linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: linux-usb@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org
Subject: [PATCH 2/2] usb: typec: mux: Introduce GPIO-based SBU mux
Date: Wed, 10 Aug 2022 13:47:50 -0700	[thread overview]
Message-ID: <20220810204750.3672362-3-bjorn.andersson@linaro.org> (raw)
In-Reply-To: <20220810204750.3672362-1-bjorn.andersson@linaro.org>

A design found in various Qualcomm-based boards is to use a USB switch,
controlled through a pair of GPIO lines to connect, disconnect and
switch the orientation of the SBU lines in USB Type-C applications.

This introduces a generic driver, which implements the typec_switch and
typec_mux interfaces to perform these operations.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 drivers/usb/typec/mux/Kconfig        |   6 +
 drivers/usb/typec/mux/Makefile       |   1 +
 drivers/usb/typec/mux/gpio-sbu-mux.c | 171 +++++++++++++++++++++++++++
 3 files changed, 178 insertions(+)
 create mode 100644 drivers/usb/typec/mux/gpio-sbu-mux.c

diff --git a/drivers/usb/typec/mux/Kconfig b/drivers/usb/typec/mux/Kconfig
index 5eb2c17d72c1..c46fa4f9d3df 100644
--- a/drivers/usb/typec/mux/Kconfig
+++ b/drivers/usb/typec/mux/Kconfig
@@ -12,6 +12,12 @@ config TYPEC_MUX_FSA4480
 	  common USB Type-C connector.
 	  If compiled as a module, the module will be named fsa4480.
 
+config TYPEC_MUX_GPIO_SBU
+	tristate "Generic GPIO based SBU mux for USB Type-C applications"
+	help
+	  Say Y or M if your system uses a GPIO based mux for managing the
+	  connected state and the swapping of the SBU lines in a Type-C port.
+
 config TYPEC_MUX_PI3USB30532
 	tristate "Pericom PI3USB30532 Type-C cross switch driver"
 	depends on I2C
diff --git a/drivers/usb/typec/mux/Makefile b/drivers/usb/typec/mux/Makefile
index e52a56c16bfb..dda67e19b58b 100644
--- a/drivers/usb/typec/mux/Makefile
+++ b/drivers/usb/typec/mux/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 
 obj-$(CONFIG_TYPEC_MUX_FSA4480)		+= fsa4480.o
+obj-$(CONFIG_TYPEC_MUX_GPIO_SBU)	+= gpio-sbu-mux.o
 obj-$(CONFIG_TYPEC_MUX_PI3USB30532)	+= pi3usb30532.o
 obj-$(CONFIG_TYPEC_MUX_INTEL_PMC)	+= intel_pmc_mux.o
diff --git a/drivers/usb/typec/mux/gpio-sbu-mux.c b/drivers/usb/typec/mux/gpio-sbu-mux.c
new file mode 100644
index 000000000000..35f7bd3029a9
--- /dev/null
+++ b/drivers/usb/typec/mux/gpio-sbu-mux.c
@@ -0,0 +1,171 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Linaro Ltd.
+ */
+
+#include <linux/bits.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/gpio/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/usb/typec_dp.h>
+#include <linux/usb/typec_mux.h>
+
+struct gpio_sbu_mux {
+	struct gpio_desc *enable_gpio;
+	struct gpio_desc *select_gpio;
+
+	struct typec_switch_dev *sw;
+	struct typec_mux_dev *mux;
+
+	struct mutex lock; /* protect enabled and swapped */
+	bool enabled;
+	bool swapped;
+};
+
+static int gpio_sbu_switch_set(struct typec_switch_dev *sw,
+			       enum typec_orientation orientation)
+{
+	struct gpio_sbu_mux *sbu_mux = typec_switch_get_drvdata(sw);
+	bool enabled;
+	bool swapped;
+
+	mutex_lock(&sbu_mux->lock);
+
+	enabled = sbu_mux->enabled;
+
+	switch (orientation) {
+	case TYPEC_ORIENTATION_NONE:
+		enabled = false;
+		break;
+	case TYPEC_ORIENTATION_NORMAL:
+		swapped = false;
+		break;
+	case TYPEC_ORIENTATION_REVERSE:
+		swapped = true;
+		break;
+	}
+
+	if (enabled != sbu_mux->enabled)
+		gpiod_set_value(sbu_mux->enable_gpio, enabled);
+
+	if (swapped != sbu_mux->swapped)
+		gpiod_set_value(sbu_mux->select_gpio, swapped);
+
+	sbu_mux->enabled = enabled;
+	sbu_mux->swapped = swapped;
+
+	mutex_unlock(&sbu_mux->lock);
+
+	return 0;
+}
+
+static int gpio_sbu_mux_set(struct typec_mux_dev *mux,
+			    struct typec_mux_state *state)
+{
+	struct gpio_sbu_mux *sbu_mux = typec_mux_get_drvdata(mux);
+
+	mutex_lock(&sbu_mux->lock);
+
+	switch (state->mode) {
+	case TYPEC_STATE_SAFE:
+	case TYPEC_STATE_USB:
+		sbu_mux->enabled = false;
+		break;
+	case TYPEC_DP_STATE_C:
+	case TYPEC_DP_STATE_D:
+	case TYPEC_DP_STATE_E:
+		sbu_mux->enabled = true;
+		break;
+	default:
+		break;
+	}
+
+	gpiod_set_value(sbu_mux->enable_gpio, sbu_mux->enabled);
+
+	mutex_unlock(&sbu_mux->lock);
+
+	return 0;
+}
+
+static int gpio_sbu_mux_probe(struct platform_device *pdev)
+{
+	struct typec_switch_desc sw_desc = { };
+	struct typec_mux_desc mux_desc = { };
+	struct device *dev = &pdev->dev;
+	struct gpio_sbu_mux *sbu_mux;
+
+	sbu_mux = devm_kzalloc(dev, sizeof(*sbu_mux), GFP_KERNEL);
+	if (!sbu_mux)
+		return -ENOMEM;
+
+	mutex_init(&sbu_mux->lock);
+
+	sbu_mux->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW);
+	if (IS_ERR(sbu_mux->enable_gpio))
+		return dev_err_probe(dev, PTR_ERR(sbu_mux->enable_gpio),
+				     "unable to acquire enable gpio\n");
+
+	sbu_mux->select_gpio = devm_gpiod_get(dev, "select", GPIOD_OUT_LOW);
+	if (IS_ERR(sbu_mux->select_gpio))
+		return dev_err_probe(dev, PTR_ERR(sbu_mux->select_gpio),
+				     "unable to acquire select gpio\n");
+
+	sw_desc.drvdata = sbu_mux;
+	sw_desc.fwnode = dev_fwnode(dev);
+	sw_desc.set = gpio_sbu_switch_set;
+
+	sbu_mux->sw = typec_switch_register(dev, &sw_desc);
+	if (IS_ERR(sbu_mux->sw))
+		return dev_err_probe(dev, PTR_ERR(sbu_mux->sw),
+				     "failed to register typec switch\n");
+
+	mux_desc.drvdata = sbu_mux;
+	mux_desc.fwnode = dev_fwnode(dev);
+	mux_desc.set = gpio_sbu_mux_set;
+
+	sbu_mux->mux = typec_mux_register(dev, &mux_desc);
+	if (IS_ERR(sbu_mux->mux)) {
+		typec_switch_unregister(sbu_mux->sw);
+		return dev_err_probe(dev, PTR_ERR(sbu_mux->mux),
+				     "failed to register typec mux\n");
+	}
+
+	platform_set_drvdata(pdev, sbu_mux);
+
+	return 0;
+}
+
+static int gpio_sbu_mux_remove(struct platform_device *pdev)
+{
+	struct gpio_sbu_mux *sbu_mux = platform_get_drvdata(pdev);
+
+	gpiod_set_value(sbu_mux->enable_gpio, 0);
+
+	typec_mux_unregister(sbu_mux->mux);
+	typec_switch_unregister(sbu_mux->sw);
+
+	return 0;
+}
+
+static const struct of_device_id gpio_sbu_mux_match[] = {
+	{ .compatible = "gpio-sbu-mux", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, gpio_sbu_mux_match);
+
+static struct platform_driver gpio_sbu_mux_driver = {
+	.probe = gpio_sbu_mux_probe,
+	.remove = gpio_sbu_mux_remove,
+	.driver = {
+		.name = "gpio_sbu_mux",
+		.of_match_table = gpio_sbu_mux_match,
+	},
+};
+module_platform_driver(gpio_sbu_mux_driver);
+
+MODULE_DESCRIPTION("GPIO based SBU mux driver");
+MODULE_LICENSE("GPL");
-- 
2.35.1


