* [PATCH v5] i2c: qcom-geni: Add support for GPI DMA
@ 2022-01-31 12:04 Vinod Koul
2022-02-17 17:35 ` Bjorn Andersson
2022-02-17 17:51 ` Dmitry Baryshkov
0 siblings, 2 replies; 5+ messages in thread
From: Vinod Koul @ 2022-01-31 12:04 UTC (permalink / raw)
To: Bjorn Andersson, Wolfram Sang
Cc: linux-arm-msm, Vinod Koul, Andy Gross, Douglas Anderson,
Matthias Kaehlcke, linux-i2c, linux-kernel, Alexey Minnekhanov
QUP Serial engines supports data transfers thru FIFO mode, SE DMA mode and
lastly GPI DMA mode. Former two are already supported and this adds supports the
last mode.
In GPI DMA mode, the firmware is issued commands by driver to perform DMA
and setup the serial port.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
Changes since v4:
- Fix buildbot warn
- Fix flase warn reported by Alexey
- Fix feedback from Bjorn and cleanup the probe code and add more details
in changelog
Changes since v3:
- remove separate tx and rx function for gsi dma and make a common one
- remove global structs and use local variables instead
drivers/i2c/busses/i2c-qcom-geni.c | 300 ++++++++++++++++++++++++++---
1 file changed, 273 insertions(+), 27 deletions(-)
diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
index 6d635a7c104c..696253d178a6 100644
--- a/drivers/i2c/busses/i2c-qcom-geni.c
+++ b/drivers/i2c/busses/i2c-qcom-geni.c
@@ -3,7 +3,9 @@
#include <linux/acpi.h>
#include <linux/clk.h>
+#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
+#include <linux/dma/qcom-gpi-dma.h>
#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
@@ -48,6 +50,9 @@
#define LOW_COUNTER_SHFT 10
#define CYCLE_COUNTER_MSK GENMASK(9, 0)
+#define I2C_PACK_TX BIT(0)
+#define I2C_PACK_RX BIT(1)
+
enum geni_i2c_err_code {
GP_IRQ0,
NACK,
@@ -89,6 +94,9 @@ struct geni_i2c_dev {
void *dma_buf;
size_t xfer_len;
dma_addr_t dma_addr;
+ struct dma_chan *tx_c;
+ struct dma_chan *rx_c;
+ bool gpi_mode;
};
struct geni_i2c_err_log {
@@ -456,12 +464,199 @@ static int geni_i2c_tx_one_msg(struct geni_i2c_dev *gi2c, struct i2c_msg *msg,
return gi2c->err;
}
+static void i2c_gpi_cb_result(void *cb, const struct dmaengine_result *result)
+{
+ struct geni_i2c_dev *gi2c = cb;
+
+ if (result->result != DMA_TRANS_NOERROR) {
+ dev_err(gi2c->se.dev, "DMA txn failed:%d\n", result->result);
+ return;
+ }
+
+ if (result->residue)
+ dev_dbg(gi2c->se.dev, "DMA xfer has pending: %d\n", result->residue);
+
+ complete(&gi2c->done);
+}
+
+static void geni_i2c_gpi_unmap(struct geni_i2c_dev *gi2c, struct i2c_msg *msg,
+ void *tx_buf, dma_addr_t tx_addr,
+ void *rx_buf, dma_addr_t rx_addr)
+{
+ if (tx_buf) {
+ dma_unmap_single(gi2c->se.dev->parent, tx_addr, msg->len, DMA_TO_DEVICE);
+ i2c_put_dma_safe_msg_buf(tx_buf, msg, false);
+ }
+
+ if (rx_buf) {
+ dma_unmap_single(gi2c->se.dev->parent, rx_addr, msg->len, DMA_FROM_DEVICE);
+ i2c_put_dma_safe_msg_buf(rx_buf, msg, false);
+ }
+}
+
+static int geni_i2c_gpi(struct geni_i2c_dev *gi2c, struct i2c_msg *msg,
+ struct dma_slave_config *config, dma_addr_t *dma_addr_p,
+ void **buf, unsigned int op, struct dma_chan *dma_chan)
+{
+ struct gpi_i2c_config *peripheral;
+ unsigned int flags;
+ void *dma_buf;
+ dma_addr_t addr;
+ enum dma_data_direction map_dirn;
+ enum dma_transfer_direction dma_dirn;
+ struct dma_async_tx_descriptor *desc;
+ int ret;
+
+ peripheral = config->peripheral_config;
+
+ dma_buf = i2c_get_dma_safe_msg_buf(msg, 1);
+ if (!dma_buf)
+ return -ENOMEM;
+
+ if (op == I2C_WRITE)
+ map_dirn = DMA_TO_DEVICE;
+ else
+ map_dirn = DMA_FROM_DEVICE;
+
+ addr = dma_map_single(gi2c->se.dev->parent, dma_buf, msg->len, map_dirn);
+ if (dma_mapping_error(gi2c->se.dev->parent, addr)) {
+ i2c_put_dma_safe_msg_buf(dma_buf, msg, false);
+ return -ENOMEM;
+ }
+
+ /* set the length as message for rx txn */
+ peripheral->rx_len = msg->len;
+ peripheral->op = op;
+
+ ret = dmaengine_slave_config(dma_chan, config);
+ if (ret) {
+ dev_err(gi2c->se.dev, "dma config error: %d for op:%d\n", ret, op);
+ goto err_config;
+ }
+
+ peripheral->set_config = 0;
