From: Lukas Wunner <lukas@wunner.de>
To: "Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>
Cc: linux-serial@vger.kernel.org, Jiri Slaby <jirislaby@kernel.org>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
linux-kernel@vger.kernel.org, Johan Hovold <johan@kernel.org>,
Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
Heikki Krogerus <heikki.krogerus@linux.intel.com>,
Raymond Tan <raymond.tan@intel.com>
Subject: Re: [PATCH 2/7] serial: 8250_dwlib: RS485 HW full duplex support
Date: Sun, 6 Mar 2022 19:51:49 +0100 [thread overview]
Message-ID: <20220306185149.GB19394@wunner.de> (raw)
In-Reply-To: <20220302095606.14818-3-ilpo.jarvinen@linux.intel.com>
On Wed, Mar 02, 2022 at 11:56:01AM +0200, Ilpo Järvinen wrote:
> @@ -110,9 +110,14 @@ static int dw8250_rs485_config(struct uart_port *p, struct serial_rs485 *rs485)
>
> if (rs485->flags & SER_RS485_ENABLED) {
> /* Clearing unsupported flags. */
> - rs485->flags &= SER_RS485_ENABLED;
> -
> - tcr |= DW_UART_TCR_RS485_EN | DW_UART_TCR_XFER_MODE_DE_OR_RE;
> + rs485->flags &= SER_RS485_ENABLED | SER_RS485_RX_DURING_TX;
> + tcr |= DW_UART_TCR_RS485_EN;
> +
> + if (rs485->flags & SER_RS485_RX_DURING_TX) {
> + tcr |= DW_UART_TCR_XFER_MODE_DE_DURING_RE;
> + } else {
> + tcr |= DW_UART_TCR_XFER_MODE_DE_OR_RE;
> + }
This patch deletes lines introduced by the preceding patch.
I'd just squash the two together, I don't see much value in
introducing full duplex support in a separate patch.
Thanks,
Lukas
next prev parent reply other threads:[~2022-03-06 18:51 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-03-02 9:55 [PATCH 0/7] Add RS485 support to DW UART Ilpo Järvinen
2022-03-02 9:56 ` [PATCH 1/7] serial: 8250_dwlib: RS485 HW half duplex support Ilpo Järvinen
2022-03-06 18:48 ` Lukas Wunner
2022-03-06 22:07 ` Andy Shevchenko
2022-03-07 9:19 ` Ilpo Järvinen
2022-03-07 19:18 ` Lukas Wunner
2022-03-07 19:39 ` Andy Shevchenko
2022-03-08 12:16 ` Ilpo Järvinen
2022-03-08 12:22 ` Lukas Wunner
2022-03-08 12:59 ` Ilpo Järvinen
2022-03-08 14:50 ` Lukas Wunner
2022-03-08 14:53 ` Andy Shevchenko
2022-03-08 20:30 ` Lukas Wunner
2022-03-09 9:51 ` Ilpo Järvinen
2022-03-07 10:54 ` Ilpo Järvinen
2022-03-09 8:52 ` Lukas Wunner
2022-03-09 12:19 ` Ilpo Järvinen
2022-03-09 12:59 ` Lukas Wunner
2022-03-02 9:56 ` [PATCH 2/7] serial: 8250_dwlib: RS485 HW full " Ilpo Järvinen
2022-03-06 18:51 ` Lukas Wunner [this message]
2022-03-07 9:22 ` Ilpo Järvinen
2022-03-02 9:56 ` [RFC PATCH 3/7] serial: 8250_dwlib: Implement SW half " Ilpo Järvinen
2022-03-06 19:21 ` Lukas Wunner
2022-03-06 22:13 ` Andy Shevchenko
2022-03-02 9:56 ` [PATCH 4/7] dt_bindings: snps-dw-apb-uart: Add RS485 Ilpo Järvinen
2022-03-02 17:47 ` Rob Herring
2022-03-02 9:56 ` [RFC PATCH 5/7] serial: termbits: ADDRB to indicate 9th bit addressing mode Ilpo Järvinen
2022-03-02 9:56 ` [RFC PATCH 6/7] serial: General support for multipoint addresses Ilpo Järvinen
2022-03-06 19:40 ` Lukas Wunner
2022-03-07 9:48 ` Ilpo Järvinen
2022-03-09 19:05 ` Lukas Wunner
2022-03-10 12:29 ` Ilpo Järvinen
2022-03-10 14:09 ` Andy Shevchenko
2022-03-02 9:56 ` [RFC PATCH 7/7] serial: 8250_dwlib: Support for 9th bit multipoint addressing Ilpo Järvinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220306185149.GB19394@wunner.de \
--to=lukas@wunner.de \
--cc=andriy.shevchenko@linux.intel.com \
--cc=gregkh@linuxfoundation.org \
--cc=heikki.krogerus@linux.intel.com \
--cc=ilpo.jarvinen@linux.intel.com \
--cc=jirislaby@kernel.org \
--cc=johan@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=raymond.tan@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).