Re: [PATCH v5 0/4] iio: chemical: Add support for Sensirion SCD4x CO2 sensor

[Jonathan Cameron <jic23@kernel.org>]

On Sun, 10 Oct 2021 16:59:19 +0100
Jonathan Cameron <jic23@kernel.org> wrote:

> On Fri,  8 Oct 2021 12:17:02 +0200
> Roan van Dijk <roan@protonic.nl> wrote:
> 
> > This series adds support for the Sensirion SCD4x sensor.
> > 
> > The driver supports continuous reads of temperature, relative humdity and CO2
> > concentration. There is an interval of 5 seconds between readings. During
> > this interval the drivers checks if the sensor has new data available.
> > 
> > The driver is based on the scd30 driver. However, The scd4x has become too
> > different to just expand the scd30 driver. I made a new driver instead of
> > expanding the scd30 driver. I hope I made the right choice by doing so?  
> 
> Applied to the togreg branch of iio.git with the issues Randy mentioned tidied
> up. Pushed out as testing for 0-day to see if it can find anything we missed

And indeed - I missed a bunch of places where explicit __be16 types should have
been used.

I've applied the following fixup, shout if it's wrong.


diff --git a/drivers/iio/chemical/scd4x.c b/drivers/iio/chemical/scd4x.c
index 09b34201c42b..ebebcb117ba2 100644
--- a/drivers/iio/chemical/scd4x.c
+++ b/drivers/iio/chemical/scd4x.c
@@ -263,7 +263,7 @@ static int scd4x_write_and_fetch(struct scd4x_state *state, enum scd4x_cmd cmd,
 static int scd4x_read_meas(struct scd4x_state *state, uint16_t *meas)
 {
 	int i, ret;
-	uint16_t buf[3];
+	__be16 buf[3];
 
 	ret = scd4x_read(state, CMD_READ_MEAS, buf, sizeof(buf));
 	if (ret)
@@ -282,12 +282,13 @@ static int scd4x_wait_meas_poll(struct scd4x_state *state)
 	int ret;
 
 	do {
+		__be16 bval;
 		uint16_t val;
 
-		ret = scd4x_read(state, CMD_GET_DATA_READY, &val, sizeof(val));
+		ret = scd4x_read(state, CMD_GET_DATA_READY, &bval, sizeof(bval));
 		if (ret)
 			return -EIO;
-		val = be16_to_cpu(val);
+		val = be16_to_cpu(bval);
 
 		/* new measurement available */
 		if (val & 0x7FF)
@@ -333,7 +334,7 @@ static int scd4x_read_raw(struct iio_dev *indio_dev,
 {
 	struct scd4x_state *state = iio_priv(indio_dev);
 	int ret;
-	uint16_t tmp;
+	__be16 tmp;
 
 	switch (mask) {
 	case IIO_CHAN_INFO_RAW:
@@ -405,17 +406,18 @@ static ssize_t calibration_auto_enable_show(struct device *dev,
 	struct iio_dev *indio_dev = dev_to_iio_dev(dev);
 	struct scd4x_state *state = iio_priv(indio_dev);
 	int ret;
-	uint16_t val;
+	__be16 bval;
+	u16 val;
 
 	mutex_lock(&state->lock);
-	ret = scd4x_read(state, CMD_GET_ASC, &val, sizeof(val));
+	ret = scd4x_read(state, CMD_GET_ASC, &bval, sizeof(bval));
 	mutex_unlock(&state->lock);
 	if (ret) {
 		dev_err(dev, "failed to read automatic calibration");
 		return ret;
 	}
 
-	val = (be16_to_cpu(val) & SCD4X_READY_MASK) ? 1 : 0;
+	val = (be16_to_cpu(bval) & SCD4X_READY_MASK) ? 1 : 0;
 
 	return sprintf(buf, "%d\n", val);
 }


> 
> Thanks,
> 
> Jonathan
> 
> > 
> > Changes since v5:
> > scd4x.c:
> >   - Fix bug in trigger_handler
> > 
> > Changes since v4:
> > scd4x.c:
> >   - Minor fixes in documentation
> >   - Reorder trigger_handler so memcpy is not needed anymore
> > Documentation:
> >   - Change information about the KernelVersion for the 
> >     calibration_forced_value_available
> > 
> > Changes since v3:
> > scd4x.c
> >   - Change read and write_and_fetch function parameter. CRC byte is now
> >     hidden inside the function.
> >   - Fix minor style issues
> >   - Add calibration_forced_value_available attribute to the driver
> >   - Remove including BUFFER_TRIGGERED
> >   - Change calibbias to raw ADC readings rather than converting it to
> >     milli degrees C.
> > Documentation:
> >   - Change description of driver attributes
> >   - Add calibration_forced_value_available documentation
> > 
> > Changes since v2:
> > scd4x.c:
> >   - Change boolean operations
> >   - Document scope of lock
> >   - Remove device *dev from struct
> >   - Add goto block for errror handling
> >   - Add function to read value per channel in read_raw
> >   - Fix bug with lock in error paths
> >   - Remove conversion of humidity and temperature values
> >   - Add scale and offset to temperature channel
> >   - Add scale to humidity channel
> >   - Move memset out of locked section
> >   - Remove unused irq functions
> >   - Move device register at end of probe function
> > Documentation:
> >   - Copy content of sysfs-bus-iio-scd30 to sysfs-bus-iio
> >   - Remove Documentation/ABI/testing/sysfs-bus-iio-scd30
> > 
> > Changes since v1:
> > dt-bindings:
> >   - Separated compatible string for each sensor type
> > scd4x.c:
> >   - Changed probe, resume and suspend functions to static
> >   - Added SIMPLE_DEV_PM_OPS function call for power management
> >     operations.
> > 
> > Roan van Dijk (4):
> >   dt-bindings: iio: chemical: sensirion,scd4x: Add yaml description
> >   MAINTAINERS: Add myself as maintainer of the scd4x driver
> >   drivers: iio: chemical: Add support for Sensirion SCD4x CO2 sensor
> >   iio: documentation: Document scd4x calibration use
> > 
> >  Documentation/ABI/testing/sysfs-bus-iio       |  41 ++
> >  Documentation/ABI/testing/sysfs-bus-iio-scd30 |  34 -
> >  .../iio/chemical/sensirion,scd4x.yaml         |  46 ++
> >  MAINTAINERS                                   |   6 +
> >  drivers/iio/chemical/Kconfig                  |  13 +
> >  drivers/iio/chemical/Makefile                 |   1 +
> >  drivers/iio/chemical/scd4x.c                  | 689 ++++++++++++++++++
> >  7 files changed, 796 insertions(+), 34 deletions(-)
> >  delete mode 100644 Documentation/ABI/testing/sysfs-bus-iio-scd30
> >  create mode 100644 Documentation/devicetree/bindings/iio/chemical/sensirion,scd4x.yaml
> >  create mode 100644 drivers/iio/chemical/scd4x.c
> >   
>