[PATCH 0/7] arm64: dts: qcom: sm8450: Add QUP and DMA nodes

[PATCH 0/7] arm64: dts: qcom: sm8450: Add QUP and DMA nodes

[Vinod Koul]

This series adds the gpi_dma nodes followed by the i2c and spi nodes for the
three qups found in the SM8450 SoC.

While at it, iommus was missing for qup0/qup1, so fix that up too.

Lastly enable the spi and i2c nodes found on the QRD board.

Vinod Koul (7):
  arm64: dts: qcom: sm8450: Add gpi_dma nodes
  arm64: dts: qcom: sm8450: Fix missing iommus for qup
  arm64: dts: qcom: sm8450: Add qup nodes for qup0
  arm64: dts: qcom: sm8450: Add qup nodes for qup1
  arm64: dts: qcom: sm8450: Add qup nodes for qup2
  arm64: dts: qcom: sm8450: Fix missing iommus for qup1
  arm64: dts: qcom: sm8450-qrd: Enable spi and i2c nodes

 arch/arm64/boot/dts/qcom/sm8450-qrd.dts |   24 +
 arch/arm64/boot/dts/qcom/sm8450.dtsi    | 1240 +++++++++++++++++++++++
 2 files changed, 1264 insertions(+)

-- 
2.34.1

[PATCH 1/7] arm64: dts: qcom: sm8450: Add gpi_dma nodes

[Vinod Koul]

GPI DMA can be used for DMA operations for QUP devices, so add the three
gpi_dma insances found in this SoC

Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 67 ++++++++++++++++++++++++++++
 1 file changed, 67 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 934e29b9e153..bfbb6e04fcb4 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -6,6 +6,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-sm8450.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/dma/qcom-gpi.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
@@ -687,6 +688,50 @@ gcc: clock-controller@100000 {
 			clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
 		};
 
+		gpi_dma2: dma-controller@800000 {
+			compatible = "qcom,sm8450-gpi-dma";
+			#dma-cells = <3>;
+			reg = <0 0x800000 0 0x60000>;
+			interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 599 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0x7e>;
+			iommus = <&apps_smmu 0x496 0x0>;
+			status = "disabled";
+		};
+
+		gpi_dma0: dma-controller@900000 {
+			compatible = "qcom,sm8450-gpi-dma";
+			#dma-cells = <3>;
+			reg = <0 0x900000 0 0x60000>;
+			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0x7e>;
+			iommus = <&apps_smmu 0x5b6 0x0>;
+			status = "disabled";
+		};
+
 		qupv3_id_0: geniqup@9c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0x0 0x009c0000 0x0 0x2000>;
@@ -712,6 +757,28 @@ uart7: serial@99c000 {
 			};
 		};
 
+		gpi_dma1: dma-controller@a00000 {
+			compatible = "qcom,sm8450-gpi-dma";
+			#dma-cells = <3>;
+			reg = <0 0xa00000 0 0x60000>;
+			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0x7e>;
+			iommus = <&apps_smmu 0x56 0x0>;
+			status = "disabled";
+		};
+
 		qupv3_id_1: geniqup@ac0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0x0 0x00ac0000 0x0 0x6000>;
-- 
2.34.1

[PATCH 2/7] arm64: dts: qcom: sm8450: Fix missing iommus for qup

[Vinod Koul]

qupv3_id_0 was missing iommus property which cause any dma transaction
to fail and board crash. So add the missing iommus.

