* [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc
@ 2022-04-01 20:10 Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 01/10] arm64: dts: qcom: msm8953: do not use underscore in node name Krzysztof Kozlowski
` (9 more replies)
0 siblings, 10 replies; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-01 20:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
Cc: Krzysztof Kozlowski
Hi,
Convert to DT schema clock/qcom,rpmcc and soc/qcom,smd. The SoC and clock
schema patches are independent, although Rob's bot might complain about
compatible without schema, so maybe let's take them via one tree?
The DTS patches are independent fixes/cleanups for issues pointed out by this
schema and can be taken independently. Not tested, although no impact on
functionality is expected.
Best regards,
Krzysztof
Krzysztof Kozlowski (10):
arm64: dts: qcom: msm8953: do not use underscore in node name
arm64: dts: qcom: msm8994: remove SMD qcom,local-pid property
arm64: dts: qcom: add RPM clock controller fallback compatible
ARM: dts: qcom: msm8974-lge-nexus5: move gpio-keys out of soc
ARM: dts: qcom: msm8974-samsung-klte: move gpio-keys out of soc
ARM: dts: qcom: msm8974: override nodes by label
ARM: dts: qcom: do not use underscore in node name
dt-bindings: soc: qcom,smd: convert to dtschema
dt-bindings: clock: qcom,rpmcc: convert to dtschema
dt-bindings: clock: qcom,rpmcc: add clocks property
.../devicetree/bindings/clock/qcom,rpmcc.txt | 63 -
.../devicetree/bindings/clock/qcom,rpmcc.yaml | 75 ++
.../regulator/qcom,smd-rpm-regulator.yaml | 2 +-
.../bindings/remoteproc/qcom,q6v5.txt | 2 +-
.../bindings/remoteproc/qcom,wcnss-pil.txt | 2 +-
.../bindings/soc/qcom/qcom,smd-rpm.yaml | 8 +-
.../devicetree/bindings/soc/qcom/qcom,smd.txt | 98 --
.../bindings/soc/qcom/qcom,smd.yaml | 137 ++
arch/arm/boot/dts/qcom-apq8064.dtsi | 8 +-
.../arm/boot/dts/qcom-apq8074-dragonboard.dts | 614 +++++----
arch/arm/boot/dts/qcom-apq8084.dtsi | 2 +-
.../boot/dts/qcom-msm8974-fairphone-fp2.dts | 581 +++++----
.../qcom-msm8974-lge-nexus5-hammerhead.dts | 1105 ++++++++--------
.../boot/dts/qcom-msm8974-samsung-klte.dts | 1127 ++++++++---------
.../dts/qcom-msm8974-sony-xperia-amami.dts | 569 ++++-----
.../dts/qcom-msm8974-sony-xperia-castor.dts | 908 +++++++------
.../dts/qcom-msm8974-sony-xperia-honami.dts | 636 +++++-----
arch/arm/boot/dts/qcom-msm8974.dtsi | 16 +-
arch/arm64/boot/dts/qcom/msm8916.dtsi | 2 +-
arch/arm64/boot/dts/qcom/msm8953.dtsi | 4 +-
arch/arm64/boot/dts/qcom/msm8992.dtsi | 2 +-
arch/arm64/boot/dts/qcom/msm8994.dtsi | 3 +-
arch/arm64/boot/dts/qcom/msm8996.dtsi | 2 +-
arch/arm64/boot/dts/qcom/qcs404.dtsi | 2 +-
24 files changed, 3000 insertions(+), 2968 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
create mode 100644 Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml
delete mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt
create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd.yaml
--
2.32.0
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH 01/10] arm64: dts: qcom: msm8953: do not use underscore in node name
2022-04-01 20:10 [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc Krzysztof Kozlowski
@ 2022-04-01 20:10 ` Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 02/10] arm64: dts: qcom: msm8994: remove SMD qcom,local-pid property Krzysztof Kozlowski
` (8 subsequent siblings)
9 siblings, 0 replies; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-01 20:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
Cc: Krzysztof Kozlowski
Align RPM requests node with DT schema by using hyphen instead of
underscore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8953.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
index 431228faacdd..aca13760bb75 100644
--- a/arch/arm64/boot/dts/qcom/msm8953.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
@@ -321,7 +321,7 @@ rpm {
qcom,ipc = <&apcs 8 0>;
qcom,smd-edge = <15>;
- rpm_requests: rpm_requests {
+ rpm_requests: rpm-requests {
compatible = "qcom,rpm-msm8953";
qcom,smd-channels = "rpm_requests";
--
2.32.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 02/10] arm64: dts: qcom: msm8994: remove SMD qcom,local-pid property
2022-04-01 20:10 [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 01/10] arm64: dts: qcom: msm8953: do not use underscore in node name Krzysztof Kozlowski
@ 2022-04-01 20:10 ` Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 03/10] arm64: dts: qcom: add RPM clock controller fallback compatible Krzysztof Kozlowski
` (7 subsequent siblings)
9 siblings, 0 replies; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-01 20:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
Cc: Krzysztof Kozlowski
The Qualcomm SMD does not use qcom,local-pid property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8994.dtsi | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi
index 8c1dc5155b71..1ff7e2c03ce3 100644
--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -233,7 +233,6 @@ rpm {
interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&apcs 8 0>;
qcom,smd-edge = <15>;
- qcom,local-pid = <0>;
qcom,remote-pid = <6>;
rpm_requests: rpm-requests {
--
2.32.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 03/10] arm64: dts: qcom: add RPM clock controller fallback compatible
2022-04-01 20:10 [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 01/10] arm64: dts: qcom: msm8953: do not use underscore in node name Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 02/10] arm64: dts: qcom: msm8994: remove SMD qcom,local-pid property Krzysztof Kozlowski
@ 2022-04-01 20:10 ` Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 04/10] ARM: dts: qcom: msm8974-lge-nexus5: move gpio-keys out of soc Krzysztof Kozlowski
` (6 subsequent siblings)
9 siblings, 0 replies; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-01 20:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
Cc: Krzysztof Kozlowski
The bindings require a fallback compatible to RPM clock controller.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8916.dtsi | 2 +-
arch/arm64/boot/dts/qcom/msm8953.dtsi | 2 +-
arch/arm64/boot/dts/qcom/msm8992.dtsi | 2 +-
arch/arm64/boot/dts/qcom/msm8994.dtsi | 2 +-
arch/arm64/boot/dts/qcom/msm8996.dtsi | 2 +-
arch/arm64/boot/dts/qcom/qcs404.dtsi | 2 +-
6 files changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index e34963505e07..cf0482fdf69d 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -299,7 +299,7 @@ rpm_requests: rpm-requests {
qcom,smd-channels = "rpm_requests";
rpmcc: clock-controller {
- compatible = "qcom,rpmcc-msm8916";
+ compatible = "qcom,rpmcc-msm8916", "qcom,rpmcc";
#clock-cells = <1>;
};
diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
index aca13760bb75..4fa0091d7a5e 100644
--- a/arch/arm64/boot/dts/qcom/msm8953.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
@@ -326,7 +326,7 @@ rpm_requests: rpm-requests {
qcom,smd-channels = "rpm_requests";
rpmcc: rpmcc {
- compatible = "qcom,rpmcc-msm8953";
+ compatible = "qcom,rpmcc-msm8953", "qcom,rpmcc";
clocks = <&xo_board>;
clock-names = "xo";
#clock-cells = <1>;
diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi
index 58fe58cc7703..c286381240ed 100644
--- a/arch/arm64/boot/dts/qcom/msm8992.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi
@@ -11,7 +11,7 @@
/delete-node/ &cpu7_map;
&rpmcc {
- compatible = "qcom,rpmcc-msm8992";
+ compatible = "qcom,rpmcc-msm8992", "qcom,rpmcc";
};
&tcsr_mutex {
diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi
index 1ff7e2c03ce3..a36b1c7cf10e 100644
--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -240,7 +240,7 @@ rpm_requests: rpm-requests {
qcom,smd-channels = "rpm_requests";
rpmcc: rpmcc {
- compatible = "qcom,rpmcc-msm8994";
+ compatible = "qcom,rpmcc-msm8994", "qcom,rpmcc";
#clock-cells = <1>;
};
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index f0f81c23c16f..527afc90d9ef 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -456,7 +456,7 @@ rpm_requests: rpm-requests {
qcom,glink-channels = "rpm_requests";
rpmcc: qcom,rpmcc {
- compatible = "qcom,rpmcc-msm8996";
+ compatible = "qcom,rpmcc-msm8996", "qcom,rpmcc";
#clock-cells = <1>;
};
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index 3f06f7cd3cf2..f0ade6a03208 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -226,7 +226,7 @@ rpm_requests: glink-channel {
qcom,glink-channels = "rpm_requests";
rpmcc: clock-controller {
- compatible = "qcom,rpmcc-qcs404";
+ compatible = "qcom,rpmcc-qcs404", "qcom,rpmcc";
#clock-cells = <1>;
};
--
2.32.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 04/10] ARM: dts: qcom: msm8974-lge-nexus5: move gpio-keys out of soc
2022-04-01 20:10 [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc Krzysztof Kozlowski
` (2 preceding siblings ...)
2022-04-01 20:10 ` [PATCH 03/10] arm64: dts: qcom: add RPM clock controller fallback compatible Krzysztof Kozlowski
@ 2022-04-01 20:10 ` Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 05/10] ARM: dts: qcom: msm8974-samsung-klte: " Krzysztof Kozlowski
` (5 subsequent siblings)
9 siblings, 0 replies; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-01 20:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
Cc: Krzysztof Kozlowski
The GPIO keys are not part of SoC and they should be defined inside of
the root node.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../qcom-msm8974-lge-nexus5-hammerhead.dts | 42 +++++++++----------
1 file changed, 21 insertions(+), 21 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index 069136170198..6d5fb60e798f 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -19,6 +19,27 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_pin_a>;
+
+ volume-up {
+ label = "volume_up";
+ gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ volume-down {
+ label = "volume_down";
+ gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
+
smd {
rpm {
rpm_requests {
@@ -448,27 +469,6 @@ bcrmf@1 {
};
};
- gpio-keys {
- compatible = "gpio-keys";
-
- pinctrl-names = "default";
- pinctrl-0 = <&gpio_keys_pin_a>;
-
- volume-up {
- label = "volume_up";
- gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
- linux,input-type = <1>;
- linux,code = <KEY_VOLUMEUP>;
- };
-
- volume-down {
- label = "volume_down";
- gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
- linux,input-type = <1>;
- linux,code = <KEY_VOLUMEDOWN>;
- };
- };
-
serial@f9960000 {
status = "okay";
--
2.32.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 05/10] ARM: dts: qcom: msm8974-samsung-klte: move gpio-keys out of soc
2022-04-01 20:10 [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc Krzysztof Kozlowski
` (3 preceding siblings ...)
2022-04-01 20:10 ` [PATCH 04/10] ARM: dts: qcom: msm8974-lge-nexus5: move gpio-keys out of soc Krzysztof Kozlowski
@ 2022-04-01 20:10 ` Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 06/10] ARM: dts: qcom: msm8974: override nodes by label Krzysztof Kozlowski
` (4 subsequent siblings)
9 siblings, 0 replies; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-01 20:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
Cc: Krzysztof Kozlowski
The GPIO keys are not part of SoC and they should be defined inside of
the root node.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../boot/dts/qcom-msm8974-samsung-klte.dts | 64 +++++++++----------
1 file changed, 32 insertions(+), 32 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
index 96e1c978b878..6e036a440532 100644
--- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
@@ -20,6 +20,38 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_pin_a>;
+
+ volume-down {
+ label = "volume_down";
+ gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ debounce-interval = <15>;
+ };
+
+ home-key {
+ label = "home_key";
+ gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_HOMEPAGE>;
+ wakeup-source;
+ debounce-interval = <15>;
+ };
+
+ volume-up {
+ label = "volume_up";
+ gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEUP>;
+ debounce-interval = <15>;
+ };
+ };
+
smd {
rpm {
rpm_requests {
@@ -347,38 +379,6 @@ bluetooth {
};
};
- gpio-keys {
- compatible = "gpio-keys";
-
- pinctrl-names = "default";
- pinctrl-0 = <&gpio_keys_pin_a>;
-
- volume-down {
- label = "volume_down";
- gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>;
- linux,input-type = <1>;
- linux,code = <KEY_VOLUMEDOWN>;
- debounce-interval = <15>;
- };
-
- home-key {
- label = "home_key";
- gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>;
- linux,input-type = <1>;
- linux,code = <KEY_HOMEPAGE>;
- wakeup-source;
- debounce-interval = <15>;
- };
-
- volume-up {
- label = "volume_up";
- gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>;
- linux,input-type = <1>;
- linux,code = <KEY_VOLUMEUP>;
- debounce-interval = <15>;
- };
- };
-
pinctrl@fd510000 {
blsp2_uart8_pins_active: blsp2-uart8-pins-active {
pins = "gpio45", "gpio46", "gpio47", "gpio48";
--
2.32.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 06/10] ARM: dts: qcom: msm8974: override nodes by label
2022-04-01 20:10 [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc Krzysztof Kozlowski
` (4 preceding siblings ...)
2022-04-01 20:10 ` [PATCH 05/10] ARM: dts: qcom: msm8974-samsung-klte: " Krzysztof Kozlowski
@ 2022-04-01 20:10 ` Krzysztof Kozlowski
2022-04-18 15:10 ` Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 07/10] ARM: dts: qcom: do not use underscore in node name Krzysztof Kozlowski
` (3 subsequent siblings)
9 siblings, 1 reply; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-01 20:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
Cc: Krzysztof Kozlowski
Using node paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time). This also reduces the indentation making the code
easier to read.
