[PATCH v16 mfd 0/8] add support for VSC7512 control over SPI

[PATCH v16 mfd 0/8] add support for VSC7512 control over SPI

[Colin Foster]

The patch set in general is to add support for the VSC7512, and
eventually the VSC7511, VSC7513 and VSC7514 devices controlled over
SPI. Specifically this patch set enables pinctrl, serial gpio expander
access, and control of an internal and an external MDIO bus.

I have mentioned previously:
The hardware setup I'm using for development is a beaglebone black, with
jumpers from SPI0 to the microchip VSC7512 dev board. The microchip dev
board has been modified to not boot from flash, but wait for SPI. An
ethernet cable is connected from the beaglebone ethernet to port 0 of
the dev board. Network functionality will be included in a future patch set.

The device tree I'm using is included in the documentation, so I'll not
include that in this cover letter. I have exported the serial GPIOs to the
LEDs, and verified functionality via
"echo heartbeat > sys/class/leds/port0led/trigger"

/ {
	vscleds {
		compatible = "gpio-leds";
		vscled@0 {
			label = "port0led";
			gpios = <&sgpio_out1 0 0 GPIO_ACTIVE_LOW>;
			default-state = "off";
		};
		vscled@1 {
			label = "port0led1";
			gpios = <&sgpio_out1 0 1 GPIO_ACTIVE_LOW>;
			default-state = "off";
		};
[ ... ]
	};
};

I verified module functionality with modprobe ocelot-soc;
modprobe pinctrl-ocelot;
modprobe pinctrl-microchip-sgpio;

I only have hardware to test the last patch, so any testers are welcome.
I've been extra cautious about the ocelot_regmap_from_resource helper
function, both before and after the last patch. I accidentally broke it
in the past and would like to avoid doing so again.


RFC history:
v16
    * Add reviewed-by tags (patches 1-6)
    * Utilize resource_size() (patch 8/8)
    * One more round of missed includes (patch 8/8)
    * Remove pinctrl-ocelot module patch, which was applied in v6.0-rc1

v15
    * Add missed includes
    * Fix punctuation and function convention inside comments
    * Utilize spi_message_init_with_transfers() instead of
      spi_message_add_tail()
    * Remove unnecessary "< 0" comparisons
    * Utilize HZ_PER_MHZ instead of magic numbers

v14
    * Add header guards to include/linux/mfd/ocelot.h and
      drivers/mfd/ocelot.h
    * Lines extended to 100 chars (patch 9/9)
    * Remove unnecessary "dev" and "spi" elements from ocelot_ddata
      structure
    * Add doc comments for ocelot_ddata
    * Add Reviewed and Acked tags
    * Submit to MFD instead of net-next

v13
    * Suggestions from Andy for code cleanup, missed includes, forward
      declarations, module names.
    * Fix x86 allmodconfig build
    * MFD module name is now ocelot-soc
    * Add module names to Kconfig for pinctrl changes

v12
    * Suggestions from Vladimir, Andy, Randy, and Rob. Thanks as always!
    * Utilize dev_get_regmap to clean up interfaces
    * MFD_OCELOT can be a module

v11
    * Suggestions from Rob and Andy. Thanks!
    * Add pinctrl module functionality back and fixing those features
    * Fix aarch64 compiler error

v10
    * Fix warning by removing unused function

v9
    * Submitting as a PATCH instead of an RFC
    * Remove switch functionality - will be a separate patch set
    * Remove Kconfig tristate module options
    * Another round of suggestions from Lee, Vladimir, and Andy. Many
      thanks!
    * Add documentation
    * Update maintainers

v8
    * Applied another round of suggestions from Lee and Vladimir
    * Utilize regmap bus reads, which speeds bulk transfers up by an
      order of magnitude
    * Add two additional patches to utilize phylink_generic_validate
    * Changed GPL V2 to GPL in licenses where applicable (checkpatch)
    * Remove initial hsio/serdes changes from the RFC

v7
    * Applied as much as I could from Lee and Vladimir's suggestions. As
      always, the feedback is greatly appreciated!
    * Remove "ocelot_spi" container complication
    * Move internal MDIO bus from ocelot_ext to MFD, with a devicetree
      change to match
    * Add initial HSIO support
    * Switch to IORESOURCE_REG for resource definitions

v6
    * Applied several suggestions from the last RFC from Lee Jones. I
      hope I didn't miss anything.
    * Clean up MFD core - SPI interaction. They no longer use callbacks.
    * regmaps get registered to the child device, and don't attempt to
      get shared. It seems if a regmap is to be shared, that should be
      solved with syscon, not dev or mfd.

v5
    * Restructured to MFD
    * Several commits were split out, submitted, and accepted
    * pinctrl-ocelot believed to be fully functional (requires commits
    from the linux-pinctrl tree)
    * External MDIO bus believed to be fully functional

v4
    * Functional
    * Device tree fixes
    * Add hooks for pinctrl-ocelot - some functionality by way of sysfs
    * Add hooks for pinctrl-microsemi-sgpio - not yet fully functional
    * Remove lynx_pcs interface for a generic phylink_pcs. The goal here
    is to have an ocelot_pcs that will work for each configuration of
    every port.

v3
	* Functional
	* Shared MDIO transactions routed through mdio-mscc-miim
	* CPU / NPI port enabled by way of vsc7512_enable_npi_port /
	felix->info->enable_npi_port
	* NPI port tagging functional - Requires a CPU port driver that supports
	frames of 1520 bytes. Verified with a patch to the cpsw driver

v2
	* Near functional. No CPU port communication, but control over all
	external ports
	* Cleaned up regmap implementation from v1

v1 (accidentally named vN)
	* Initial architecture. Not functional
	* General concepts laid out

Colin Foster (8):
  mfd: ocelot: add helper to get regmap from a resource
  net: mdio: mscc-miim: add ability to be used in a non-mmio
    configuration
  pinctrl: ocelot: add ability to be used in a non-mmio configuration
  pinctrl: microchip-sgpio: allow sgpio driver to be used as a module
  pinctrl: microchip-sgpio: add ability to be used in a non-mmio
    configuration
  resource: add define macro for register address resources
  dt-bindings: mfd: ocelot: add bindings for VSC7512
  mfd: ocelot: add support for the vsc7512 chip via spi

 .../devicetree/bindings/mfd/mscc,ocelot.yaml  | 160 ++++++++++
 MAINTAINERS                                   |   7 +
 drivers/mfd/Kconfig                           |  21 ++
 drivers/mfd/Makefile                          |   3 +
 drivers/mfd/ocelot-core.c                     | 161 ++++++++++
 drivers/mfd/ocelot-spi.c                      | 299 ++++++++++++++++++
 drivers/mfd/ocelot.h                          |  49 +++
 drivers/net/mdio/mdio-mscc-miim.c             |  42 +--
 drivers/pinctrl/Kconfig                       |   5 +-
 drivers/pinctrl/pinctrl-microchip-sgpio.c     |  14 +-
 drivers/pinctrl/pinctrl-ocelot.c              |  16 +-
 include/linux/ioport.h                        |   5 +
 include/linux/mfd/ocelot.h                    |  62 ++++
 13 files changed, 795 insertions(+), 49 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/mscc,ocelot.yaml
 create mode 100644 drivers/mfd/ocelot-core.c
 create mode 100644 drivers/mfd/ocelot-spi.c
 create mode 100644 drivers/mfd/ocelot.h
 create mode 100644 include/linux/mfd/ocelot.h

-- 
2.25.1

[PATCH v16 mfd 1/8] mfd: ocelot: add helper to get regmap from a resource

[Colin Foster]

Several ocelot-related modules are designed for MMIO / regmaps. As such,
they often use a combination of devm_platform_get_and_ioremap_resource()
and devm_regmap_init_mmio().