While at it also add interconnect nodes for qup

Fixes: 5188049c9b36 ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index bfbb6e04fcb4..93ff677f0d35 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -738,6 +738,9 @@ qupv3_id_0: geniqup@9c0000 {
 			clock-names = "m-ahb", "s-ahb";
 			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
 				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x5a3 0x0>;
+			interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>;
+			interconnect-names = "qup-core";
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
-- 
2.34.1

[PATCH 3/7] arm64: dts: qcom: sm8450: Add qup nodes for qup0

[Vinod Koul]

qup0 has 7 SEs, with SE7 as uart and already added, so add the
remaining 6 SEs (i2c and spi) along with pinconf for these SEs

Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 412 +++++++++++++++++++++++++++
 1 file changed, 412 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 93ff677f0d35..48f8035ea200 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -334,6 +334,25 @@ CLUSTER_PD: cpu-cluster0 {
 		};
 	};
 
+	qup_opp_table_100mhz: qup-100mhz-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-50000000 {
+			opp-hz = /bits/ 64 <50000000>;
+			required-opps = <&rpmhpd_opp_min_svs>;
+		};
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+	};
+
 	reserved_memory: reserved-memory {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -746,6 +765,292 @@ qupv3_id_0: geniqup@9c0000 {
 			ranges;
 			status = "disabled";
 
+			i2c0: i2c@980000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00980000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_data_clk>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00980000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>;
+				power-domains = <&rpmhpd SM8450_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@984000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00984000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c1_data_clk>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi1: spi@984000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00984000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@988000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00988000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c2_data_clk>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi2: spi@988000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00988000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+
+			i2c3: i2c@98c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x0098c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c3_data_clk>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi3: spi@98c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x0098c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@990000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00990000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c4_data_clk>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi4: spi@990000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00990000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
+				power-domains = <&rpmhpd SM8450_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c5: i2c@994000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00994000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c5_data_clk>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi5: spi@994000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00994000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+
+			i2c6: i2c@998000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x998000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c6_data_clk>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi6: spi@998000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x998000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
 			uart7: serial@99c000 {
 				compatible = "qcom,geni-debug-uart";
 				reg = <0 0x0099c000 0 0x4000>;
@@ -1121,6 +1426,41 @@ tlmm: pinctrl@f100000 {
 			gpio-ranges = <&tlmm 0 0 211>;
 			wakeup-parent = <&pdc>;
 
+			qup_i2c0_data_clk: qup-i2c0-data-clk {
+				pins = "gpio0", "gpio1";
+				function = "qup0";
+			};
+
+			qup_i2c1_data_clk: qup-i2c1-data-clk {
+				pins = "gpio4", "gpio5";
+				function = "qup1";
+			};
+
+			qup_i2c2_data_clk: qup-i2c2-data-clk {
+				pins = "gpio8", "gpio9";
+				function = "qup2";
+			};
+
+			qup_i2c3_data_clk: qup-i2c3-data-clk {
+				pins = "gpio12", "gpio13";
+				function = "qup3";
+			};
+
+			qup_i2c4_data_clk: qup-i2c4-data-clk {
+				pins = "gpio16", "gpio17";
+				function = "qup4";
+			};
+
+			qup_i2c5_data_clk: qup-i2c5-data-clk {
+				pins = "gpio206", "gpio207";
+				function = "qup5";
+			};
+
+			qup_i2c6_data_clk: qup-i2c6-data-clk {
+				pins = "gpio20", "gpio21";
+				function = "qup6";
+			};
+
 			qup_i2c13_data_clk: qup-i2c13-data-clk {
 				pins = "gpio48", "gpio49";
 				function = "qup13";
@@ -1135,6 +1475,78 @@ qup_i2c14_data_clk: qup-i2c14-data-clk {
 				bias-pull-up;
 			};
 
