Re: [PATCH devicetree 2/2] arm64: dts: add device tree for the LX2160A on the NXP BlueBox3 board

[Shawn Guo <shawnguo@kernel.org>]

On Fri, Aug 27, 2021 at 11:27:22PM +0300, Vladimir Oltean wrote:
> From: Wasim Khan <wasim.khan@nxp.com>
> 
> The NXP BlueBox3 is a prototyping board for high-performance autonomous
> driving systems. It contains two Linux systems, on running on the

s/on running/running

> LX2160A and the other on the S32G2 SoC. This patch adds the device tree
> support for the LX2160A SoC.
> 
> In terms of networking from the LX2160A's perspective, there are:
> 
> - 4 RJ45 10G ports using Aquantia copper PHYs which are attached
>   directly to DPAA2 ports on the LX2160A
> 
> - 3 NXP SJA1110 automotive Ethernet switches. First two are managed by
>   the LX2160A (each switch has a host port towards a dpmac), the third
>   switch is managed by the S32G2. All 3 switches are interconnected
>   through on-board SERDES lanes. The cascade ports between the 2
>   switches managed by LX2160A form a DSA link, the cascade ports between
>   the LX2160A and the S32G2 domain form user ports (the "to_sw3" net
>   device).
> 
> - 2 RJ45 1G ports using Atheros copper PHYs which are attached directly
>   to NXP SJA1110 switches
> 
> - 12 automotive 100base-T1 single-pair Ethernet ports routed from the
>   SJA1110 internal PHY ports (TJA1103)
> 
> - One SGMII SERDES lane towards an internal connector, attached to one
>   of the SJA1110 switch ports
> 
> On board rev A, the AR8035 RGMII PHY addresses were different than on
> rev B and later. This patch introduces a separate device tree for rev A.
> The main device tree is supposed to cover rev B and later.
> 
> Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
> Co-developed-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Co-developed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> Co-developed-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
> Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
> Co-developed-by: Biwen Li <biwen.li@nxp.com>
> Signed-off-by: Biwen Li <biwen.li@nxp.com>
> Co-developed-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
> Signed-off-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
> Co-developed-by: Yangbo Lu <yangbo.lu@nxp.com>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
> Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> ---
>  arch/arm64/boot/dts/freescale/Makefile        |   2 +
>  .../freescale/fsl-lx2160a-bluebox3-rev-a.dts  |  34 +
>  .../dts/freescale/fsl-lx2160a-bluebox3.dts    | 658 ++++++++++++++++++
>  3 files changed, 694 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index db9e36ebe932..ecf74464705f 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -25,6 +25,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
>  dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> new file mode 100644
> index 000000000000..15d273c93154
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> @@ -0,0 +1,34 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160A BLUEBOX3
> +//
> +// Copyright 2020-2021 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a-bluebox3.dts"
> +
> +/ {
> +	compatible = "fsl,lx2160a-bluebox3-rev-a", "fsl,lx2160a";
> +};
> +
> +/* The RGMII PHYs have a different MDIO address */
> +&emdio1 {
> +	/delete-node/ ethernet-phy@5;
> +
> +	sw1_mii3_phy: ethernet-phy@1 {
> +		/* AR8035 */
> +		compatible = "ethernet-phy-id004d.d072";
> +		reg = <0x1>;
> +		interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +
> +	/delete-node/ ethernet-phy@6;
> +
> +	sw2_mii3_phy: ethernet-phy@2 {
> +		/* AR8035 */
> +		compatible = "ethernet-phy-id004d.d072";
> +		reg = <0x2>;
> +		interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> new file mode 100644
> index 000000000000..be7d01630a6f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> @@ -0,0 +1,658 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160A BLUEBOX3
> +//
> +// Copyright 2020-2021 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a.dtsi"
> +
> +/ {
> +	model = "NXP Layerscape LX2160ABLUEBOX3";
> +	compatible = "fsl,lx2160a-bluebox3", "fsl,lx2160a";
> +
> +	aliases {
> +		crypto = &crypto;
> +		serial0 = &uart0;
> +		mmc0 = &esdhc0;
> +		mmc1 = &esdhc1;

It's nice to have them sort alphabetically.

I fixed them up and applied the patch.

