linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH 0/2] arm64: meson: add support for JetHome JetHub D1p (j110)
@ 2022-08-11 10:31 Vyacheslav Bocharov
  2022-08-11 10:31 ` [PATCH 1/2] arm64: dts: meson-axg: add support for " Vyacheslav Bocharov
                   ` (2 more replies)
  0 siblings, 3 replies; 6+ messages in thread
From: Vyacheslav Bocharov @ 2022-08-11 10:31 UTC (permalink / raw)
  To: Neil Armstrong
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, Rob Herring, devicetree

- add support for JetHome JetHub D1p (https://jethome.ru/d1p) is a home
automation controller with the following features:
  - DIN Rail Mounting
  - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
  - no video out
  - 1/2/4GB LPDDR4
  - 8/16/32GB eMMC flash
  - 1 x USB 2.0
  - 1 x 10/100Mbps ethernet
  - WiFi / Bluetooth Realtek 8822CS or similar IEEE 802.11a/b/g/n/ac
  - TI CC2652P1 Zigbee Wireless Module with up to 20dBm output power
    and Zigbee 3.0 support.
  - 2 x gpio LEDS
  - GPIO user Button
  - 1 x 1-Wire
  - 2 x RS-485
  - 4 x dry contact digital GPIO inputs
  - 3 x relay GPIO outputs
  - DC source with a voltage of 9 to 56 V / Active POE

- unify device tree files for JetHub D1/D1p devices

Vyacheslav Bocharov (2):
  arm64: dts: meson-axg: add support for JetHub D1p (j110)
  dt-bindings: arm: amlogic: add bindings for Jethub D1p (j110)

 .../devicetree/bindings/arm/amlogic.yaml      |   1 +
 arch/arm64/boot/dts/amlogic/Makefile          |   2 +
 .../amlogic/meson-axg-jethome-jethub-j100.dts | 338 +----------------
 .../meson-axg-jethome-jethub-j110-rev-2.dts   |  37 ++
 .../meson-axg-jethome-jethub-j110-rev-3.dts   |  27 ++
 .../meson-axg-jethome-jethub-j1xx.dtsi        | 351 ++++++++++++++++++
 6 files changed, 422 insertions(+), 334 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi

-- 
2.30.2


^ permalink raw reply	[flat|nested] 6+ messages in thread

* [PATCH 1/2] arm64: dts: meson-axg: add support for JetHub D1p (j110)
  2022-08-11 10:31 [PATCH 0/2] arm64: meson: add support for JetHome JetHub D1p (j110) Vyacheslav Bocharov
@ 2022-08-11 10:31 ` Vyacheslav Bocharov
  2022-08-16  9:59   ` Neil Armstrong
  2022-08-11 10:31 ` [PATCH 2/2] dt-bindings: arm: amlogic: add bindings for Jethub " Vyacheslav Bocharov
  2022-08-16 12:22 ` [PATCH 0/2] arm64: meson: add support for JetHome JetHub " Neil Armstrong
  2 siblings, 1 reply; 6+ messages in thread
From: Vyacheslav Bocharov @ 2022-08-11 10:31 UTC (permalink / raw)
  To: Neil Armstrong
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, Rob Herring, devicetree

- add support for JetHome JetHub D1p (https://jethome.ru/d1p) is a home
automation controller with the following features:
  - DIN Rail Mounting
  - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
  - no video out
  - 1/2/4GB LPDDR4
  - 8/16/32GB eMMC flash
  - 1 x USB 2.0
  - 1 x 10/100Mbps ethernet
  - WiFi / Bluetooth Realtek 8822CS or similar IEEE 802.11a/b/g/n/ac
  - TI CC2652P1 Zigbee Wireless Module with up to 20dBm output power
    and Zigbee 3.0 support.
  - 2 x gpio LEDS
  - GPIO user Button
  - 1 x 1-Wire
  - 2 x RS-485
  - 4 x dry contact digital GPIO inputs
  - 3 x relay GPIO outputs
  - DC source with a voltage of 9 to 56 V / Active POE

- unify device tree files for JetHub D1/D1p devices

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   2 +
 .../amlogic/meson-axg-jethome-jethub-j100.dts | 338 +----------------
 .../meson-axg-jethome-jethub-j110-rev-2.dts   |  37 ++
 .../meson-axg-jethome-jethub-j110-rev-3.dts   |  27 ++
 .../meson-axg-jethome-jethub-j1xx.dtsi        | 351 ++++++++++++++++++
 5 files changed, 421 insertions(+), 334 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 8773211df50e..33e9c96af099 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,6 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j110-rev-2.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j110-rev-3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-radxa-zero.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
index 8b0d586aa84e..b2d6ba660914 100644
--- a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -1,270 +1,29 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
- * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
- * Copyright (c) 2020 JetHome
- * Author: Aleksandr Kazantsev <ak@tvip.ru>
- * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2022 JetHome
  * Author: Vyacheslav Bocharov <adeep@lexina.in>
  */
 
 /dts-v1/;
 
-#include "meson-axg.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/thermal/thermal.h>
+#include "meson-axg-jethome-jethub-j1xx.dtsi"
 
 / {
 	compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
-	model = "JetHome JetHub J100";
-	aliases {
-		serial0 = &uart_AO;   /* Console */
-		serial2 = &uart_AO_B; /* External UART (Wireless Module) */
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
+	model = "JetHome JetHub D1 (J100)";
 