Operating in an MFD might be different, in that it could be memory mapped,
or it could be SPI, I2C... In these cases a fallback to use IORESOURCE_REG
instead of IORESOURCE_MEM becomes necessary.

When this happens, there's redundant logic that needs to be implemented in
every driver. In order to avoid this redundancy, utilize a single function
that, if the MFD scenario is enabled, will perform this fallback logic.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
---
v16
    * Add Andy Reviewed-by tag

v15
    * Add missed errno.h and ioport.h includes
    * Add () to function references in both the commit log and comments

v14
    * Add header guard
    * Change regs type from u32* to void*
    * Add Reviewed-by tag

---
 MAINTAINERS                |  5 +++
 include/linux/mfd/ocelot.h | 62 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 67 insertions(+)
 create mode 100644 include/linux/mfd/ocelot.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 8a5012ba6ff9..e0732e9f9090 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14741,6 +14741,11 @@ F:	net/dsa/tag_ocelot.c
 F:	net/dsa/tag_ocelot_8021q.c
 F:	tools/testing/selftests/drivers/net/ocelot/*
 
+OCELOT EXTERNAL SWITCH CONTROL
+M:	Colin Foster <colin.foster@in-advantage.com>
+S:	Supported
+F:	include/linux/mfd/ocelot.h
+
 OCXL (Open Coherent Accelerator Processor Interface OpenCAPI) DRIVER
 M:	Frederic Barrat <fbarrat@linux.ibm.com>
 M:	Andrew Donnellan <ajd@linux.ibm.com>
diff --git a/include/linux/mfd/ocelot.h b/include/linux/mfd/ocelot.h
new file mode 100644
index 000000000000..dd72073d2d4f
--- /dev/null
+++ b/include/linux/mfd/ocelot.h
@@ -0,0 +1,62 @@
+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/* Copyright 2022 Innovative Advantage Inc. */
+
+#ifndef _LINUX_MFD_OCELOT_H
+#define _LINUX_MFD_OCELOT_H
+
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+struct resource;
+
+static inline struct regmap *
+ocelot_regmap_from_resource_optional(struct platform_device *pdev,
+				     unsigned int index,
+				     const struct regmap_config *config)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	void __iomem *regs;
+
+	/*
+	 * Don't use _get_and_ioremap_resource() here, since that will invoke
+	 * prints of "invalid resource" which will simply add confusion.
+	 */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, index);
+	if (res) {
+		regs = devm_ioremap_resource(dev, res);
+		if (IS_ERR(regs))
+			return ERR_CAST(regs);
+		return devm_regmap_init_mmio(dev, regs, config);
+	}
+
+	/*
+	 * Fall back to using REG and getting the resource from the parent
+	 * device, which is possible in an MFD configuration
+	 */
+	if (dev->parent) {
+		res = platform_get_resource(pdev, IORESOURCE_REG, index);
+		if (!res)
+			return NULL;
+
+		return dev_get_regmap(dev->parent, res->name);
+	}
+
+	return NULL;
+}
+
+static inline struct regmap *
+ocelot_regmap_from_resource(struct platform_device *pdev, unsigned int index,
+			    const struct regmap_config *config)
+{
+	struct regmap *map;
+
+	map = ocelot_regmap_from_resource_optional(pdev, index, config);
+	return map ?: ERR_PTR(-ENOENT);
+}
+
+#endif
-- 
2.25.1

[PATCH v16 mfd 2/8] net: mdio: mscc-miim: add ability to be used in a non-mmio configuration

[Colin Foster]

There are a few Ocelot chips that contain the logic for this bus, but are
controlled externally. Specifically the VSC7511, 7512, 7513, and 7514. In
the externally controlled configurations these registers are not
memory-mapped.

Add support for these non-memory-mapped configurations.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
---

v16
    * Add Andy Reviewed-by tag

v15
    * No changes

v14
    * Add Reviewed and Acked tags

---
 drivers/net/mdio/mdio-mscc-miim.c | 42 +++++++++----------------------
 1 file changed, 12 insertions(+), 30 deletions(-)

diff --git a/drivers/net/mdio/mdio-mscc-miim.c b/drivers/net/mdio/mdio-mscc-miim.c
index 08541007b18a..51f68daac152 100644
--- a/drivers/net/mdio/mdio-mscc-miim.c
+++ b/drivers/net/mdio/mdio-mscc-miim.c
@@ -12,6 +12,7 @@
 #include <linux/iopoll.h>
 #include <linux/kernel.h>
 #include <linux/mdio/mdio-mscc-miim.h>
+#include <linux/mfd/ocelot.h>
 #include <linux/module.h>
 #include <linux/of_mdio.h>
 #include <linux/phy.h>
@@ -270,44 +271,25 @@ static int mscc_miim_clk_set(struct mii_bus *bus)
 
 static int mscc_miim_probe(struct platform_device *pdev)
 {
-	struct regmap *mii_regmap, *phy_regmap = NULL;
 	struct device_node *np = pdev->dev.of_node;
+	struct regmap *mii_regmap, *phy_regmap;
 	struct device *dev = &pdev->dev;
-	void __iomem *regs, *phy_regs;
 	struct mscc_miim_dev *miim;
-	struct resource *res;
 	struct mii_bus *bus;
 	int ret;
 
-	regs = devm_platform_get_and_ioremap_resource(pdev, 0, NULL);
-	if (IS_ERR(regs)) {
-		dev_err(dev, "Unable to map MIIM registers\n");
-		return PTR_ERR(regs);
-	}
-
-	mii_regmap = devm_regmap_init_mmio(dev, regs, &mscc_miim_regmap_config);
-
-	if (IS_ERR(mii_regmap)) {
-		dev_err(dev, "Unable to create MIIM regmap\n");
-		return PTR_ERR(mii_regmap);
-	}
+	mii_regmap = ocelot_regmap_from_resource(pdev, 0,
+						 &mscc_miim_regmap_config);
+	if (IS_ERR(mii_regmap))
+		return dev_err_probe(dev, PTR_ERR(mii_regmap),
+				     "Unable to create MIIM regmap\n");
 
 	/* This resource is optional */
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	if (res) {
-		phy_regs = devm_ioremap_resource(dev, res);
-		if (IS_ERR(phy_regs)) {
-			dev_err(dev, "Unable to map internal phy registers\n");
-			return PTR_ERR(phy_regs);
-		}
-
-		phy_regmap = devm_regmap_init_mmio(dev, phy_regs,
-						   &mscc_miim_phy_regmap_config);
-		if (IS_ERR(phy_regmap)) {
-			dev_err(dev, "Unable to create phy register regmap\n");
-			return PTR_ERR(phy_regmap);
-		}
-	}
+	phy_regmap = ocelot_regmap_from_resource_optional(pdev, 1,
+						 &mscc_miim_phy_regmap_config);
+	if (IS_ERR(phy_regmap))
+		return dev_err_probe(dev, PTR_ERR(phy_regmap),
+				     "Unable to create phy register regmap\n");
 
 	ret = mscc_miim_setup(dev, &bus, "mscc_miim", mii_regmap, 0);
 	if (ret < 0) {
-- 
2.25.1

[PATCH v16 mfd 3/8] pinctrl: ocelot: add ability to be used in a non-mmio configuration

[Colin Foster]

There are a few Ocelot chips that contain pinctrl logic, but can be
controlled externally. Specifically the VSC7511, 7512, 7513 and 7514. In
the externally controlled configurations these registers are not
memory-mapped.