+			qup_spi0_cs: qup-spi0-cs {
+				pins = "gpio3";
+				function = "qup0";
+			};
+
+			qup_spi0_data_clk: qup-spi0-data-clk {
+				pins = "gpio0", "gpio1", "gpio2";
+				function = "qup0";
+			};
+
+			qup_spi1_cs: qup-spi1-cs {
+				pins = "gpio7";
+				function = "qup1";
+			};
+
+			qup_spi1_data_clk: qup-spi1-data-clk {
+				pins = "gpio4", "gpio5", "gpio6";
+				function = "qup1";
+			};
+
+			qup_spi2_cs: qup-spi2-cs {
+				pins = "gpio11";
+				function = "qup2";
+			};
+
+			qup_spi2_data_clk: qup-spi2-data-clk {
+				pins = "gpio8", "gpio9", "gpio10";
+				function = "qup2";
+			};
+
+			qup_spi3_cs: qup-spi3-cs {
+				pins = "gpio15";
+				function = "qup3";
+			};
+
+			qup_spi3_data_clk: qup-spi3-data-clk {
+				pins = "gpio12", "gpio13", "gpio14";
+				function = "qup3";
+			};
+
+			qup_spi4_cs: qup-spi4-cs {
+				pins = "gpio19";
+				function = "qup4";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi4_data_clk: qup-spi4-data-clk {
+				pins = "gpio16", "gpio17", "gpio18";
+				function = "qup4";
+			};
+
+			qup_spi5_cs: qup-spi5-cs {
+				pins = "gpio85";
+				function = "qup5";
+			};
+
+			qup_spi5_data_clk: qup-spi5-data-clk {
+				pins = "gpio206", "gpio207", "gpio84";
+				function = "qup5";
+			};
+
+			qup_spi6_cs: qup-spi6-cs {
+				pins = "gpio23";
+				function = "qup6";
+			};
+
+			qup_spi6_data_clk: qup-spi6-data-clk {
+				pins = "gpio20", "gpio21", "gpio22";
+				function = "qup6";
+			};
+
 			qup_uart7_rx: qup-uart7-rx {
 				pins = "gpio26";
 				function = "qup7";
-- 
2.34.1

[PATCH 4/7] arm64: dts: qcom: sm8450: Add qup nodes for qup1

[Vinod Koul]

qup1 has 7 SEs, I2C13 and I2C14 were already added so added the
remaining SEs (i2c and spi) along with pinconf for these SEs
Also add interconnect properties for I2C13 and I2C14

Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 359 +++++++++++++++++++++++++++
 1 file changed, 359 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 48f8035ea200..3097a6e3ab4e 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -1098,6 +1098,206 @@ qupv3_id_1: geniqup@ac0000 {
 			ranges;
 			status = "disabled";
 
+			i2c8: i2c@a80000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a80000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c8_data_clk>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi8: spi@a80000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a80000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c9: i2c@a84000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a84000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c9_data_clk>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi9: spi@a84000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a84000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c10: i2c@a88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a88000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c10_data_clk>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi10: spi@a88000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a88000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c11: i2c@a8c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a8c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c11_data_clk>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi11: spi@a8c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a8c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c12: i2c@a90000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a90000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c12_data_clk>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi12: spi@a90000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a90000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
 			i2c13: i2c@a94000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0 0x00a94000 0 0x4000>;
@@ -1106,6 +1306,33 @@ i2c13: i2c@a94000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c13_data_clk>;
 				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi13: spi@a94000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a94000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1119,6 +1346,33 @@ i2c14: i2c@a98000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c14_data_clk>;
 				interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi14: spi@a98000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a98000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1461,6 +1715,31 @@ qup_i2c6_data_clk: qup-i2c6-data-clk {
 				function = "qup6";
 			};
 
+			qup_i2c8_data_clk: qup-i2c8-data-clk {
+				pins = "gpio28", "gpio29";
+				function = "qup8";
+			};
+
+			qup_i2c9_data_clk: qup-i2c9-data-clk {
+				pins = "gpio32", "gpio33";
+				function = "qup9";
+			};
+
+			qup_i2c10_data_clk: qup-i2c10-data-clk {
+				pins = "gpio36", "gpio37";
+				function = "qup10";
+			};
+
+			qup_i2c11_data_clk: qup-i2c11-data-clk {
+				pins = "gpio40", "gpio41";
+				function = "qup11";
+			};
+
+			qup_i2c12_data_clk: qup-i2c12-data-clk {
+				pins = "gpio44", "gpio45";
+				function = "qup12";
+			};
+
 			qup_i2c13_data_clk: qup-i2c13-data-clk {
 				pins = "gpio48", "gpio49";
 				function = "qup13";
@@ -1547,6 +1826,86 @@ qup_spi6_data_clk: qup-spi6-data-clk {
 				function = "qup6";
 			};
 