+ peripheral->multi_msg = true;
+ flags = DMA_PREP_INTERRUPT | DMA_CTRL_ACK;
+
+ if (op == I2C_WRITE)
+ dma_dirn = DMA_MEM_TO_DEV;
+ else
+ dma_dirn = DMA_DEV_TO_MEM;
+
+ desc = dmaengine_prep_slave_single(dma_chan, addr, msg->len, dma_dirn, flags);
+ if (!desc) {
+ dev_err(gi2c->se.dev, "prep_slave_sg failed\n");
+ ret = -EIO;
+ goto err_config;
+ }
+
+ desc->callback_result = i2c_gpi_cb_result;
+ desc->callback_param = gi2c;
+
+ dmaengine_submit(desc);
+ *dma_addr_p = addr;
+
+ return 0;
+
+err_config:
+ dma_unmap_single(gi2c->se.dev->parent, addr, msg->len, map_dirn);
+ i2c_put_dma_safe_msg_buf(dma_buf, msg, false);
+ return ret;
+}
+
+static int geni_i2c_gpi_xfer(struct geni_i2c_dev *gi2c, struct i2c_msg msgs[], int num)
+{
+ struct dma_slave_config config = {};
+ struct gpi_i2c_config peripheral = {};
+ int i, ret = 0, timeout;
+ dma_addr_t tx_addr, rx_addr;
+ void *tx_buf = NULL, *rx_buf = NULL;
+ const struct geni_i2c_clk_fld *itr = gi2c->clk_fld;
+
+ config.peripheral_config = &peripheral;
+ config.peripheral_size = sizeof(peripheral);
+
+ peripheral.pack_enable = I2C_PACK_TX | I2C_PACK_RX;
+ peripheral.cycle_count = itr->t_cycle_cnt;
+ peripheral.high_count = itr->t_high_cnt;
+ peripheral.low_count = itr->t_low_cnt;
+ peripheral.clk_div = itr->clk_div;
+ peripheral.set_config = 1;
+ peripheral.multi_msg = false;
+
+ for (i = 0; i < num; i++) {
+ gi2c->cur = &msgs[i];
+ dev_dbg(gi2c->se.dev, "msg[%d].len:%d\n", i, gi2c->cur->len);
+
+ peripheral.stretch = 0;
+ if (i < num - 1)
+ peripheral.stretch = 1;
+
+ peripheral.addr = msgs[i].addr;
+
+ if (msgs[i].flags & I2C_M_RD) {
+ ret = geni_i2c_gpi(gi2c, &msgs[i], &config, &rx_addr, &rx_buf, I2C_READ, gi2c->rx_c);
+ if (ret)
+ goto err;
+ }
+
+ ret = geni_i2c_gpi(gi2c, &msgs[i], &config, &tx_addr, &tx_buf, I2C_WRITE, gi2c->tx_c);
+ if (ret)
+ goto err;
+
+ if (msgs[i].flags & I2C_M_RD)
+ dma_async_issue_pending(gi2c->rx_c);
+ dma_async_issue_pending(gi2c->tx_c);
+
+ timeout = wait_for_completion_timeout(&gi2c->done, XFER_TIMEOUT);
+ if (!timeout) {
+ dev_err(gi2c->se.dev, "I2C timeout gpi flags:%d addr:0x%x\n",
+ gi2c->cur->flags, gi2c->cur->addr);
+ ret = gi2c->err = -ETIMEDOUT;
+ goto err;
+ }
+
+ geni_i2c_gpi_unmap(gi2c, &msgs[i], tx_buf, tx_addr, rx_buf, rx_addr);
+ }
+
+ return 0;
+
+err:
+ dmaengine_terminate_sync(gi2c->rx_c);
+ dmaengine_terminate_sync(gi2c->tx_c);
+ geni_i2c_gpi_unmap(gi2c, &msgs[i], tx_buf, tx_addr, rx_buf, rx_addr);
+ return ret;
+}
+
+static int geni_i2c_fifo_xfer(struct geni_i2c_dev *gi2c,
+ struct i2c_msg msgs[], int num)
+{
+ int i, ret = 0;
+
+ for (i = 0; i < num; i++) {
+ u32 m_param = i < (num - 1) ? STOP_STRETCH : 0;
+
+ m_param |= ((msgs[i].addr << SLV_ADDR_SHFT) & SLV_ADDR_MSK);
+
+ gi2c->cur = &msgs[i];
+ if (msgs[i].flags & I2C_M_RD)
+ ret = geni_i2c_rx_one_msg(gi2c, &msgs[i], m_param);
+ else
+ ret = geni_i2c_tx_one_msg(gi2c, &msgs[i], m_param);
+
+ if (ret)
+ break;
+ }
+
+ return ret;
+}
+
static int geni_i2c_xfer(struct i2c_adapter *adap,
struct i2c_msg msgs[],
int num)
{
struct geni_i2c_dev *gi2c = i2c_get_adapdata(adap);
- int i, ret;
+ int ret;
gi2c->err = 0;
reinit_completion(&gi2c->done);
@@ -475,22 +670,11 @@ static int geni_i2c_xfer(struct i2c_adapter *adap,
}
qcom_geni_i2c_conf(gi2c);
- for (i = 0; i < num; i++) {
- u32 m_param = i < (num - 1) ? STOP_STRETCH : 0;
-
- m_param |= ((msgs[i].addr << SLV_ADDR_SHFT) & SLV_ADDR_MSK);
-
- gi2c->cur = &msgs[i];
- if (msgs[i].flags & I2C_M_RD)
- ret = geni_i2c_rx_one_msg(gi2c, &msgs[i], m_param);
- else
- ret = geni_i2c_tx_one_msg(gi2c, &msgs[i], m_param);
- if (ret)
- break;
- }
- if (ret == 0)
- ret = num;
+ if (gi2c->gpi_mode)
+ ret = geni_i2c_gpi_xfer(gi2c, msgs, num);
+ else
+ ret = geni_i2c_fifo_xfer(gi2c, msgs, num);
pm_runtime_mark_last_busy(gi2c->se.dev);
pm_runtime_put_autosuspend(gi2c->se.dev);
@@ -517,11 +701,52 @@ static const struct acpi_device_id geni_i2c_acpi_match[] = {
MODULE_DEVICE_TABLE(acpi, geni_i2c_acpi_match);
#endif
