From: Vamsi Krishna Lanka <quic_vamslank@quicinc.com>
To: Vinod Koul <vkoul@kernel.org>, <g@quicinc.com>
Cc: <agross@kernel.org>, <bjorn.andersson@linaro.org>,
<mturquette@baylibre.com>, <sboyd@kernel.org>,
<robh+dt@kernel.org>, <tglx@linutronix.de>, <maz@kernel.org>,
<linux-arm-msm@vger.kernel.org>, <linux-clk@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
<manivannan.sadhasivam@linaro.org>
Subject: Re: [PATCH v4 2/6] clk: qcom: Add LUCID_EVO PLL type for SDX65
Date: Wed, 17 Nov 2021 17:54:50 -0800 [thread overview]
Message-ID: <20211118015450.GB18984@quicinc.com> (raw)
In-Reply-To: <YZNq+Y07kwhbIboe@matsya>
On Tue, Nov 16, 2021 at 01:55:29PM +0530, Vinod Koul wrote:
> On 15-11-21, 23:38, quic_vamslank@quicinc.com wrote:
> > From: Vamsi Krishna Lanka <quic_vamslank@quicinc.com>
> >
> > Add a LUCID_EVO PLL type for SDX65 SoC from Qualcomm.
> >
> > Signed-off-by: Vamsi Krishna Lanka <quic_vamslank@quicinc.com>
> > ---
> > drivers/clk/qcom/clk-alpha-pll.c | 171 +++++++++++++++++++++++++++++++
> > drivers/clk/qcom/clk-alpha-pll.h | 3 +
> > 2 files changed, 174 insertions(+)
> >
> > diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
> > index eaedcceb766f..b2dbb8d56773 100644
> > --- a/drivers/clk/qcom/clk-alpha-pll.c
> > +++ b/drivers/clk/qcom/clk-alpha-pll.c
> > @@ -1,5 +1,6 @@
> > // SPDX-License-Identifier: GPL-2.0
> > /*
> > + * Copyright (c) 2021, Qualcomm Innovation Center, Inc. All rights reserved.
>
> This line should ideally come after the below line..
Will do.
>
> > * Copyright (c) 2015, 2018, The Linux Foundation. All rights reserved.
> > */
> >
> > @@ -139,6 +140,20 @@ const u8 clk_alpha_pll_regs[][PLL_OFF_MAX_REGS] = {
> > [PLL_OFF_OPMODE] = 0x28,
> > [PLL_OFF_STATUS] = 0x38,
> > },
> > + [CLK_ALPHA_PLL_TYPE_LUCID_EVO] = {
> > + [PLL_OFF_OPMODE] = 0x04,
> > + [PLL_OFF_STATUS] = 0x0c,
> > + [PLL_OFF_L_VAL] = 0x10,
> > + [PLL_OFF_ALPHA_VAL] = 0x14,
> > + [PLL_OFF_USER_CTL] = 0x18,
> > + [PLL_OFF_USER_CTL_U] = 0x1c,
> > + [PLL_OFF_CONFIG_CTL] = 0x20,
> > + [PLL_OFF_CONFIG_CTL_U] = 0x24,
> > + [PLL_OFF_CONFIG_CTL_U1] = 0x28,
> > + [PLL_OFF_TEST_CTL] = 0x2c,
> > + [PLL_OFF_TEST_CTL_U] = 0x30,
> > + [PLL_OFF_TEST_CTL_U1] = 0x34,
> > + },
> > };
> > EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
> >
> > @@ -175,6 +190,10 @@ EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
> > #define LUCID_5LPE_PLL_LATCH_INPUT BIT(14)
> > #define LUCID_5LPE_ENABLE_VOTE_RUN BIT(21)
> >
> > +/* LUCID EVO PLL specific settings and offsets */
> > +#define LUCID_EVO_ENABLE_VOTE_RUN BIT(25)
> > +#define LUCID_EVO_PLL_L_VAL_MASK GENMASK(15, 0)
> > +
> > /* ZONDA PLL specific */
> > #define ZONDA_PLL_OUT_MASK 0xf
> > #define ZONDA_STAY_IN_CFA BIT(16)
> > @@ -1951,3 +1970,155 @@ const struct clk_ops clk_alpha_pll_zonda_ops = {
> > .set_rate = clk_zonda_pll_set_rate,
> > };
> > EXPORT_SYMBOL(clk_alpha_pll_zonda_ops);
> > +
> > +static int alpha_pll_lucid_evo_enable(struct clk_hw *hw)
> > +{
> > + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