+			qup_spi8_cs: qup-spi8-cs {
+				pins = "gpio31";
+				function = "qup8";
+			};
+
+			qup_spi8_data_clk: qup-spi8-data-clk {
+				pins = "gpio28", "gpio29", "gpio30";
+				function = "qup8";
+			};
+
+			qup_spi9_cs: qup-spi9-cs {
+				pins = "gpio35";
+				function = "qup9";
+			};
+
+			qup_spi9_data_clk: qup-spi9-data-clk {
+				pins = "gpio32", "gpio33", "gpio34";
+				function = "qup9";
+			};
+
+			qup_spi10_cs: qup-spi10-cs {
+				pins = "gpio39";
+				function = "qup10";
+			};
+
+			qup_spi10_data_clk: qup-spi10-data-clk {
+				pins = "gpio36", "gpio37", "gpio38";
+				function = "qup10";
+			};
+
+			qup_spi11_cs: qup-spi11-cs {
+				pins = "gpio43";
+				function = "qup11";
+			};
+
+			qup_spi11_data_clk: qup-spi11-data-clk {
+				pins = "gpio40", "gpio41", "gpio42";
+				function = "qup11";
+			};
+
+			qup_spi12_cs: qup-spi12-cs {
+				pins = "gpio47";
+				function = "qup12";
+			};
+
+			qup_spi12_data_clk: qup-spi12-data-clk {
+				pins = "gpio44", "gpio45", "gpio46";
+				function = "qup12";
+			};
+
+			qup_spi13_cs: qup-spi13-cs {
+				pins = "gpio51";
+				function = "qup13";
+			};
+
+			qup_spi13_data_clk: qup-spi13-data-clk {
+				pins = "gpio48", "gpio49", "gpio50";
+				function = "qup13";
+			};
+
+			qup_spi14_cs: qup-spi14-cs {
+				pins = "gpio55";
+				function = "qup14";
+			};
+
+			qup_spi14_data_clk: qup-spi14-data-clk {
+				pins = "gpio52", "gpio53", "gpio54";
+				function = "qup14";
+			};
+
+			qup_spi15_cs: qup-spi15-cs {
+				pins = "gpio59";
+				function = "qup15";
+			};
+
+			qup_spi15_data_clk: qup-spi15-data-clk {
+				pins = "gpio56", "gpio57", "gpio58";
+				function = "qup15";
+			};
+
 			qup_uart7_rx: qup-uart7-rx {
 				pins = "gpio26";
 				function = "qup7";
-- 
2.34.1

[PATCH 5/7] arm64: dts: qcom: sm8450: Add qup nodes for qup2

[Vinod Koul]

qup2 has 7 SEs, so add the SEs (i2c and spi) along with pinconf for
these SEs

Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 396 +++++++++++++++++++++++++++
 1 file changed, 396 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 3097a6e3ab4e..067568c13448 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -729,6 +729,299 @@ gpi_dma2: dma-controller@800000 {
 			status = "disabled";
 		};
 