Re-order the overrides by label name. The pre/post DTBS are the same.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../arm/boot/dts/qcom-apq8074-dragonboard.dts | 614 +++++-----
.../boot/dts/qcom-msm8974-fairphone-fp2.dts | 581 +++++----
.../qcom-msm8974-lge-nexus5-hammerhead.dts | 1075 ++++++++--------
.../boot/dts/qcom-msm8974-samsung-klte.dts | 1083 ++++++++---------
.../dts/qcom-msm8974-sony-xperia-amami.dts | 569 +++++----
.../dts/qcom-msm8974-sony-xperia-castor.dts | 908 +++++++-------
.../dts/qcom-msm8974-sony-xperia-honami.dts | 636 +++++-----
arch/arm/boot/dts/qcom-msm8974.dtsi | 16 +-
8 files changed, 2730 insertions(+), 2752 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
index 83793b835d40..4c510701ff83 100644
--- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
@@ -17,330 +17,324 @@ chosen {
stdout-path = "serial0:115200n8";
};
- soc {
- serial@f991e000 {
- status = "okay";
+};
+
+&blsp_i2c11 {
+ status = "okay";
+ clock-frequency = <200000>;
+ pinctrl-0 = <&i2c11_pins>;
+ pinctrl-names = "default";
+
+ eeprom: eeprom@52 {
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ pagesize = <32>;
+ read-only;
+ };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&msmgpio {
+ i2c11_pins: i2c11 {
+ mux {
+ pins = "gpio83", "gpio84";
+ function = "blsp_i2c11";
};
+ };
- sdhci@f9824900 {
- bus-width = <8>;
- non-removable;
- status = "okay";
+ spi8_default: spi8_default {
+ mosi {
+ pins = "gpio45";
+ function = "blsp_spi8";
+ };
+ miso {
+ pins = "gpio46";
+ function = "blsp_spi8";
+ };
+ cs {
+ pins = "gpio47";
+ function = "blsp_spi8";
+ };
+ clk {
+ pins = "gpio48";
+ function = "blsp_spi8";
+ };
+ };
- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
};
+ };
- sdhci@f98a4900 {
- cd-gpios = <&msmgpio 62 0x1>;
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
- bus-width = <4>;
- status = "okay";
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
- vmmc-supply = <&pm8941_l21>;
- vqmmc-supply = <&pm8941_l13>;
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <10>;
+ bias-disable;
};
- usb@f9a55000 {
- status = "okay";
- phys = <&usb_hs2_phy>;
- phy-select = <&tcsr 0xb000 1>;
- extcon = <&smbb>, <&usb_id>;
- vbus-supply = <&chg_otg>;
- hnp-disable;
- srp-disable;
- adp-disable;
- ulpi {
- phy@b {
- status = "okay";
- v3p3-supply = <&pm8941_l24>;
- v1p8-supply = <&pm8941_l6>;
- extcon = <&smbb>;
- qcom,init-seq = /bits/ 8 <0x1 0x63>;
- };
- };
- };
-
-
- pinctrl@fd510000 {
- i2c11_pins: i2c11 {
- mux {
- pins = "gpio83", "gpio84";
- function = "blsp_i2c11";
- };
- };
-
- spi8_default: spi8_default {
- mosi {
- pins = "gpio45";
- function = "blsp_spi8";
- };
- miso {
- pins = "gpio46";
- function = "blsp_spi8";
- };
- cs {
- pins = "gpio47";
- function = "blsp_spi8";
- };
- clk {
- pins = "gpio48";
- function = "blsp_spi8";
- };
- };
-
- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
-
- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
- };
-
- sdhc2_cd_pin_a: sdhc2-cd-pin-active {
- pins = "gpio62";
- function = "gpio";
-
- drive-strength = <2>;
- bias-disable;
- };
-
- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <10>;
- bias-disable;
- };
-
- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
- };
- };
- };
-
- i2c@f9967000 {
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+};
+
+&otg {
+ status = "okay";
+ phys = <&usb_hs2_phy>;
+ phy-select = <&tcsr 0xb000 1>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ ulpi {
+ phy@b {
status = "okay";
- clock-frequency = <200000>;
- pinctrl-0 = <&i2c11_pins>;
- pinctrl-names = "default";
+ v3p3-supply = <&pm8941_l24>;
+ v1p8-supply = <&pm8941_l6>;
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x63>;
+ };
+ };
+};
+
+&rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };
- eeprom: eeprom@52 {
- compatible = "atmel,24c128";
- reg = <0x52>;
- pagesize = <32>;
- read-only;
- };
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
};
};
- smd {
- rpm {
- rpm_requests {
- pm8841-regulators {
- s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s3 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s4 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
- };
-
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vin_5vs-supply = <&pm8941_5v>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l10 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-boot-on;
- regulator-system-load = <200000>;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l23 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vin_5vs-supply = <&pm8941_5v>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
};
};
};
+
+&sdhci1 {
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci3 {
+ cd-gpios = <&msmgpio 62 0x1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+ bus-width = <4>;
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts b/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
index 6d77e0f8ca4d..f72a53a0e962 100644
--- a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
@@ -55,345 +55,340 @@ vibrator {
vcc-supply = <&pm8941_l18>;
};
- smd {
- rpm {
- rpm_requests {
- pm8841-regulators {
- s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s3 {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- };
- };
-
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
- vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
- vdd_l21-supply = <&vreg_boost>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
-
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l10 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l11 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1350000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <3350000>;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- regulator-system-load = <200000>;
- regulator-allow-set-load;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l23 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&imem {
+ status = "okay";
+
+ reboot-mode {
+ mode-normal = <0x77665501>;
+ mode-bootloader = <0x77665500>;
+ mode-recovery = <0x77665502>;
+ };
+};
+
+&msmgpio {
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
+ wcnss_pin_a: wcnss-pin-active {
+ wlan {
+ pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+ function = "wlan";
+
+ drive-strength = <6>;
+ bias-pull-down;
+ };
+
+ bt {
+ pins = "gpio35", "gpio43", "gpio44";
+ function = "bt";
+
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ fm {
+ pins = "gpio41", "gpio42";
+ function = "fm";
+
+ drive-strength = <2>;
+ bias-pull-down;
};
};
};
-&soc {
- serial@f991e000 {
- status = "okay";
+&otg {
+ status = "okay";
+
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ ulpi {
+ phy@a {
+ status = "okay";
+
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
+
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+ };
};
+};
- remoteproc@fb21b000 {
- status = "okay";
+&pronto {
+ status = "okay";
- vddmx-supply = <&pm8841_s1>;
- vddcx-supply = <&pm8841_s2>;
+ vddmx-supply = <&pm8841_s1>;
+ vddcx-supply = <&pm8841_s2>;
- pinctrl-names = "default";
- pinctrl-0 = <&wcnss_pin_a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wcnss_pin_a>;
- smd-edge {
- qcom,remote-pid = <4>;
- label = "pronto";
+ smd-edge {
+ qcom,remote-pid = <4>;
+ label = "pronto";
- wcnss {
- status = "okay";
- };
+ wcnss {
+ status = "okay";
};
};
+};
- pinctrl@fd510000 {
- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
+&rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };
- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
};
- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <10>;
- bias-disable;
- };
+ s3 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
+ };
- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
- };
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+
+ regulator-always-on;
+ regulator-boot-on;
};
- wcnss_pin_a: wcnss-pin-active {
- wlan {
- pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
- function = "wlan";
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
- drive-strength = <6>;
- bias-pull-down;
- };
+ regulator-boot-on;
+ };
- bt {
- pins = "gpio35", "gpio43", "gpio44";
- function = "bt";
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- drive-strength = <2>;
- bias-pull-down;
- };
+ regulator-always-on;
+ regulator-boot-on;
+ };
- fm {
- pins = "gpio41", "gpio42";
- function = "fm";
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
- drive-strength = <2>;
- bias-pull-down;
- };
+ regulator-always-on;
+ regulator-boot-on;
};
- };
- sdhci@f9824900 {
- status = "okay";
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ l3 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
- bus-width = <8>;
- non-removable;
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
- };
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- sdhci@f98a4900 {
- status = "okay";
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- vmmc-supply = <&pm8941_l21>;
- vqmmc-supply = <&pm8941_l13>;
+ regulator-boot-on;
+ };
- bus-width = <4>;
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>;
- };
+ regulator-boot-on;
+ };
+
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
- usb@f9a55000 {
- status = "okay";
+ l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
- extcon = <&smbb>, <&usb_id>;
- vbus-supply = <&chg_otg>;
+ l11 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1350000>;
+ };
- hnp-disable;
- srp-disable;
- adp-disable;
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- ulpi {
- phy@a {
- status = "okay";
+ regulator-always-on;
+ regulator-boot-on;
+ };
- v1p8-supply = <&pm8941_l6>;
- v3p3-supply = <&pm8941_l24>;
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
- extcon = <&smbb>;
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ regulator-boot-on;
};
- };
- imem@fe805000 {
- status = "okay";
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
- reboot-mode {
- mode-normal = <0x77665501>;
- mode-bootloader = <0x77665500>;
- mode-recovery = <0x77665502>;
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <3350000>;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ regulator-allow-set-load;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
};
};
};
+&sdhci1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci3 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+
+ bus-width = <4>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>;
+};
+
&spmi_bus {
pm8941@0 {
gpios@c000 {
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index 6d5fb60e798f..a72ef21b2fc7 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -40,209 +40,6 @@ volume-down {
};
};
- smd {
- rpm {
- rpm_requests {
- pm8841-regulators {
- s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s3 {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s4 {
- regulator-min-microvolt = <815000>;
- regulator-max-microvolt = <900000>;
- };
- };
-
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
- vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
- vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
- vdd_l21-supply = <&vreg_boost>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
-
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l10 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- regulator-system-load = <200000>;
- regulator-allow-set-load;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l23 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
- };
- };
-
vreg_wlan: wlan-regulator {
compatible = "regulator-fixed";
@@ -256,464 +53,682 @@ vreg_wlan: wlan-regulator {
pinctrl-names = "default";
pinctrl-0 = <&wlan_regulator_pin>;
};
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_pin_a>;
+
+ volume-up {
+ label = "volume_up";
+ gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ volume-down {
+ label = "volume_down";
+ gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
};
-&soc {
- serial@f991d000 {
- status = "okay";
+&blsp1_uart1 {
+ status = "okay";
+};
+
+&blsp2_uart10 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp2_uart10_pin_a>;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <3000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_pin>;
+
+ host-wakeup-gpios = <&msmgpio 42 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&msmgpio 41 GPIO_ACTIVE_HIGH>;
};
+};
- pinctrl@fd510000 {
- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
+&blsp_i2c1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ clock-frequency = <100000>;
+ qcom,src-freq = <50000000>;
- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
+ charger: bq24192@6b {
+ compatible = "ti,bq24192";
+ reg = <0x6b>;
+ interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
+
+ omit-battery-class;
+
+ usb_otg_vbus: usb-otg-vbus { };
+ };
+
+ fuelgauge: max17048@36 {
+ compatible = "maxim,max17048";
+ reg = <0x36>;
+
+ maxim,double-soc;
+ maxim,rcomp = /bits/ 8 <0x4d>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&fuelgauge_pin>;
+
+ maxim,alert-low-soc-level = <2>;
+ };
+};
+
+&blsp_i2c2 {
+ status = "okay";
+
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
+ synaptics@70 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x70>;
+
+ interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&pm8941_l22>;
+ vio-supply = <&pm8941_lvs3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_pin>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
};
- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <6>;
- bias-disable;
+ rmi4-f12@12 {
+ reg = <0x12>;
+ syna,sensor-type = <1>;
+ };
+ };
+};
+
+&blsp_i2c3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ clock-frequency = <100000>;
+ qcom,src-freq = <50000000>;
+
+ avago_apds993@39 {
+ compatible = "avago,apds9930";
+ reg = <0x39>;
+ interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&pm8941_l17>;
+ vddio-supply = <&pm8941_lvs1>;
+ led-max-microamp = <100000>;
+ amstaos,proximity-diodes = <0>;
+ };
+};
+
+&blsp_i2c11 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c11_pins>;
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ led-controller@38 {
+ compatible = "ti,lm3630a";
+ status = "okay";
+ reg = <0x38>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ led-sources = <0 1>;
+ label = "lcd-backlight";
+ default-brightness = <200>;
+ };
+ };
+};
+
+&blsp_i2c12 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c12_pins>;
+ clock-frequency = <100000>;
+ qcom,src-freq = <50000000>;
+
+ mpu6515@68 {
+ compatible = "invensense,mpu6515";
+ reg = <0x68>;
+ interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>;
+ vddio-supply = <&pm8941_lvs1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mpu6515_pin>;
+
+ mount-matrix = "0", "-1", "0",
+ "-1", "0", "0",
+ "0", "0", "1";
+
+ i2c-gate {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ak8963@f {
+ compatible = "asahi-kasei,ak8963";
+ reg = <0x0f>;
+ gpios = <&msmgpio 67 0>;
+ vid-supply = <&pm8941_lvs1>;
+ vdd-supply = <&pm8941_l17>;
};
- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
+ bmp280@76 {
+ compatible = "bosch,bmp280";
+ reg = <0x76>;
+ vdda-supply = <&pm8941_lvs1>;
+ vddd-supply = <&pm8941_l17>;
};
};
+ };
+};
- i2c1_pins: i2c1 {
- mux {
- pins = "gpio2", "gpio3";
- function = "blsp_i2c1";
+&msmgpio {
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
- drive-strength = <2>;
- bias-disable;
- };
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
};
+ };
- i2c2_pins: i2c2 {
- mux {
- pins = "gpio6", "gpio7";
- function = "blsp_i2c2";
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <6>;
+ bias-disable;
+ };
- drive-strength = <2>;
- bias-disable;
- };
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
};
+ };
- i2c3_pins: i2c3 {
- mux {
- pins = "gpio10", "gpio11";
- function = "blsp_i2c3";
- drive-strength = <2>;
- bias-disable;
- };
+ i2c1_pins: i2c1 {