Add support for these non-memory-mapped configurations.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
---

v16
    * Add Andy Reviewed-by tag

v15
    * No changes

v14
    * Add Reviewed and Acked tags

---
 drivers/pinctrl/pinctrl-ocelot.c | 16 +++++-----------
 1 file changed, 5 insertions(+), 11 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-ocelot.c b/drivers/pinctrl/pinctrl-ocelot.c
index c5fd154990c8..340ca2373429 100644
--- a/drivers/pinctrl/pinctrl-ocelot.c
+++ b/drivers/pinctrl/pinctrl-ocelot.c
@@ -10,6 +10,7 @@
 #include <linux/gpio/driver.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
+#include <linux/mfd/ocelot.h>
 #include <linux/of_device.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
@@ -1975,7 +1976,6 @@ static int ocelot_pinctrl_probe(struct platform_device *pdev)
 	struct ocelot_pinctrl *info;
 	struct reset_control *reset;
 	struct regmap *pincfg;
-	void __iomem *base;
 	int ret;
 	struct regmap_config regmap_config = {
 		.reg_bits = 32,
@@ -2004,20 +2004,14 @@ static int ocelot_pinctrl_probe(struct platform_device *pdev)
 				     "Failed to get reset\n");
 	reset_control_reset(reset);
 
-	base = devm_ioremap_resource(dev,
-			platform_get_resource(pdev, IORESOURCE_MEM, 0));
-	if (IS_ERR(base))
-		return PTR_ERR(base);
-
 	info->stride = 1 + (info->desc->npins - 1) / 32;
 
 	regmap_config.max_register = OCELOT_GPIO_SD_MAP * info->stride + 15 * 4;
 
-	info->map = devm_regmap_init_mmio(dev, base, &regmap_config);
-	if (IS_ERR(info->map)) {
-		dev_err(dev, "Failed to create regmap\n");
-		return PTR_ERR(info->map);
-	}
+	info->map = ocelot_regmap_from_resource(pdev, 0, &regmap_config);
+	if (IS_ERR(info->map))
+		return dev_err_probe(dev, PTR_ERR(info->map),
+				     "Failed to create regmap\n");
 	dev_set_drvdata(dev, info->map);
 	info->dev = dev;
 
-- 
2.25.1

[PATCH v16 mfd 4/8] pinctrl: microchip-sgpio: allow sgpio driver to be used as a module

[Colin Foster]

As the commit message suggests, this simply adds the ability to select
SGPIO pinctrl as a module. This becomes more practical when the SGPIO
hardware exists on an external chip, controlled indirectly by I2C or SPI.
This commit enables that level of control.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
---

v16
    * Add Andy Reviewed-by tag

v14,15
    * No changes

---
 drivers/pinctrl/Kconfig                   | 5 ++++-
 drivers/pinctrl/pinctrl-microchip-sgpio.c | 6 +++++-
 2 files changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 1cf74b0c42e5..d768dcf75cf1 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -292,7 +292,7 @@ config PINCTRL_MCP23S08
 	  corresponding interrupt-controller.
 
 config PINCTRL_MICROCHIP_SGPIO
-	bool "Pinctrl driver for Microsemi/Microchip Serial GPIO"
+	tristate "Pinctrl driver for Microsemi/Microchip Serial GPIO"
 	depends on OF
 	depends on HAS_IOMEM
 	select GPIOLIB
@@ -310,6 +310,9 @@ config PINCTRL_MICROCHIP_SGPIO
 	  connect control signals from SFP modules and to act as an
 	  LED controller.
 
+	  If compiled as a module, the module name will be
+	  pinctrl-microchip-sgpio.
+
 config PINCTRL_OCELOT
 	tristate "Pinctrl driver for the Microsemi Ocelot and Jaguar2 SoCs"
 	depends on OF
diff --git a/drivers/pinctrl/pinctrl-microchip-sgpio.c b/drivers/pinctrl/pinctrl-microchip-sgpio.c
index 6f55bf7d5e05..e56074b7e659 100644
--- a/drivers/pinctrl/pinctrl-microchip-sgpio.c
+++ b/drivers/pinctrl/pinctrl-microchip-sgpio.c
@@ -999,6 +999,7 @@ static const struct of_device_id microchip_sgpio_gpio_of_match[] = {
 		/* sentinel */
 	}
 };
+MODULE_DEVICE_TABLE(of, microchip_sgpio_gpio_of_match);
 
 static struct platform_driver microchip_sgpio_pinctrl_driver = {
 	.driver = {
@@ -1008,4 +1009,7 @@ static struct platform_driver microchip_sgpio_pinctrl_driver = {
 	},
 	.probe = microchip_sgpio_probe,
 };
-builtin_platform_driver(microchip_sgpio_pinctrl_driver);
+module_platform_driver(microchip_sgpio_pinctrl_driver);
+
+MODULE_DESCRIPTION("Microchip SGPIO Pinctrl Driver");
+MODULE_LICENSE("GPL");
-- 
2.25.1

[PATCH v16 mfd 5/8] pinctrl: microchip-sgpio: add ability to be used in a non-mmio configuration

[Colin Foster]

There are a few Ocelot chips that can contain SGPIO logic, but can be
controlled externally. Specifically the VSC7511, 7512, 7513, and 7514. In
the externally controlled configurations these registers are not
memory-mapped.

Add support for these non-memory-mapped configurations.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
---

v16
    * Add Andy Reviewed-by tag

v15
    * No changes

v14
    * Add Reviewed and Acked tags

---
 drivers/pinctrl/pinctrl-microchip-sgpio.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-microchip-sgpio.c b/drivers/pinctrl/pinctrl-microchip-sgpio.c
index e56074b7e659..2b4167a09b3b 100644
--- a/drivers/pinctrl/pinctrl-microchip-sgpio.c
+++ b/drivers/pinctrl/pinctrl-microchip-sgpio.c
@@ -12,6 +12,7 @@
 #include <linux/clk.h>
 #include <linux/gpio/driver.h>
 #include <linux/io.h>
+#include <linux/mfd/ocelot.h>
 #include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/pinctrl/pinmux.h>
@@ -904,7 +905,6 @@ static int microchip_sgpio_probe(struct platform_device *pdev)
 	struct reset_control *reset;
 	struct sgpio_priv *priv;
 	struct clk *clk;
-	u32 __iomem *regs;
 	u32 val;
 	struct regmap_config regmap_config = {
 		.reg_bits = 32,
@@ -937,11 +937,7 @@ static int microchip_sgpio_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	regs = devm_platform_ioremap_resource(pdev, 0);
-	if (IS_ERR(regs))
-		return PTR_ERR(regs);
-
-	priv->regs = devm_regmap_init_mmio(dev, regs, &regmap_config);
+	priv->regs = ocelot_regmap_from_resource(pdev, 0, &regmap_config);
 	if (IS_ERR(priv->regs))
 		return PTR_ERR(priv->regs);
 
-- 
2.25.1

[PATCH v16 mfd 6/8] resource: add define macro for register address resources

[Colin Foster]

DEFINE_RES_ macros have been created for the commonly used resource types,
but not IORESOURCE_REG. Add the macro so it can be used in a similar manner
to all other resource types.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
---

v16
    * Add Andy Reviewed-by tag

v15
    * No changes

v14
    * Add Reviewed tag

---
 include/linux/ioport.h | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/include/linux/ioport.h b/include/linux/ioport.h
index 616b683563a9..8a76dca9deee 100644
--- a/include/linux/ioport.h
+++ b/include/linux/ioport.h
@@ -172,6 +172,11 @@ enum {
 #define DEFINE_RES_MEM(_start, _size)					\
 	DEFINE_RES_MEM_NAMED((_start), (_size), NULL)
 