 	/* 1024MB RAM */
 	memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
 	};
-
-	reserved-memory {
-		linux,cma {
-			size = <0x0 0x400000>;
-		};
-	};
-
-	emmc_pwrseq: emmc-pwrseq {
-		compatible = "mmc-pwrseq-emmc";
-		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
-	};
-
-	vcc_3v3: regulator-vcc_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vcc_5v: regulator-vcc_5v {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-	};
-
-	vddao_3v3: regulator-vddao_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&vcc_5v>;
-		regulator-always-on;
-	};
-
-	vddio_ao18: regulator-vddio_ao18 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDIO_AO18";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vddio_boot: regulator-vddio_boot {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDIO_BOOT";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vccq_1v8: regulator-vccq_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCCQ_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	usb_pwr: regulator-usb_pwr {
-		compatible = "regulator-fixed";
-		regulator-name = "USB_PWR";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc_5v>;
-		regulator-always-on;
-	};
-
-	sdio_pwrseq: sdio-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
-		clocks = <&wifi32k>;
-		clock-names = "ext_clock";
-	};
-
-	wifi32k: wifi32k {
-		compatible = "pwm-clock";
-		#clock-cells = <0>;
-		clock-frequency = <32768>;
-		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
-	};
-
-	thermal-zones {
-		cpu_thermal: cpu-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-			thermal-sensors = <&scpi_sensors 0>;
-			trips {
-				cpu_passive: cpu-passive {
-					temperature = <70000>; /* millicelsius */
-					hysteresis = <2000>; /* millicelsius */
-					type = "passive";
-				};
-
-				cpu_hot: cpu-hot {
-					temperature = <80000>; /* millicelsius */
-					hysteresis = <2000>; /* millicelsius */
-					type = "hot";
-				};
-
-				cpu_critical: cpu-critical {
-					temperature = <100000>; /* millicelsius */
-					hysteresis = <2000>; /* millicelsius */
-					type = "critical";
-				};
-			};
-
-			cpu_cooling_maps: cooling-maps {
-				map0 {
-					trip = <&cpu_passive>;
-					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-
-				map1 {
-					trip = <&cpu_hot>;
-					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-			};
-		};
-	};
-
-	onewire {
-		compatible = "w1-gpio";
-		gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>;
-		#gpio-cells = <1>;
-	};
-};
-
-&efuse {
-	sn: sn@32 {
-		reg = <0x32 0x20>;
-	};
-
-	eth_mac: eth_mac@0 {
-		reg = <0x0 0x6>;
-	};
-
-	bt_mac: bt_mac@6 {
-		reg = <0x6 0x6>;
-	};
-
-	wifi_mac: wifi_mac@c {
-		reg = <0xc 0x6>;
-	};
-
-	bid: bid@12 {
-		reg = <0x12 0x20>;
-	};
-};
-
-&ethmac {
-	status = "okay";
-	pinctrl-0 = <&eth_rmii_x_pins>;
-	pinctrl-names = "default";
-	phy-handle = <&eth_phy0>;
-	phy-mode = "rmii";
-
-	mdio {
-		compatible = "snps,dwmac-mdio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
-		eth_phy0: ethernet-phy@0 {
-			/* compatible = "ethernet-phy-id0243.0c54";*/
-			max-speed = <100>;
-			reg = <0>;
-
-			reset-assert-us = <10000>;
-			reset-deassert-us = <10000>;
-			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
-		};
-	};
-};
-
-/* Internal I2C bus (on CPU module) */
-&i2c1 {
-	status = "okay";
-	pinctrl-0 = <&i2c1_z_pins>;
-	pinctrl-names = "default";
-
-	/* RTC */
-	pcf8563: pcf8563@51 {
-		compatible = "nxp,pcf8563";
-		reg = <0x51>;
-		status = "okay";
-	};
 };
 
-/* Peripheral I2C bus (on motherboard) */
-&i2c_AO {
-	status = "okay";
-	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
-	pinctrl-names = "default";
-};
-
-&pwm_ab {
-	status = "okay";
-	pinctrl-0 = <&pwm_a_x20_pins>;
-	pinctrl-names = "default";
-};
 
 /* wifi module */
 &sd_emmc_b {
-	status = "okay";
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	pinctrl-0 = <&sdio_pins>;
-	pinctrl-1 = <&sdio_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	max-frequency = <50000000>;
 	non-removable;
-	disable-wp;
-
-	mmc-pwrseq = <&sdio_pwrseq>;
-
-	vmmc-supply = <&vddao_3v3>;
-	vqmmc-supply = <&vddio_boot>;
 
 	brcmf: wifi@1 {
 		reg = <1>;
@@ -272,99 +31,10 @@ brcmf: wifi@1 {
 	};
 };
 