+static void release_gpi_dma(struct geni_i2c_dev *gi2c)
+{
+ if (gi2c->rx_c)
+ dma_release_channel(gi2c->rx_c);
+
+ if (gi2c->tx_c)
+ dma_release_channel(gi2c->tx_c);
+}
+
+static int setup_gpi_dma(struct geni_i2c_dev *gi2c)
+{
+ int ret;
+
+ geni_se_select_mode(&gi2c->se, GENI_GPI_DMA);
+ gi2c->tx_c = dma_request_chan(gi2c->se.dev, "tx");
+ if (IS_ERR(gi2c->tx_c)) {
+ ret = dev_err_probe(gi2c->se.dev, PTR_ERR(gi2c->tx_c),
+ "Failed to get tx DMA ch\n");
+ if (ret < 0)
+ goto err_tx;
+ }
+
+ gi2c->rx_c = dma_request_chan(gi2c->se.dev, "rx");
+ if (IS_ERR(gi2c->rx_c)) {
+ ret = dev_err_probe(gi2c->se.dev, PTR_ERR(gi2c->rx_c),
+ "Failed to get rx DMA ch\n");
+ if (ret < 0)
+ goto err_rx;
+ }
+
+ dev_dbg(gi2c->se.dev, "Grabbed GPI dma channels\n");
+ return 0;
+
+err_rx:
+ dma_release_channel(gi2c->tx_c);
+ gi2c->tx_c = NULL;
+err_tx:
+ gi2c->rx_c = NULL;
+ return ret;
+}
+
static int geni_i2c_probe(struct platform_device *pdev)
{
struct geni_i2c_dev *gi2c;
struct resource *res;
- u32 proto, tx_depth;
+ u32 proto, tx_depth, fifo_disable;
int ret;
struct device *dev = &pdev->dev;
@@ -601,27 +826,43 @@ static int geni_i2c_probe(struct platform_device *pdev)
return ret;
}
proto = geni_se_read_proto(&gi2c->se);
- tx_depth = geni_se_get_tx_fifo_depth(&gi2c->se);
if (proto != GENI_SE_I2C) {
dev_err(dev, "Invalid proto %d\n", proto);
geni_se_resources_off(&gi2c->se);
return -ENXIO;
}
- gi2c->tx_wm = tx_depth - 1;
- geni_se_init(&gi2c->se, gi2c->tx_wm, tx_depth);
- geni_se_config_packing(&gi2c->se, BITS_PER_BYTE, PACKING_BYTES_PW,
- true, true, true);
+
+ fifo_disable = readl_relaxed(gi2c->se.base + GENI_IF_DISABLE_RO) & FIFO_IF_DISABLE;
+ if (fifo_disable) {
+ /* FIFO is disabled, so we can only use GPI DMA */
+ gi2c->gpi_mode = true;
+ ret = setup_gpi_dma(gi2c);
+ if (ret) {
+ dev_err(dev, "Failed to setup GPI DMA mode:%d ret\n", ret);
+ return ret;
+ }
+
+ dev_dbg(dev, "Using GPI DMA mode for I2C\n");
+ } else {
+ gi2c->gpi_mode = false;
+ tx_depth = geni_se_get_tx_fifo_depth(&gi2c->se);
+ gi2c->tx_wm = tx_depth - 1;
+ geni_se_init(&gi2c->se, gi2c->tx_wm, tx_depth);
+ geni_se_config_packing(&gi2c->se, BITS_PER_BYTE,
+ PACKING_BYTES_PW, true, true, true);
+
+ dev_dbg(dev, "i2c fifo/se-dma mode. fifo depth:%d\n", tx_depth);
+ }
+
ret = geni_se_resources_off(&gi2c->se);
if (ret) {
dev_err(dev, "Error turning off resources %d\n", ret);
- return ret;
+ goto err_dma;
}
ret = geni_icc_disable(&gi2c->se);
if (ret)
- return ret;
-
- dev_dbg(dev, "i2c fifo/se-dma mode. fifo depth:%d\n", tx_depth);
+ goto err_dma;
gi2c->suspended = 1;
pm_runtime_set_suspended(gi2c->se.dev);
@@ -633,18 +874,23 @@ static int geni_i2c_probe(struct platform_device *pdev)
if (ret) {
dev_err(dev, "Error adding i2c adapter %d\n", ret);
pm_runtime_disable(gi2c->se.dev);
- return ret;
+ goto err_dma;
}
dev_dbg(dev, "Geni-I2C adaptor successfully added\n");
return 0;
+
+err_dma:
+ release_gpi_dma(gi2c);
+ return ret;
}
static int geni_i2c_remove(struct platform_device *pdev)
{
struct geni_i2c_dev *gi2c = platform_get_drvdata(pdev);
+ release_gpi_dma(gi2c);
i2c_del_adapter(&gi2c->adap);
pm_runtime_disable(gi2c->se.dev);
return 0;
--
2.31.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v5] i2c: qcom-geni: Add support for GPI DMA
2022-01-31 12:04 [PATCH v5] i2c: qcom-geni: Add support for GPI DMA Vinod Koul
@ 2022-02-17 17:35 ` Bjorn Andersson
2022-02-18 6:33 ` Vinod Koul
2022-02-17 17:51 ` Dmitry Baryshkov
1 sibling, 1 reply; 5+ messages in thread
From: Bjorn Andersson @ 2022-02-17 17:35 UTC (permalink / raw)
To: Vinod Koul
Cc: Wolfram Sang, linux-arm-msm, Andy Gross, Douglas Anderson,
Matthias Kaehlcke, linux-i2c, linux-kernel, Alexey Minnekhanov
On Mon 31 Jan 04:04 PST 2022, Vinod Koul wrote:
> QUP Serial engines supports data transfers thru FIFO mode, SE DMA mode and
> lastly GPI DMA mode. Former two are already supported and this adds supports the
> last mode.
>
> In GPI DMA mode, the firmware is issued commands by driver to perform DMA
> and setup the serial port.