+#define DEFINE_RES_REG_NAMED(_start, _size, _name)			\
+	DEFINE_RES_NAMED((_start), (_size), (_name), IORESOURCE_REG)
+#define DEFINE_RES_REG(_start, _size)					\
+	DEFINE_RES_REG_NAMED((_start), (_size), NULL)
+
 #define DEFINE_RES_IRQ_NAMED(_irq, _name)				\
 	DEFINE_RES_NAMED((_irq), 1, (_name), IORESOURCE_IRQ)
 #define DEFINE_RES_IRQ(_irq)						\
-- 
2.25.1

[PATCH v16 mfd 7/8] dt-bindings: mfd: ocelot: add bindings for VSC7512

[Colin Foster]

Add devicetree bindings for SPI-controlled Ocelot chips, specifically the
VSC7512.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---

(No changes since v14)

v14
    * Add Vladimir Reviewed tag

---
 .../devicetree/bindings/mfd/mscc,ocelot.yaml  | 160 ++++++++++++++++++
 MAINTAINERS                                   |   1 +
 2 files changed, 161 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/mscc,ocelot.yaml

diff --git a/Documentation/devicetree/bindings/mfd/mscc,ocelot.yaml b/Documentation/devicetree/bindings/mfd/mscc,ocelot.yaml
new file mode 100644
index 000000000000..8bf45a5673a4
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/mscc,ocelot.yaml
@@ -0,0 +1,160 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause */
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/mscc,ocelot.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ocelot Externally-Controlled Ethernet Switch
+
+maintainers:
+  - Colin Foster <colin.foster@in-advantage.com>
+
+description: |
+  The Ocelot ethernet switch family contains chips that have an internal CPU
+  (VSC7513, VSC7514) and chips that don't (VSC7511, VSC7512). All switches have
+  the option to be controlled externally, which is the purpose of this driver.
+
+  The switch family is a multi-port networking switch that supports many
+  interfaces. Additionally, the device can perform pin control, MDIO buses, and
+  external GPIO expanders.
+
+properties:
+  compatible:
+    enum:
+      - mscc,vsc7512
+
+  reg:
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 1
+
+  spi-max-frequency:
+    maxItems: 1
+
+patternProperties:
+  "^pinctrl@[0-9a-f]+$":
+    type: object
+    $ref: /schemas/pinctrl/mscc,ocelot-pinctrl.yaml
+
+  "^gpio@[0-9a-f]+$":
+    type: object
+    $ref: /schemas/pinctrl/microchip,sparx5-sgpio.yaml
+    properties:
+      compatible:
+        enum:
+          - mscc,ocelot-sgpio
+
+  "^mdio@[0-9a-f]+$":
+    type: object
+    $ref: /schemas/net/mscc,miim.yaml
+    properties:
+      compatible:
+        enum:
+          - mscc,ocelot-miim
+
+required:
+  - compatible
+  - reg
+  - '#address-cells'
+  - '#size-cells'
+  - spi-max-frequency
+
+additionalProperties: false
+
+examples:
+  - |
+    ocelot_clock: ocelot-clock {
+          compatible = "fixed-clock";
+          #clock-cells = <0>;
+          clock-frequency = <125000000>;
+      };
+
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        soc@0 {
+            compatible = "mscc,vsc7512";
+            spi-max-frequency = <2500000>;
+            reg = <0>;
+            #address-cells = <1>;
+            #size-cells = <1>;
+
+            mdio@7107009c {
+                compatible = "mscc,ocelot-miim";
+                #address-cells = <1>;
+                #size-cells = <0>;
+                reg = <0x7107009c 0x24>;
+
+                sw_phy0: ethernet-phy@0 {
+                    reg = <0x0>;
+                };
+            };
+
+            mdio@710700c0 {
+                compatible = "mscc,ocelot-miim";
+                pinctrl-names = "default";
+                pinctrl-0 = <&miim1_pins>;
+                #address-cells = <1>;
+                #size-cells = <0>;
+                reg = <0x710700c0 0x24>;
+
+                sw_phy4: ethernet-phy@4 {
+                    reg = <0x4>;
+                };
+            };
+
+            gpio: pinctrl@71070034 {
+                compatible = "mscc,ocelot-pinctrl";
+                gpio-controller;
+                #gpio-cells = <2>;
+                gpio-ranges = <&gpio 0 0 22>;
+                reg = <0x71070034 0x6c>;
+
+                sgpio_pins: sgpio-pins {
+                    pins = "GPIO_0", "GPIO_1", "GPIO_2", "GPIO_3";
+                    function = "sg0";
+                };
+
+                miim1_pins: miim1-pins {
+                    pins = "GPIO_14", "GPIO_15";
+                    function = "miim";
+                };
+            };
+
+            gpio@710700f8 {
+                compatible = "mscc,ocelot-sgpio";
+                #address-cells = <1>;
+                #size-cells = <0>;
+                bus-frequency = <12500000>;
+                clocks = <&ocelot_clock>;
+                microchip,sgpio-port-ranges = <0 15>;
+                pinctrl-names = "default";
+                pinctrl-0 = <&sgpio_pins>;
+                reg = <0x710700f8 0x100>;
+
+                sgpio_in0: gpio@0 {
+                    compatible = "microchip,sparx5-sgpio-bank";
+                    reg = <0>;
+                    gpio-controller;
+                    #gpio-cells = <3>;
+                    ngpios = <64>;
+                };
+
+                sgpio_out1: gpio@1 {
+                    compatible = "microchip,sparx5-sgpio-bank";
+                    reg = <1>;
+                    gpio-controller;
+                    #gpio-cells = <3>;
+                    ngpios = <64>;
+                };
+            };
+        };
+    };
+
+...
+
diff --git a/MAINTAINERS b/MAINTAINERS
index e0732e9f9090..a5df3b0b9601 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14744,6 +14744,7 @@ F:	tools/testing/selftests/drivers/net/ocelot/*
 OCELOT EXTERNAL SWITCH CONTROL
 M:	Colin Foster <colin.foster@in-advantage.com>
 S:	Supported
+F:	Documentation/devicetree/bindings/mfd/mscc,ocelot.yaml
 F:	include/linux/mfd/ocelot.h
 
 OCXL (Open Coherent Accelerator Processor Interface OpenCAPI) DRIVER
-- 
2.25.1

[PATCH v16 mfd 8/8] mfd: ocelot: add support for the vsc7512 chip via spi

[Colin Foster]

The VSC7512 is a networking chip that contains several peripherals. Many of
these peripherals are currently supported by the VSC7513 and VSC7514 chips,
but those run on an internal CPU. The VSC7512 lacks this CPU, and must be
controlled externally.

Utilize the existing drivers by referencing the chip as an MFD. Add support
for the two MDIO buses, the internal phys, pinctrl, and serial GPIO.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---

v16
    * Includes fixups:
    *  ocelot-core.c add includes device.h, export.h, iopoll.h, ioport,h
    *  ocelot-spi.c add includes device.h, err.h, errno.h, export.h, 
       mod_devicetable.h, types.h
    *  Move kconfig.h from ocelot-spi.c to ocelot.h
    *  Remove unnecessary byteorder.h
    * Utilize resource_size() function

v15
    * Add missed include bits.h
    * Clean _SIZE macros to make them all the same width (e.g. 0x004)
    * Remove unnecessary ret = ...; return ret; calls
    * Utilize spi_message_init_with_transfers() instead of
      spi_message_add_tail() calls in the bus_read routine
    * Utilize HZ_PER_MHZ from units.h instead of a magic number
    * Remove unnecessary err < 0 checks
    * Fix typos in comments

v14
    * Add Reviewed tag
    * Copyright ranges are now "2021-2022"
    * 100-char width applied instead of 80
    * Remove invalid dev_err_probe return
    * Remove "spi" and "dev" elements from ocelot_ddata struct.
    Since "dev" is available throughout, determine "ddata" and "spi" from
    there instead of keeping separate references.
    * Add header guard in drivers/mfd/ocelot.h
    * Document ocelot_ddata struct