-/* emmc storage */
-&sd_emmc_c {
-	status = "okay";
-	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
-	pinctrl-1 = <&emmc_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <8>;
-	cap-mmc-highspeed;
-	max-frequency = <200000000>;
-	non-removable;
-	disable-wp;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
-
-	mmc-pwrseq = <&emmc_pwrseq>;
-
-	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&vccq_1v8>;
-};
-
 /* UART Bluetooth */
 &uart_B {
-	status = "okay";
-	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
-	pinctrl-names = "default";
-	uart-has-rtscts;
-
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
 		shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
 	};
 };
-
-/* UART Console */
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
-/* UART Wireless module */
-&uart_AO_B {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_b_pins>;
-	pinctrl-names = "default";
-};
-
-&usb {
-	status = "okay";
-	phy-supply = <&usb_pwr>;
-};
-
-&spicc1 {
-	status = "okay";
-	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
-	pinctrl-names = "default";
-};
-
-&gpio {
-	gpio-line-names =
-		"", "", "", "", "", // 0 - 4
-		"", "", "", "", "", // 5 - 9
-		"UserButton", "", "", "", "", // 10 - 14
-		"", "", "", "", "", // 15 - 19
-		"", "", "", "", "", // 20 - 24
-		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
-		"Output1", "", "", "", "", // 30 - 34
-		"", "ZigBeeBOOT", "", "", "", // 35 - 39
-		"1Wire", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
-		"Input2", "Input1", "", "", "", // 45 - 49
-		"", "", "", "", "", // 50 - 54
-		"", "", "", "", "", // 55 - 59
-		"", "", "", "", "", // 60 - 64
-		"", "", "", "", "", // 65 - 69
-		"", "", "", "", "", // 70 - 74
-		"", "", "", "", "", // 75 - 79
-		"", "", "", "", "", // 80 - 84
-		"", ""; // 85-86
-};
-
-&cpu0 {
-	#cooling-cells = <2>;
-};
-
-&cpu1 {
-	#cooling-cells = <2>;
-};
-
-&cpu2 {
-	#cooling-cells = <2>;
-};
-
-&cpu3 {
-	#cooling-cells = <2>;
-};
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts
new file mode 100644
index 000000000000..0062667c4f65
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2022 JetHome
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-axg-jethome-jethub-j1xx.dtsi"
+
+/ {
+	compatible = "jethome,jethub-j110", "amlogic,a113d", "amlogic,meson-axg";
+	model = "JetHome JetHub D1p (J110) HW rev.2";
+
+	/* 2GiB or 4GiB RAM */
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+
+/* wifi module */
+&sd_emmc_b {
+	broken-cd;/* cd-gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;*/
+};
+
+/* UART Bluetooth */
+&uart_B {
+	bluetooth {
+		compatible = "realtek,rtl8822cs-bt";
+		enable-gpios  = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+		host-wake-gpios = <&gpio GPIOZ_8 GPIO_ACTIVE_HIGH>;
+		device-wake-gpios = <&gpio GPIOZ_6 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts
new file mode 100644
index 000000000000..c2d22b00c1cd
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2022 JetHome
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-axg-jethome-jethub-j1xx.dtsi"
+
+/ {
+	compatible = "jethome,jethub-j110", "amlogic,a113d", "amlogic,meson-axg";
+	model = "JetHome JetHub D1p (J110) Hw rev.3";
+
+	/* 2GiB or 4GiB RAM */
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+
+/* wifi module */
+&sd_emmc_b {
+	broken-cd;/* cd-gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;*/
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi
new file mode 100644
index 000000000000..5836b0030931
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi
@@ -0,0 +1,351 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2022 JetHome
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial2 = &uart_AO_B; /* External UART (Wireless Module) */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x400000>;
+		};
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vccq_1v8: regulator-vccq_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCCQ_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	usb_pwr: regulator-usb_pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&scpi_sensors 0>;
+			trips {
+				cpu_passive: cpu-passive {
+					temperature = <70000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				cpu_hot: cpu-hot {
+					temperature = <80000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "hot";
+				};
+
+				cpu_critical: cpu-critical {
+					temperature = <100000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+
+			cpu_cooling_maps: cooling-maps {
+				map0 {
+					trip = <&cpu_passive>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&cpu_hot>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	onewire {
+		compatible = "w1-gpio";
+		gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>;
+		#gpio-cells = <1>;
+	};
+};
+
+&efuse {
+	sn: sn@32 {
+		reg = <0x32 0x20>;
+	};
+
+	eth_mac: eth_mac@0 {
+		reg = <0x0 0x6>;
+	};
+
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@c {
+		reg = <0xc 0x6>;
+	};
+
+	bid: bid@12 {
+		reg = <0x12 0x20>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rmii_x_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+		eth_phy0: ethernet-phy@0 {
+			/* compatible = "ethernet-phy-id0243.0c54";*/
+			max-speed = <100>;
+			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+	status = "okay";
+	pinctrl-0 = <&i2c1_z_pins>;
+	pinctrl-names = "default";
+
+	/* RTC */
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+	status = "okay";
+	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ab {
+	status = "okay";
+	pinctrl-0 = <&pwm_a_x20_pins>;
+	pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* emmc storage */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vccq_1v8>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+	status = "okay";
+	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+/* UART Console */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+	status = "okay";
+	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
+	pinctrl-names = "default";
+};
+
+&gpio {
+	gpio-line-names =
+		"", "", "", "", "", // 0 - 4
+		"", "", "", "", "", // 5 - 9
+		"UserButton", "", "", "", "", // 10 - 14
+		"", "", "", "", "", // 15 - 19
+		"", "", "", "", "", // 20 - 24
+		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
+		"Output1", "", "", "", "", // 30 - 34
+		"", "ZigBeeBOOT", "", "", "", // 35 - 39
+		"1Wire", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+		"Input2", "Input1", "", "", "", // 45 - 49
+		"", "", "", "", "", // 50 - 54
+		"", "", "", "", "", // 55 - 59
+		"", "", "", "", "", // 60 - 64
+		"", "", "", "", "", // 65 - 69
+		"", "", "", "", "", // 70 - 74
+		"", "", "", "", "", // 75 - 79
+		"", "", "", "", "", // 80 - 84
+		"", ""; // 85-86
+};
+
+&cpu0 {
+	#cooling-cells = <2>;
+};
+
+&cpu1 {
+	#cooling-cells = <2>;
+};
+
+&cpu2 {
+	#cooling-cells = <2>;
+};
+
+&cpu3 {
+	#cooling-cells = <2>;
+};
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 6+ messages in thread