Shawn

> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	sb_3v3: regulator-sb3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "MC34717-3.3VSB";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +};
> +
> +&can0 {
> +	status = "okay";
> +
> +	can-transceiver {
> +		max-bitrate = <5000000>;
> +	};
> +};
> +
> +&can1 {
> +	status = "okay";
> +
> +	can-transceiver {
> +		max-bitrate = <5000000>;
> +	};
> +};
> +
> +&crypto {
> +	status = "okay";
> +};
> +
> +&dpmac5 {
> +	phy-handle = <&aqr113c_phy1>;
> +	phy-mode = "usxgmii";
> +	managed = "in-band-status";
> +};
> +
> +&dpmac6 {
> +	phy-handle = <&aqr113c_phy2>;
> +	phy-mode = "usxgmii";
> +	managed = "in-band-status";
> +};
> +
> +&dpmac9 {
> +	phy-handle = <&aqr113c_phy3>;
> +	phy-mode = "usxgmii";
> +	managed = "in-band-status";
> +};
> +
> +&dpmac10 {
> +	phy-handle = <&aqr113c_phy4>;
> +	phy-mode = "usxgmii";
> +	managed = "in-band-status";
> +};
> +
> +&dpmac17 {
> +	phy-mode = "rgmii";
> +	status = "okay";
> +
> +	fixed-link {
> +		speed = <1000>;
> +		full-duplex;
> +	};
> +};
> +
> +&dpmac18 {
> +	phy-mode = "rgmii";
> +	status = "okay";
> +
> +	fixed-link {
> +		speed = <1000>;
> +		full-duplex;
> +	};
> +};
> +
> +&emdio1 {
> +	status = "okay";
> +
> +	aqr113c_phy2: ethernet-phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		reg = <0x0>;
> +		/* IRQ_10G_PHY2 */
> +		interrupts-extended = <&extirq 3 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +
> +	aqr113c_phy1: ethernet-phy@8 {
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		reg = <0x8>;
> +		/* IRQ_10G_PHY1 */
> +		interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +
> +	sw1_mii3_phy: ethernet-phy@5 {
> +		/* AR8035 */
> +		compatible = "ethernet-phy-id004d.d072";
> +		reg = <0x5>;
> +		interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +
> +	sw2_mii3_phy: ethernet-phy@6 {
> +		/* AR8035 */
> +		compatible = "ethernet-phy-id004d.d072";
> +		reg = <0x6>;
> +		interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +};
> +
> +&emdio2 {
> +	status = "okay";
> +
> +	aqr113c_phy4: ethernet-phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		reg = <0x0>;
> +		/* IRQ_10G_PHY4 */
> +		interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +
> +	aqr113c_phy3: ethernet-phy@8 {
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		reg = <0x8>;
> +		/* IRQ_10G_PHY3 */
> +		interrupts-extended = <&extirq 4 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +};
> +
> +&esdhc0 {
> +	sd-uhs-sdr104;
> +	sd-uhs-sdr50;
> +	sd-uhs-sdr25;
> +	sd-uhs-sdr12;
> +	status = "okay";
> +};
> +
> +&esdhc1 {
> +	mmc-hs200-1_8v;
> +	mmc-hs400-1_8v;
> +	bus-width = <8>;
> +	status = "okay";
> +};
> +
> +&fspi {
> +	status = "okay";
> +
> +	mt35xu512aba0: flash@0 {
> +		compatible = "jedec,spi-nor";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		reg = <0>;
> +		m25p,fast-read;
> +		spi-max-frequency = <50000000>;
> +		spi-rx-bus-width = <8>;
> +		spi-tx-bus-width = <8>;
> +	};
> +
> +	mt35xu512aba1: flash@1 {
> +		compatible = "jedec,spi-nor";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		reg = <1>;
> +		m25p,fast-read;
> +		spi-max-frequency = <50000000>;
> +		spi-rx-bus-width = <8>;
> +		spi-tx-bus-width = <8>;
> +	};
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	i2c-mux@77 {
> +		compatible = "nxp,pca9547";
> +		reg = <0x77>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		i2c@2 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x2>;
> +
> +			power-monitor@40 {
> +				compatible = "ti,ina220";
> +				reg = <0x40>;
> +				shunt-resistor = <500>;
> +			};
> +		};
> +
> +		i2c@3 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x3>;
> +
> +			temp2: temperature-sensor@48 {
> +				compatible = "nxp,sa56004";
> +				reg = <0x48>;
> +				vcc-supply = <&sb_3v3>;
> +				#thermal-sensor-cells = <1>;
> +			};
> +
> +			temp1: temperature-sensor@4c {
> +				compatible = "nxp,sa56004";
> +				reg = <0x4c>;
> +				vcc-supply = <&sb_3v3>;
> +				#thermal-sensor-cells = <1>;
> +			};
> +		};
> +
> +		i2c@4 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x4>;