> > + struct regmap *regmap = pll->clkr.regmap;
> > + u32 val;
> > + int ret;
> > +
> > + ret = regmap_read(regmap, PLL_USER_CTL(pll), &val);
> > + if (ret)
> > + return ret;
> > +
> > + /* If in FSM mode, just vote for it */
> > + if (val & LUCID_EVO_ENABLE_VOTE_RUN) {
> > + ret = clk_enable_regmap(hw);
> > + if (ret)
> > + return ret;
> > + return wait_for_pll_enable_lock(pll);
> > + }
> > +
> > + /* Check if PLL is already enabled */
> > + ret = trion_pll_is_enabled(pll, regmap);
> > + if (ret < 0)
> > + return ret;
> > + else if (ret) {
> > + pr_warn("%s PLL is already enabled\n",
> > + clk_hw_get_name(&pll->clkr.hw));
>
> this should fit in a single line
Will do.
>
> > + return 0;
> > + }
> > +
> > + ret = regmap_update_bits(regmap, PLL_MODE(pll), PLL_RESET_N, PLL_RESET_N);
> > + if (ret)
> > + return ret;
> > +
> > + /* Set operation mode to RUN */
> > + regmap_write(regmap, PLL_OPMODE(pll), PLL_RUN);
> > +
> > + ret = wait_for_pll_enable_lock(pll);
> > + if (ret)
> > + return ret;
> > +
> > + /* Enable the PLL outputs */
> > + ret = regmap_update_bits(regmap, PLL_USER_CTL(pll), PLL_OUT_MASK, PLL_OUT_MASK);
> > + if (ret)
> > + return ret;
> > +
> > + /* Enable the global PLL outputs */
> > + ret = regmap_update_bits(regmap, PLL_MODE(pll), PLL_OUTCTRL, PLL_OUTCTRL);
> > + if (ret)
> > + return ret;
> > +
> > + /* Ensure that the write above goes through before returning. */
> > + mb();
> > + return ret;
> > +}
> > +
> > +static void alpha_pll_lucid_evo_disable(struct clk_hw *hw)
> > +{
> > + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
> > + struct regmap *regmap = pll->clkr.regmap;
> > + u32 val;
> > + int ret;
> > +
> > + ret = regmap_read(regmap, PLL_USER_CTL(pll), &val);
> > + if (ret)
> > + return;
> > +
> > + /* If in FSM mode, just unvote it */
> > + if (val & LUCID_EVO_ENABLE_VOTE_RUN) {
> > + clk_disable_regmap(hw);
> > + return;
> > + }
> > +
> > + /* Disable the global PLL output */
> > + ret = regmap_update_bits(regmap, PLL_MODE(pll), PLL_OUTCTRL, 0);
> > + if (ret)
> > + return;
> > +
> > + /* Disable the PLL outputs */
> > + ret = regmap_update_bits(regmap, PLL_USER_CTL(pll), PLL_OUT_MASK, 0);
> > + if (ret)
> > + return;
> > +
> > + /* Place the PLL mode in STANDBY */
> > + regmap_write(regmap, PLL_OPMODE(pll), PLL_STANDBY);
> > +}
> > +
> > +static unsigned long alpha_pll_lucid_evo_recalc_rate(struct clk_hw *hw,
> > + unsigned long parent_rate)
>
> pls align this to preceding line open brace
Will do.
>
> > +{
> > + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
> > + struct regmap *regmap = pll->clkr.regmap;
> > + u32 l, frac;
> > +
> > + regmap_read(regmap, PLL_L_VAL(pll), &l);
> > + l &= LUCID_EVO_PLL_L_VAL_MASK;
> > + regmap_read(regmap, PLL_ALPHA_VAL(pll), &frac);
> > +
> > + return alpha_pll_calc_rate(parent_rate, l, frac, pll_alpha_width(pll));
> > +}
>
> I think this can use __alpha_pll_trion_set_rate()
I didn't get with which function are you comparing this. I cannot able to
find any function similar to this.