* [PATCH 2/2] dt-bindings: arm: amlogic: add bindings for Jethub D1p (j110)
  2022-08-11 10:31 [PATCH 0/2] arm64: meson: add support for JetHome JetHub D1p (j110) Vyacheslav Bocharov
  2022-08-11 10:31 ` [PATCH 1/2] arm64: dts: meson-axg: add support for " Vyacheslav Bocharov
@ 2022-08-11 10:31 ` Vyacheslav Bocharov
  2022-08-14 21:26   ` Rob Herring
  2022-08-16 12:22 ` [PATCH 0/2] arm64: meson: add support for JetHome JetHub " Neil Armstrong
  2 siblings, 1 reply; 6+ messages in thread
From: Vyacheslav Bocharov @ 2022-08-11 10:31 UTC (permalink / raw)
  To: Neil Armstrong
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, Rob Herring, devicetree

JetHome JetHub D1p is a home automation controller, modification
 of JetHub D1 based on Amlogic A113X

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 61a6cabb375b..9ac73e961146 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -136,6 +136,7 @@ properties:
           - enum:
               - amlogic,s400
               - jethome,jethub-j100
+              - jethome,jethub-j110
           - const: amlogic,a113d
           - const: amlogic,meson-axg
 
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 6+ messages in thread

* Re: [PATCH 2/2] dt-bindings: arm: amlogic: add bindings for Jethub D1p (j110)
  2022-08-11 10:31 ` [PATCH 2/2] dt-bindings: arm: amlogic: add bindings for Jethub " Vyacheslav Bocharov
@ 2022-08-14 21:26   ` Rob Herring
  0 siblings, 0 replies; 6+ messages in thread
From: Rob Herring @ 2022-08-14 21:26 UTC (permalink / raw)
  To: Vyacheslav Bocharov
  Cc: linux-kernel, Neil Armstrong, linux-arm-kernel, Rob Herring,
	devicetree, linux-amlogic

On Thu, 11 Aug 2022 13:31:13 +0300, Vyacheslav Bocharov wrote:
> JetHome JetHub D1p is a home automation controller, modification
>  of JetHub D1 based on Amlogic A113X
> 
> Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
> ---
>  Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH 1/2] arm64: dts: meson-axg: add support for JetHub D1p (j110)
  2022-08-11 10:31 ` [PATCH 1/2] arm64: dts: meson-axg: add support for " Vyacheslav Bocharov
@ 2022-08-16  9:59   ` Neil Armstrong
  0 siblings, 0 replies; 6+ messages in thread
From: Neil Armstrong @ 2022-08-16  9:59 UTC (permalink / raw)
  To: Vyacheslav Bocharov
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, Rob Herring, devicetree