+ mux {
+ pins = "gpio2", "gpio3";
+ function = "blsp_i2c1";
+
+ drive-strength = <2>;
+ bias-disable;
};
+ };
- i2c11_pins: i2c11 {
- mux {
- pins = "gpio83", "gpio84";
- function = "blsp_i2c11";
+ i2c2_pins: i2c2 {
+ mux {
+ pins = "gpio6", "gpio7";
+ function = "blsp_i2c2";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
};
+ };
- i2c12_pins: i2c12 {
- mux {
- pins = "gpio87", "gpio88";
- function = "blsp_i2c12";
- drive-strength = <2>;
- bias-disable;
- };
+ i2c3_pins: i2c3 {
+ mux {
+ pins = "gpio10", "gpio11";
+ function = "blsp_i2c3";
+ drive-strength = <2>;
+ bias-disable;
};
+ };
- mpu6515_pin: mpu6515 {
- irq {
- pins = "gpio73";
- function = "gpio";
- bias-disable;
- input-enable;
- };
+ i2c11_pins: i2c11 {
+ mux {
+ pins = "gpio83", "gpio84";
+ function = "blsp_i2c11";
+
+ drive-strength = <2>;
+ bias-disable;
};
+ };
- touch_pin: touch {
- int {
- pins = "gpio5";
- function = "gpio";
+ i2c12_pins: i2c12 {
+ mux {
+ pins = "gpio87", "gpio88";
+ function = "blsp_i2c12";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
- drive-strength = <2>;
- bias-disable;
- input-enable;
- };
+ mpu6515_pin: mpu6515 {
+ irq {
+ pins = "gpio73";
+ function = "gpio";
+ bias-disable;
+ input-enable;
+ };
+ };
- reset {
- pins = "gpio8";
- function = "gpio";
+ touch_pin: touch {
+ int {
+ pins = "gpio5";
+ function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
};
- panel_pin: panel {
- te {
- pins = "gpio12";
- function = "mdp_vsync";
+ reset {
+ pins = "gpio8";
+ function = "gpio";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-pull-up;
};
+ };
- bt_pin: bt {
- hostwake {
- pins = "gpio42";
- function = "gpio";
- };
+ panel_pin: panel {
+ te {
+ pins = "gpio12";
+ function = "mdp_vsync";
- devwake {
- pins = "gpio62";
- function = "gpio";
- };
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
- shutdown {
- pins = "gpio41";
- function = "gpio";
- };
+ bt_pin: bt {
+ hostwake {
+ pins = "gpio42";
+ function = "gpio";
};
- blsp2_uart10_pin_a: blsp2-uart10-pin-active {
- tx {
- pins = "gpio53";
- function = "blsp_uart10";
+ devwake {
+ pins = "gpio62";
+ function = "gpio";
+ };
- drive-strength = <2>;
- bias-disable;
- };
+ shutdown {
+ pins = "gpio41";
+ function = "gpio";
+ };
+ };
- rx {
- pins = "gpio54";
- function = "blsp_uart10";
+ blsp2_uart10_pin_a: blsp2-uart10-pin-active {
+ tx {
+ pins = "gpio53";
+ function = "blsp_uart10";
- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <2>;
+ bias-disable;
+ };
- cts {
- pins = "gpio55";
- function = "blsp_uart10";
+ rx {
+ pins = "gpio54";
+ function = "blsp_uart10";
- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <2>;
+ bias-pull-up;
+ };
- rts {
- pins = "gpio56";
- function = "blsp_uart10";
+ cts {
+ pins = "gpio55";
+ function = "blsp_uart10";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-pull-up;
};
- };
- sdhci@f9824900 {
- status = "okay";
+ rts {
+ pins = "gpio56";
+ function = "blsp_uart10";
- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+};
- bus-width = <8>;
- non-removable;
+&mdss {
+ status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
+ mdp@fd900000 {
+ status = "okay";
};
- sdhci@f98a4900 {
+ dsi@fd922800 {
status = "okay";
- max-frequency = <100000000>;
- bus-width = <4>;
- non-removable;
- vmmc-supply = <&vreg_wlan>;
- vqmmc-supply = <&pm8941_s3>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>;
+ vdda-supply = <&pm8941_l2>;
+ vdd-supply = <&pm8941_lvs3>;
+ vddio-supply = <&pm8941_l12>;
#address-cells = <1>;
#size-cells = <0>;
- bcrmf@1 {
- compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
- reg = <1>;
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
- brcm,drive-strength = <10>;
+ panel: panel@0 {
+ reg = <0>;
+ compatible = "lg,acx467akm-7";
pinctrl-names = "default";
- pinctrl-0 = <&wlan_sleep_clk_pin>;
+ pinctrl-0 = <&panel_pin>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
};
};
- serial@f9960000 {
+ dsi-phy@fd922a00 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&blsp2_uart10_pin_a>;
+ vddio-supply = <&pm8941_l12>;
+ };
+};
- bluetooth {
- compatible = "brcm,bcm43438-bt";
- max-speed = <3000000>;
+&otg {
+ status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&bt_pin>;
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
- host-wakeup-gpios = <&msmgpio 42 GPIO_ACTIVE_HIGH>;
- device-wakeup-gpios = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
- shutdown-gpios = <&msmgpio 41 GPIO_ACTIVE_HIGH>;
- };
- };
+ extcon = <&charger>, <&usb_id>;
+ vbus-supply = <&usb_otg_vbus>;
- i2c@f9967000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c11_pins>;
- clock-frequency = <355000>;
- qcom,src-freq = <50000000>;
+ hnp-disable;
+ srp-disable;
+ adp-disable;
- led-controller@38 {
- compatible = "ti,lm3630a";
+ ulpi {
+ phy@a {
status = "okay";
- reg = <0x38>;
- #address-cells = <1>;
- #size-cells = <0>;
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
- led@0 {
- reg = <0>;
- led-sources = <0 1>;
- label = "lcd-backlight";
- default-brightness = <200>;
- };
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
};
};
+};
- i2c@f9968000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c12_pins>;
- clock-frequency = <100000>;
- qcom,src-freq = <50000000>;
+&rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };
- mpu6515@68 {
- compatible = "invensense,mpu6515";
- reg = <0x68>;
- interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>;
- vddio-supply = <&pm8941_lvs1>;
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&mpu6515_pin>;
-
- mount-matrix = "0", "-1", "0",
- "-1", "0", "0",
- "0", "0", "1";
-
- i2c-gate {
- #address-cells = <1>;
- #size-cells = <0>;
- ak8963@f {
- compatible = "asahi-kasei,ak8963";
- reg = <0x0f>;
- gpios = <&msmgpio 67 0>;
- vid-supply = <&pm8941_lvs1>;
- vdd-supply = <&pm8941_l17>;
- };
+ s3 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
- bmp280@76 {
- compatible = "bosch,bmp280";
- reg = <0x76>;
- vdda-supply = <&pm8941_lvs1>;
- vddd-supply = <&pm8941_l17>;
- };
- };
+ s4 {
+ regulator-min-microvolt = <815000>;
+ regulator-max-microvolt = <900000>;
};
};
- i2c@f9923000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- clock-frequency = <100000>;
- qcom,src-freq = <50000000>;
-
- charger: bq24192@6b {
- compatible = "ti,bq24192";
- reg = <0x6b>;
- interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
- omit-battery-class;
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
- usb_otg_vbus: usb-otg-vbus { };
+ regulator-boot-on;
};
- fuelgauge: max17048@36 {
- compatible = "maxim,max17048";
- reg = <0x36>;
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- maxim,double-soc;
- maxim,rcomp = /bits/ 8 <0x4d>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- interrupt-parent = <&msmgpio>;
- interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
- pinctrl-names = "default";
- pinctrl-0 = <&fuelgauge_pin>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- maxim,alert-low-soc-level = <2>;
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
};
- };
- i2c@f9924000 {
- status = "okay";
+ l3 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
- clock-frequency = <355000>;
- qcom,src-freq = <50000000>;
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- synaptics@70 {
- compatible = "syna,rmi4-i2c";
- reg = <0x70>;
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>;
- vdd-supply = <&pm8941_l22>;
- vio-supply = <&pm8941_lvs3>;
+ regulator-boot-on;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&touch_pin>;
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- #address-cells = <1>;
- #size-cells = <0>;
+ regulator-boot-on;
+ };
- rmi4-f01@1 {
- reg = <0x1>;
- syna,nosleep-mode = <1>;
- };
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- rmi4-f12@12 {
- reg = <0x12>;
- syna,sensor-type = <1>;
- };
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
};
- };
- i2c@f9925000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins>;
- clock-frequency = <100000>;
- qcom,src-freq = <50000000>;
+ l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
- avago_apds993@39 {
- compatible = "avago,apds9930";
- reg = <0x39>;
- interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
- vdd-supply = <&pm8941_l17>;
- vddio-supply = <&pm8941_lvs1>;
- led-max-microamp = <100000>;
- amstaos,proximity-diodes = <0>;
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
};
- };
- usb@f9a55000 {
- status = "okay";
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- extcon = <&charger>, <&usb_id>;
- vbus-supply = <&usb_otg_vbus>;
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
- hnp-disable;
- srp-disable;
- adp-disable;
+ regulator-boot-on;
+ };
- ulpi {
- phy@a {
- status = "okay";
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- v1p8-supply = <&pm8941_l6>;
- v3p3-supply = <&pm8941_l24>;
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
};
- };
- mdss@fd900000 {
- status = "okay";
+ l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
- mdp@fd900000 {
- status = "okay";
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
};
- dsi@fd922800 {
- status = "okay";
+ l19 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };
- vdda-supply = <&pm8941_l2>;
- vdd-supply = <&pm8941_lvs3>;
- vddio-supply = <&pm8941_l12>;
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
- #address-cells = <1>;
- #size-cells = <0>;
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ regulator-allow-set-load;
+ };
- ports {
- port@1 {
- endpoint {
- remote-endpoint = <&panel_in>;
- data-lanes = <0 1 2 3>;
- };
- };
- };
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
- panel: panel@0 {
- reg = <0>;
- compatible = "lg,acx467akm-7";
+ regulator-boot-on;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&panel_pin>;
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };
- port {
- panel_in: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
- };
- };
+ l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
};
- dsi-phy@fd922a00 {
- status = "okay";
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
- vddio-supply = <&pm8941_l12>;
+ regulator-boot-on;
};
};
};
+&sdhci1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci3 {
+ status = "okay";
+
+ max-frequency = <100000000>;
+ bus-width = <4>;
+ non-removable;
+ vmmc-supply = <&vreg_wlan>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bcrmf@1 {
+ compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ brcm,drive-strength = <10>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_sleep_clk_pin>;
+ };
+};
+
&spmi_bus {
pm8941@0 {
gpios@c000 {
diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
index 6e036a440532..ffa31625de17 100644
--- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
@@ -12,8 +12,8 @@ / {
aliases {
serial0 = &blsp1_uart1;
- mmc0 = &sdhc_1; /* SDC1 eMMC slot */
- mmc1 = &sdhc_2; /* SDC2 SD card slot */
+ mmc0 = &sdhci1; /* SDC1 eMMC slot */
+ mmc1 = &sdhci2; /* SDC2 SD card slot */
};
chosen {
@@ -52,197 +52,6 @@ volume-up {
};
};
- smd {
- rpm {
- rpm_requests {
- pma8084-regulators {
- compatible = "qcom,rpm-pma8084-regulators";
- status = "okay";
-
- pma8084_s1: s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- regulator-always-on;
- };
-
- pma8084_s2: s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- pma8084_s3: s3 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- };
-
- pma8084_s4: s4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_s5: s5 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- };
-
- pma8084_s6: s6 {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- };
-
- pma8084_l1: l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- pma8084_l2: l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- pma8084_l3: l3 {
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1200000>;
- };
-
- pma8084_l4: l4 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1225000>;
- };
-
- pma8084_l5: l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l6: l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l7: l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l8: l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l9: l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- pma8084_l10: l10 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- pma8084_l11: l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- };
-
- pma8084_l12: l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- pma8084_l13: l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- pma8084_l14: l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- pma8084_l15: l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- pma8084_l16: l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- pma8084_l17: l17 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- pma8084_l18: l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- pma8084_l19: l19 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- pma8084_l20: l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- pma8084_l21: l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
-
- pma8084_l22: l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3300000>;
- };
-
- pma8084_l23: l23 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- pma8084_l24: l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
-
- pma8084_l25: l25 {
- regulator-min-microvolt = <2100000>;
- regulator-max-microvolt = <2100000>;
- };
-
- pma8084_l26: l26 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2050000>;
- };
-
- pma8084_l27: l27 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1225000>;
- };
-
- pma8084_lvs1: lvs1 {};
- pma8084_lvs2: lvs2 {};
- pma8084_lvs3: lvs3 {};
- pma8084_lvs4: lvs4 {};
-
- pma8084_5vs1: 5vs1 {};
- };
- };
- };
- };
-
i2c-gpio-touchkey {
compatible = "i2c-gpio";
#address-cells = <1>;
@@ -353,493 +162,677 @@ adsp-pil {
};
};
-&soc {
- serial@f991e000 {
- status = "okay";
- };
+&blsp_i2c2 {
+ status = "okay";
- /* blsp2_uart8 */
- serial@f995e000 {
- status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&blsp2_uart8_pins_active>;
- pinctrl-1 = <&blsp2_uart8_pins_sleep>;
+ touchscreen@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
- bluetooth {
- compatible = "brcm,bcm43540-bt";
- max-speed = <3000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&bt_pins>;
- device-wakeup-gpios = <&msmgpio 91 GPIO_ACTIVE_HIGH>;
- shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
- interrupt-parent = <&msmgpio>;
- interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "host-wakeup";
- };
- };
+ interrupt-parent = <&pma8084_gpios>;
+ interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
- pinctrl@fd510000 {
- blsp2_uart8_pins_active: blsp2-uart8-pins-active {
- pins = "gpio45", "gpio46", "gpio47", "gpio48";
- function = "blsp_uart8";
- drive-strength = <8>;
- bias-disable;
+ vdd-supply = <&max77826_ldo13>;
+ vio-supply = <&pma8084_lvs2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_pin>;
+
+ syna,startup-delay-ms = <100>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
};
- blsp2_uart8_pins_sleep: blsp2-uart8-pins-sleep {
- pins = "gpio45", "gpio46", "gpio47", "gpio48";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
+ rmi4-f12@12 {
+ reg = <0x12>;
+ syna,sensor-type = <1>;
};
+ };
+};
- bt_pins: bt-pins {
- hostwake {
- pins = "gpio75";
- function = "gpio";
- drive-strength = <16>;
- input-enable;
+&blsp_i2c6 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_pins>;
+
+ pmic@60 {
+ reg = <0x60>;
+ compatible = "maxim,max77826";
+
+ regulators {
+ max77826_ldo1: LDO1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
};
- devwake {
- pins = "gpio91";
- function = "gpio";
- drive-strength = <2>;
+ max77826_ldo2: LDO2 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
};
- };
- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <4>;
- bias-disable;
+ max77826_ldo3: LDO3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
};
- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <4>;
- bias-pull-up;
+ max77826_ldo4: LDO4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
- };
- sdhc2_pin_a: sdhc2-pin-active {
- clk-cmd-data {
- pins = "gpio35", "gpio36", "gpio37", "gpio38",
- "gpio39", "gpio40";
- function = "sdc3";
- drive-strength = <8>;
- bias-disable;
+ max77826_ldo5: LDO5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
- };
- sdhc2_cd_pin: sdhc2-cd {
- pins = "gpio62";
- function = "gpio";
+ max77826_ldo6: LDO6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
- drive-strength = <2>;
- bias-disable;
- };
+ max77826_ldo7: LDO7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- sdhc3_pin_a: sdhc3-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <6>;
- bias-disable;
+ max77826_ldo8: LDO8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
};
- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
+ max77826_ldo9: LDO9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
- };
- i2c2_pins: i2c2 {
- mux {
- pins = "gpio6", "gpio7";
- function = "blsp_i2c2";
+ max77826_ldo10: LDO10 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2950000>;
+ };
- drive-strength = <2>;
- bias-disable;
+ max77826_ldo11: LDO11 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2950000>;
};
- };
- i2c6_pins: i2c6 {
- mux {
- pins = "gpio29", "gpio30";
- function = "blsp_i2c6";
+ max77826_ldo12: LDO12 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ };
- drive-strength = <2>;
- bias-disable;
+ max77826_ldo13: LDO13 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
};
- };
- i2c12_pins: i2c12 {
- mux {
- pins = "gpio87", "gpio88";
- function = "blsp_i2c12";
+ max77826_ldo14: LDO14 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
- drive-strength = <2>;
- bias-disable;
+ max77826_ldo15: LDO15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
- };
- i2c_touchkey_pins: i2c-touchkey {
- mux {
- pins = "gpio95", "gpio96";
- function = "gpio";
- input-enable;
- bias-pull-up;
+ max77826_buck: BUCK {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
};
- };
- i2c_led_gpioex_pins: i2c-led-gpioex {
- mux {
- pins = "gpio120", "gpio121";
- function = "gpio";
- input-enable;
- bias-pull-down;
+ max77826_buckboost: BUCKBOOST {
+ regulator-min-microvolt = <3400000>;
+ regulator-max-microvolt = <3400000>;
};
};
+ };
+};
- gpioex_pin: gpioex {
- res {
- pins = "gpio145";
- function = "gpio";
+&blsp_i2c12 {
+ status = "okay";
- bias-pull-up;
- drive-strength = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c12_pins>;
+
+ fuelgauge@36 {
+ compatible = "maxim,max17048";
+ reg = <0x36>;
+
+ maxim,double-soc;
+ maxim,rcomp = /bits/ 8 <0x56>;
+
+ interrupt-parent = <&pma8084_gpios>;
+ interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&fuelgauge_pin>;
+ };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&blsp2_uart8 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp2_uart8_pins_active>;
+ pinctrl-1 = <&blsp2_uart8_pins_sleep>;
+
+ bluetooth {
+ compatible = "brcm,bcm43540-bt";
+ max-speed = <3000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_pins>;
+ device-wakeup-gpios = <&msmgpio 91 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
+ interrupt-parent = <&msmgpio>;
+ interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wakeup";
+ };
+};
+
+&gpu {
+ status = "ok";
+};
+
+&mdss {
+ status = "ok";
+
+ mdp@fd900000 {
+ status = "ok";
+ };
+
+ dsi@fd922800 {
+ status = "ok";
+
+ vdda-supply = <&pma8084_l2>;
+ vdd-supply = <&pma8084_l22>;
+ vddio-supply = <&pma8084_l12>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+ };
};
};
- wifi_pin: wifi {
- int {
- pins = "gpio92";
- function = "gpio";
+ panel: panel@0 {
+ reg = <0>;
+ compatible = "samsung,s6e3fa2";
- input-enable;
- bias-pull-down;
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
+
+ iovdd-supply = <&pma8084_lvs4>;
+ vddr-supply = <&vreg_panel>;
+
+ reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
+ te-gpios = <&msmgpio 12 GPIO_ACTIVE_HIGH>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
};
};
+ };
- panel_te_pin: panel {
- te {
- pins = "gpio12";
- function = "mdp_vsync";
+ dsi-phy@fd922a00 {
+ status = "ok";
- drive-strength = <2>;
- bias-disable;
- };
+ vddio-supply = <&pma8084_l12>;
+ };
+};
+
+&msmgpio {
+ blsp2_uart8_pins_active: blsp2-uart8-pins-active {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "blsp_uart8";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ blsp2_uart8_pins_sleep: blsp2-uart8-pins-sleep {
+ pins = "gpio45", "gpio46", "gpio47", "gpio48";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ bt_pins: bt-pins {
+ hostwake {
+ pins = "gpio75";
+ function = "gpio";
+ drive-strength = <16>;
+ input-enable;
+ };
+
+ devwake {
+ pins = "gpio91";
+ function = "gpio";
+ drive-strength = <2>;
};
};
- sdhc_1: sdhci@f9824900 {
- status = "okay";
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <4>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <4>;
+ bias-pull-up;
+ };
+ };
- vmmc-supply = <&pma8084_l20>;
- vqmmc-supply = <&pma8084_s4>;
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk-cmd-data {
+ pins = "gpio35", "gpio36", "gpio37", "gpio38",
+ "gpio39", "gpio40";
+ function = "sdc3";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
- bus-width = <8>;
- non-removable;
+ sdhc2_cd_pin: sdhc2-cd {
+ pins = "gpio62";
+ function = "gpio";
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
+ drive-strength = <2>;
+ bias-disable;
};
- sdhc_2: sdhci@f9864900 {
- status = "okay";
+ sdhc3_pin_a: sdhc3-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
- max-frequency = <100000000>;
+ i2c2_pins: i2c2 {
+ mux {
+ pins = "gpio6", "gpio7";
+ function = "blsp_i2c2";
- vmmc-supply = <&pma8084_l21>;
- vqmmc-supply = <&pma8084_l13>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
- bus-width = <4>;
+ i2c6_pins: i2c6 {
+ mux {
+ pins = "gpio29", "gpio30";
+ function = "blsp_i2c6";
- /* cd-gpio is intentionally disabled. If enabled, an SD card
- * present during boot is not initialized correctly. Without
- * cd-gpios the driver resorts to polling, so hotplug works.
- */
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a /* &sdhc2_cd_pin */>;
- // cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ drive-strength = <2>;
+ bias-disable;
+ };
};
- sdhci@f98a4900 {
- status = "okay";
+ i2c12_pins: i2c12 {
+ mux {
+ pins = "gpio87", "gpio88";
+ function = "blsp_i2c12";
- #address-cells = <1>;
- #size-cells = <0>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
- max-frequency = <100000000>;
+ i2c_touchkey_pins: i2c-touchkey {
+ mux {
+ pins = "gpio95", "gpio96";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ };
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc3_pin_a>;
+ i2c_led_gpioex_pins: i2c-led-gpioex {
+ mux {
+ pins = "gpio120", "gpio121";
+ function = "gpio";
+ input-enable;
+ bias-pull-down;
+ };
+ };
- vmmc-supply = <&vreg_wlan>;
- vqmmc-supply = <&pma8084_s4>;
+ gpioex_pin: gpioex {
+ res {
+ pins = "gpio145";
+ function = "gpio";
- bus-width = <4>;
- non-removable;
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+ };
- wifi@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
+ wifi_pin: wifi {
+ int {
+ pins = "gpio92";
+ function = "gpio";
- interrupt-parent = <&msmgpio>;
- interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "host-wake";
+ input-enable;
+ bias-pull-down;
+ };
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
+ panel_te_pin: panel {
+ te {
+ pins = "gpio12";
+ function = "mdp_vsync";
+
+ drive-strength = <2>;
+ bias-disable;
};
};
+};
- usb@f9a55000 {
- status = "okay";
+&mss_pil {
+ cx-supply = <&pma8084_s2>;
+ mss-supply = <&pma8084_s6>;
+ mx-supply = <&pma8084_s1>;
+ pll-supply = <&pma8084_l12>;
+};
- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
- /*extcon = <&smbb>, <&usb_id>;*/
- /*vbus-supply = <&chg_otg>;*/
+&otg {
+ status = "okay";
- hnp-disable;
- srp-disable;
- adp-disable;
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ /*extcon = <&smbb>, <&usb_id>;*/
+ /*vbus-supply = <&chg_otg>;*/
- ulpi {
- phy@a {
- status = "okay";
+ hnp-disable;
+ srp-disable;
+ adp-disable;
- v1p8-supply = <&pma8084_l6>;
- v3p3-supply = <&pma8084_l24>;
+ ulpi {
+ phy@a {
+ status = "okay";
- /*extcon = <&smbb>;*/
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ v1p8-supply = <&pma8084_l6>;
+ v3p3-supply = <&pma8084_l24>;
+
+ /*extcon = <&smbb>;*/
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
};
};
+};
- i2c@f9924000 {
+&rpm_requests {
+ pma8084-regulators {
+ compatible = "qcom,rpm-pma8084-regulators";
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
+ pma8084_s1: s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ };
- touchscreen@20 {
- compatible = "syna,rmi4-i2c";
- reg = <0x20>;
+ pma8084_s2: s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
- interrupt-parent = <&pma8084_gpios>;
- interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+ pma8084_s3: s3 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
- vdd-supply = <&max77826_ldo13>;
- vio-supply = <&pma8084_lvs2>;
+ pma8084_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&touch_pin>;
+ pma8084_s5: s5 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ };
- syna,startup-delay-ms = <100>;
+ pma8084_s6: s6 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
- #address-cells = <1>;
- #size-cells = <0>;
+ pma8084_l1: l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
- rmi4-f01@1 {
- reg = <0x1>;
- syna,nosleep-mode = <1>;
- };
+ pma8084_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
- rmi4-f12@12 {
- reg = <0x12>;
- syna,sensor-type = <1>;
- };
+ pma8084_l3: l3 {
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1200000>;
};
- };
- i2c@f9928000 {
- status = "okay";
+ pma8084_l4: l4 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1225000>;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&i2c6_pins>;
+ pma8084_l5: l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- pmic@60 {
- reg = <0x60>;
- compatible = "maxim,max77826";
+ pma8084_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- regulators {
- max77826_ldo1: LDO1 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
+ pma8084_l7: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- max77826_ldo2: LDO2 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
+ pma8084_l8: l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- max77826_ldo3: LDO3 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
+ pma8084_l9: l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
- max77826_ldo4: LDO4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ pma8084_l10: l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
- max77826_ldo5: LDO5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ pma8084_l11: l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
- max77826_ldo6: LDO6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
+ pma8084_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- max77826_ldo7: LDO7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ pma8084_l13: l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
- max77826_ldo8: LDO8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
+ pma8084_l14: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- max77826_ldo9: LDO9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ pma8084_l15: l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
- max77826_ldo10: LDO10 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2950000>;
- };
+ pma8084_l16: l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
- max77826_ldo11: LDO11 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2950000>;
- };
+ pma8084_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
- max77826_ldo12: LDO12 {
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <3300000>;
- };
+ pma8084_l18: l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
- max77826_ldo13: LDO13 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
+ pma8084_l19: l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
- max77826_ldo14: LDO14 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
+ pma8084_l20: l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
- max77826_ldo15: LDO15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ regulator-allow-set-load;
+ regulator-system-load = <200000>;
+ };
- max77826_buck: BUCK {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
+ pma8084_l21: l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
- max77826_buckboost: BUCKBOOST {
- regulator-min-microvolt = <3400000>;
- regulator-max-microvolt = <3400000>;
- };
- };
+ regulator-allow-set-load;
+ regulator-system-load = <200000>;
};
- };
- i2c@f9968000 {
- status = "okay";
+ pma8084_l22: l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&i2c12_pins>;
+ pma8084_l23: l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
- fuelgauge@36 {
- compatible = "maxim,max17048";
- reg = <0x36>;
+ pma8084_l24: l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
- maxim,double-soc;
- maxim,rcomp = /bits/ 8 <0x56>;
+ pma8084_l25: l25 {
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ };
- interrupt-parent = <&pma8084_gpios>;
- interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+ pma8084_l26: l26 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2050000>;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&fuelgauge_pin>;
+ pma8084_l27: l27 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1225000>;
};
- };
- adreno@fdb00000 {
- status = "ok";
+ pma8084_lvs1: lvs1 {};
+ pma8084_lvs2: lvs2 {};
+ pma8084_lvs3: lvs3 {};
+ pma8084_lvs4: lvs4 {};
+
+ pma8084_5vs1: 5vs1 {};
};
+};
- mdss@fd900000 {
- status = "ok";
+&sdhci1 {
+ status = "okay";
- mdp@fd900000 {
- status = "ok";
- };
+ vmmc-supply = <&pma8084_l20>;
+ vqmmc-supply = <&pma8084_s4>;
+
+ bus-width = <8>;
+ non-removable;
- dsi@fd922800 {
- status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
- vdda-supply = <&pma8084_l2>;
- vdd-supply = <&pma8084_l22>;
- vddio-supply = <&pma8084_l12>;
+&sdhci2 {
+ status = "okay";
- #address-cells = <1>;
- #size-cells = <0>;
+ max-frequency = <100000000>;
- ports {
- port@1 {
- endpoint {
- remote-endpoint = <&panel_in>;
- data-lanes = <0 1 2 3>;
- };
- };
- };
+ vmmc-supply = <&pma8084_l21>;
+ vqmmc-supply = <&pma8084_l13>;
- panel: panel@0 {
- reg = <0>;
- compatible = "samsung,s6e3fa2";
+ bus-width = <4>;
- pinctrl-names = "default";
- pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
+ /* cd-gpio is intentionally disabled. If enabled, an SD card
+ * present during boot is not initialized correctly. Without
+ * cd-gpios the driver resorts to polling, so hotplug works.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a /* &sdhc2_cd_pin */>;
+ // cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+};
- iovdd-supply = <&pma8084_lvs4>;
- vddr-supply = <&vreg_panel>;
+&sdhci3 {
+ status = "okay";
- reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
- te-gpios = <&msmgpio 12 GPIO_ACTIVE_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
- port {
- panel_in: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
- };
- };
- };
+ max-frequency = <100000000>;
- dsi-phy@fd922a00 {
- status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc3_pin_a>;
- vddio-supply = <&pma8084_l12>;
- };
- };
+ vmmc-supply = <&vreg_wlan>;
+ vqmmc-supply = <&pma8084_s4>;
- remoteproc@fc880000 {
- cx-supply = <&pma8084_s2>;
- mss-supply = <&pma8084_s6>;
- mx-supply = <&pma8084_s1>;
- pll-supply = <&pma8084_l12>;
+ bus-width = <4>;
+ non-removable;
+
+ wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wake";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
