100644
--- a/arch/mips/boot/dts/ingenic/jz4780.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
@@ -255,22 +255,23 @@ gpf: gpio@5 {
 		};
 	};
 
-	spi_gpio {
-		compatible = "spi-gpio";
+	spi0: spi@10043000 {
+		compatible = "ingenic,jz4780-spi";
+		reg = <0x10043000 0x1c>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		num-chipselects = <2>;
 
-		gpio-miso = <&gpe 14 0>;
-		gpio-sck = <&gpe 15 0>;
-		gpio-mosi = <&gpe 17 0>;
-		cs-gpios = <&gpe 16 0>, <&gpe 18 0>;
+		interrupt-parent = <&intc>;
+		interrupts = <8>;
 
-		spidev@0 {
-			compatible = "spidev";
-			reg = <0>;
-			spi-max-frequency = <1000000>;
-		};
+		clocks = <&cgu JZ4780_CLK_SSI0>;
+		clock-names = "spi";
+
+		dmas = <&dma JZ4780_DMA_SSI0_RX 0xffffffff>,
+		       <&dma JZ4780_DMA_SSI0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
 	};
 
 	uart0: serial@10030000 {
@@ -338,6 +339,25 @@ uart4: serial@10034000 {
 		status = "disabled";
 	};
 
+	spi1: spi@10044000 {
+		compatible = "ingenic,jz4780-spi";
+		reg = <0x10044000 0x1c>;
+		#address-cells = <1>;
+		#size-sells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <7>;
+
+		clocks = <&cgu JZ4780_CLK_SSI1>;
+		clock-names = "spi";
+
+		dmas = <&dma JZ4780_DMA_SSI1_RX 0xffffffff>,
+		       <&dma JZ4780_DMA_SSI1_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
 	i2c0: i2c@10050000 {
 		compatible = "ingenic,jz4780-i2c", "ingenic,jz4770-i2c";
 		#address-cells = <1>;
-- 
2.33.0