On 11/08/2022 12:31, Vyacheslav Bocharov wrote:
> - add support for JetHome JetHub D1p (https://jethome.ru/d1p) is a home
> automation controller with the following features:
>    - DIN Rail Mounting
>    - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
>    - no video out
>    - 1/2/4GB LPDDR4
>    - 8/16/32GB eMMC flash
>    - 1 x USB 2.0
>    - 1 x 10/100Mbps ethernet
>    - WiFi / Bluetooth Realtek 8822CS or similar IEEE 802.11a/b/g/n/ac
>    - TI CC2652P1 Zigbee Wireless Module with up to 20dBm output power
>      and Zigbee 3.0 support.
>    - 2 x gpio LEDS
>    - GPIO user Button
>    - 1 x 1-Wire
>    - 2 x RS-485
>    - 4 x dry contact digital GPIO inputs
>    - 3 x relay GPIO outputs
>    - DC source with a voltage of 9 to 56 V / Active POE
> 
> - unify device tree files for JetHub D1/D1p devices
> 
> Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
> ---
>   arch/arm64/boot/dts/amlogic/Makefile          |   2 +
>   .../amlogic/meson-axg-jethome-jethub-j100.dts | 338 +----------------
>   .../meson-axg-jethome-jethub-j110-rev-2.dts   |  37 ++
>   .../meson-axg-jethome-jethub-j110-rev-3.dts   |  27 ++
>   .../meson-axg-jethome-jethub-j1xx.dtsi        | 351 ++++++++++++++++++
>   5 files changed, 421 insertions(+), 334 deletions(-)
>   create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts
>   create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts
>   create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 8773211df50e..33e9c96af099 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -1,6 +1,8 @@
>   # SPDX-License-Identifier: GPL-2.0
>   dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j110-rev-2.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j110-rev-3.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-g12a-radxa-zero.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> index 8b0d586aa84e..b2d6ba660914 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> @@ -1,270 +1,29 @@
>   // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>   /*
> - * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
> - * Copyright (c) 2020 JetHome
> - * Author: Aleksandr Kazantsev <ak@tvip.ru>
> - * Author: Alexey Shevelkin <ash@tvip.ru>
> + * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
> + * Copyright (c) 2022 JetHome
>    * Author: Vyacheslav Bocharov <adeep@lexina.in>
>    */
>   
>   /dts-v1/;
>   
> -#include "meson-axg.dtsi"
> -#include <dt-bindings/input/input.h>
> -#include <dt-bindings/thermal/thermal.h>
> +#include "meson-axg-jethome-jethub-j1xx.dtsi"
>   
>   / {
>   	compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
> -	model = "JetHome JetHub J100";
> -	aliases {
> -		serial0 = &uart_AO;   /* Console */
> -		serial2 = &uart_AO_B; /* External UART (Wireless Module) */
> -		ethernet0 = &ethmac;
> -	};
> -
> -	chosen {
> -		stdout-path = "serial0:115200n8";
> -	};
> +	model = "JetHome JetHub D1 (J100)";
>   
>   	/* 1024MB RAM */
>   	memory@0 {
>   		device_type = "memory";
>   		reg = <0x0 0x0 0x0 0x40000000>;
>   	};
> -
> -	reserved-memory {
> -		linux,cma {
> -			size = <0x0 0x400000>;
> -		};
> -	};
> -
> -	emmc_pwrseq: emmc-pwrseq {
> -		compatible = "mmc-pwrseq-emmc";
> -		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> -	};
> -
> -	vcc_3v3: regulator-vcc_3v3 {
> -		compatible = "regulator-fixed";
> -		regulator-name = "VCC_3V3";
> -		regulator-min-microvolt = <3300000>;
> -		regulator-max-microvolt = <3300000>;
> -		vin-supply = <&vddao_3v3>;
> -		regulator-always-on;
> -	};
> -
> -	vcc_5v: regulator-vcc_5v {
> -		compatible = "regulator-fixed";
> -		regulator-name = "VCC5V";
> -		regulator-min-microvolt = <5000000>;
> -		regulator-max-microvolt = <5000000>;
> -		regulator-always-on;
> -	};
> -
> -	vddao_3v3: regulator-vddao_3v3 {
> -		compatible = "regulator-fixed";
> -		regulator-name = "VDDAO_3V3";
> -		regulator-min-microvolt = <3300000>;
> -		regulator-max-microvolt = <3300000>;
> -		vin-supply = <&vcc_5v>;
> -		regulator-always-on;
> -	};
> -
> -	vddio_ao18: regulator-vddio_ao18 {
> -		compatible = "regulator-fixed";
> -		regulator-name = "VDDIO_AO18";
> -		regulator-min-microvolt = <1800000>;
> -		regulator-max-microvolt = <1800000>;
> -		vin-supply = <&vddao_3v3>;
> -		regulator-always-on;
> -	};
> -
> -	vddio_boot: regulator-vddio_boot {
> -		compatible = "regulator-fixed";
> -		regulator-name = "VDDIO_BOOT";
> -		regulator-min-microvolt = <3300000>;
> -		regulator-max-microvolt = <3300000>;
> -		vin-supply = <&vddao_3v3>;
> -		regulator-always-on;
> -	};
> -
> -	vccq_1v8: regulator-vccq_1v8 {
> -		compatible = "regulator-fixed";
> -		regulator-name = "VCCQ_1V8";
> -		regulator-min-microvolt = <1800000>;
> -		regulator-max-microvolt = <1800000>;
> -		vin-supply = <&vddao_3v3>;
> -		regulator-always-on;
> -	};
> -
> -	usb_pwr: regulator-usb_pwr {
> -		compatible = "regulator-fixed";
> -		regulator-name = "USB_PWR";
> -		regulator-min-microvolt = <5000000>;
> -		regulator-max-microvolt = <5000000>;
> -		vin-supply = <&vcc_5v>;
> -		regulator-always-on;
> -	};
> -
> -	sdio_pwrseq: sdio-pwrseq {
> -		compatible = "mmc-pwrseq-simple";
> -		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
> -		clocks = <&wifi32k>;
> -		clock-names = "ext_clock";
> -	};
> -
> -	wifi32k: wifi32k {
> -		compatible = "pwm-clock";
> -		#clock-cells = <0>;
> -		clock-frequency = <32768>;
> -		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
> -	};
> -
> -	thermal-zones {
> -		cpu_thermal: cpu-thermal {
> -			polling-delay-passive = <250>;
> -			polling-delay = <1000>;
> -			thermal-sensors = <&scpi_sensors 0>;
> -			trips {
> -				cpu_passive: cpu-passive {
> -					temperature = <70000>; /* millicelsius */
> -					hysteresis = <2000>; /* millicelsius */
> -					type = "passive";
> -				};
> -
> -				cpu_hot: cpu-hot {
> -					temperature = <80000>; /* millicelsius */
> -					hysteresis = <2000>; /* millicelsius */
> -					type = "hot";
> -				};
> -
> -				cpu_critical: cpu-critical {
> -					temperature = <100000>; /* millicelsius */
> -					hysteresis = <2000>; /* millicelsius */
> -					type = "critical";
> -				};
> -			};
> -
> -			cpu_cooling_maps: cooling-maps {
> -				map0 {
> -					trip = <&cpu_passive>;
> -					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> -							<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> -							<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> -							<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> -				};
> -
> -				map1 {
> -					trip = <&cpu_hot>;