---
 MAINTAINERS               |   1 +
 drivers/mfd/Kconfig       |  21 +++
 drivers/mfd/Makefile      |   3 +
 drivers/mfd/ocelot-core.c | 161 ++++++++++++++++++++
 drivers/mfd/ocelot-spi.c  | 299 ++++++++++++++++++++++++++++++++++++++
 drivers/mfd/ocelot.h      |  49 +++++++
 6 files changed, 534 insertions(+)
 create mode 100644 drivers/mfd/ocelot-core.c
 create mode 100644 drivers/mfd/ocelot-spi.c
 create mode 100644 drivers/mfd/ocelot.h

diff --git a/MAINTAINERS b/MAINTAINERS
index a5df3b0b9601..90a873dd04b0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14745,6 +14745,7 @@ OCELOT EXTERNAL SWITCH CONTROL
 M:	Colin Foster <colin.foster@in-advantage.com>
 S:	Supported
 F:	Documentation/devicetree/bindings/mfd/mscc,ocelot.yaml
+F:	drivers/mfd/ocelot*
 F:	include/linux/mfd/ocelot.h
 
 OCXL (Open Coherent Accelerator Processor Interface OpenCAPI) DRIVER
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index abb58ab1a1a4..c3dd1fe8d8c9 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -963,6 +963,27 @@ config MFD_MENF21BMC
 	  This driver can also be built as a module. If so the module
 	  will be called menf21bmc.
 
+config MFD_OCELOT
+	tristate "Microsemi Ocelot External Control Support"
+	depends on SPI_MASTER
+	select MFD_CORE
+	select REGMAP_SPI
+	help
+	  Ocelot is a family of networking chips that support multiple ethernet
+	  and fibre interfaces. In addition to networking, they contain several
+	  other functions, including pinctrl, MDIO, and communication with
+	  external chips. While some chips have an internal processor capable of
+	  running an OS, others don't. All chips can be controlled externally
+	  through different interfaces, including SPI, I2C, and PCIe.
+
+	  Say yes here to add support for Ocelot chips (VSC7511, VSC7512,
+	  VSC7513, VSC7514) controlled externally.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called ocelot-soc.
+
+	  If unsure, say N.
+
 config EZX_PCAP
 	bool "Motorola EZXPCAP Support"
 	depends on SPI_MASTER
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 858cacf659d6..0004b7e86220 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -120,6 +120,9 @@ obj-$(CONFIG_MFD_MC13XXX_I2C)	+= mc13xxx-i2c.o
 
 obj-$(CONFIG_MFD_CORE)		+= mfd-core.o
 
+ocelot-soc-objs			:= ocelot-core.o ocelot-spi.o
+obj-$(CONFIG_MFD_OCELOT)	+= ocelot-soc.o
+
 obj-$(CONFIG_EZX_PCAP)		+= ezx-pcap.o
 obj-$(CONFIG_MFD_CPCAP)		+= motorola-cpcap.o
 