};
};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
index 79e2cfbbb1ba..4f28ca3340de 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
@@ -57,339 +57,332 @@ memory@0 {
reg = <0 0x40000000>, <0x40000000 0x40000000>;
device_type = "memory";
};
+};
- smd {
- rpm {
- rpm_requests {
- pm8841-regulators {
- s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s3 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s4 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
- };
-
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
- vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
- vdd_l21-supply = <&vreg_boost>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s4 {
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1350000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-boot-on;
- regulator-system-load = <200000>;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l23 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
+&blsp1_uart2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart2_pin_a>;
+};
+
+&blsp2_dma {
+ qcom,controlled-remotely;
+};
+
+&msmgpio {
+ blsp1_uart2_pin_a: blsp1-uart2-pin-active {
+ rx {
+ pins = "gpio5";
+ function = "blsp_uart2";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ tx {
+ pins = "gpio4";
+ function = "blsp_uart2";
+
+ drive-strength = <4>;
+ bias-disable;
};
};
-};
-&soc {
- sdhci@f9824900 {
- status = "okay";
+ i2c2_pins: i2c2 {
+ mux {
+ pins = "gpio6", "gpio7";
+ function = "blsp_i2c2";
- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
- bus-width = <8>;
- non-removable;
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
};
- sdhci@f98a4900 {
- status = "okay";
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";
- bus-width = <4>;
+ drive-strength = <2>;
+ bias-disable;
+ };
- vmmc-supply = <&pm8941_l21>;
- vqmmc-supply = <&pm8941_l13>;
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <10>;
+ bias-disable;
+ };
- cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+};
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+&otg {
+ status = "okay";
+
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ ulpi {
+ phy@a {
+ status = "okay";
+
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
+
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+ };
};
+};
+
+&rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };
- serial@f991e000 {
- status = "okay";
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&blsp1_uart2_pin_a>;
+ s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
};
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- pinctrl@fd510000 {
- blsp1_uart2_pin_a: blsp1-uart2-pin-active {
- rx {
- pins = "gpio5";
- function = "blsp_uart2";
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };
- drive-strength = <2>;
- bias-pull-up;
- };
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- tx {
- pins = "gpio4";
- function = "blsp_uart2";
+ s4 {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
- drive-strength = <4>;
- bias-disable;
- };
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ regulator-always-on;
+ regulator-boot-on;
};
- i2c2_pins: i2c2 {
- mux {
- pins = "gpio6", "gpio7";
- function = "blsp_i2c2";
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
- drive-strength = <2>;
- bias-disable;
- };
+ l3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
};
- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
- sdhc2_cd_pin_a: sdhc2-cd-pin-active {
- pins = "gpio62";
- function = "gpio";
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- drive-strength = <2>;
- bias-disable;
- };
+ regulator-boot-on;
+ };
- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <10>;
- bias-disable;
- };
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
- };
+ regulator-boot-on;
};
- };
- dma-controller@f9944000 {
- qcom,controlled-remotely;
- };
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- usb@f9a55000 {
- status = "okay";
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
- extcon = <&smbb>, <&usb_id>;
- vbus-supply = <&chg_otg>;
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };
- hnp-disable;
- srp-disable;
- adp-disable;
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- ulpi {
- phy@a {
- status = "okay";
+ regulator-always-on;
+ regulator-boot-on;
+ };
- v1p8-supply = <&pm8941_l6>;
- v3p3-supply = <&pm8941_l24>;
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
- extcon = <&smbb>;
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ regulator-boot-on;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
};
};
};
+&sdhci1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci3 {
+ status = "okay";
+
+ bus-width = <4>;
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+
+ cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+};
+
&spmi_bus {
pm8941@0 {
charger@1000 {
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
index e66937e3f7dd..f4b537294fb4 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
@@ -53,186 +53,6 @@ volume-up {
};
};
- smd {
- rpm {
- rpm_requests {
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
- vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
- vdd_l21-supply = <&vreg_boost>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
-
- regulator-system-load = <154000>;
- };
-
- s4 {
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1350000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-boot-on;
- regulator-allow-set-load;
- regulator-system-load = <500000>;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l23 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
- };
- };
-
vreg_bl_vddio: lcd-backlight-vddio {
compatible = "regulator-fixed";
regulator-name = "vreg_bl_vddio";
@@ -277,385 +97,559 @@ vreg_wlan: wlan-regulator {
};
};
-&soc {
- sdhci@f9824900 {
- status = "okay";
+&blsp_i2c8 {
+ status = "okay";
- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
- bus-width = <8>;
- non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c8_pins>;
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
- };
+ synaptics@2c {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x2c>;
- sdhci@f9864900 {
- status = "okay";
+ interrupt-parent = <&msmgpio>;
+ interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
- max-frequency = <100000000>;
- non-removable;
- vmmc-supply = <&vreg_wlan>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdd-supply = <&pm8941_l22>;
+ vio-supply = <&pm8941_lvs3>;
pinctrl-names = "default";
- pinctrl-0 = <&sdhc3_pin_a>;
+ pinctrl-0 = <&ts_int_pin>;
- #address-cells = <1>;
- #size-cells = <0>;
+ syna,startup-delay-ms = <10>;
- bcrmf@1 {
- compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
- reg = <1>;
+ rmi-f01@1 {
+ reg = <0x1>;
+ syna,nosleep = <1>;
+ };
- brcm,drive-strength = <10>;
+ rmi-f11@11 {
+ reg = <0x11>;
+ syna,f11-flip-x = <1>;
+ syna,sensor-type = <1>;
+ };
+ };
+};
- pinctrl-names = "default";
- pinctrl-0 = <&wlan_sleep_clk_pin>;
+&blsp_i2c11 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c11_pins>;
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ lp8566_wled: backlight@2c {
+ compatible = "ti,lp8556";
+ reg = <0x2c>;
+ power-supply = <&vreg_bl_vddio>;
+
+ bl-name = "backlight";
+ dev-ctrl = /bits/ 8 <0x05>;
+ init-brt = /bits/ 8 <0x3f>;
+ rom_a0h {
+ rom-addr = /bits/ 8 <0xa0>;
+ rom-val = /bits/ 8 <0xff>;
+ };
+ rom_a1h {
+ rom-addr = /bits/ 8 <0xa1>;
+ rom-val = /bits/ 8 <0x3f>;
+ };
+ rom_a2h {
+ rom-addr = /bits/ 8 <0xa2>;
+ rom-val = /bits/ 8 <0x20>;
+ };
+ rom_a3h {
+ rom-addr = /bits/ 8 <0xa3>;
+ rom-val = /bits/ 8 <0x5e>;
+ };
+ rom_a4h {
+ rom-addr = /bits/ 8 <0xa4>;
+ rom-val = /bits/ 8 <0x02>;
+ };
+ rom_a5h {
+ rom-addr = /bits/ 8 <0xa5>;
+ rom-val = /bits/ 8 <0x04>;
+ };
+ rom_a6h {
+ rom-addr = /bits/ 8 <0xa6>;
+ rom-val = /bits/ 8 <0x80>;
+ };
+ rom_a7h {
+ rom-addr = /bits/ 8 <0xa7>;
+ rom-val = /bits/ 8 <0xf7>;
+ };
+ rom_a9h {
+ rom-addr = /bits/ 8 <0xa9>;
+ rom-val = /bits/ 8 <0x80>;
+ };
+ rom_aah {
+ rom-addr = /bits/ 8 <0xaa>;
+ rom-val = /bits/ 8 <0x0f>;
+ };
+ rom_aeh {
+ rom-addr = /bits/ 8 <0xae>;
+ rom-val = /bits/ 8 <0x0f>;
};
};
+};
+
+&blsp1_uart2 {
+ status = "okay";
- sdhci@f98a4900 {
- status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart2_pin_a>;
+};
- bus-width = <4>;
+&blsp2_uart7 {
+ status = "ok";
- vmmc-supply = <&pm8941_l21>;
- vqmmc-supply = <&pm8941_l13>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp2_uart7_pin_a>;
- cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <3000000>;
pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+ pinctrl-0 = <&bt_host_wake_pin>,
+ <&bt_dev_wake_pin>,
+ <&bt_reg_on_pin>;
+
+ host-wakeup-gpios = <&msmgpio 95 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&msmgpio 96 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&pm8941_gpios 16 GPIO_ACTIVE_HIGH>;
};
+};
- serial@f991e000 {
- status = "okay";
+&msmgpio {
+ blsp1_uart2_pin_a: blsp1-uart2-pin-active {
+ rx {
+ pins = "gpio5";
+ function = "blsp_uart2";
- pinctrl-names = "default";
- pinctrl-0 = <&blsp1_uart2_pin_a>;
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ tx {
+ pins = "gpio4";
+ function = "blsp_uart2";
+
+ drive-strength = <4>;
+ bias-disable;
+ };
};
- serial@f995d000 {
- status = "ok";
+ blsp2_uart7_pin_a: blsp2-uart7-pin-active {
+ tx {
+ pins = "gpio41";
+ function = "blsp_uart7";
- pinctrl-names = "default";
- pinctrl-0 = <&blsp2_uart7_pin_a>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx {
+ pins = "gpio42";
+ function = "blsp_uart7";
- bluetooth {
- compatible = "brcm,bcm43438-bt";
- max-speed = <3000000>;
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ cts {
+ pins = "gpio43";
+ function = "blsp_uart7";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&bt_host_wake_pin>,
- <&bt_dev_wake_pin>,
- <&bt_reg_on_pin>;
+ rts {
+ pins = "gpio44";
+ function = "blsp_uart7";
- host-wakeup-gpios = <&msmgpio 95 GPIO_ACTIVE_HIGH>;
- device-wakeup-gpios = <&msmgpio 96 GPIO_ACTIVE_HIGH>;
- shutdown-gpios = <&pm8941_gpios 16 GPIO_ACTIVE_HIGH>;
+ drive-strength = <2>;
+ bias-disable;
};
};
- usb@f9a55000 {
- status = "okay";
+ i2c8_pins: i2c8 {
+ mux {
+ pins = "gpio47", "gpio48";
+ function = "blsp_i2c8";
- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
- extcon = <&smbb>, <&usb_id>;
- vbus-supply = <&chg_otg>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
- hnp-disable;
- srp-disable;
- adp-disable;
+ i2c11_pins: i2c11 {
+ mux {
+ pins = "gpio83", "gpio84";
+ function = "blsp_i2c11";
- ulpi {
- phy@a {
- status = "okay";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
- v1p8-supply = <&pm8941_l6>;
- v3p3-supply = <&pm8941_l24>;
+ lcd_backlight_en_pin_a: lcd-backlight-vddio {
+ pins = "gpio69";
+ drive-strength = <10>;
+ output-low;
+ bias-disable;
+ };
- extcon = <&smbb>;
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
};
};
- pinctrl@fd510000 {
- blsp1_uart2_pin_a: blsp1-uart2-pin-active {
- rx {
- pins = "gpio5";
- function = "blsp_uart2";
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <2>;
+ bias-disable;
+ };
- tx {
- pins = "gpio4";
- function = "blsp_uart2";
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <6>;
+ bias-disable;
+ };
- drive-strength = <4>;
- bias-disable;
- };
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
};
+ };
- blsp2_uart7_pin_a: blsp2-uart7-pin-active {
- tx {
- pins = "gpio41";
- function = "blsp_uart7";
+ sdhc3_pin_a: sdhc3-pin-active {
+ clk {
+ pins = "gpio40";
+ function = "sdc3";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <10>;
+ bias-disable;
+ };
- rx {
- pins = "gpio42";
- function = "blsp_uart7";
+ cmd {
+ pins = "gpio39";
+ function = "sdc3";
- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <10>;
+ bias-pull-up;
+ };
- cts {
- pins = "gpio43";
- function = "blsp_uart7";
+ data {
+ pins = "gpio35", "gpio36", "gpio37", "gpio38";
+ function = "sdc3";
- drive-strength = <2>;
- bias-pull-up;
- };
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
- rts {
- pins = "gpio44";
- function = "blsp_uart7";
+ ts_int_pin: synaptics {
+ pin {
+ pins = "gpio86";
+ function = "gpio";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
};
+ };
- i2c8_pins: i2c8 {
- mux {
- pins = "gpio47", "gpio48";
- function = "blsp_i2c8";
+ bt_host_wake_pin: bt-host-wake {
+ pins = "gpio95";
+ function = "gpio";
- drive-strength = <2>;
- bias-disable;
- };
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ bt_dev_wake_pin: bt-dev-wake {
+ pins = "gpio96";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&otg {
+ status = "okay";
+
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ ulpi {
+ phy@a {
+ status = "okay";
+
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
+
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+ };
+ };
+};
+
+&rpm_requests {
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
};
- i2c11_pins: i2c11 {
- mux {
- pins = "gpio83", "gpio84";
- function = "blsp_i2c11";
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };
- drive-strength = <2>;
- bias-disable;
- };
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-system-load = <154000>;
};
- lcd_backlight_en_pin_a: lcd-backlight-vddio {
- pins = "gpio69";
- drive-strength = <10>;
- output-low;
- bias-disable;
+ s4 {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
};
- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
+ regulator-always-on;
+ regulator-boot-on;
};
- sdhc2_cd_pin_a: sdhc2-cd-pin-active {
- pins = "gpio62";
- function = "gpio";
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
- drive-strength = <2>;
- bias-disable;
- };
+ l3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <6>;
- bias-disable;
- };
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
- };
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
- sdhc3_pin_a: sdhc3-pin-active {
- clk {
- pins = "gpio40";
- function = "sdc3";
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- drive-strength = <10>;
- bias-disable;
- };
+ regulator-boot-on;
+ };
- cmd {
- pins = "gpio39";
- function = "sdc3";
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- drive-strength = <10>;
- bias-pull-up;
- };
+ regulator-boot-on;
+ };
- data {
- pins = "gpio35", "gpio36", "gpio37", "gpio38";
- function = "sdc3";
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- drive-strength = <10>;
- bias-pull-up;
- };
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
};
- ts_int_pin: synaptics {
- pin {
- pins = "gpio86";
- function = "gpio";
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };
- drive-strength = <2>;
- bias-disable;
- input-enable;
- };
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
};
- bt_host_wake_pin: bt-host-wake {
- pins = "gpio95";
- function = "gpio";
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
- drive-strength = <2>;
- bias-disable;
- output-low;
+ regulator-boot-on;
};
- bt_dev_wake_pin: bt-dev-wake {
- pins = "gpio96";
- function = "gpio";
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- drive-strength = <2>;
- bias-disable;
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
};
- };
- i2c@f9964000 {
- status = "okay";
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
- clock-frequency = <355000>;
- qcom,src-freq = <50000000>;
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&i2c8_pins>;
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
- synaptics@2c {
- compatible = "syna,rmi4-i2c";
- reg = <0x2c>;
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
- interrupt-parent = <&msmgpio>;
- interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-allow-set-load;
+ regulator-system-load = <500000>;
+ };
- #address-cells = <1>;
- #size-cells = <0>;
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