+		qupv3_id_2: geniqup@8c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x008c0000 0x0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x483 0x0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			i2c15: i2c@880000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00880000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c15_data_clk>;
+				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi15: spi@880000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00880000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c16: i2c@884000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00884000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c16_data_clk>;
+				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi16: spi@884000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00884000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi16_data_clk>, <&qup_spi16_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c17: i2c@888000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00888000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c17_data_clk>;
+				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi17: spi@888000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00888000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi17_data_clk>, <&qup_spi17_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c18: i2c@88c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x0088c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c18_data_clk>;
+				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi18: spi@88c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0088c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi18_data_clk>, <&qup_spi18_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c19: i2c@890000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00890000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c19_data_clk>;
+				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi19: spi@890000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00890000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi19_data_clk>, <&qup_spi19_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c20: i2c@894000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00894000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c20_data_clk>;
+				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi20: spi@894000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00894000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi20_data_clk>, <&qup_spi20_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c21: i2c@898000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00898000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c21_data_clk>;
+				interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi21: spi@898000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00898000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
+				interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi21_data_clk>, <&qup_spi21_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
 		gpi_dma0: dma-controller@900000 {
 			compatible = "qcom,sm8450-gpi-dma";
 			#dma-cells = <3>;
@@ -1754,6 +2047,41 @@ qup_i2c14_data_clk: qup-i2c14-data-clk {
 				bias-pull-up;
 			};
 
+			qup_i2c15_data_clk: qup-i2c15-data-clk {
+				pins = "gpio56", "gpio57";
+				function = "qup15";
+			};
+
+			qup_i2c16_data_clk: qup-i2c16-data-clk {
+				pins = "gpio60", "gpio61";
+				function = "qup16";
+			};
+
+			qup_i2c17_data_clk: qup-i2c17-data-clk {
+				pins = "gpio64", "gpio65";
+				function = "qup17";
+			};
+
+			qup_i2c18_data_clk: qup-i2c18-data-clk {
+				pins = "gpio68", "gpio69";
+				function = "qup18";
+			};
+
+			qup_i2c19_data_clk: qup-i2c19-data-clk {
+				pins = "gpio72", "gpio73";
+				function = "qup19";
+			};
+
+			qup_i2c20_data_clk: qup-i2c20-data-clk {
+				pins = "gpio76", "gpio77";
+				function = "qup20";
+			};
+
+			qup_i2c21_data_clk: qup-i2c21-data-clk {
+				pins = "gpio80", "gpio81";
+				function = "qup21";
+			};
+
 			qup_spi0_cs: qup-spi0-cs {
 				pins = "gpio3";
 				function = "qup0";
@@ -1906,6 +2234,74 @@ qup_spi15_data_clk: qup-spi15-data-clk {
 				function = "qup15";
 			};
 
+			qup_spi16_cs: qup-spi16-cs {
+				pins = "gpio63";
+				function = "qup16";
+			};
+
+			qup_spi16_data_clk: qup-spi16-data-clk {
+				pins = "gpio60", "gpio61", "gpio62";
+				function = "qup16";
+			};
+
+			qup_spi17_cs: qup-spi17-cs {
+				pins = "gpio67";
+				function = "qup17";
+			};
+
+			qup_spi17_data_clk: qup-spi17-data-clk {
+				pins = "gpio64", "gpio65", "gpio66";
+				function = "qup17";
+			};
+
+			qup_spi18_cs: qup-spi18-cs {
+				pins = "gpio71";
+				function = "qup18";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi18_data_clk: qup-spi18-data-clk {
+				pins = "gpio68", "gpio69", "gpio70";
+				function = "qup18";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi19_cs: qup-spi19-cs {
+				pins = "gpio75";
+				function = "qup19";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi19_data_clk: qup-spi19-data-clk {
+				pins = "gpio72", "gpio73", "gpio74";
+				function = "qup19";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi20_cs: qup-spi20-cs {
+				pins = "gpio79";
+				function = "qup20";
+			};
+
+			qup_spi20_data_clk: qup-spi20-data-clk {
+				pins = "gpio76", "gpio77", "gpio78";
+				function = "qup20";
+			};
+
+			qup_spi21_cs: qup-spi21-cs {
+				pins = "gpio83";
+				function = "qup21";
+			};
+
+			qup_spi21_data_clk: qup-spi21-data-clk {
+				pins = "gpio80", "gpio81", "gpio82";
+				function = "qup21";
+			};
+
 			qup_uart7_rx: qup-uart7-rx {
 				pins = "gpio26";
 				function = "qup7";
-- 
2.34.1

[PATCH 6/7] arm64: dts: qcom: sm8450: Fix missing iommus for qup1

[Vinod Koul]

qupv3_id_1 was missing iommus property which cause any dma transaction
to fail and board crash. So add the missing iommus.