diff --git a/drivers/mfd/ocelot-core.c b/drivers/mfd/ocelot-core.c
new file mode 100644
index 000000000000..1816d52c65c5
--- /dev/null
+++ b/drivers/mfd/ocelot-core.c
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Core driver for the Ocelot chip family.
+ *
+ * The VSC7511, 7512, 7513, and 7514 can be controlled internally via an
+ * on-chip MIPS processor, or externally via SPI, I2C, PCIe. This core driver is
+ * intended to be the bus-agnostic glue between, for example, the SPI bus and
+ * the child devices.
+ *
+ * Copyright 2021-2022 Innovative Advantage Inc.
+ *
+ * Author: Colin Foster <colin.foster@in-advantage.com>
+ */
+
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/export.h>
+#include <linux/iopoll.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/ocelot.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+#include <soc/mscc/ocelot.h>
+
+#include "ocelot.h"
+
+#define REG_GCB_SOFT_RST		0x0008
+
+#define BIT_SOFT_CHIP_RST		BIT(0)
+
+#define VSC7512_MIIM0_RES_START		0x7107009c
+#define VSC7512_MIIM1_RES_START		0x710700c0
+#define VSC7512_MIIM_RES_SIZE		0x024
+
+#define VSC7512_PHY_RES_START		0x710700f0
+#define VSC7512_PHY_RES_SIZE		0x004
+
+#define VSC7512_GPIO_RES_START		0x71070034
+#define VSC7512_GPIO_RES_SIZE		0x06c
+
+#define VSC7512_SIO_CTRL_RES_START	0x710700f8
+#define VSC7512_SIO_CTRL_RES_SIZE	0x100
+
+#define VSC7512_GCB_RST_SLEEP_US	100
+#define VSC7512_GCB_RST_TIMEOUT_US	100000
+
+static int ocelot_gcb_chip_rst_status(struct ocelot_ddata *ddata)
+{
+	int val, err;
+
+	err = regmap_read(ddata->gcb_regmap, REG_GCB_SOFT_RST, &val);
+	if (err)
+		return err;
+
+	return val;
+}
+
+int ocelot_chip_reset(struct device *dev)
+{
+	struct ocelot_ddata *ddata = dev_get_drvdata(dev);
+	int ret, val;
+
+	/*
+	 * Reset the entire chip here to put it into a completely known state.
+	 * Other drivers may want to reset their own subsystems. The register
+	 * self-clears, so one write is all that is needed and wait for it to
+	 * clear.
+	 */
+	ret = regmap_write(ddata->gcb_regmap, REG_GCB_SOFT_RST, BIT_SOFT_CHIP_RST);
+	if (ret)
+		return ret;
+
+	return readx_poll_timeout(ocelot_gcb_chip_rst_status, ddata, val, !val,
+				  VSC7512_GCB_RST_SLEEP_US, VSC7512_GCB_RST_TIMEOUT_US);
+}
+EXPORT_SYMBOL_NS(ocelot_chip_reset, MFD_OCELOT);
+
+static const struct resource vsc7512_miim0_resources[] = {
+	DEFINE_RES_REG_NAMED(VSC7512_MIIM0_RES_START, VSC7512_MIIM_RES_SIZE, "gcb_miim0"),
+	DEFINE_RES_REG_NAMED(VSC7512_PHY_RES_START, VSC7512_PHY_RES_SIZE, "gcb_phy"),
+};
+
+static const struct resource vsc7512_miim1_resources[] = {
+	DEFINE_RES_REG_NAMED(VSC7512_MIIM1_RES_START, VSC7512_MIIM_RES_SIZE, "gcb_miim1"),
+};
+
+static const struct resource vsc7512_pinctrl_resources[] = {
+	DEFINE_RES_REG_NAMED(VSC7512_GPIO_RES_START, VSC7512_GPIO_RES_SIZE, "gcb_gpio"),
+};
+
+static const struct resource vsc7512_sgpio_resources[] = {
+	DEFINE_RES_REG_NAMED(VSC7512_SIO_CTRL_RES_START, VSC7512_SIO_CTRL_RES_SIZE, "gcb_sio"),
+};
+
+static const struct mfd_cell vsc7512_devs[] = {
+	{
+		.name = "ocelot-pinctrl",
+		.of_compatible = "mscc,ocelot-pinctrl",
+		.num_resources = ARRAY_SIZE(vsc7512_pinctrl_resources),
+		.resources = vsc7512_pinctrl_resources,
+	}, {
+		.name = "ocelot-sgpio",
+		.of_compatible = "mscc,ocelot-sgpio",
+		.num_resources = ARRAY_SIZE(vsc7512_sgpio_resources),
+		.resources = vsc7512_sgpio_resources,
+	}, {
+		.name = "ocelot-miim0",
+		.of_compatible = "mscc,ocelot-miim",
+		.of_reg = VSC7512_MIIM0_RES_START,
+		.use_of_reg = true,
+		.num_resources = ARRAY_SIZE(vsc7512_miim0_resources),
+		.resources = vsc7512_miim0_resources,
+	}, {
+		.name = "ocelot-miim1",
+		.of_compatible = "mscc,ocelot-miim",
+		.of_reg = VSC7512_MIIM1_RES_START,
+		.use_of_reg = true,
+		.num_resources = ARRAY_SIZE(vsc7512_miim1_resources),
+		.resources = vsc7512_miim1_resources,
+	},
+};
+
+static void ocelot_core_try_add_regmap(struct device *dev,
+				       const struct resource *res)
+{
+	if (dev_get_regmap(dev, res->name))
+		return;
+
+	ocelot_spi_init_regmap(dev, res);
+}
+
+static void ocelot_core_try_add_regmaps(struct device *dev,
+					const struct mfd_cell *cell)
+{
+	int i;
+
+	for (i = 0; i < cell->num_resources; i++)
+		ocelot_core_try_add_regmap(dev, &cell->resources[i]);
+}
+
+int ocelot_core_init(struct device *dev)
+{
+	int i, ndevs;
+
+	ndevs = ARRAY_SIZE(vsc7512_devs);
+
+	for (i = 0; i < ndevs; i++)
+		ocelot_core_try_add_regmaps(dev, &vsc7512_devs[i]);
+
+	return devm_mfd_add_devices(dev, PLATFORM_DEVID_AUTO, vsc7512_devs, ndevs, NULL, 0, NULL);
+}
+EXPORT_SYMBOL_NS(ocelot_core_init, MFD_OCELOT);
+
+MODULE_DESCRIPTION("Externally Controlled Ocelot Chip Driver");
+MODULE_AUTHOR("Colin Foster <colin.foster@in-advantage.com>");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(MFD_OCELOT_SPI);
diff --git a/drivers/mfd/ocelot-spi.c b/drivers/mfd/ocelot-spi.c
new file mode 100644
index 000000000000..0f097f4829d1
--- /dev/null
+++ b/drivers/mfd/ocelot-spi.c
@@ -0,0 +1,299 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * SPI core driver for the Ocelot chip family.
+ *
+ * This driver will handle everything necessary to allow for communication over
+ * SPI to the VSC7511, VSC7512, VSC7513 and VSC7514 chips. The main functions
+ * are to prepare the chip's SPI interface for a specific bus speed, and a host
+ * processor's endianness. This will create and distribute regmaps for any
+ * children.
+ *
+ * Copyright 2021-2022 Innovative Advantage Inc.
+ *
+ * Author: Colin Foster <colin.foster@in-advantage.com>
+ */
+
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/export.h>
+#include <linux/ioport.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+#include <linux/types.h>
+#include <linux/units.h>
+
+#include "ocelot.h"
+
+#define REG_DEV_CPUORG_IF_CTRL		0x0000
+#define REG_DEV_CPUORG_IF_CFGSTAT	0x0004
+
+#define CFGSTAT_IF_NUM_VCORE		(0 << 24)
+#define CFGSTAT_IF_NUM_VRAP		(1 << 24)
+#define CFGSTAT_IF_NUM_SI		(2 << 24)
+#define CFGSTAT_IF_NUM_MIIM		(3 << 24)
+
+#define VSC7512_DEVCPU_ORG_RES_START	0x71000000
+#define VSC7512_DEVCPU_ORG_RES_SIZE	0x38
+
+#define VSC7512_CHIP_REGS_RES_START	0x71070000
+#define VSC7512_CHIP_REGS_RES_SIZE	0x14
+
+static const struct resource vsc7512_dev_cpuorg_resource =
+	DEFINE_RES_REG_NAMED(VSC7512_DEVCPU_ORG_RES_START,
+			     VSC7512_DEVCPU_ORG_RES_SIZE,
+			     "devcpu_org");
+
+static const struct resource vsc7512_gcb_resource =
+	DEFINE_RES_REG_NAMED(VSC7512_CHIP_REGS_RES_START,
+			     VSC7512_CHIP_REGS_RES_SIZE,
+			     "devcpu_gcb_chip_regs");
+
+static int ocelot_spi_initialize(struct device *dev)
+{
+	struct ocelot_ddata *ddata = dev_get_drvdata(dev);
+	u32 val, check;
+	int err;
+
+	val = OCELOT_SPI_BYTE_ORDER;
+
+	/*
+	 * The SPI address must be big-endian, but we want the payload to match
+	 * our CPU. These are two bits (0 and 1) but they're repeated such that
+	 * the write from any configuration will be valid. The four
+	 * configurations are:
+	 *
+	 * 0b00: little-endian, MSB first
+	 * |            111111   | 22221111 | 33222222 |
+	 * | 76543210 | 54321098 | 32109876 | 10987654 |
+	 *
+	 * 0b01: big-endian, MSB first
+	 * | 33222222 | 22221111 | 111111   |          |
+	 * | 10987654 | 32109876 | 54321098 | 76543210 |
+	 *
+	 * 0b10: little-endian, LSB first
+	 * |              111111 | 11112222 | 22222233 |
+	 * | 01234567 | 89012345 | 67890123 | 45678901 |
+	 *
+	 * 0b11: big-endian, LSB first
+	 * | 22222233 | 11112222 |   111111 |          |
+	 * | 45678901 | 67890123 | 89012345 | 01234567 |
+	 */
+	err = regmap_write(ddata->cpuorg_regmap, REG_DEV_CPUORG_IF_CTRL, val);
+	if (err)