- vdd-supply = <&pm8941_l22>;
- vio-supply = <&pm8941_lvs3>;
+ regulator-boot-on;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&ts_int_pin>;
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
- syna,startup-delay-ms = <10>;
+ l23 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
- rmi-f01@1 {
- reg = <0x1>;
- syna,nosleep = <1>;
- };
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
- rmi-f11@11 {
- reg = <0x11>;
- syna,f11-flip-x = <1>;
- syna,sensor-type = <1>;
- };
+ regulator-boot-on;
};
};
+};
+
+&sdhci1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci2 {
+ status = "okay";
+
+ max-frequency = <100000000>;
+ non-removable;
+ vmmc-supply = <&vreg_wlan>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc3_pin_a>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bcrmf@1 {
+ compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ brcm,drive-strength = <10>;
- i2c@f9967000 {
- status = "okay";
pinctrl-names = "default";
- pinctrl-0 = <&i2c11_pins>;
- clock-frequency = <355000>;
- qcom,src-freq = <50000000>;
-
- lp8566_wled: backlight@2c {
- compatible = "ti,lp8556";
- reg = <0x2c>;
- power-supply = <&vreg_bl_vddio>;
-
- bl-name = "backlight";
- dev-ctrl = /bits/ 8 <0x05>;
- init-brt = /bits/ 8 <0x3f>;
- rom_a0h {
- rom-addr = /bits/ 8 <0xa0>;
- rom-val = /bits/ 8 <0xff>;
- };
- rom_a1h {
- rom-addr = /bits/ 8 <0xa1>;
- rom-val = /bits/ 8 <0x3f>;
- };
- rom_a2h {
- rom-addr = /bits/ 8 <0xa2>;
- rom-val = /bits/ 8 <0x20>;
- };
- rom_a3h {
- rom-addr = /bits/ 8 <0xa3>;
- rom-val = /bits/ 8 <0x5e>;
- };
- rom_a4h {
- rom-addr = /bits/ 8 <0xa4>;
- rom-val = /bits/ 8 <0x02>;
- };
- rom_a5h {
- rom-addr = /bits/ 8 <0xa5>;
- rom-val = /bits/ 8 <0x04>;
- };
- rom_a6h {
- rom-addr = /bits/ 8 <0xa6>;
- rom-val = /bits/ 8 <0x80>;
- };
- rom_a7h {
- rom-addr = /bits/ 8 <0xa7>;
- rom-val = /bits/ 8 <0xf7>;
- };
- rom_a9h {
- rom-addr = /bits/ 8 <0xa9>;
- rom-val = /bits/ 8 <0x80>;
- };
- rom_aah {
- rom-addr = /bits/ 8 <0xaa>;
- rom-val = /bits/ 8 <0x0f>;
- };
- rom_aeh {
- rom-addr = /bits/ 8 <0xae>;
- rom-val = /bits/ 8 <0x0f>;
- };
- };
+ pinctrl-0 = <&wlan_sleep_clk_pin>;
};
};
+&sdhci3 {
+ status = "okay";
+
+ bus-width = <4>;
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+
+ cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+};
+
&spmi_bus {
pm8941@0 {
charger@1000 {
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
index a62e5c25b23c..a98aa3e11edf 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
@@ -57,388 +57,382 @@ memory@0 {
reg = <0 0x40000000>, <0x40000000 0x40000000>;
device_type = "memory";
};
+};
- smd {
- rpm {
- rpm_requests {
- pm8841-regulators {
- s1 {
- regulator-min-microvolt = <675000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s2 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s3 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
-
- s4 {
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1050000>;
- };
- };
-
- pm8941-regulators {
- vdd_l1_l3-supply = <&pm8941_s1>;
- vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
- vdd_l4_l11-supply = <&pm8941_s1>;
- vdd_l5_l7-supply = <&pm8941_s2>;
- vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
- vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
- vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
- vdd_l21-supply = <&vreg_boost>;
-
- s1 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s2 {
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- regulator-boot-on;
- };
-
- s3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- s4 {
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- };
-
- l1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l2 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l3 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- l4 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
-
- l5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l7 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-boot-on;
- };
-
- l8 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l9 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
-
- l11 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1350000>;
- };
-
- l12 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-always-on;
- regulator-boot-on;
- };
-
- l13 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l14 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- l15 {
- regulator-min-microvolt = <2050000>;
- regulator-max-microvolt = <2050000>;
- };
-
- l16 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l17 {
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
-
- l18 {
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- };
-
- l19 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- l20 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-allow-set-load;
- regulator-boot-on;
- regulator-system-load = <200000>;
- };
-
- l21 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
-
- regulator-boot-on;
- };
-
- l22 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- l23 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- l24 {
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
-
- regulator-boot-on;
- };
- };
- };
+&blsp_i2c2 {
+ status = "okay";
+
+ clock-frequency = <355000>;
+ qcom,src-freq = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
+ synaptics@2c {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x2c>;
+
+ interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdd-supply = <&pm8941_l22>;
+ vio-supply = <&pm8941_lvs3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_int_pin>;
+
+ syna,startup-delay-ms = <10>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f11@11 {
+ reg = <0x11>;
+ touchscreen-inverted-x;
+ syna,sensor-type = <1>;
};
};
};
-&soc {
- usb@f9a55000 {
- status = "okay";
+&blsp1_uart2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart2_pin_a>;
+};
- phys = <&usb_hs1_phy>;
- phy-select = <&tcsr 0xb000 0>;
- extcon = <&smbb>, <&usb_id>;
- vbus-supply = <&chg_otg>;
+&blsp2_dma {
+ qcom,controlled-remotely;
+};
- hnp-disable;
- srp-disable;
- adp-disable;
+&msmgpio {
+ blsp1_uart2_pin_a: blsp1-uart2-pin-active {
+ rx {
+ pins = "gpio5";
+ function = "blsp_uart2";
- ulpi {
- phy@a {
- status = "okay";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
- v1p8-supply = <&pm8941_l6>;
- v3p3-supply = <&pm8941_l24>;
+ tx {
+ pins = "gpio4";
+ function = "blsp_uart2";
- extcon = <&smbb>;
- qcom,init-seq = /bits/ 8 <0x1 0x64>;
- };
+ drive-strength = <4>;
+ bias-disable;
};
};
- sdhci@f9824900 {
- status = "okay";
+ i2c2_pins: i2c2 {
+ mux {
+ pins = "gpio6", "gpio7";
+ function = "blsp_i2c2";
- vmmc-supply = <&pm8941_l20>;
- vqmmc-supply = <&pm8941_s3>;
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
- bus-width = <8>;
- non-removable;
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc1_pin_a>;
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
};
- sdhci@f98a4900 {
- status = "okay";
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";
- bus-width = <4>;
+ drive-strength = <2>;
+ bias-disable;
+ };
- vmmc-supply = <&pm8941_l21>;
- vqmmc-supply = <&pm8941_l13>;
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <10>;
+ bias-disable;
+ };
- cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+ ts_int_pin: touch-int {
+ pin {
+ pins = "gpio61";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ input-enable;
+ };
};
+};
- serial@f991e000 {
- status = "okay";
+&otg {
+ status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&blsp1_uart2_pin_a>;
+ phys = <&usb_hs1_phy>;
+ phy-select = <&tcsr 0xb000 0>;
+ extcon = <&smbb>, <&usb_id>;
+ vbus-supply = <&chg_otg>;
+
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+
+ ulpi {
+ phy@a {
+ status = "okay";
+
+ v1p8-supply = <&pm8941_l6>;
+ v3p3-supply = <&pm8941_l24>;
+
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x64>;
+ };
};
+};
- i2c@f9924000 {
- status = "okay";
+&rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };
- clock-frequency = <355000>;
- qcom,src-freq = <50000000>;
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
+ s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
- synaptics@2c {
- compatible = "syna,rmi4-i2c";
- reg = <0x2c>;
+ s4 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+ };
- interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+ vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+ vdd_l21-supply = <&vreg_boost>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- #address-cells = <1>;
- #size-cells = <0>;
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };
- vdd-supply = <&pm8941_l22>;
- vio-supply = <&pm8941_lvs3>;
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- pinctrl-names = "default";
- pinctrl-0 = <&ts_int_pin>;
+ s4 {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
- syna,startup-delay-ms = <10>;
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
- rmi4-f01@1 {
- reg = <0x1>;
- syna,nosleep-mode = <1>;
- };
+ regulator-always-on;
+ regulator-boot-on;
+ };
- rmi4-f11@11 {
- reg = <0x11>;
- touchscreen-inverted-x;
- syna,sensor-type = <1>;
- };
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
};
- };
- pinctrl@fd510000 {
- blsp1_uart2_pin_a: blsp1-uart2-pin-active {
- rx {
- pins = "gpio5";
- function = "blsp_uart2";
+ l3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
- drive-strength = <2>;
- bias-pull-up;
- };
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
- tx {
- pins = "gpio4";
- function = "blsp_uart2";
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- drive-strength = <4>;
- bias-disable;
- };
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
};
- i2c2_pins: i2c2 {
- mux {
- pins = "gpio6", "gpio7";
- function = "blsp_i2c2";
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- drive-strength = <2>;
- bias-disable;
- };
+ regulator-boot-on;
};
- sdhc1_pin_a: sdhc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strength = <16>;
- bias-disable;
- };
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- cmd-data {
- pins = "sdc1_cmd", "sdc1_data";
- drive-strength = <10>;
- bias-pull-up;
- };
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
};
- sdhc2_cd_pin_a: sdhc2-cd-pin-active {
- pins = "gpio62";
- function = "gpio";
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };
- drive-strength = <2>;
- bias-disable;
- };
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
- sdhc2_pin_a: sdhc2-pin-active {
- clk {
- pins = "sdc2_clk";
- drive-strength = <10>;
- bias-disable;
- };
+ regulator-always-on;
+ regulator-boot-on;
+ };
- cmd-data {
- pins = "sdc2_cmd", "sdc2_data";
- drive-strength = <6>;
- bias-pull-up;
- };
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
};
- ts_int_pin: touch-int {
- pin {
- pins = "gpio61";
- function = "gpio";
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- drive-strength = <2>;
- bias-disable;
- input-enable;
- };
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
};
- };
- dma-controller@f9944000 {
- qcom,controlled-remotely;
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
+ };
};
};
+&sdhci1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&sdhci3 {
+ status = "okay";
+
+ bus-width = <4>;
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
+
+ cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+};
+
&spmi_bus {
pm8941@0 {
charger@1000 {
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 412d94736c35..02b73739b6f3 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -742,7 +742,7 @@ blsp2_uart10: serial@f9960000 {
status = "disabled";
};
- sdhci@f9824900 {
+ sdhci1: sdhci@f9824900 {
compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
reg-names = "hc_mem", "core_mem";
@@ -756,7 +756,7 @@ sdhci@f9824900 {
status = "disabled";
};
- sdhci@f9864900 {
+ sdhci2: sdhci@f9864900 {
compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
reg-names = "hc_mem", "core_mem";
@@ -770,7 +770,7 @@ sdhci@f9864900 {
status = "disabled";
};
- sdhci@f98a4900 {
+ sdhci3: sdhci@f98a4900 {
compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
reg-names = "hc_mem", "core_mem";
@@ -835,7 +835,7 @@ rng@f9bff000 {
clock-names = "core";
};
- remoteproc@fc880000 {
+ mss_pil: remoteproc@fc880000 {
compatible = "qcom,msm8974-mss-pil";
reg = <0xfc880000 0x100>, <0xfc820000 0x020>;
reg-names = "qdsp6", "rmb";
@@ -959,7 +959,7 @@ msmgpio: pinctrl@fd510000 {
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
};
- i2c@f9923000 {
+ blsp_i2c1: i2c@f9923000 {
status = "disabled";
compatible = "qcom,i2c-qup-v2.1.1";
reg = <0xf9923000 0x1000>;
@@ -970,7 +970,7 @@ i2c@f9923000 {
#size-cells = <0>;
};
- i2c@f9924000 {
+ blsp_i2c2: i2c@f9924000 {
status = "disabled";
compatible = "qcom,i2c-qup-v2.1.1";
reg = <0xf9924000 0x1000>;
@@ -1594,7 +1594,7 @@ dsi_phy0: dsi-phy@fd922a00 {
};
};
- imem@fe805000 {
+ imem: imem@fe805000 {
status = "disabled";
compatible = "syscon", "simple-mfd";
reg = <0xfe805000 0x1000>;
@@ -1614,7 +1614,7 @@ rpm {
qcom,ipc = <&apcs 8 0>;
qcom,smd-edge = <15>;
- rpm_requests {
+ rpm_requests: rpm_requests {
compatible = "qcom,rpm-msm8974";
qcom,smd-channels = "rpm_requests";
--
2.32.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 07/10] ARM: dts: qcom: do not use underscore in node name
2022-04-01 20:10 [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc Krzysztof Kozlowski
` (5 preceding siblings ...)
2022-04-01 20:10 ` [PATCH 06/10] ARM: dts: qcom: msm8974: override nodes by label Krzysztof Kozlowski
@ 2022-04-01 20:10 ` Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 08/10] dt-bindings: soc: qcom,smd: convert to dtschema Krzysztof Kozlowski
` (2 subsequent siblings)
9 siblings, 0 replies; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-01 20:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
Cc: Krzysztof Kozlowski
Align RPM requests node with DT schema by using hyphen instead of
underscore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
arch/arm/boot/dts/qcom-apq8064.dtsi | 8 ++++----
arch/arm/boot/dts/qcom-apq8084.dtsi | 2 +-
arch/arm/boot/dts/qcom-msm8974.dtsi | 2 +-
3 files changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index a1c8ae516d21..33a4d3441959 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -227,7 +227,7 @@ smem {
smd {
compatible = "qcom,smd";
- modem@0 {
+ modem-edge {
interrupts = <0 37 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&l2cc 8 3>;
@@ -236,7 +236,7 @@ modem@0 {
status = "disabled";
};
- q6@1 {
+ q6-edge {
interrupts = <0 90 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&l2cc 8 15>;
@@ -245,7 +245,7 @@ q6@1 {
status = "disabled";
};
- dsps@3 {
+ dsps-edge {
interrupts = <0 138 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&sps_sic_non_secure 0x4080 0>;
@@ -254,7 +254,7 @@ dsps@3 {
status = "disabled";
};
- riva@6 {
+ riva-edge {
interrupts = <0 198 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&l2cc 8 25>;
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index 52240fc7a1a6..da50a1a0197f 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -470,7 +470,7 @@ rpm {
qcom,ipc = <&apcs 8 0>;
qcom,smd-edge = <15>;
- rpm_requests {
+ rpm-requests {
compatible = "qcom,rpm-apq8084";
qcom,smd-channels = "rpm_requests";
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 02b73739b6f3..2035be2fb8c4 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -1614,7 +1614,7 @@ rpm {
qcom,ipc = <&apcs 8 0>;
qcom,smd-edge = <15>;
- rpm_requests: rpm_requests {
+ rpm_requests: rpm-requests {
compatible = "qcom,rpm-msm8974";
qcom,smd-channels = "rpm_requests";
--
2.32.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 08/10] dt-bindings: soc: qcom,smd: convert to dtschema
2022-04-01 20:10 [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc Krzysztof Kozlowski
` (6 preceding siblings ...)