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
>
> Changes since v4:
> - Fix buildbot warn
> - Fix flase warn reported by Alexey
> - Fix feedback from Bjorn and cleanup the probe code and add more details
> in changelog
>
> Changes since v3:
> - remove separate tx and rx function for gsi dma and make a common one
> - remove global structs and use local variables instead
>
> drivers/i2c/busses/i2c-qcom-geni.c | 300 ++++++++++++++++++++++++++---
> 1 file changed, 273 insertions(+), 27 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
> index 6d635a7c104c..696253d178a6 100644
> --- a/drivers/i2c/busses/i2c-qcom-geni.c
> +++ b/drivers/i2c/busses/i2c-qcom-geni.c
> @@ -3,7 +3,9 @@
>
> #include <linux/acpi.h>
> #include <linux/clk.h>
> +#include <linux/dmaengine.h>
> #include <linux/dma-mapping.h>
> +#include <linux/dma/qcom-gpi-dma.h>
> #include <linux/err.h>
> #include <linux/i2c.h>
> #include <linux/interrupt.h>
> @@ -48,6 +50,9 @@
> #define LOW_COUNTER_SHFT 10
> #define CYCLE_COUNTER_MSK GENMASK(9, 0)
>
> +#define I2C_PACK_TX BIT(0)
> +#define I2C_PACK_RX BIT(1)
> +
> enum geni_i2c_err_code {
> GP_IRQ0,
> NACK,
> @@ -89,6 +94,9 @@ struct geni_i2c_dev {
> void *dma_buf;
> size_t xfer_len;
> dma_addr_t dma_addr;
> + struct dma_chan *tx_c;
> + struct dma_chan *rx_c;
> + bool gpi_mode;
> };
>
> struct geni_i2c_err_log {
> @@ -456,12 +464,199 @@ static int geni_i2c_tx_one_msg(struct geni_i2c_dev *gi2c, struct i2c_msg *msg,
> return gi2c->err;
> }
>
> +static void i2c_gpi_cb_result(void *cb, const struct dmaengine_result *result)
> +{
> + struct geni_i2c_dev *gi2c = cb;
> +
> + if (result->result != DMA_TRANS_NOERROR) {
> + dev_err(gi2c->se.dev, "DMA txn failed:%d\n", result->result);
Iiuc the API the expectation is that if we get !NOERROR we shouldn't
expect to get NOERROR after that.
If so we're just returning here and leaving geni_i2c_gpi_xfer() to just
timeout in a HZ or so. Given that xfer happens under the adaptor lock,
how about carrying an error in geni_i2c_dev and complete(&done) here as
well?
> + return;
> + }
> +
> + if (result->residue)
> + dev_dbg(gi2c->se.dev, "DMA xfer has pending: %d\n", result->residue);
> +
> + complete(&gi2c->done);
> +}
> +
[..]
> +
> +static int geni_i2c_gpi_xfer(struct geni_i2c_dev *gi2c, struct i2c_msg msgs[], int num)
> +{
> + struct dma_slave_config config = {};
> + struct gpi_i2c_config peripheral = {};
> + int i, ret = 0, timeout;
> + dma_addr_t tx_addr, rx_addr;
> + void *tx_buf = NULL, *rx_buf = NULL;
> + const struct geni_i2c_clk_fld *itr = gi2c->clk_fld;
> +
> + config.peripheral_config = &peripheral;
> + config.peripheral_size = sizeof(peripheral);
> +
> + peripheral.pack_enable = I2C_PACK_TX | I2C_PACK_RX;
> + peripheral.cycle_count = itr->t_cycle_cnt;
> + peripheral.high_count = itr->t_high_cnt;
> + peripheral.low_count = itr->t_low_cnt;
> + peripheral.clk_div = itr->clk_div;
> + peripheral.set_config = 1;
> + peripheral.multi_msg = false;
> +
> + for (i = 0; i < num; i++) {
> + gi2c->cur = &msgs[i];
> + dev_dbg(gi2c->se.dev, "msg[%d].len:%d\n", i, gi2c->cur->len);
> +
> + peripheral.stretch = 0;
> + if (i < num - 1)
> + peripheral.stretch = 1;
> +
> + peripheral.addr = msgs[i].addr;
> +
> + if (msgs[i].flags & I2C_M_RD) {
> + ret = geni_i2c_gpi(gi2c, &msgs[i], &config, &rx_addr, &rx_buf, I2C_READ, gi2c->rx_c);
> + if (ret)
> + goto err;
> + }
> +
> + ret = geni_i2c_gpi(gi2c, &msgs[i], &config, &tx_addr, &tx_buf, I2C_WRITE, gi2c->tx_c);
> + if (ret)
> + goto err;
> +
> + if (msgs[i].flags & I2C_M_RD)
> + dma_async_issue_pending(gi2c->rx_c);
> + dma_async_issue_pending(gi2c->tx_c);
> +
> + timeout = wait_for_completion_timeout(&gi2c->done, XFER_TIMEOUT);
> + if (!timeout) {
> + dev_err(gi2c->se.dev, "I2C timeout gpi flags:%d addr:0x%x\n",
> + gi2c->cur->flags, gi2c->cur->addr);
> + ret = gi2c->err = -ETIMEDOUT;
> + goto err;
> + }
> +
> + geni_i2c_gpi_unmap(gi2c, &msgs[i], tx_buf, tx_addr, rx_buf, rx_addr);
> + }
> +
> + return 0;
> +
> +err:
> + dmaengine_terminate_sync(gi2c->rx_c);
> + dmaengine_terminate_sync(gi2c->tx_c);
> + geni_i2c_gpi_unmap(gi2c, &msgs[i], tx_buf, tx_addr, rx_buf, rx_addr);
> + return ret;
> +}
[..]
> +static int setup_gpi_dma(struct geni_i2c_dev *gi2c)
> +{
> + int ret;
> +
> + geni_se_select_mode(&gi2c->se, GENI_GPI_DMA);
> + gi2c->tx_c = dma_request_chan(gi2c->se.dev, "tx");
> + if (IS_ERR(gi2c->tx_c)) {
> + ret = dev_err_probe(gi2c->se.dev, PTR_ERR(gi2c->tx_c),
> + "Failed to get tx DMA ch\n");
> + if (ret < 0)
> + goto err_tx;
> + }
> +
> + gi2c->rx_c = dma_request_chan(gi2c->se.dev, "rx");
> + if (IS_ERR(gi2c->rx_c)) {
> + ret = dev_err_probe(gi2c->se.dev, PTR_ERR(gi2c->rx_c),
> + "Failed to get rx DMA ch\n");
> + if (ret < 0)
> + goto err_rx;
> + }
> +
> + dev_dbg(gi2c->se.dev, "Grabbed GPI dma channels\n");
> + return 0;
> +
> +err_rx:
> + dma_release_channel(gi2c->tx_c);
> + gi2c->tx_c = NULL;
You're not accessing tx_c or rx_c again when returning an error here. So
I don't think there's a reason to clear them.
> +err_tx:
> + gi2c->rx_c = NULL;
> + return ret;
> +}
> +
[..]