> -					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> -							<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> -							<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> -							<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> -				};
> -			};
> -		};
> -	};
> -
> -	onewire {
> -		compatible = "w1-gpio";
> -		gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>;
> -		#gpio-cells = <1>;
> -	};
> -};
> -
> -&efuse {
> -	sn: sn@32 {
> -		reg = <0x32 0x20>;
> -	};
> -
> -	eth_mac: eth_mac@0 {
> -		reg = <0x0 0x6>;
> -	};
> -
> -	bt_mac: bt_mac@6 {
> -		reg = <0x6 0x6>;
> -	};
> -
> -	wifi_mac: wifi_mac@c {
> -		reg = <0xc 0x6>;
> -	};
> -
> -	bid: bid@12 {
> -		reg = <0x12 0x20>;
> -	};
> -};
> -
> -&ethmac {
> -	status = "okay";
> -	pinctrl-0 = <&eth_rmii_x_pins>;
> -	pinctrl-names = "default";
> -	phy-handle = <&eth_phy0>;
> -	phy-mode = "rmii";
> -
> -	mdio {
> -		compatible = "snps,dwmac-mdio";
> -		#address-cells = <1>;
> -		#size-cells = <0>;
> -
> -		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
> -		eth_phy0: ethernet-phy@0 {
> -			/* compatible = "ethernet-phy-id0243.0c54";*/
> -			max-speed = <100>;
> -			reg = <0>;
> -
> -			reset-assert-us = <10000>;
> -			reset-deassert-us = <10000>;
> -			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
> -		};
> -	};
> -};
> -
> -/* Internal I2C bus (on CPU module) */
> -&i2c1 {
> -	status = "okay";
> -	pinctrl-0 = <&i2c1_z_pins>;
> -	pinctrl-names = "default";
> -
> -	/* RTC */
> -	pcf8563: pcf8563@51 {
> -		compatible = "nxp,pcf8563";
> -		reg = <0x51>;
> -		status = "okay";
> -	};
>   };
>   
> -/* Peripheral I2C bus (on motherboard) */
> -&i2c_AO {
> -	status = "okay";
> -	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
> -	pinctrl-names = "default";
> -};
> -
> -&pwm_ab {
> -	status = "okay";
> -	pinctrl-0 = <&pwm_a_x20_pins>;
> -	pinctrl-names = "default";
> -};
>   
>   /* wifi module */
>   &sd_emmc_b {
> -	status = "okay";
> -	#address-cells = <1>;
> -	#size-cells = <0>;
> -
> -	pinctrl-0 = <&sdio_pins>;
> -	pinctrl-1 = <&sdio_clk_gate_pins>;
> -	pinctrl-names = "default", "clk-gate";
> -
> -	bus-width = <4>;
> -	cap-sd-highspeed;
> -	max-frequency = <50000000>;
>   	non-removable;
> -	disable-wp;
> -
> -	mmc-pwrseq = <&sdio_pwrseq>;
> -
> -	vmmc-supply = <&vddao_3v3>;
> -	vqmmc-supply = <&vddio_boot>;
>   
>   	brcmf: wifi@1 {
>   		reg = <1>;
> @@ -272,99 +31,10 @@ brcmf: wifi@1 {
>   	};
>   };
>   
> -/* emmc storage */
> -&sd_emmc_c {
> -	status = "okay";
> -	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> -	pinctrl-1 = <&emmc_clk_gate_pins>;
> -	pinctrl-names = "default", "clk-gate";
> -
> -	bus-width = <8>;
> -	cap-mmc-highspeed;
> -	max-frequency = <200000000>;
> -	non-removable;
> -	disable-wp;
> -	mmc-ddr-1_8v;
> -	mmc-hs200-1_8v;
> -
> -	mmc-pwrseq = <&emmc_pwrseq>;
> -
> -	vmmc-supply = <&vcc_3v3>;
> -	vqmmc-supply = <&vccq_1v8>;
> -};
> -
>   /* UART Bluetooth */
>   &uart_B {
> -	status = "okay";
> -	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
> -	pinctrl-names = "default";
> -	uart-has-rtscts;
> -
>   	bluetooth {
>   		compatible = "brcm,bcm43438-bt";
>   		shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
>   	};
>   };
> -
> -/* UART Console */
> -&uart_AO {
> -	status = "okay";
> -	pinctrl-0 = <&uart_ao_a_pins>;
> -	pinctrl-names = "default";
> -};
> -
> -/* UART Wireless module */
> -&uart_AO_B {
> -	status = "okay";
> -	pinctrl-0 = <&uart_ao_b_pins>;
> -	pinctrl-names = "default";
> -};
> -
> -&usb {
> -	status = "okay";
> -	phy-supply = <&usb_pwr>;
> -};
> -
> -&spicc1 {
> -	status = "okay";
> -	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
> -	pinctrl-names = "default";
> -};
> -
> -&gpio {
> -	gpio-line-names =
> -		"", "", "", "", "", // 0 - 4
> -		"", "", "", "", "", // 5 - 9
> -		"UserButton", "", "", "", "", // 10 - 14
> -		"", "", "", "", "", // 15 - 19
> -		"", "", "", "", "", // 20 - 24
> -		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
> -		"Output1", "", "", "", "", // 30 - 34
> -		"", "ZigBeeBOOT", "", "", "", // 35 - 39
> -		"1Wire", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
> -		"Input2", "Input1", "", "", "", // 45 - 49
> -		"", "", "", "", "", // 50 - 54
> -		"", "", "", "", "", // 55 - 59
> -		"", "", "", "", "", // 60 - 64
> -		"", "", "", "", "", // 65 - 69
> -		"", "", "", "", "", // 70 - 74
> -		"", "", "", "", "", // 75 - 79
> -		"", "", "", "", "", // 80 - 84
> -		"", ""; // 85-86
> -};
> -
> -&cpu0 {
> -	#cooling-cells = <2>;
> -};
> -
> -&cpu1 {
> -	#cooling-cells = <2>;
> -};
> -
> -&cpu2 {
> -	#cooling-cells = <2>;
> -};
> -
> -&cpu3 {
> -	#cooling-cells = <2>;
> -};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts
> new file mode 100644
> index 000000000000..0062667c4f65
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts
> @@ -0,0 +1,37 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
> + * Copyright (c) 2022 JetHome
> + * Author: Vyacheslav Bocharov <adeep@lexina.in>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-axg-jethome-jethub-j1xx.dtsi"
> +
> +/ {
> +	compatible = "jethome,jethub-j110", "amlogic,a113d", "amlogic,meson-axg";
> +	model = "JetHome JetHub D1p (J110) HW rev.2";
> +
> +	/* 2GiB or 4GiB RAM */
> +	memory@0 {
> +		device_type = "memory";
> +		reg = <0x0 0x0 0x0 0x80000000>;
> +	};
> +};
> +
> +
> +/* wifi module */
> +&sd_emmc_b {
> +	broken-cd;/* cd-gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;*/
> +};
> +
> +/* UART Bluetooth */
> +&uart_B {
> +	bluetooth {
> +		compatible = "realtek,rtl8822cs-bt";
> +		enable-gpios  = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
> +		host-wake-gpios = <&gpio GPIOZ_8 GPIO_ACTIVE_HIGH>;
> +		device-wake-gpios = <&gpio GPIOZ_6 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts
> new file mode 100644
> index 000000000000..c2d22b00c1cd
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts
> @@ -0,0 +1,27 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
> + * Copyright (c) 2022 JetHome
> + * Author: Vyacheslav Bocharov <adeep@lexina.in>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-axg-jethome-jethub-j1xx.dtsi"
> +
> +/ {
> +	compatible = "jethome,jethub-j110", "amlogic,a113d", "amlogic,meson-axg";
> +	model = "JetHome JetHub D1p (J110) Hw rev.3";
> +
> +	/* 2GiB or 4GiB RAM */
> +	memory@0 {
> +		device_type = "memory";
> +		reg = <0x0 0x0 0x0 0x80000000>;
> +	};
> +};
> +
> +
> +/* wifi module */
> +&sd_emmc_b {
> +	broken-cd;/* cd-gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;*/
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi
> new file mode 100644
> index 000000000000..5836b0030931