2022-04-01 20:10 ` [PATCH 07/10] ARM: dts: qcom: do not use underscore in node name Krzysztof Kozlowski
@ 2022-04-01 20:10 ` Krzysztof Kozlowski
2022-04-02 13:46 ` Rob Herring
2022-04-04 22:27 ` Rob Herring
2022-04-01 20:10 ` [PATCH 09/10] dt-bindings: clock: qcom,rpmcc: " Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 10/10] dt-bindings: clock: qcom,rpmcc: add clocks property Krzysztof Kozlowski
9 siblings, 2 replies; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-01 20:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
Cc: Krzysztof Kozlowski
Convert the Qualcomm Shared Memory Driver bindings to DT Schema.
Changes against original bindings: enforce only specific names of child
nodes, instead of any names.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../regulator/qcom,smd-rpm-regulator.yaml | 2 +-
.../bindings/remoteproc/qcom,q6v5.txt | 2 +-
.../bindings/remoteproc/qcom,wcnss-pil.txt | 2 +-
.../bindings/soc/qcom/qcom,smd-rpm.yaml | 4 +-
.../devicetree/bindings/soc/qcom/qcom,smd.txt | 98 -------------
.../bindings/soc/qcom/qcom,smd.yaml | 137 ++++++++++++++++++
6 files changed, 142 insertions(+), 103 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt
create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd.yaml
diff --git a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.yaml b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.yaml
index f052e03be402..0daad8e3e260 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.yaml
@@ -12,7 +12,7 @@ description:
resides as a subnode of the SMD. As such, the SMD-RPM regulator requires
that the SMD and RPM nodes be present.
- Please refer to Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt for
+ Please refer to Documentation/devicetree/bindings/soc/qcom/qcom,smd.yaml for
information pertaining to the SMD node.
Please refer to Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
index 8f1507052afd..b677900b3aae 100644
--- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
+++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
@@ -250,7 +250,7 @@ the memory regions used by the Hexagon firmware. Each sub-node must contain:
The Hexagon node may also have an subnode named either "smd-edge" or
"glink-edge" that describes the communication edge, channels and devices
-related to the Hexagon. See ../soc/qcom/qcom,smd.txt and
+related to the Hexagon. See ../soc/qcom/qcom,smd.yaml and
../soc/qcom/qcom,glink.txt for details on how to describe these.
= EXAMPLE
diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt
index a83080b8905c..ac423f4c3f1b 100644
--- a/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt
+++ b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.txt
@@ -111,7 +111,7 @@ and its resource dependencies. It is described by the following properties:
The wcnss node can also have an subnode named "smd-edge" that describes the SMD
edge, channels and devices related to the WCNSS.
-See ../soc/qcom/qcom,smd.txt for details on how to describe the SMD edge.
+See ../soc/qcom/qcom,smd.yaml for details on how to describe the SMD edge.
= EXAMPLE
The following example describes the resources needed to boot control the WCNSS,
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
index b32457c2fc0b..bf862a11f721 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
@@ -12,7 +12,7 @@ description: |
to vote for state of the system resources, such as clocks, regulators and bus
frequencies.
- The SMD information for the RPM edge should be filled out. See qcom,smd.txt
+ The SMD information for the RPM edge should be filled out. See qcom,smd.yaml
for the required edge properties. All SMD related properties will reside
within the RPM node itself.
@@ -82,7 +82,7 @@ examples:
qcom,ipc = <&apcs 8 0>;
qcom,smd-edge = <15>;
- rpm_requests {
+ rpm-requests {
compatible = "qcom,rpm-msm8974";
qcom,smd-channels = "rpm_requests";
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt
deleted file mode 100644
index 234ae2256501..000000000000
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt
+++ /dev/null
@@ -1,98 +0,0 @@
-Qualcomm Shared Memory Driver (SMD) binding
-
-This binding describes the Qualcomm Shared Memory Driver, a fifo based
-communication channel for sending data between the various subsystems in
-Qualcomm platforms.
-
-- compatible:
- Usage: required
- Value type: <stringlist>
- Definition: must be "qcom,smd"
-
-= EDGES
-
-Each subnode of the SMD node represents a remote subsystem or a remote
-processor of some sort - or in SMD language an "edge". The name of the edges
-are not important.
-The edge is described by the following properties:
-
-- interrupts:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: should specify the IRQ used by the remote processor to
- signal this processor about communication related updates
-
-- mboxes:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: reference to the associated doorbell in APCS, as described
- in mailbox/mailbox.txt
-
-- qcom,ipc:
- Usage: required, unless mboxes is specified
- Value type: <prop-encoded-array>
- Definition: three entries specifying the outgoing ipc bit used for
- signaling the remote processor:
- - phandle to a syscon node representing the apcs registers
- - u32 representing offset to the register within the syscon
- - u32 representing the ipc bit within the register
-
-- qcom,smd-edge:
- Usage: required
- Value type: <u32>
- Definition: the identifier of the remote processor in the smd channel
- allocation table
-
-- qcom,remote-pid:
- Usage: optional
- Value type: <u32>
- Definition: the identifier for the remote processor as known by the rest
- of the system.
-
-- label:
- Usage: optional
- Value type: <string>
- Definition: name of the edge, used for debugging and identification
- purposes. The node name will be used if this is not
- present.
-
-= SMD DEVICES
-
-In turn, subnodes of the "edges" represent devices tied to SMD channels on that
-"edge". The names of the devices are not important. The properties of these
-nodes are defined by the individual bindings for the SMD devices - but must
-contain the following property:
-
-- qcom,smd-channels:
- Usage: required
- Value type: <stringlist>
- Definition: a list of channels tied to this device, used for matching
- the device to channels
-
-= EXAMPLE
-
-The following example represents a smd node, with one edge representing the
-"rpm" subsystem. For the "rpm" subsystem we have a device tied to the
-"rpm_request" channel.
-
- apcs: syscon@f9011000 {
- compatible = "syscon";
- reg = <0xf9011000 0x1000>;
- };
-
- smd {
- compatible = "qcom,smd";
-
- rpm {
- interrupts = <0 168 1>;
- qcom,ipc = <&apcs 8 0>;
- qcom,smd-edge = <15>;
-
- rpm_requests {
- compatible = "qcom,rpm-msm8974";
- qcom,smd-channels = "rpm_requests";
-
- ...
- };
- };
- };
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.yaml
new file mode 100644
index 000000000000..e6f9ffa1c0ea
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.yaml
@@ -0,0 +1,137 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,smd.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Shared Memory Driver
+
+maintainers:
+ - Andy Gross <agross@kernel.org>
+ - Bjorn Andersson <bjorn.andersson@linaro.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description:
+ The Qualcomm Shared Memory Driver is a FIFO based communication channel for
+ sending data between the various subsystems in Qualcomm platforms.
+
+properties:
+ compatible:
+ const: qcom,smd
+
+patternProperties:
+ "^.*-edge|rpm$":
+ type: object
+ description:
+ Each subnode of the SMD node represents a remote subsystem or a remote
+ processor of some sort - or in SMD language an "edge". The name of the
+ edges are not important.
+
+ properties:
+ interrupts:
+ maxItems: 1
+
+ label:
+ $ref: /schemas/types.yaml#/definitions/string
+ description:
+ Name of the edge, used for debugging and identification purposes. The
+ node name will be used if this is not present.
+
+ mboxes:
+ maxItems: 1
+ description:
+ Reference to the mailbox representing the outgoing doorbell in APCS for
+ this client.
+
+ qcom,ipc:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ items:
+ - items:
+ - description: phandle to a syscon node representing the APCS registers
+ - description: u32 representing offset to the register within the syscon
+ - description: u32 representing the ipc bit within the register
+ description:
+ Three entries specifying the outgoing ipc bit used for signaling the
+ remote processor.
+
+ qcom,smd-edge:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The identifier of the remote processor in the smd channel allocation
+ table.
+
+ qcom,remote-pid:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The identifier for the remote processor as known by the rest of the
+ system.
+
+ # Binding for edge subnodes is not complete
+ patternProperties:
+ "^rpm-requests$":
+ type: object
+ description:
+ In turn, subnodes of the "edges" represent devices tied to SMD
+ channels on that "edge". The names of the devices are not
+ important. The properties of these nodes are defined by the
+ individual bindings for the SMD devices.
+
+ properties:
+ qcom,smd-channels:
+ $ref: /schemas/types.yaml#/definitions/string-array
+ minItems: 1
+ maxItems: 32
+ description:
+ A list of channels tied to this device, used for matching the
+ device to channels.
+
+ required:
+ - compatible
+ - qcom,smd-channels
+
+ additionalProperties: true
+
+ required:
+ - interrupts
+ - qcom,smd-edge
+
+ oneOf:
+ - required:
+ - mboxes
+ - required:
+ - qcom,ipc
+
+ additionalProperties: false
+
+required:
+ - compatible
+
+additionalProperties: false
+
+examples:
+ # The following example represents a smd node, with one edge representing the
+ # "rpm" subsystem. For the "rpm" subsystem we have a device tied to the
+ # "rpm_request" channel.
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ shared-memory {
+ compatible = "qcom,smd";
+
+ rpm {
+ interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+ qcom,ipc = <&apcs 8 0>;
+ qcom,smd-edge = <15>;
+
+ rpm-requests {
+ compatible = "qcom,rpm-msm8974";
+ qcom,smd-channels = "rpm_requests";
+
+ clock-controller {
+ compatible = "qcom,rpmcc-msm8974", "qcom,rpmcc";
+ #clock-cells = <1>;
+ };
+
+ };
+ };
+ };
--
2.32.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 09/10] dt-bindings: clock: qcom,rpmcc: convert to dtschema
2022-04-01 20:10 [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc Krzysztof Kozlowski
` (7 preceding siblings ...)
2022-04-01 20:10 ` [PATCH 08/10] dt-bindings: soc: qcom,smd: convert to dtschema Krzysztof Kozlowski
@ 2022-04-01 20:10 ` Krzysztof Kozlowski
2022-04-04 22:29 ` Rob Herring
2022-04-01 20:10 ` [PATCH 10/10] dt-bindings: clock: qcom,rpmcc: add clocks property Krzysztof Kozlowski
9 siblings, 1 reply; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-01 20:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
Cc: Krzysztof Kozlowski
Convert the Qualcomm RPM Clock Controller bindings to DT schema and
include it in parent's schema (SMD RPM).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../devicetree/bindings/clock/qcom,rpmcc.txt | 63 -----------------
.../devicetree/bindings/clock/qcom,rpmcc.yaml | 69 +++++++++++++++++++
.../bindings/soc/qcom/qcom,smd-rpm.yaml | 4 ++
3 files changed, 73 insertions(+), 63 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
create mode 100644 Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml
diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
deleted file mode 100644
index da295c3c004b..000000000000
--- a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
+++ /dev/null
@@ -1,63 +0,0 @@
-Qualcomm RPM Clock Controller Binding
-------------------------------------------------
-The RPM is a dedicated hardware engine for managing the shared
-SoC resources in order to keep the lowest power profile. It
-communicates with other hardware subsystems via shared memory
-and accepts clock requests, aggregates the requests and turns
-the clocks on/off or scales them on demand.
-
-Required properties :
-- compatible : shall contain only one of the following. The generic
- compatible "qcom,rpmcc" should be also included.
-
- "qcom,rpmcc-mdm9607", "qcom,rpmcc"
- "qcom,rpmcc-msm8660", "qcom,rpmcc"
- "qcom,rpmcc-apq8060", "qcom,rpmcc"
- "qcom,rpmcc-msm8226", "qcom,rpmcc"
- "qcom,rpmcc-msm8916", "qcom,rpmcc"
- "qcom,rpmcc-msm8936", "qcom,rpmcc"
- "qcom,rpmcc-msm8953", "qcom,rpmcc"
- "qcom,rpmcc-msm8974", "qcom,rpmcc"
- "qcom,rpmcc-msm8976", "qcom,rpmcc"
- "qcom,rpmcc-apq8064", "qcom,rpmcc"
- "qcom,rpmcc-ipq806x", "qcom,rpmcc"
- "qcom,rpmcc-msm8992",·"qcom,rpmcc"
- "qcom,rpmcc-msm8994",·"qcom,rpmcc"
- "qcom,rpmcc-msm8996", "qcom,rpmcc"
- "qcom,rpmcc-msm8998", "qcom,rpmcc"
- "qcom,rpmcc-qcm2290", "qcom,rpmcc"
- "qcom,rpmcc-qcs404", "qcom,rpmcc"
- "qcom,rpmcc-sdm660", "qcom,rpmcc"
- "qcom,rpmcc-sm6115", "qcom,rpmcc"
- "qcom,rpmcc-sm6125", "qcom,rpmcc"
-
-- #clock-cells : shall contain 1
-
-The clock enumerators are defined in <dt-bindings/clock/qcom,rpmcc.h>
-and come in pairs: FOO_CLK followed by FOO_A_CLK. The latter clock
-is an "active" clock, which means that the consumer only care that the
-clock is available when the apps CPU subsystem is active, i.e. not
-suspended or in deep idle. If it is important that the clock keeps running
-during system suspend, you need to specify the non-active clock, the one
-not containing *_A_* in the enumerator name.
-
-Example:
- smd {
- compatible = "qcom,smd";
-
- rpm {
- interrupts = <0 168 1>;
- qcom,ipc = <&apcs 8 0>;
- qcom,smd-edge = <15>;
-
- rpm_requests {
- compatible = "qcom,rpm-msm8916";
- qcom,smd-channels = "rpm_requests";
-
- rpmcc: clock-controller {
- compatible = "qcom,rpmcc-msm8916", "qcom,rpmcc";
- #clock-cells = <1>;
- };
- };
- };
- };
diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml b/Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml
new file mode 100644
index 000000000000..6a492b1ebc7c
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml
@@ -0,0 +1,69 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/qcom,rpmcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm RPM Clock Controller
+
+maintainers:
+ - Bjorn Andersson <bjorn.andersson@linaro.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description: |
+ The clock enumerators are defined in <dt-bindings/clock/qcom,rpmcc.h> and
+ come in pairs:: FOO_CLK followed by FOO_A_CLK. The latter clock is
+ an "active" clock, which means that the consumer only care that the clock is
+ available when the apps CPU subsystem is active, i.e. not suspended or in
+ deep idle. If it is important that the clock keeps running during system
+ suspend, you need to specify the non-active clock, the one not containing
+ *_A_* in the enumerator name.