> static int geni_i2c_remove(struct platform_device *pdev)
> {
> struct geni_i2c_dev *gi2c = platform_get_drvdata(pdev);
>
> + release_gpi_dma(gi2c);
Your i2c devices aren't torn down until i2c_del_adapter(), so you might
still end up trying to use the two channels here, after releasing them.
In other words, I think you should reorder these.
Regards,
Bjorn
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v5] i2c: qcom-geni: Add support for GPI DMA
2022-01-31 12:04 [PATCH v5] i2c: qcom-geni: Add support for GPI DMA Vinod Koul
2022-02-17 17:35 ` Bjorn Andersson
@ 2022-02-17 17:51 ` Dmitry Baryshkov
2022-02-18 7:06 ` Vinod Koul
1 sibling, 1 reply; 5+ messages in thread
From: Dmitry Baryshkov @ 2022-02-17 17:51 UTC (permalink / raw)
To: Vinod Koul
Cc: Bjorn Andersson, Wolfram Sang, linux-arm-msm, Andy Gross,
Douglas Anderson, Matthias Kaehlcke, linux-i2c, linux-kernel,
Alexey Minnekhanov
On Mon, 31 Jan 2022 at 15:04, Vinod Koul <vkoul@kernel.org> wrote:
>
> QUP Serial engines supports data transfers thru FIFO mode, SE DMA mode and
> lastly GPI DMA mode. Former two are already supported and this adds supports the
> last mode.
>
> In GPI DMA mode, the firmware is issued commands by driver to perform DMA
> and setup the serial port.
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
>
> Changes since v4:
> - Fix buildbot warn
> - Fix flase warn reported by Alexey
> - Fix feedback from Bjorn and cleanup the probe code and add more details
> in changelog
>
> Changes since v3:
> - remove separate tx and rx function for gsi dma and make a common one
> - remove global structs and use local variables instead
>
> drivers/i2c/busses/i2c-qcom-geni.c | 300 ++++++++++++++++++++++++++---
> 1 file changed, 273 insertions(+), 27 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
> index 6d635a7c104c..696253d178a6 100644
> --- a/drivers/i2c/busses/i2c-qcom-geni.c
> +++ b/drivers/i2c/busses/i2c-qcom-geni.c
> @@ -3,7 +3,9 @@
>
> #include <linux/acpi.h>
> #include <linux/clk.h>
> +#include <linux/dmaengine.h>
> #include <linux/dma-mapping.h>
> +#include <linux/dma/qcom-gpi-dma.h>
> #include <linux/err.h>
> #include <linux/i2c.h>
> #include <linux/interrupt.h>
> @@ -48,6 +50,9 @@
> #define LOW_COUNTER_SHFT 10
> #define CYCLE_COUNTER_MSK GENMASK(9, 0)
>
> +#define I2C_PACK_TX BIT(0)
> +#define I2C_PACK_RX BIT(1)
> +
> enum geni_i2c_err_code {
> GP_IRQ0,
> NACK,
> @@ -89,6 +94,9 @@ struct geni_i2c_dev {
> void *dma_buf;
> size_t xfer_len;
> dma_addr_t dma_addr;
> + struct dma_chan *tx_c;
> + struct dma_chan *rx_c;
> + bool gpi_mode;
> };
>
> struct geni_i2c_err_log {
> @@ -456,12 +464,199 @@ static int geni_i2c_tx_one_msg(struct geni_i2c_dev *gi2c, struct i2c_msg *msg,
> return gi2c->err;
> }
>
> +static void i2c_gpi_cb_result(void *cb, const struct dmaengine_result *result)
> +{
> + struct geni_i2c_dev *gi2c = cb;
> +
> + if (result->result != DMA_TRANS_NOERROR) {
> + dev_err(gi2c->se.dev, "DMA txn failed:%d\n", result->result);
> + return;
> + }
> +
> + if (result->residue)
> + dev_dbg(gi2c->se.dev, "DMA xfer has pending: %d\n", result->residue);
> +
> + complete(&gi2c->done);
> +}
> +
> +static void geni_i2c_gpi_unmap(struct geni_i2c_dev *gi2c, struct i2c_msg *msg,
> + void *tx_buf, dma_addr_t tx_addr,
> + void *rx_buf, dma_addr_t rx_addr)
> +{
> + if (tx_buf) {
> + dma_unmap_single(gi2c->se.dev->parent, tx_addr, msg->len, DMA_TO_DEVICE);
> + i2c_put_dma_safe_msg_buf(tx_buf, msg, false);
> + }
> +
> + if (rx_buf) {
> + dma_unmap_single(gi2c->se.dev->parent, rx_addr, msg->len, DMA_FROM_DEVICE);
> + i2c_put_dma_safe_msg_buf(rx_buf, msg, false);
> + }
> +}
> +
> +static int geni_i2c_gpi(struct geni_i2c_dev *gi2c, struct i2c_msg *msg,
> + struct dma_slave_config *config, dma_addr_t *dma_addr_p,
> + void **buf, unsigned int op, struct dma_chan *dma_chan)
> +{
> + struct gpi_i2c_config *peripheral;
> + unsigned int flags;
> + void *dma_buf;
> + dma_addr_t addr;
> + enum dma_data_direction map_dirn;
> + enum dma_transfer_direction dma_dirn;
> + struct dma_async_tx_descriptor *desc;
> + int ret;
> +
> + peripheral = config->peripheral_config;
> +
> + dma_buf = i2c_get_dma_safe_msg_buf(msg, 1);
> + if (!dma_buf)
> + return -ENOMEM;
> +
> + if (op == I2C_WRITE)
> + map_dirn = DMA_TO_DEVICE;
> + else
> + map_dirn = DMA_FROM_DEVICE;
> +
> + addr = dma_map_single(gi2c->se.dev->parent, dma_buf, msg->len, map_dirn);
> + if (dma_mapping_error(gi2c->se.dev->parent, addr)) {
> + i2c_put_dma_safe_msg_buf(dma_buf, msg, false);
> + return -ENOMEM;
> + }
> +