      parent reply	other threads:[~2022-08-10 20:45 UTC|newest]

Thread overview: 22+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-08-10 20:47 [PATCH 0/2] usb: typec: mux: GPIO-based SBU mux Bjorn Andersson
2022-08-10 20:47 ` [PATCH 1/2] dt-bindings: usb: Introduce " Bjorn Andersson
2022-08-11  9:14   ` Krzysztof Kozlowski
2022-08-14 21:01     ` Rob Herring
2022-08-17 23:00       ` Bjorn Andersson
2022-08-19  1:09         ` Stephen Boyd
2022-08-19 20:14           ` Prashant Malani
2022-08-19 20:49             ` Stephen Boyd
2022-08-19 21:39               ` Bjorn Andersson
2022-08-19 22:18                 ` Prashant Malani
2022-08-20  4:04                   ` Bjorn Andersson
2022-08-23 18:21                     ` Prashant Malani
2022-08-19 22:00             ` Bjorn Andersson
2022-08-19 22:55               ` Prashant Malani
2022-08-20  4:09                 ` Bjorn Andersson
2022-08-23 18:54                   ` Prashant Malani
2022-08-26  3:02                     ` Bjorn Andersson
2022-08-19 21:26           ` Bjorn Andersson
2022-08-20  3:51             ` Stephen Boyd
2022-08-20  4:56               ` Bjorn Andersson
2022-08-26  1:49                 ` Stephen Boyd
2022-08-10 20:47 ` Bjorn Andersson [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220810204750.3672362-3-bjorn.andersson@linaro.org \
    --to=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=heikki.krogerus@linux.intel.com \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).