Fixes: 5188049c9b36 ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 067568c13448..88ec7fe455cf 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -1386,6 +1386,9 @@ qupv3_id_1: geniqup@ac0000 {
 			clock-names = "m-ahb", "s-ahb";
 			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
 				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x43 0x0>;
+			interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>;
+			interconnect-names = "qup-core";
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
-- 
2.34.1

[PATCH 7/7] arm64: dts: qcom: sm8450-qrd: Enable spi and i2c nodes

[Vinod Koul]

Enable the i2c5, spi4, spi18 and spi19 nodes which were tested on qrd
board along with related qup nodes and gpi_dma0

Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450-qrd.dts b/arch/arm64/boot/dts/qcom/sm8450-qrd.dts
index 9526632d4029..1e87a083816e 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-qrd.dts
@@ -342,10 +342,22 @@ vreg_l6e_1p2: ldo6 {
 	};
 };
 
+&gpi_dma0 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
 
+&qupv3_id_2 {
+	status = "okay";
+};
+
 &remoteproc_adsp {
 	status = "okay";
 	firmware-name = "qcom/sm8450/adsp.mbn";
@@ -366,6 +378,18 @@ &remoteproc_slpi {
 	firmware-name = "qcom/sm8450/slpi.mbn";
 };
 
+&spi4 {
+	status = "okay";
+};
+
+&spi18 {
+	status = "okay";
+};
+
+&spi19 {
+	status = "okay";
+};
+
 &tlmm {
 	gpio-reserved-ranges = <28 4>, <36 4>;
 };
-- 
2.34.1

Re: [PATCH 0/7] arm64: dts: qcom: sm8450: Add QUP and DMA nodes

[Bjorn Andersson]

On Thu, 14 Apr 2022 15:46:23 +0530, Vinod Koul wrote:
> This series adds the gpi_dma nodes followed by the i2c and spi nodes for the
> three qups found in the SM8450 SoC.
> 
> While at it, iommus was missing for qup0/qup1, so fix that up too.
> 
> Lastly enable the spi and i2c nodes found on the QRD board.
> 
> [...]

Applied, thanks!

[1/7] arm64: dts: qcom: sm8450: Add gpi_dma nodes
      commit: b9c8433083097327cad19fbf633fb0735a008315
[2/7] arm64: dts: qcom: sm8450: Fix missing iommus for qup
      commit: 488922c1a372579bf2caf40933e7459e3c86276f
[3/7] arm64: dts: qcom: sm8450: Add qup nodes for qup0
      commit: a84e88e9a00334f1468a9f69a77091dbe80b7a3b
[4/7] arm64: dts: qcom: sm8450: Add qup nodes for qup1
      commit: 1a380216fd6fcf7135b2b413bb9431fc98e2fa23
[5/7] arm64: dts: qcom: sm8450: Add qup nodes for qup2
      commit: ba640cd31342b45dcf2f95f6ca7dcbc46629919f
[6/7] arm64: dts: qcom: sm8450: Fix missing iommus for qup1
      commit: 67ebdc6dd1e2049fd9620f0572bc81a809afbe24
[7/7] arm64: dts: qcom: sm8450-qrd: Enable spi and i2c nodes
      commit: d953239726e971ecaee45d86b4bcd605be839b2a

Best regards,
-- 
Bjorn Andersson <bjorn.andersson@linaro.org>