> + /* set the length as message for rx txn */
> + peripheral->rx_len = msg->len;
> + peripheral->op = op;
> +
> + ret = dmaengine_slave_config(dma_chan, config);
> + if (ret) {
> + dev_err(gi2c->se.dev, "dma config error: %d for op:%d\n", ret, op);
> + goto err_config;
> + }
> +
> + peripheral->set_config = 0;
> + peripheral->multi_msg = true;
> + flags = DMA_PREP_INTERRUPT | DMA_CTRL_ACK;
> +
> + if (op == I2C_WRITE)
> + dma_dirn = DMA_MEM_TO_DEV;
> + else
> + dma_dirn = DMA_DEV_TO_MEM;
> +
> + desc = dmaengine_prep_slave_single(dma_chan, addr, msg->len, dma_dirn, flags);
> + if (!desc) {
> + dev_err(gi2c->se.dev, "prep_slave_sg failed\n");
> + ret = -EIO;
> + goto err_config;
> + }
> +
> + desc->callback_result = i2c_gpi_cb_result;
> + desc->callback_param = gi2c;
> +
> + dmaengine_submit(desc);
> + *dma_addr_p = addr;
> +
> + return 0;
> +
> +err_config:
> + dma_unmap_single(gi2c->se.dev->parent, addr, msg->len, map_dirn);
> + i2c_put_dma_safe_msg_buf(dma_buf, msg, false);
> + return ret;
> +}
> +
> +static int geni_i2c_gpi_xfer(struct geni_i2c_dev *gi2c, struct i2c_msg msgs[], int num)
> +{
> + struct dma_slave_config config = {};
> + struct gpi_i2c_config peripheral = {};
> + int i, ret = 0, timeout;
> + dma_addr_t tx_addr, rx_addr;
> + void *tx_buf = NULL, *rx_buf = NULL;
> + const struct geni_i2c_clk_fld *itr = gi2c->clk_fld;
> +
> + config.peripheral_config = &peripheral;
> + config.peripheral_size = sizeof(peripheral);
> +
> + peripheral.pack_enable = I2C_PACK_TX | I2C_PACK_RX;
> + peripheral.cycle_count = itr->t_cycle_cnt;
> + peripheral.high_count = itr->t_high_cnt;
> + peripheral.low_count = itr->t_low_cnt;
> + peripheral.clk_div = itr->clk_div;
> + peripheral.set_config = 1;
> + peripheral.multi_msg = false;
> +
> + for (i = 0; i < num; i++) {
> + gi2c->cur = &msgs[i];
> + dev_dbg(gi2c->se.dev, "msg[%d].len:%d\n", i, gi2c->cur->len);
> +
> + peripheral.stretch = 0;
> + if (i < num - 1)
> + peripheral.stretch = 1;
> +
> + peripheral.addr = msgs[i].addr;
> +
> + if (msgs[i].flags & I2C_M_RD) {
> + ret = geni_i2c_gpi(gi2c, &msgs[i], &config, &rx_addr, &rx_buf, I2C_READ, gi2c->rx_c);
> + if (ret)
> + goto err;
> + }
> +
> + ret = geni_i2c_gpi(gi2c, &msgs[i], &config, &tx_addr, &tx_buf, I2C_WRITE, gi2c->tx_c);
> + if (ret)
> + goto err;
> +
> + if (msgs[i].flags & I2C_M_RD)
> + dma_async_issue_pending(gi2c->rx_c);
> + dma_async_issue_pending(gi2c->tx_c);
> +
> + timeout = wait_for_completion_timeout(&gi2c->done, XFER_TIMEOUT);
> + if (!timeout) {
> + dev_err(gi2c->se.dev, "I2C timeout gpi flags:%d addr:0x%x\n",
> + gi2c->cur->flags, gi2c->cur->addr);
> + ret = gi2c->err = -ETIMEDOUT;
> + goto err;
> + }
> +
> + geni_i2c_gpi_unmap(gi2c, &msgs[i], tx_buf, tx_addr, rx_buf, rx_addr);
> + }
> +
> + return 0;
> +
> +err:
> + dmaengine_terminate_sync(gi2c->rx_c);
> + dmaengine_terminate_sync(gi2c->tx_c);
> + geni_i2c_gpi_unmap(gi2c, &msgs[i], tx_buf, tx_addr, rx_buf, rx_addr);
> + return ret;
> +}
> +
> +static int geni_i2c_fifo_xfer(struct geni_i2c_dev *gi2c,
> + struct i2c_msg msgs[], int num)
> +{
> + int i, ret = 0;
> +
> + for (i = 0; i < num; i++) {
> + u32 m_param = i < (num - 1) ? STOP_STRETCH : 0;
> +
> + m_param |= ((msgs[i].addr << SLV_ADDR_SHFT) & SLV_ADDR_MSK);
> +
> + gi2c->cur = &msgs[i];
> + if (msgs[i].flags & I2C_M_RD)
> + ret = geni_i2c_rx_one_msg(gi2c, &msgs[i], m_param);
> + else
> + ret = geni_i2c_tx_one_msg(gi2c, &msgs[i], m_param);
> +
> + if (ret)
> + break;
I'd suggest to 'return ret' here and change the return line to 'return num'.
> + }
> +
> + return ret;
> +}
> +
> static int geni_i2c_xfer(struct i2c_adapter *adap,
> struct i2c_msg msgs[],
> int num)
> {
> struct geni_i2c_dev *gi2c = i2c_get_adapdata(adap);
> - int i, ret;
> + int ret;
>
> gi2c->err = 0;
> reinit_completion(&gi2c->done);
> @@ -475,22 +670,11 @@ static int geni_i2c_xfer(struct i2c_adapter *adap,
> }
>
> qcom_geni_i2c_conf(gi2c);
> - for (i = 0; i < num; i++) {
> - u32 m_param = i < (num - 1) ? STOP_STRETCH : 0;
> -
> - m_param |= ((msgs[i].addr << SLV_ADDR_SHFT) & SLV_ADDR_MSK);
> -
> - gi2c->cur = &msgs[i];
> - if (msgs[i].flags & I2C_M_RD)
> - ret = geni_i2c_rx_one_msg(gi2c, &msgs[i], m_param);
> - else
> - ret = geni_i2c_tx_one_msg(gi2c, &msgs[i], m_param);
>
> - if (ret)
> - break;
> - }
> - if (ret == 0)
> - ret = num;
> + if (gi2c->gpi_mode)
> + ret = geni_i2c_gpi_xfer(gi2c, msgs, num);
> + else
> + ret = geni_i2c_fifo_xfer(gi2c, msgs, num);
We should return num if ret is 0 here (or in
geni_i2c_fifo_xfer()/geni_i2c_gpi_xfer()).
