From: Robert Marko <robert.marko@sartura.hr>
To: robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org,
andrew@lunn.ch, gregory.clement@bootlin.com,
sebastian.hesselbarth@gmail.com, shawnguo@kernel.org,
linus.walleij@linaro.org, kostap@marvell.com,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, pali@kernel.org,
marek.behun@nic.cz
Cc: Robert Marko <robert.marko@sartura.hr>
Subject: [PATCH 2/2] arm64: dts: marvell: add support for Methode eDPU
Date: Mon, 9 May 2022 13:00:28 +0200 [thread overview]
Message-ID: <20220509110028.144226-2-robert.marko@sartura.hr> (raw)
In-Reply-To: <20220509110028.144226-1-robert.marko@sartura.hr>
Methode eDPU is an Armada 3720 powered board based on the Methode uDPU.
They feature the same CPU, RAM, and storage as well as the form factor.
However, eDPU only has one SFP slot plus a copper G.hn port.
In order to reduce duplication, split the uDPU DTS into a common one.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
---
arch/arm64/boot/dts/marvell/Makefile | 1 +
.../boot/dts/marvell/armada-3720-eDPU.dts | 14 ++
.../boot/dts/marvell/armada-3720-uDPU.dts | 148 +---------------
.../boot/dts/marvell/armada-3720-uDPU.dtsi | 163 ++++++++++++++++++
4 files changed, 179 insertions(+), 147 deletions(-)
create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts
create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 1c794cdcb8e6..104d7d7e8215 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -1,6 +1,7 @@
# SPDX-License-Identifier: GPL-2.0
# Mvebu SoC Family
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-eDPU.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts b/arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts
new file mode 100644
index 000000000000..6b573a6854cc
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "armada-3720-uDPU.dtsi"
+
+/ {
+ model = "Methode eDPU Board";
+ compatible = "methode,edpu", "marvell,armada3720";
+};
+
+ð0 {
+ phy-mode = "2500base-x";
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
index 95d46e8d081c..b146fae9f60b 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
@@ -1,67 +1,13 @@
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Device tree for the uDPU board.
- * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
- * Copyright (C) 2016 Marvell
- * Copyright (C) 2019 Methode Electronics
- * Copyright (C) 2019 Telus
- *
- * Vladimir Vid <vladimir.vid@sartura.hr>
- */
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include "armada-372x.dtsi"
+#include "armada-3720-uDPU.dtsi"
/ {
model = "Methode uDPU Board";
compatible = "methode,udpu", "marvell,armada3720";
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
- };
-
- leds {
- pinctrl-names = "default";
- compatible = "gpio-leds";
-
- power1 {
- label = "udpu:green:power";
- gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
- };
-
- power2 {
- label = "udpu:red:power";
- gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
- };
-
- network1 {
- label = "udpu:green:network";
- gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
- };
-
- network2 {
- label = "udpu:red:network";
- gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
- };
-
- alarm1 {
- label = "udpu:green:alarm";
- gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
- };
-
- alarm2 {
- label = "udpu:red:alarm";
- gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
- };
- };
-
sfp_eth0: sfp-eth0 {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
@@ -71,50 +17,6 @@ sfp_eth0: sfp-eth0 {
tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
maximum-power-milliwatt = <3000>;
};
-
- sfp_eth1: sfp-eth1 {
- compatible = "sff,sfp";
- i2c-bus = <&i2c1>;
- los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
- mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
- tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
- tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
- maximum-power-milliwatt = <3000>;
- };
-};
-
-&sdhci0 {
- status = "okay";
- bus-width = <8>;
- mmc-ddr-1_8v;
- mmc-hs400-1_8v;
- marvell,pad-type = "fixed-1-8v";
- non-removable;
- no-sd;
- no-sdio;
-};
-
-&spi0 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&spi_quad_pins>;
-
- m25p80@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <54000000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
- /* only bootloader is located on the SPI */
- partition@0 {
- label = "uboot";
- reg = <0 0x400000>;
- };
- };
- };
};
&pinctrl_nb {
@@ -122,11 +24,6 @@ i2c1_recovery_pins: i2c1-recovery-pins {
groups = "i2c1";
function = "gpio";
};
-
- i2c2_recovery_pins: i2c2-recovery-pins {
- groups = "i2c2";
- function = "gpio";
- };
};
&i2c0 {
@@ -139,50 +36,7 @@ &i2c0 {
sda-gpios = <&gpionb 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
};
-&i2c1 {
- status = "okay";
- pinctrl-names = "default", "recovery";
- pinctrl-0 = <&i2c2_pins>;
- pinctrl-1 = <&i2c2_recovery_pins>;
- /delete-property/mrvl,i2c-fast-mode;
- scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-
- lm75@48 {
- status = "okay";
- compatible = "lm75";
- reg = <0x48>;
- };
-
- lm75@49 {
- status = "okay";
- compatible = "lm75";
- reg = <0x49>;
- };
-};
-
ð0 {
phy-mode = "sgmii";
- status = "okay";
- managed = "in-band-status";
- phys = <&comphy1 0>;
sfp = <&sfp_eth0>;
};
-
-ð1 {
- phy-mode = "sgmii";
- status = "okay";
- managed = "in-band-status";
- phys = <&comphy0 1>;
- sfp = <&sfp_eth1>;
-};
-
-&usb3 {
- status = "okay";
- phys = <&usb2_utmi_otg_phy>;
- phy-names = "usb2-utmi-otg-phy";
-};
-
-&uart0 {
- status = "okay";
-};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi
new file mode 100644
index 000000000000..5e38acc92a31
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device tree for the uDPU board.
+ * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
+ * Copyright (C) 2016 Marvell
+ * Copyright (C) 2019 Methode Electronics
+ * Copyright (C) 2019 Telus
+ *
+ * Vladimir Vid <vladimir.vid@sartura.hr>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-372x.dtsi"
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+ };
+
+ leds {
+ pinctrl-names = "default";
+ compatible = "gpio-leds";
+
+ power1 {
+ label = "udpu:green:power";
+ gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
+ };
+
+ power2 {
+ label = "udpu:red:power";
+ gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
+ };
+
+ network1 {
+ label = "udpu:green:network";
+ gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
+ };
+
+ network2 {
+ label = "udpu:red:network";
+ gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
+ };
+
+ alarm1 {
+ label = "udpu:green:alarm";
+ gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
+ };
+
+ alarm2 {
+ label = "udpu:red:alarm";
+ gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ sfp_eth1: sfp-eth1 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c1>;
+ los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
+ maximum-power-milliwatt = <3000>;
+ };
+};
+
+&sdhci0 {
+ status = "okay";
+ bus-width = <8>;
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ marvell,pad-type = "fixed-1-8v";
+ non-removable;
+ no-sd;
+ no-sdio;
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_quad_pins>;
+
+ spi-flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <54000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /* only bootloader is located on the SPI */
+ partition@0 {
+ label = "firmware";
+ reg = <0x0 0x180000>;
+ };
+
+ partition@180000 {
+ label = "u-boot-env";
+ reg = <0x180000 0x10000>;
+ };
+ };
+ };
+};
+
+&pinctrl_nb {
+ i2c2_recovery_pins: i2c2-recovery-pins {
+ groups = "i2c2";
+ function = "gpio";
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ pinctrl-names = "default", "recovery";
+ pinctrl-0 = <&i2c2_pins>;
+ pinctrl-1 = <&i2c2_recovery_pins>;
+ /delete-property/mrvl,i2c-fast-mode;
+ scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+ nct375@48 {
+ status = "okay";
+ compatible = "ti,tmp75c";
+ reg = <0x48>;
+ };
+
+ nct375@49 {
+ status = "okay";
+ compatible = "ti,tmp75c";
+ reg = <0x49>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ managed = "in-band-status";
+ phys = <&comphy1 0>;
+};
+
+ð1 {
+ phy-mode = "sgmii";
+ status = "okay";
+ managed = "in-band-status";
+ phys = <&comphy0 1>;
+ sfp = <&sfp_eth1>;
+};
+
+&usb3 {
+ status = "okay";
+ phys = <&usb2_utmi_otg_phy>;
+ phy-names = "usb2-utmi-otg-phy";
+};
+
+&uart0 {
+ status = "okay";
+};
--
2.36.0
next prev parent reply other threads:[~2022-05-09 11:00 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-05-09 11:00 [PATCH 1/2] dt-bindings: vendor-prefixes: add Methode Electronics Robert Marko
2022-05-09 11:00 ` Robert Marko [this message]
2022-05-10 10:20 ` [PATCH 2/2] arm64: dts: marvell: add support for Methode eDPU Krzysztof Kozlowski
2022-05-10 11:41 ` Robert Marko
2022-05-10 11:46 ` Krzysztof Kozlowski
2022-05-10 12:43 ` Robert Marko
2022-05-10 12:50 ` Krzysztof Kozlowski
2022-05-10 10:20 ` [PATCH 1/2] dt-bindings: vendor-prefixes: add Methode Electronics Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220509110028.144226-2-robert.marko@sartura.hr \
--to=robert.marko@sartura.hr \
--cc=andrew@lunn.ch \
--cc=devicetree@vger.kernel.org \
--cc=gregory.clement@bootlin.com \
--cc=kostap@marvell.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marek.behun@nic.cz \
--cc=pali@kernel.org \
--cc=robh+dt@kernel.org \
--cc=sebastian.hesselbarth@gmail.com \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).