>
> > +
> > +static int clk_lucid_evo_pll_postdiv_set_rate(struct clk_hw *hw,
> > + unsigned long rate, unsigned long parent_rate)
> > +{
> > + struct clk_alpha_pll_postdiv *pll = to_clk_alpha_pll_postdiv(hw);
> > + struct regmap *regmap = pll->clkr.regmap;
> > + int i, val, div, ret;
> > +
> > + /*
> > + * If the PLL is in FSM mode, then treat set_rate callback as a
> > + * no-operation.
> > + */
> > + ret = regmap_read(regmap, PLL_USER_CTL(pll), &val);
> > + if (ret)
> > + return ret;
> > +
> > + if (val & LUCID_EVO_ENABLE_VOTE_RUN)
> > + return 0;
> > +
> > + if (!pll->post_div_table) {
> > + pr_err("Missing the post_div_table for the PLL\n");
> > + return -EINVAL;
> > + }
> > +
> > + div = DIV_ROUND_UP_ULL((u64)parent_rate, rate);
> > + for (i = 0; i < pll->num_post_div; i++) {
> > + if (pll->post_div_table[i].div == div) {
> > + val = pll->post_div_table[i].val;
> > + break;
> > + }
> > + }
> > +
> > + return regmap_update_bits(regmap, PLL_USER_CTL(pll),
> > + (BIT(pll->width) - 1) << pll->post_div_shift,
> > + val << pll->post_div_shift);
> > +}
>
> This looks _very_ similar to clk_lucid_5lpe_pll_postdiv_set_rate() maybe
> add a helper which both can use and pass on the
> LUCID_EVO_ENABLE_VOTE_RUN as argument to helper?
That's a good thought. I can do that.
>
> --
> ~Vinod
next prev parent reply other threads:[~2021-11-18 1:54 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-11-16 7:38 [PATCH v4 0/6] Add Pdc, GCC and RPMh clock support for SDX65 quic_vamslank
2021-11-16 7:38 ` [PATCH v4 1/6] dt-bindings: clock: Add SDX65 GCC clock bindings quic_vamslank
2021-11-19 1:06 ` Rob Herring
2021-11-16 7:38 ` [PATCH v4 2/6] clk: qcom: Add LUCID_EVO PLL type for SDX65 quic_vamslank
2021-11-16 8:25 ` Vinod Koul
2021-11-18 1:54 ` Vamsi Krishna Lanka [this message]
2021-11-18 4:41 ` Vinod Koul
2021-11-16 7:38 ` [PATCH v4 3/6] clk: qcom: Add SDX65 GCC support quic_vamslank
2021-11-16 8:33 ` Vinod Koul
2021-11-18 1:51 ` Vamsi Krishna Lanka
2021-11-18 4:39 ` Vinod Koul
2021-11-18 5:04 ` Vamsi Krishna Lanka
2021-11-18 5:08 ` Vinod Koul
2021-11-16 7:38 ` [PATCH v4 4/6] dt-bindings: clock: Introduce RPMHCC bindings for SDX65 quic_vamslank
2021-11-16 8:34 ` Vinod Koul
2021-11-16 7:38 ` [PATCH v4 5/6] clk: qcom: Add support for SDX65 RPMh clocks quic_vamslank
2021-11-16 8:35 ` Vinod Koul
2021-11-16 7:38 ` [PATCH v4 6/6] dt-bindings: clock: Introduce pdc bindings for SDX65 quic_vamslank
2021-11-16 8:36 ` Vinod Koul
2021-11-16 8:33 ` [PATCH v4 0/6] Add Pdc, GCC and RPMh clock support " Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211118015450.GB18984@quicinc.com \
--to=quic_vamslank@quicinc.com \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=g@quicinc.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=manivannan.sadhasivam@linaro.org \
--cc=maz@kernel.org \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=tglx@linutronix.de \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).