>
> pm_runtime_mark_last_busy(gi2c->se.dev);
> pm_runtime_put_autosuspend(gi2c->se.dev);
> @@ -517,11 +701,52 @@ static const struct acpi_device_id geni_i2c_acpi_match[] = {
> MODULE_DEVICE_TABLE(acpi, geni_i2c_acpi_match);
> #endif
>
> +static void release_gpi_dma(struct geni_i2c_dev *gi2c)
> +{
> + if (gi2c->rx_c)
> + dma_release_channel(gi2c->rx_c);
> +
> + if (gi2c->tx_c)
> + dma_release_channel(gi2c->tx_c);
> +}
> +
> +static int setup_gpi_dma(struct geni_i2c_dev *gi2c)
> +{
> + int ret;
> +
> + geni_se_select_mode(&gi2c->se, GENI_GPI_DMA);
> + gi2c->tx_c = dma_request_chan(gi2c->se.dev, "tx");
> + if (IS_ERR(gi2c->tx_c)) {
> + ret = dev_err_probe(gi2c->se.dev, PTR_ERR(gi2c->tx_c),
> + "Failed to get tx DMA ch\n");
> + if (ret < 0)
> + goto err_tx;
> + }
> +
> + gi2c->rx_c = dma_request_chan(gi2c->se.dev, "rx");
> + if (IS_ERR(gi2c->rx_c)) {
> + ret = dev_err_probe(gi2c->se.dev, PTR_ERR(gi2c->rx_c),
> + "Failed to get rx DMA ch\n");
> + if (ret < 0)
> + goto err_rx;
> + }
> +
> + dev_dbg(gi2c->se.dev, "Grabbed GPI dma channels\n");
> + return 0;
> +
> +err_rx:
> + dma_release_channel(gi2c->tx_c);
> + gi2c->tx_c = NULL;
> +err_tx:
> + gi2c->rx_c = NULL;
> + return ret;
> +}
> +
> static int geni_i2c_probe(struct platform_device *pdev)
> {
> struct geni_i2c_dev *gi2c;
> struct resource *res;
> - u32 proto, tx_depth;
> + u32 proto, tx_depth, fifo_disable;
> int ret;
> struct device *dev = &pdev->dev;
>
> @@ -601,27 +826,43 @@ static int geni_i2c_probe(struct platform_device *pdev)
> return ret;
> }
> proto = geni_se_read_proto(&gi2c->se);
> - tx_depth = geni_se_get_tx_fifo_depth(&gi2c->se);
> if (proto != GENI_SE_I2C) {
> dev_err(dev, "Invalid proto %d\n", proto);
> geni_se_resources_off(&gi2c->se);
> return -ENXIO;
> }
> - gi2c->tx_wm = tx_depth - 1;
> - geni_se_init(&gi2c->se, gi2c->tx_wm, tx_depth);
> - geni_se_config_packing(&gi2c->se, BITS_PER_BYTE, PACKING_BYTES_PW,
> - true, true, true);
> +
> + fifo_disable = readl_relaxed(gi2c->se.base + GENI_IF_DISABLE_RO) & FIFO_IF_DISABLE;
> + if (fifo_disable) {
> + /* FIFO is disabled, so we can only use GPI DMA */
> + gi2c->gpi_mode = true;
> + ret = setup_gpi_dma(gi2c);
> + if (ret) {
> + dev_err(dev, "Failed to setup GPI DMA mode:%d ret\n", ret);
> + return ret;
> + }
> +
> + dev_dbg(dev, "Using GPI DMA mode for I2C\n");
> + } else {
> + gi2c->gpi_mode = false;
> + tx_depth = geni_se_get_tx_fifo_depth(&gi2c->se);
> + gi2c->tx_wm = tx_depth - 1;
> + geni_se_init(&gi2c->se, gi2c->tx_wm, tx_depth);
> + geni_se_config_packing(&gi2c->se, BITS_PER_BYTE,
> + PACKING_BYTES_PW, true, true, true);
> +
> + dev_dbg(dev, "i2c fifo/se-dma mode. fifo depth:%d\n", tx_depth);
> + }
> +
> ret = geni_se_resources_off(&gi2c->se);
> if (ret) {
> dev_err(dev, "Error turning off resources %d\n", ret);
> - return ret;
> + goto err_dma;
> }
>
> ret = geni_icc_disable(&gi2c->se);
> if (ret)
> - return ret;
> -
> - dev_dbg(dev, "i2c fifo/se-dma mode. fifo depth:%d\n", tx_depth);
> + goto err_dma;
>
> gi2c->suspended = 1;
> pm_runtime_set_suspended(gi2c->se.dev);
> @@ -633,18 +874,23 @@ static int geni_i2c_probe(struct platform_device *pdev)
> if (ret) {
> dev_err(dev, "Error adding i2c adapter %d\n", ret);
> pm_runtime_disable(gi2c->se.dev);
> - return ret;
> + goto err_dma;
> }
>
> dev_dbg(dev, "Geni-I2C adaptor successfully added\n");
>
> return 0;
> +
> +err_dma:
> + release_gpi_dma(gi2c);
> + return ret;
> }
>
> static int geni_i2c_remove(struct platform_device *pdev)
> {
> struct geni_i2c_dev *gi2c = platform_get_drvdata(pdev);
>
> + release_gpi_dma(gi2c);
> i2c_del_adapter(&gi2c->adap);
> pm_runtime_disable(gi2c->se.dev);
> return 0;
> --
> 2.31.1
>
--
With best wishes
Dmitry
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v5] i2c: qcom-geni: Add support for GPI DMA
2022-02-17 17:35 ` Bjorn Andersson
@ 2022-02-18 6:33 ` Vinod Koul
0 siblings, 0 replies; 5+ messages in thread
From: Vinod Koul @ 2022-02-18 6:33 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Wolfram Sang, linux-arm-msm, Andy Gross, Douglas Anderson,
Matthias Kaehlcke, linux-i2c, linux-kernel, Alexey Minnekhanov
On 17-02-22, 09:35, Bjorn Andersson wrote:
> > +static void i2c_gpi_cb_result(void *cb, const struct dmaengine_result *result)
> > +{
> > + struct geni_i2c_dev *gi2c = cb;
> > +
> > + if (result->result != DMA_TRANS_NOERROR) {
> > + dev_err(gi2c->se.dev, "DMA txn failed:%d\n", result->result);
>
> Iiuc the API the expectation is that if we get !NOERROR we shouldn't
> expect to get NOERROR after that.