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi
> @@ -0,0 +1,351 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
> + * Copyright (c) 2022 JetHome
> + * Author: Vyacheslav Bocharov <adeep@lexina.in>
> + * Author: Aleksandr Kazantsev <ak@tvip.ru>
> + * Author: Alexey Shevelkin <ash@tvip.ru>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-axg.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> +	aliases {
> +		serial0 = &uart_AO;   /* Console */
> +		serial2 = &uart_AO_B; /* External UART (Wireless Module) */
> +		ethernet0 = &ethmac;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	reserved-memory {
> +		linux,cma {
> +			size = <0x0 0x400000>;
> +		};
> +	};
> +
> +	emmc_pwrseq: emmc-pwrseq {
> +		compatible = "mmc-pwrseq-emmc";
> +		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	vcc_3v3: regulator-vcc_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	vcc_5v: regulator-vcc_5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +
> +	vddao_3v3: regulator-vddao_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDAO_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_5v>;
> +		regulator-always-on;
> +	};
> +
> +	vddio_ao18: regulator-vddio_ao18 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_AO18";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	vddio_boot: regulator-vddio_boot {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_BOOT";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	vccq_1v8: regulator-vccq_1v8 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCCQ_1V8";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	usb_pwr: regulator-usb_pwr {
> +		compatible = "regulator-fixed";
> +		regulator-name = "USB_PWR";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc_5v>;
> +		regulator-always-on;
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
> +		clocks = <&wifi32k>;
> +		clock-names = "ext_clock";
> +	};
> +
> +	wifi32k: wifi32k {
> +		compatible = "pwm-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
> +	};
> +
> +	thermal-zones {
> +		cpu_thermal: cpu-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&scpi_sensors 0>;
> +			trips {
> +				cpu_passive: cpu-passive {
> +					temperature = <70000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "passive";
> +				};
> +
> +				cpu_hot: cpu-hot {
> +					temperature = <80000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "hot";
> +				};
> +
> +				cpu_critical: cpu-critical {
> +					temperature = <100000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "critical";
> +				};
> +			};
> +
> +			cpu_cooling_maps: cooling-maps {
> +				map0 {
> +					trip = <&cpu_passive>;
> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +
> +				map1 {
> +					trip = <&cpu_hot>;
> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +	};
> +
> +	onewire {
> +		compatible = "w1-gpio";
> +		gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>;
> +		#gpio-cells = <1>;
> +	};
> +};
> +
> +&efuse {
> +	sn: sn@32 {
> +		reg = <0x32 0x20>;
> +	};
> +
> +	eth_mac: eth_mac@0 {
> +		reg = <0x0 0x6>;
> +	};
> +
> +	bt_mac: bt_mac@6 {
> +		reg = <0x6 0x6>;
> +	};
> +
> +	wifi_mac: wifi_mac@c {
> +		reg = <0xc 0x6>;
> +	};
> +
> +	bid: bid@12 {
> +		reg = <0x12 0x20>;
> +	};
> +};
> +
> +&ethmac {
> +	status = "okay";
> +	pinctrl-0 = <&eth_rmii_x_pins>;
> +	pinctrl-names = "default";
> +	phy-handle = <&eth_phy0>;
> +	phy-mode = "rmii";
> +
> +	mdio {
> +		compatible = "snps,dwmac-mdio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
> +		eth_phy0: ethernet-phy@0 {
> +			/* compatible = "ethernet-phy-id0243.0c54";*/
> +			max-speed = <100>;
> +			reg = <0>;
> +
> +			reset-assert-us = <10000>;
> +			reset-deassert-us = <10000>;
> +			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +};
> +
> +/* Internal I2C bus (on CPU module) */
> +&i2c1 {
> +	status = "okay";
> +	pinctrl-0 = <&i2c1_z_pins>;
> +	pinctrl-names = "default";
> +
> +	/* RTC */
> +	pcf8563: pcf8563@51 {
> +		compatible = "nxp,pcf8563";
> +		reg = <0x51>;
> +		status = "okay";
> +	};
> +};
> +
> +/* Peripheral I2C bus (on motherboard) */
> +&i2c_AO {
> +	status = "okay";
> +	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&pwm_ab {
> +	status = "okay";
> +	pinctrl-0 = <&pwm_a_x20_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +/* wifi module */
> +&sd_emmc_b {
> +	status = "okay";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	pinctrl-0 = <&sdio_pins>;
> +	pinctrl-1 = <&sdio_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <50000000>;
> +	disable-wp;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* emmc storage */
> +&sd_emmc_c {
> +	status = "okay";
> +	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> +	pinctrl-1 = <&emmc_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <8>;
> +	cap-mmc-highspeed;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	disable-wp;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +
> +	mmc-pwrseq = <&emmc_pwrseq>;
> +
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vccq_1v8>;
> +};
> +
> +/* UART Bluetooth */
> +&uart_B {
> +	status = "okay";
> +	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
> +	pinctrl-names = "default";
> +	uart-has-rtscts;
> +};
> +
> +/* UART Console */
> +&uart_AO {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +/* UART Wireless module */
> +&uart_AO_B {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_b_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&usb {
> +	status = "okay";
> +	phy-supply = <&usb_pwr>;
> +};
> +
> +&spicc1 {
> +	status = "okay";
> +	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&gpio {
> +	gpio-line-names =
> +		"", "", "", "", "", // 0 - 4
> +		"", "", "", "", "", // 5 - 9
> +		"UserButton", "", "", "", "", // 10 - 14
> +		"", "", "", "", "", // 15 - 19
> +		"", "", "", "", "", // 20 - 24
> +		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
> +		"Output1", "", "", "", "", // 30 - 34
> +		"", "ZigBeeBOOT", "", "", "", // 35 - 39
> +		"1Wire", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
> +		"Input2", "Input1", "", "", "", // 45 - 49
> +		"", "", "", "", "", // 50 - 54
> +		"", "", "", "", "", // 55 - 59
> +		"", "", "", "", "", // 60 - 64
> +		"", "", "", "", "", // 65 - 69
> +		"", "", "", "", "", // 70 - 74
> +		"", "", "", "", "", // 75 - 79
> +		"", "", "", "", "", // 80 - 84
> +		"", ""; // 85-86
> +};
> +
> +&cpu0 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu1 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu2 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu3 {
> +	#cooling-cells = <2>;
> +};