+		return err;
+
+	/*
+	 * Apply the number of padding bytes between a read request and the data
+	 * payload. Some registers have access times of up to 1us, so if the
+	 * first payload bit is shifted out too quickly, the read will fail.
+	 */
+	val = ddata->spi_padding_bytes;
+	err = regmap_write(ddata->cpuorg_regmap, REG_DEV_CPUORG_IF_CFGSTAT, val);
+	if (err)
+		return err;
+
+	/*
+	 * After we write the interface configuration, read it back here. This
+	 * will verify several different things. The first is that the number of
+	 * padding bytes actually got written correctly. These are found in bits
+	 * 0:3.
+	 *
+	 * The second is that bit 16 is cleared. Bit 16 is IF_CFGSTAT:IF_STAT,
+	 * and will be set if the register access is too fast. This would be in
+	 * the condition that the number of padding bytes is insufficient for
+	 * the SPI bus frequency.
+	 *
+	 * The last check is for bits 31:24, which define the interface by which
+	 * the registers are being accessed. Since we're accessing them via the
+	 * serial interface, it must return IF_NUM_SI.
+	 */
+	check = val | CFGSTAT_IF_NUM_SI;
+
+	err = regmap_read(ddata->cpuorg_regmap, REG_DEV_CPUORG_IF_CFGSTAT, &val);
+	if (err)
+		return err;
+
+	if (check != val)
+		return -ENODEV;
+
+	return 0;
+}
+
+static const struct regmap_config ocelot_spi_regmap_config = {
+	.reg_bits = 24,
+	.reg_stride = 4,
+	.reg_downshift = 2,
+	.val_bits = 32,
+
+	.write_flag_mask = 0x80,
+
+	.use_single_write = true,
+	.can_multi_write = false,
+
+	.reg_format_endian = REGMAP_ENDIAN_BIG,
+	.val_format_endian = REGMAP_ENDIAN_NATIVE,
+};
+
+static int ocelot_spi_regmap_bus_read(void *context, const void *reg, size_t reg_size,
+				      void *val, size_t val_size)
+{
+	struct spi_transfer xfers[3] = {0};
+	struct device *dev = context;
+	struct ocelot_ddata *ddata;
+	struct spi_device *spi;
+	struct spi_message msg;
+	unsigned int index = 0;
+
+	ddata = dev_get_drvdata(dev);
+	spi = to_spi_device(dev);
+
+	xfers[index].tx_buf = reg;
+	xfers[index].len = reg_size;
+	index++;
+
+	if (ddata->spi_padding_bytes) {
+		xfers[index].len = ddata->spi_padding_bytes;
+		xfers[index].tx_buf = ddata->dummy_buf;
+		xfers[index].dummy_data = 1;
+		index++;
+	}
+
+	xfers[index].rx_buf = val;
+	xfers[index].len = val_size;
+	index++;
+
+	spi_message_init_with_transfers(&msg, xfers, index);
+
+	return spi_sync(spi, &msg);
+}
+
+static int ocelot_spi_regmap_bus_write(void *context, const void *data, size_t count)
+{
+	struct device *dev = context;
+	struct spi_device *spi = to_spi_device(dev);
+
+	return spi_write(spi, data, count);
+}
+
+static const struct regmap_bus ocelot_spi_regmap_bus = {
+	.write = ocelot_spi_regmap_bus_write,
+	.read = ocelot_spi_regmap_bus_read,
+};
+
+struct regmap *ocelot_spi_init_regmap(struct device *dev, const struct resource *res)
+{
+	struct regmap_config regmap_config;
+
+	memcpy(&regmap_config, &ocelot_spi_regmap_config, sizeof(regmap_config));
+
+	regmap_config.name = res->name;
+	regmap_config.max_register = resource_size(res) - 1;
+	regmap_config.reg_base = res->start;
+
+	return devm_regmap_init(dev, &ocelot_spi_regmap_bus, dev, &regmap_config);
+}
+EXPORT_SYMBOL_NS(ocelot_spi_init_regmap, MFD_OCELOT_SPI);
+
+static int ocelot_spi_probe(struct spi_device *spi)
+{
+	struct device *dev = &spi->dev;
+	struct ocelot_ddata *ddata;
+	struct regmap *r;
+	int err;
+
+	ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL);
+	if (!ddata)
+		return -ENOMEM;
+
+	spi_set_drvdata(spi, ddata);
+
+	if (spi->max_speed_hz <= 500000) {
+		ddata->spi_padding_bytes = 0;
+	} else {
+		/*
+		 * Calculation taken from the manual for IF_CFGSTAT:IF_CFG.
+		 * Register access time is 1us, so we need to configure and send
+		 * out enough padding bytes between the read request and data
+		 * transmission that lasts at least 1 microsecond.
+		 */
+		ddata->spi_padding_bytes = 1 + (spi->max_speed_hz / HZ_PER_MHZ + 2) / 8;
+
+		ddata->dummy_buf = devm_kzalloc(dev, ddata->spi_padding_bytes, GFP_KERNEL);
+		if (!ddata->dummy_buf)
+			return -ENOMEM;
+	}
+
+	spi->bits_per_word = 8;
+
+	err = spi_setup(spi);
+	if (err)
+		return dev_err_probe(&spi->dev, err, "Error performing SPI setup\n");
+
+	r = ocelot_spi_init_regmap(dev, &vsc7512_dev_cpuorg_resource);
+	if (IS_ERR(r))
+		return PTR_ERR(r);
+
+	ddata->cpuorg_regmap = r;
+
+	r = ocelot_spi_init_regmap(dev, &vsc7512_gcb_resource);
+	if (IS_ERR(r))
+		return PTR_ERR(r);
+
+	ddata->gcb_regmap = r;
+
+	/*
+	 * The chip must be set up for SPI before it gets initialized and reset.
+	 * This must be done before calling init, and after a chip reset is
+	 * performed.
+	 */
+	err = ocelot_spi_initialize(dev);
+	if (err)
+		return dev_err_probe(dev, err, "Error initializing SPI bus\n");
+
+	err = ocelot_chip_reset(dev);
+	if (err)
+		return dev_err_probe(dev, err, "Error resetting device\n");
+
+	/*
+	 * A chip reset will clear the SPI configuration, so it needs to be done
+	 * again before we can access any registers.
+	 */
+	err = ocelot_spi_initialize(dev);
+	if (err)
+		return dev_err_probe(dev, err, "Error initializing SPI bus after reset\n");
+
+	err = ocelot_core_init(dev);
+	if (err)
+		return dev_err_probe(dev, err, "Error initializing Ocelot core\n");
+
+	return 0;
+}
+
+static const struct spi_device_id ocelot_spi_ids[] = {
+	{ "vsc7512", 0 },
+	{ }
+};
+
+static const struct of_device_id ocelot_spi_of_match[] = {
+	{ .compatible = "mscc,vsc7512" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ocelot_spi_of_match);
+
+static struct spi_driver ocelot_spi_driver = {
+	.driver = {
+		.name = "ocelot-soc",
+		.of_match_table = ocelot_spi_of_match,
+	},
+	.id_table = ocelot_spi_ids,
+	.probe = ocelot_spi_probe,
+};
+module_spi_driver(ocelot_spi_driver);
+
+MODULE_DESCRIPTION("SPI Controlled Ocelot Chip Driver");
+MODULE_AUTHOR("Colin Foster <colin.foster@in-advantage.com>");
+MODULE_LICENSE("Dual MIT/GPL");
+MODULE_IMPORT_NS(MFD_OCELOT);
diff --git a/drivers/mfd/ocelot.h b/drivers/mfd/ocelot.h
new file mode 100644
index 000000000000..b8bc2f1486e2
--- /dev/null
+++ b/drivers/mfd/ocelot.h
@@ -0,0 +1,49 @@
+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/* Copyright 2021, 2022 Innovative Advantage Inc. */
+
+#ifndef _MFD_OCELOT_H
+#define _MFD_OCELOT_H
+
+#include <linux/kconfig.h>
+
+struct device;
+struct regmap;
+struct resource;
+
+/**
+ * struct ocelot_ddata - Private data for an external Ocelot chip
+ * @gcb_regmap:		General Configuration Block regmap. Used for
+ *			operations like chip reset.
+ * @cpuorg_regmap:	CPU Device Origin Block regmap. Used for operations
+ *			like SPI bus configuration.
+ * @spi_padding_bytes:	Number of padding bytes that must be thrown out before
+ *			read data gets returned. This is calculated during
+ *			initialization based on bus speed.
+ * @dummy_buf:		Zero-filled buffer of spi_padding_bytes size. The dummy
+ *			bytes that will be sent out between the address and
+ *			data of a SPI read operation.
+ */
+struct ocelot_ddata {
+	struct regmap *gcb_regmap;
+	struct regmap *cpuorg_regmap;
+	int spi_padding_bytes;
+	void *dummy_buf;
+};
+
+int ocelot_chip_reset(struct device *dev);
+int ocelot_core_init(struct device *dev);
+
+/* SPI-specific routines that won't be necessary for other interfaces */
+struct regmap *ocelot_spi_init_regmap(struct device *dev,
+				      const struct resource *res);
+
+#define OCELOT_SPI_BYTE_ORDER_LE 0x00000000
+#define OCELOT_SPI_BYTE_ORDER_BE 0x81818181
+
+#ifdef __LITTLE_ENDIAN
+#define OCELOT_SPI_BYTE_ORDER OCELOT_SPI_BYTE_ORDER_LE
+#else
+#define OCELOT_SPI_BYTE_ORDER OCELOT_SPI_BYTE_ORDER_BE
+#endif
+
+#endif
-- 
2.25.1