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - qcom,rpmcc-apq8060
+ - qcom,rpmcc-apq8064
+ - qcom,rpmcc-ipq806x
+ - qcom,rpmcc-mdm9607
+ - qcom,rpmcc-msm8226
+ - qcom,rpmcc-msm8660
+ - qcom,rpmcc-msm8916
+ - qcom,rpmcc-msm8936
+ - qcom,rpmcc-msm8953
+ - qcom,rpmcc-msm8974
+ - qcom,rpmcc-msm8976
+ - qcom,rpmcc-msm8992
+ - qcom,rpmcc-msm8994
+ - qcom,rpmcc-msm8996
+ - qcom,rpmcc-msm8998
+ - qcom,rpmcc-qcm2290
+ - qcom,rpmcc-qcs404
+ - qcom,rpmcc-sdm660
+ - qcom,rpmcc-sm6115
+ - qcom,rpmcc-sm6125
+ - const: qcom,rpmcc
+
+ '#clock-cells':
+ const: 1
+
+required:
+ - compatible
+ - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ rpm {
+ rpm-requests {
+ compatible = "qcom,rpm-msm8916";
+ qcom,smd-channels = "rpm_requests";
+
+ clock-controller {
+ compatible = "qcom,rpmcc-msm8916", "qcom,rpmcc";
+ #clock-cells = <1>;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
index bf862a11f721..49e9755b3a90 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
@@ -45,6 +45,10 @@ properties:
- qcom,rpm-qcm2290
- qcom,rpm-qcs404
+ clock-controller:
+ $ref: /schemas/clock/qcom,rpmcc.yaml#
+ unevaluatedProperties: false
+
qcom,smd-channels:
$ref: /schemas/types.yaml#/definitions/string-array
description: Channel name used for the RPM communication
--
2.32.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 10/10] dt-bindings: clock: qcom,rpmcc: add clocks property
2022-04-01 20:10 [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc Krzysztof Kozlowski
` (8 preceding siblings ...)
2022-04-01 20:10 ` [PATCH 09/10] dt-bindings: clock: qcom,rpmcc: " Krzysztof Kozlowski
@ 2022-04-01 20:10 ` Krzysztof Kozlowski
2022-04-04 22:29 ` Rob Herring
9 siblings, 1 reply; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-01 20:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
Cc: Krzysztof Kozlowski
The RPM clock controller receive input clock ("xo"). It is modelled on
only one chip - MSM8953.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml b/Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml
index 6a492b1ebc7c..9d296b89a8d0 100644
--- a/Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml
@@ -48,6 +48,12 @@ properties:
'#clock-cells':
const: 1
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ const: xo
+
required:
- compatible
- '#clock-cells'
--
2.32.0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [PATCH 08/10] dt-bindings: soc: qcom,smd: convert to dtschema
2022-04-01 20:10 ` [PATCH 08/10] dt-bindings: soc: qcom,smd: convert to dtschema Krzysztof Kozlowski
@ 2022-04-02 13:46 ` Rob Herring
2022-04-02 14:54 ` Krzysztof Kozlowski
2022-04-04 22:27 ` Rob Herring
1 sibling, 1 reply; 17+ messages in thread
From: Rob Herring @ 2022-04-02 13:46 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Mathieu Poirier, Kathiravan T, linux-clk, Stephen Boyd,
linux-remoteproc, Liam Girdwood, Krzysztof Kozlowski,
linux-arm-msm, Rob Herring, devicetree, linux-kernel,
Michael Turquette, Mark Brown, Bjorn Andersson, Andy Gross
On Fri, 01 Apr 2022 22:10:33 +0200, Krzysztof Kozlowski wrote:
> Convert the Qualcomm Shared Memory Driver bindings to DT Schema.
>
> Changes against original bindings: enforce only specific names of child
> nodes, instead of any names.
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
> .../regulator/qcom,smd-rpm-regulator.yaml | 2 +-
> .../bindings/remoteproc/qcom,q6v5.txt | 2 +-
> .../bindings/remoteproc/qcom,wcnss-pil.txt | 2 +-
> .../bindings/soc/qcom/qcom,smd-rpm.yaml | 4 +-
> .../devicetree/bindings/soc/qcom/qcom,smd.txt | 98 -------------
> .../bindings/soc/qcom/qcom,smd.yaml | 137 ++++++++++++++++++
> 6 files changed, 142 insertions(+), 103 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt
> create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd.yaml
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/soc/qcom/qcom,smd.example.dt.yaml: rpm-requests: 'clock-controller' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
Documentation/devicetree/bindings/soc/qcom/qcom,smd.example.dt.yaml:0:0: /example-0/shared-memory/rpm/rpm-requests/clock-controller: failed to match any schema with compatible: ['qcom,rpmcc-msm8974', 'qcom,rpmcc']
Documentation/devicetree/bindings/soc/qcom/qcom,smd.example.dt.yaml:0:0: /example-0/shared-memory/rpm/rpm-requests/clock-controller: failed to match any schema with compatible: ['qcom,rpmcc-msm8974', 'qcom,rpmcc']
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/patch/
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 08/10] dt-bindings: soc: qcom,smd: convert to dtschema
2022-04-02 13:46 ` Rob Herring
@ 2022-04-02 14:54 ` Krzysztof Kozlowski
0 siblings, 0 replies; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-02 14:54 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski
Cc: Mathieu Poirier, Kathiravan T, linux-clk, Stephen Boyd,
linux-remoteproc, Liam Girdwood, Krzysztof Kozlowski,
linux-arm-msm, Rob Herring, devicetree, linux-kernel,
Michael Turquette, Mark Brown, Bjorn Andersson, Andy Gross
On 02/04/2022 15:46, Rob Herring wrote:
> On Fri, 01 Apr 2022 22:10:33 +0200, Krzysztof Kozlowski wrote:
>> Convert the Qualcomm Shared Memory Driver bindings to DT Schema.
>>
>> Changes against original bindings: enforce only specific names of child
>> nodes, instead of any names.
>>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>> ---
>> .../regulator/qcom,smd-rpm-regulator.yaml | 2 +-
>> .../bindings/remoteproc/qcom,q6v5.txt | 2 +-
>> .../bindings/remoteproc/qcom,wcnss-pil.txt | 2 +-
>> .../bindings/soc/qcom/qcom,smd-rpm.yaml | 4 +-
>> .../devicetree/bindings/soc/qcom/qcom,smd.txt | 98 -------------
>> .../bindings/soc/qcom/qcom,smd.yaml | 137 ++++++++++++++++++
>> 6 files changed, 142 insertions(+), 103 deletions(-)
>> delete mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt
>> create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd.yaml
>>
>
> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
> on your patch (DT_CHECKER_FLAGS is new in v5.13):
>
> yamllint warnings/errors:
>
> dtschema/dtc warnings/errors:
> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/soc/qcom/qcom,smd.example.dt.yaml: rpm-requests: 'clock-controller' does not match any of the regexes: 'pinctrl-[0-9]+'
> From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
> Documentation/devicetree/bindings/soc/qcom/qcom,smd.example.dt.yaml:0:0: /example-0/shared-memory/rpm/rpm-requests/clock-controller: failed to match any schema with compatible: ['qcom,rpmcc-msm8974', 'qcom,rpmcc']
> Documentation/devicetree/bindings/soc/qcom/qcom,smd.example.dt.yaml:0:0: /example-0/shared-memory/rpm/rpm-requests/clock-controller: failed to match any schema with compatible: ['qcom,rpmcc-msm8974', 'qcom,rpmcc']
These are being fixed by patch 9-10, so their order could be reversed to
avoid the warnings.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 08/10] dt-bindings: soc: qcom,smd: convert to dtschema
2022-04-01 20:10 ` [PATCH 08/10] dt-bindings: soc: qcom,smd: convert to dtschema Krzysztof Kozlowski
2022-04-02 13:46 ` Rob Herring
@ 2022-04-04 22:27 ` Rob Herring
1 sibling, 0 replies; 17+ messages in thread
From: Rob Herring @ 2022-04-04 22:27 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Michael Turquette, Mark Brown, Liam Girdwood, linux-clk,
linux-arm-msm, devicetree, Mathieu Poirier, linux-kernel,
Rob Herring, Bjorn Andersson, Andy Gross, Kathiravan T,
Stephen Boyd, linux-remoteproc, Krzysztof Kozlowski
On Fri, 01 Apr 2022 22:10:33 +0200, Krzysztof Kozlowski wrote:
> Convert the Qualcomm Shared Memory Driver bindings to DT Schema.
>
> Changes against original bindings: enforce only specific names of child
> nodes, instead of any names.
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
> .../regulator/qcom,smd-rpm-regulator.yaml | 2 +-
> .../bindings/remoteproc/qcom,q6v5.txt | 2 +-
> .../bindings/remoteproc/qcom,wcnss-pil.txt | 2 +-
> .../bindings/soc/qcom/qcom,smd-rpm.yaml | 4 +-
> .../devicetree/bindings/soc/qcom/qcom,smd.txt | 98 -------------
> .../bindings/soc/qcom/qcom,smd.yaml | 137 ++++++++++++++++++
> 6 files changed, 142 insertions(+), 103 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt
> create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 09/10] dt-bindings: clock: qcom,rpmcc: convert to dtschema
2022-04-01 20:10 ` [PATCH 09/10] dt-bindings: clock: qcom,rpmcc: " Krzysztof Kozlowski
@ 2022-04-04 22:29 ` Rob Herring
0 siblings, 0 replies; 17+ messages in thread
From: Rob Herring @ 2022-04-04 22:29 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: linux-kernel, Mark Brown, linux-remoteproc, Michael Turquette,
Andy Gross, Liam Girdwood, Mathieu Poirier, devicetree,
Rob Herring, linux-clk, Krzysztof Kozlowski, Bjorn Andersson,
linux-arm-msm, Kathiravan T, Stephen Boyd
On Fri, 01 Apr 2022 22:10:34 +0200, Krzysztof Kozlowski wrote:
> Convert the Qualcomm RPM Clock Controller bindings to DT schema and
> include it in parent's schema (SMD RPM).
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
> .../devicetree/bindings/clock/qcom,rpmcc.txt | 63 -----------------
> .../devicetree/bindings/clock/qcom,rpmcc.yaml | 69 +++++++++++++++++++
> .../bindings/soc/qcom/qcom,smd-rpm.yaml | 4 ++
> 3 files changed, 73 insertions(+), 63 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
> create mode 100644 Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 10/10] dt-bindings: clock: qcom,rpmcc: add clocks property
2022-04-01 20:10 ` [PATCH 10/10] dt-bindings: clock: qcom,rpmcc: add clocks property Krzysztof Kozlowski
@ 2022-04-04 22:29 ` Rob Herring
0 siblings, 0 replies; 17+ messages in thread
From: Rob Herring @ 2022-04-04 22:29 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Mark Brown, Andy Gross, linux-clk, linux-arm-msm, linux-kernel,
linux-remoteproc, devicetree, Michael Turquette,
Krzysztof Kozlowski, Liam Girdwood, Mathieu Poirier,
Kathiravan T, Bjorn Andersson, Rob Herring, Stephen Boyd
On Fri, 01 Apr 2022 22:10:35 +0200, Krzysztof Kozlowski wrote:
> The RPM clock controller receive input clock ("xo"). It is modelled on
> only one chip - MSM8953.
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
> Documentation/devicetree/bindings/clock/qcom,rpmcc.yaml | 6 ++++++
> 1 file changed, 6 insertions(+)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 06/10] ARM: dts: qcom: msm8974: override nodes by label
2022-04-01 20:10 ` [PATCH 06/10] ARM: dts: qcom: msm8974: override nodes by label Krzysztof Kozlowski
@ 2022-04-18 15:10 ` Krzysztof Kozlowski
0 siblings, 0 replies; 17+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-18 15:10 UTC (permalink / raw)
To: Bjorn Andersson, Andy Gross, Michael Turquette, Stephen Boyd,
Rob Herring, Krzysztof Kozlowski, Liam Girdwood, Mark Brown,
Mathieu Poirier, Kathiravan T, linux-arm-msm, linux-clk,
devicetree, linux-kernel, linux-remoteproc
On 01/04/2022 22:10, Krzysztof Kozlowski wrote:
> Using node paths to extend or override a device tree node is error
> prone. If there was a typo error, a new node will be created instead of
> extending the existing node. This will lead to run-time errors that
> could be hard to detect.
>
> A mistyped label on the other hand, will cause a dtc compile error
> (during build time). This also reduces the indentation making the code
> easier to read.
>
> Re-order the overrides by label name. The pre/post DTBS are the same.
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
> .../arm/boot/dts/qcom-apq8074-dragonboard.dts | 614 +++++-----
> .../boot/dts/qcom-msm8974-fairphone-fp2.dts | 581 +++++----
> .../qcom-msm8974-lge-nexus5-hammerhead.dts | 1075 ++++++++--------
> .../boot/dts/qcom-msm8974-samsung-klte.dts | 1083 ++++++++---------
> .../dts/qcom-msm8974-sony-xperia-amami.dts | 569 +++++----
> .../dts/qcom-msm8974-sony-xperia-castor.dts | 908 +++++++-------
> .../dts/qcom-msm8974-sony-xperia-honami.dts | 636 +++++-----
> arch/arm/boot/dts/qcom-msm8974.dtsi | 16 +-
> 8 files changed, 2730 insertions(+), 2752 deletions(-)
>
Hi Bjorn,
I see you applied other arm-dts patches from this set, except this one.
Any comments here? This is quite a big one, so maybe it had trouble
making through the discussion lists?
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2022-04-18 15:42 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-04-01 20:10 [PATCH 00/10] qcom: convert to dtschema qcom,smd and qcom,rpmcc Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 01/10] arm64: dts: qcom: msm8953: do not use underscore in node name Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 02/10] arm64: dts: qcom: msm8994: remove SMD qcom,local-pid property Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 03/10] arm64: dts: qcom: add RPM clock controller fallback compatible Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 04/10] ARM: dts: qcom: msm8974-lge-nexus5: move gpio-keys out of soc Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 05/10] ARM: dts: qcom: msm8974-samsung-klte: " Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 06/10] ARM: dts: qcom: msm8974: override nodes by label Krzysztof Kozlowski
2022-04-18 15:10 ` Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 07/10] ARM: dts: qcom: do not use underscore in node name Krzysztof Kozlowski
2022-04-01 20:10 ` [PATCH 08/10] dt-bindings: soc: qcom,smd: convert to dtschema Krzysztof Kozlowski
2022-04-02 13:46 ` Rob Herring
2022-04-02 14:54 ` Krzysztof Kozlowski
2022-04-04 22:27 ` Rob Herring
2022-04-01 20:10 ` [PATCH 09/10] dt-bindings: clock: qcom,rpmcc: " Krzysztof Kozlowski
2022-04-04 22:29 ` Rob Herring
2022-04-01 20:10 ` [PATCH 10/10] dt-bindings: clock: qcom,rpmcc: add clocks property Krzysztof Kozlowski
2022-04-04 22:29 ` Rob Herring
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).