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH 0/2] arm64: meson: add support for JetHome JetHub D1p (j110)
  2022-08-11 10:31 [PATCH 0/2] arm64: meson: add support for JetHome JetHub D1p (j110) Vyacheslav Bocharov
  2022-08-11 10:31 ` [PATCH 1/2] arm64: dts: meson-axg: add support for " Vyacheslav Bocharov
  2022-08-11 10:31 ` [PATCH 2/2] dt-bindings: arm: amlogic: add bindings for Jethub " Vyacheslav Bocharov
@ 2022-08-16 12:22 ` Neil Armstrong
  2 siblings, 0 replies; 6+ messages in thread
From: Neil Armstrong @ 2022-08-16 12:22 UTC (permalink / raw)
  To: Vyacheslav Bocharov
  Cc: Neil Armstrong, Rob Herring, linux-arm-kernel, devicetree,
	linux-kernel, linux-amlogic

Hi,

On Thu, 11 Aug 2022 13:31:11 +0300, Vyacheslav Bocharov wrote:
> - add support for JetHome JetHub D1p (https://jethome.ru/d1p) is a home
> automation controller with the following features:
>   - DIN Rail Mounting
>   - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
>   - no video out
>   - 1/2/4GB LPDDR4
>   - 8/16/32GB eMMC flash
>   - 1 x USB 2.0
>   - 1 x 10/100Mbps ethernet
>   - WiFi / Bluetooth Realtek 8822CS or similar IEEE 802.11a/b/g/n/ac
>   - TI CC2652P1 Zigbee Wireless Module with up to 20dBm output power
>     and Zigbee 3.0 support.
>   - 2 x gpio LEDS
>   - GPIO user Button
>   - 1 x 1-Wire
>   - 2 x RS-485
>   - 4 x dry contact digital GPIO inputs
>   - 3 x relay GPIO outputs
>   - DC source with a voltage of 9 to 56 V / Active POE
> 
> [...]

Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v6.1/dt64)

[1/2] arm64: dts: meson-axg: add support for JetHub D1p (j110)
      https://git.kernel.org/amlogic/c/59ec069d50550273a83180ea6c950d382d7bf8e3
[2/2] dt-bindings: arm: amlogic: add bindings for Jethub D1p (j110)
      https://git.kernel.org/amlogic/c/a80c60359a42cf146872b9442cf847e7c2452a23

These changes has been applied on the intermediate git tree [1].

The v6.1/dt64 branch will then be sent via a formal Pull Request to the Linux SoC maintainers
for inclusion in their intermediate git branches in order to be sent to Linus during
the next merge window, or sooner if it's a set of fixes.

In the cases of fixes, those will be merged in the current release candidate
kernel and as soon they appear on the Linux master branch they will be
backported to the previous Stable and Long-Stable kernels [2].

The intermediate git branches are merged daily in the linux-next tree [3],
people are encouraged testing these pre-release kernels and report issues on the
relevant mailing-lists.

If problems are discovered on those changes, please submit a signed-off-by revert
patch followed by a corrective changeset.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
[3] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git

-- 
Neil

^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, other threads:[~2022-08-16 12:22 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-08-11 10:31 [PATCH 0/2] arm64: meson: add support for JetHome JetHub D1p (j110) Vyacheslav Bocharov
2022-08-11 10:31 ` [PATCH 1/2] arm64: dts: meson-axg: add support for " Vyacheslav Bocharov
2022-08-16  9:59   ` Neil Armstrong
2022-08-11 10:31 ` [PATCH 2/2] dt-bindings: arm: amlogic: add bindings for Jethub " Vyacheslav Bocharov
2022-08-14 21:26   ` Rob Herring
2022-08-16 12:22 ` [PATCH 0/2] arm64: meson: add support for JetHome JetHub " Neil Armstrong

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).