> +
> +			rtc@51 {
> +				compatible = "nxp,pcf2129";
> +				reg = <0x51>;
> +				interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>;
> +			};
> +		};
> +
> +		i2c@7 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x7>;
> +
> +			i2c-mux@75 {
> +				compatible = "nxp,pca9547";
> +				reg = <0x75>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				i2c@0 {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +					reg = <0x0>;
> +
> +					spi_bridge: spi@28 {
> +						compatible = "nxp,sc18is602b";
> +						reg = <0x28>;
> +						#address-cells = <1>;
> +						#size-cells = <0>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&i2c5 {
> +	status = "okay";
> +
> +	i2c-mux@77 {
> +		compatible = "nxp,pca9846";
> +		reg = <0x77>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		i2c@1 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x1>;
> +
> +			/* The I2C multiplexer and temperature sensors are on
> +			 * the T6 riser card.
> +			 */
> +			i2c-mux@70 {
> +				compatible = "nxp,pca9548";
> +				reg = <0x70>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				i2c@6 {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +					reg = <0x6>;
> +
> +					q12: temperature-sensor@4c {
> +						compatible = "nxp,sa56004";
> +						reg = <0x4c>;
> +						vcc-supply = <&sb_3v3>;
> +						#thermal-sensor-cells = <1>;
> +					};
> +				};
> +
> +				i2c@7 {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +					reg = <0x7>;
> +
> +					q11: temperature-sensor@4c {
> +						compatible = "nxp,sa56004";
> +						reg = <0x4c>;
> +						vcc-supply = <&sb_3v3>;
> +						#thermal-sensor-cells = <1>;
> +					};
> +
> +					q13: temperature-sensor@48 {
> +						compatible = "nxp,sa56004";
> +						reg = <0x48>;
> +						vcc-supply = <&sb_3v3>;
> +						#thermal-sensor-cells = <1>;
> +					};
> +
> +					q14: temperature-sensor@4a {
> +						compatible = "nxp,sa56004";
> +						reg = <0x4a>;
> +						vcc-supply = <&sb_3v3>;
> +						#thermal-sensor-cells = <1>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&pcs_mdio5 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio6 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio9 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio10 {
> +	status = "okay";
> +};
> +
> +&spi_bridge {
> +	sw1: ethernet-switch@0 {
> +		compatible = "nxp,sja1110a";
> +		reg = <0>;
> +		spi-max-frequency = <4000000>;
> +		spi-cpol;
> +		dsa,member = <0 0>;
> +
> +		ethernet-ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			/* Microcontroller port */
> +			port@0 {
> +				reg = <0>;
> +				status = "disabled";
> +			};
> +
> +			/* SW1_P1 */
> +			port@1 {
> +				reg = <1>;
> +				label = "con_2x20";
> +				phy-mode = "sgmii";
> +
> +				fixed-link {
> +					speed = <1000>;
> +					full-duplex;
> +				};
> +			};
> +
> +			port@2 {
> +				reg = <2>;
> +				ethernet = <&dpmac17>;
> +				phy-mode = "rgmii-id";
> +
> +				fixed-link {
> +					speed = <1000>;
> +					full-duplex;
> +				};
> +			};
> +
> +			port@3 {
> +				reg = <3>;
> +				label = "1ge_p1";
> +				phy-mode = "rgmii-id";
> +				phy-handle = <&sw1_mii3_phy>;
> +			};
> +
> +			sw1p4: port@4 {
> +				reg = <4>;
> +				link = <&sw2p1>;
> +				phy-mode = "sgmii";
> +
> +				fixed-link {
> +					speed = <1000>;
> +					full-duplex;
> +				};
> +			};
> +
> +			port@5 {
> +				reg = <5>;
> +				label = "trx1";
> +				phy-mode = "internal";
> +				phy-handle = <&sw1_port5_base_t1_phy>;
> +			};
> +
> +			port@6 {
> +				reg = <6>;
> +				label = "trx2";
> +				phy-mode = "internal";
> +				phy-handle = <&sw1_port6_base_t1_phy>;
> +			};
> +
> +			port@7 {
> +				reg = <7>;
> +				label = "trx3";
> +				phy-mode = "internal";
> +				phy-handle = <&sw1_port7_base_t1_phy>;
> +			};
> +
> +			port@8 {
> +				reg = <8>;
> +				label = "trx4";
> +				phy-mode = "internal";
> +				phy-handle = <&sw1_port8_base_t1_phy>;
> +			};
> +
> +			port@9 {
> +				reg = <9>;
> +				label = "trx5";
> +				phy-mode = "internal";
> +				phy-handle = <&sw1_port9_base_t1_phy>;
> +			};
> +
> +			port@a {
> +				reg = <10>;