>
> If so we're just returning here and leaving geni_i2c_gpi_xfer() to just
> timeout in a HZ or so. Given that xfer happens under the adaptor lock,
> how about carrying an error in geni_i2c_dev and complete(&done) here as
> well?
Yes we should call complete for errors too, will add that
> > +static int setup_gpi_dma(struct geni_i2c_dev *gi2c)
> > +{
> > + int ret;
> > +
> > + geni_se_select_mode(&gi2c->se, GENI_GPI_DMA);
> > + gi2c->tx_c = dma_request_chan(gi2c->se.dev, "tx");
> > + if (IS_ERR(gi2c->tx_c)) {
> > + ret = dev_err_probe(gi2c->se.dev, PTR_ERR(gi2c->tx_c),
> > + "Failed to get tx DMA ch\n");
> > + if (ret < 0)
> > + goto err_tx;
> > + }
> > +
> > + gi2c->rx_c = dma_request_chan(gi2c->se.dev, "rx");
> > + if (IS_ERR(gi2c->rx_c)) {
> > + ret = dev_err_probe(gi2c->se.dev, PTR_ERR(gi2c->rx_c),
> > + "Failed to get rx DMA ch\n");
> > + if (ret < 0)
> > + goto err_rx;
> > + }
> > +
> > + dev_dbg(gi2c->se.dev, "Grabbed GPI dma channels\n");
> > + return 0;
> > +
> > +err_rx:
> > + dma_release_channel(gi2c->tx_c);
> > + gi2c->tx_c = NULL;
>
> You're not accessing tx_c or rx_c again when returning an error here. So
> I don't think there's a reason to clear them.
Will drop that
> > static int geni_i2c_remove(struct platform_device *pdev)
> > {
> > struct geni_i2c_dev *gi2c = platform_get_drvdata(pdev);
> >
> > + release_gpi_dma(gi2c);
>
> Your i2c devices aren't torn down until i2c_del_adapter(), so you might
> still end up trying to use the two channels here, after releasing them.
>
> In other words, I think you should reorder these.
Agreed it should be other way round!
Thanks
--
~Vinod
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v5] i2c: qcom-geni: Add support for GPI DMA
2022-02-17 17:51 ` Dmitry Baryshkov
@ 2022-02-18 7:06 ` Vinod Koul
0 siblings, 0 replies; 5+ messages in thread
From: Vinod Koul @ 2022-02-18 7:06 UTC (permalink / raw)
To: Dmitry Baryshkov
Cc: Bjorn Andersson, Wolfram Sang, linux-arm-msm, Andy Gross,
Douglas Anderson, Matthias Kaehlcke, linux-i2c, linux-kernel,
Alexey Minnekhanov
On 17-02-22, 20:51, Dmitry Baryshkov wrote:
> On Mon, 31 Jan 2022 at 15:04, Vinod Koul <vkoul@kernel.org> wrote:
> > +static int geni_i2c_fifo_xfer(struct geni_i2c_dev *gi2c,
> > + struct i2c_msg msgs[], int num)
> > +{
> > + int i, ret = 0;
> > +
> > + for (i = 0; i < num; i++) {
> > + u32 m_param = i < (num - 1) ? STOP_STRETCH : 0;
> > +
> > + m_param |= ((msgs[i].addr << SLV_ADDR_SHFT) & SLV_ADDR_MSK);
> > +
> > + gi2c->cur = &msgs[i];
> > + if (msgs[i].flags & I2C_M_RD)
> > + ret = geni_i2c_rx_one_msg(gi2c, &msgs[i], m_param);
> > + else
> > + ret = geni_i2c_tx_one_msg(gi2c, &msgs[i], m_param);
> > +
> > + if (ret)
> > + break;
>
> I'd suggest to 'return ret' here and change the return line to 'return num'.
Done
> > static int geni_i2c_xfer(struct i2c_adapter *adap,
> > struct i2c_msg msgs[],
> > int num)
> > {
> > struct geni_i2c_dev *gi2c = i2c_get_adapdata(adap);
> > - int i, ret;
> > + int ret;
> >
> > gi2c->err = 0;
> > reinit_completion(&gi2c->done);
> > @@ -475,22 +670,11 @@ static int geni_i2c_xfer(struct i2c_adapter *adap,
> > }
> >
> > qcom_geni_i2c_conf(gi2c);
> > - for (i = 0; i < num; i++) {
> > - u32 m_param = i < (num - 1) ? STOP_STRETCH : 0;
> > -
> > - m_param |= ((msgs[i].addr << SLV_ADDR_SHFT) & SLV_ADDR_MSK);
> > -
> > - gi2c->cur = &msgs[i];
> > - if (msgs[i].flags & I2C_M_RD)
> > - ret = geni_i2c_rx_one_msg(gi2c, &msgs[i], m_param);
> > - else
> > - ret = geni_i2c_tx_one_msg(gi2c, &msgs[i], m_param);
> >
> > - if (ret)
> > - break;
> > - }
> > - if (ret == 0)
> > - ret = num;
> > + if (gi2c->gpi_mode)
> > + ret = geni_i2c_gpi_xfer(gi2c, msgs, num);
> > + else
> > + ret = geni_i2c_fifo_xfer(gi2c, msgs, num);
>
> We should return num if ret is 0 here (or in
> geni_i2c_fifo_xfer()/geni_i2c_gpi_xfer()).
I have picked your fix for that!
--
~Vinod
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2022-02-18 7:06 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-01-31 12:04 [PATCH v5] i2c: qcom-geni: Add support for GPI DMA Vinod Koul
2022-02-17 17:35 ` Bjorn Andersson
2022-02-18 6:33 ` Vinod Koul
2022-02-17 17:51 ` Dmitry Baryshkov
2022-02-18 7:06 ` Vinod Koul
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).