> +				label = "trx6";
> +				phy-mode = "internal";
> +				phy-handle = <&sw1_port10_base_t1_phy>;
> +			};
> +		};
> +
> +		mdios {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			mdio@0 {
> +				compatible = "nxp,sja1110-base-t1-mdio";
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				reg = <0>;
> +
> +				sw1_port5_base_t1_phy: ethernet-phy@1 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x1>;
> +				};
> +
> +				sw1_port6_base_t1_phy: ethernet-phy@2 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x2>;
> +				};
> +
> +				sw1_port7_base_t1_phy: ethernet-phy@3 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x3>;
> +				};
> +
> +				sw1_port8_base_t1_phy: ethernet-phy@4 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x4>;
> +				};
> +
> +				sw1_port9_base_t1_phy: ethernet-phy@5 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x5>;
> +				};
> +
> +				sw1_port10_base_t1_phy: ethernet-phy@6 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x6>;
> +				};
> +			};
> +		};
> +	};
> +
> +	sw2: ethernet-switch@2 {
> +		compatible = "nxp,sja1110a";
> +		reg = <2>;
> +		spi-max-frequency = <4000000>;
> +		spi-cpol;
> +		dsa,member = <0 1>;
> +
> +		ethernet-ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			/* Microcontroller port */
> +			port@0 {
> +				reg = <0>;
> +				status = "disabled";
> +			};
> +
> +			sw2p1: port@1 {
> +				reg = <1>;
> +				link = <&sw1p4>;
> +				phy-mode = "sgmii";
> +
> +				fixed-link {
> +					speed = <1000>;
> +					full-duplex;
> +				};
> +			};
> +
> +			port@2 {
> +				reg = <2>;
> +				ethernet = <&dpmac18>;
> +				phy-mode = "rgmii-id";
> +
> +				fixed-link {
> +					speed = <1000>;
> +					full-duplex;
> +				};
> +			};
> +
> +			port@3 {
> +				reg = <3>;
> +				label = "1ge_p2";
> +				phy-mode = "rgmii-id";
> +				phy-handle = <&sw2_mii3_phy>;
> +			};
> +
> +			port@4 {
> +				reg = <4>;
> +				label = "to_sw3";
> +				phy-mode = "2500base-x";
> +
> +				fixed-link {
> +					speed = <2500>;
> +					full-duplex;
> +				};
> +			};
> +
> +			port@5 {
> +				reg = <5>;
> +				label = "trx7";
> +				phy-mode = "internal";
> +				phy-handle = <&sw2_port5_base_t1_phy>;
> +			};
> +
> +			port@6 {
> +				reg = <6>;
> +				label = "trx8";
> +				phy-mode = "internal";
> +				phy-handle = <&sw2_port6_base_t1_phy>;
> +			};
> +
> +			port@7 {
> +				reg = <7>;
> +				label = "trx9";
> +				phy-mode = "internal";
> +				phy-handle = <&sw2_port7_base_t1_phy>;
> +			};
> +
> +			port@8 {
> +				reg = <8>;
> +				label = "trx10";
> +				phy-mode = "internal";
> +				phy-handle = <&sw2_port8_base_t1_phy>;
> +			};
> +
> +			port@9 {
> +				reg = <9>;
> +				label = "trx11";
> +				phy-mode = "internal";
> +				phy-handle = <&sw2_port9_base_t1_phy>;
> +			};
> +
> +			port@a {
> +				reg = <10>;
> +				label = "trx12";
> +				phy-mode = "internal";
> +				phy-handle = <&sw2_port10_base_t1_phy>;
> +			};
> +		};
> +
> +		mdios {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			mdio@0 {
> +				compatible = "nxp,sja1110-base-t1-mdio";
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				reg = <0>;
> +
> +				sw2_port5_base_t1_phy: ethernet-phy@1 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x1>;
> +				};
> +
> +				sw2_port6_base_t1_phy: ethernet-phy@2 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x2>;
> +				};
> +
> +				sw2_port7_base_t1_phy: ethernet-phy@3 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x3>;
> +				};
> +
> +				sw2_port8_base_t1_phy: ethernet-phy@4 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x4>;
> +				};
> +
> +				sw2_port9_base_t1_phy: ethernet-phy@5 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x5>;
> +				};
> +
> +				sw2_port10_base_t1_phy: ethernet-phy@6 {
> +					compatible = "ethernet-phy-ieee802.3-c45";
> +					reg = <0x6>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&uart0 {
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	status = "okay";
> +};
> +
> +&usb0 {
> +	status = "okay";
> +};
> +
> +&usb1 {
> +	status = "okay";
> +};
> -- 
> 2.25.1
>