Re: [PATCH v16 mfd 8/8] mfd: ocelot: add support for the vsc7512 chip via spi

[Colin Foster]

Add Lee - My apologies, it seems like you got a new email address and I
didn't copy it on this series.

On Sun, Aug 14, 2022 at 05:55:53PM -0700, Colin Foster wrote:
> The VSC7512 is a networking chip that contains several peripherals. Many of
> these peripherals are currently supported by the VSC7513 and VSC7514 chips,
> but those run on an internal CPU. The VSC7512 lacks this CPU, and must be
> controlled externally.
> 
> Utilize the existing drivers by referencing the chip as an MFD. Add support
> for the two MDIO buses, the internal phys, pinctrl, and serial GPIO.
> 
> Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> ---
> 
> v16
>     * Includes fixups:
>     *  ocelot-core.c add includes device.h, export.h, iopoll.h, ioport,h
>     *  ocelot-spi.c add includes device.h, err.h, errno.h, export.h, 
>        mod_devicetable.h, types.h
>     *  Move kconfig.h from ocelot-spi.c to ocelot.h
>     *  Remove unnecessary byteorder.h

Something is going on that I don't fully understand with <asm/byteorder.h>.
I don't quite see how ocelot-core is throwing all sorts of errors in x86
builds now:

https://patchwork.hopto.org/static/nipa/667471/12942993/build_allmodconfig_warn/stderr

Snippet from there:

/home/nipa/nipa/tests/patch/build_32bit/build_32bit.sh: line 21: ccache gcc: command not found
../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
../arch/x86/include/asm/bitops.h:66:1: warning: unreplaced symbol 'return'
../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
../include/asm-generic/bitops/generic-non-atomic.h:29:9: warning: unreplaced symbol 'mask'
../include/asm-generic/bitops/generic-non-atomic.h:30:9: warning: unreplaced symbol 'p'
../include/asm-generic/bitops/generic-non-atomic.h:32:10: warning: unreplaced symbol 'p'
../include/asm-generic/bitops/generic-non-atomic.h:32:16: warning: unreplaced symbol 'mask'
../include/asm-generic/bitops/generic-non-atomic.h:27:1: warning: unreplaced symbol 'return'
../drivers/mfd/ocelot-spi.c: note: in included file (through ../arch/x86/include/asm/bitops.h, ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ...):
../include/asm-generic/bitops/instrumented-non-atomic.h:26:1: warning: unreplaced symbol 'return'


<asm/byteorder.h> was included in both drivers/mfd/ocelot-spi.c and
drivers/mfd/ocelot.h previously, though Andy pointed out there didn't
seem to be any users... and I didn't either. I'm sure there's something
I must be missing.

>     * Utilize resource_size() function
> 

Re: [PATCH v16 mfd 8/8] mfd: ocelot: add support for the vsc7512 chip via spi

[Ido Schimmel]

On Mon, Aug 15, 2022 at 07:19:13AM -0700, Colin Foster wrote:
> Something is going on that I don't fully understand with <asm/byteorder.h>.
> I don't quite see how ocelot-core is throwing all sorts of errors in x86
> builds now:
> 
> https://patchwork.hopto.org/static/nipa/667471/12942993/build_allmodconfig_warn/stderr
> 
> Snippet from there:
> 
> /home/nipa/nipa/tests/patch/build_32bit/build_32bit.sh: line 21: ccache gcc: command not found
> ../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
> ../arch/x86/include/asm/bitops.h:66:1: warning: unreplaced symbol 'return'
> ../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
> ../include/asm-generic/bitops/generic-non-atomic.h:29:9: warning: unreplaced symbol 'mask'
> ../include/asm-generic/bitops/generic-non-atomic.h:30:9: warning: unreplaced symbol 'p'
> ../include/asm-generic/bitops/generic-non-atomic.h:32:10: warning: unreplaced symbol 'p'
> ../include/asm-generic/bitops/generic-non-atomic.h:32:16: warning: unreplaced symbol 'mask'
> ../include/asm-generic/bitops/generic-non-atomic.h:27:1: warning: unreplaced symbol 'return'
> ../drivers/mfd/ocelot-spi.c: note: in included file (through ../arch/x86/include/asm/bitops.h, ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ...):
> ../include/asm-generic/bitops/instrumented-non-atomic.h:26:1: warning: unreplaced symbol 'return'
> 
> 
> <asm/byteorder.h> was included in both drivers/mfd/ocelot-spi.c and
> drivers/mfd/ocelot.h previously, though Andy pointed out there didn't
> seem to be any users... and I didn't either. I'm sure there's something
> I must be missing.

I got similar errors in our internal CI yesterday. Fixed by compiling
sparse from git:
https://git.kernel.org/pub/scm/devel/sparse/sparse.git/commit/?id=0e1aae55e49cad7ea43848af5b58ff0f57e7af99

The update is also available in the "testing" repo in case you are
running Fedora 35 / 36:
https://bodhi.fedoraproject.org/updates/FEDORA-2022-c58b53730f
https://bodhi.fedoraproject.org/updates/FEDORA-2022-2bc333ccac

Re: [PATCH v16 mfd 8/8] mfd: ocelot: add support for the vsc7512 chip via spi

[Colin Foster]

On Mon, Aug 15, 2022 at 05:35:12PM +0300, Ido Schimmel wrote:
> On Mon, Aug 15, 2022 at 07:19:13AM -0700, Colin Foster wrote:
> > Something is going on that I don't fully understand with <asm/byteorder.h>.
> > I don't quite see how ocelot-core is throwing all sorts of errors in x86
> > builds now:
> > 
> > https://patchwork.hopto.org/static/nipa/667471/12942993/build_allmodconfig_warn/stderr
> > 
> > Snippet from there:
> > 
> > /home/nipa/nipa/tests/patch/build_32bit/build_32bit.sh: line 21: ccache gcc: command not found
> > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
> > ../arch/x86/include/asm/bitops.h:66:1: warning: unreplaced symbol 'return'
> > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
> > ../include/asm-generic/bitops/generic-non-atomic.h:29:9: warning: unreplaced symbol 'mask'
> > ../include/asm-generic/bitops/generic-non-atomic.h:30:9: warning: unreplaced symbol 'p'
> > ../include/asm-generic/bitops/generic-non-atomic.h:32:10: warning: unreplaced symbol 'p'
> > ../include/asm-generic/bitops/generic-non-atomic.h:32:16: warning: unreplaced symbol 'mask'
> > ../include/asm-generic/bitops/generic-non-atomic.h:27:1: warning: unreplaced symbol 'return'
> > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../arch/x86/include/asm/bitops.h, ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ...):
> > ../include/asm-generic/bitops/instrumented-non-atomic.h:26:1: warning: unreplaced symbol 'return'
> > 
> > 
> > <asm/byteorder.h> was included in both drivers/mfd/ocelot-spi.c and
> > drivers/mfd/ocelot.h previously, though Andy pointed out there didn't
> > seem to be any users... and I didn't either. I'm sure there's something
> > I must be missing.
> 
> I got similar errors in our internal CI yesterday. Fixed by compiling
> sparse from git:
> https://git.kernel.org/pub/scm/devel/sparse/sparse.git/commit/?id=0e1aae55e49cad7ea43848af5b58ff0f57e7af99
> 
> The update is also available in the "testing" repo in case you are
> running Fedora 35 / 36:
> https://bodhi.fedoraproject.org/updates/FEDORA-2022-c58b53730f
> https://bodhi.fedoraproject.org/updates/FEDORA-2022-2bc333ccac

Thanks for the info! I haven't been able to fully recreate the issue
locally, those are from kernel test robot. I'll give this a shot if I
run into it locally though.

Re: [PATCH v16 mfd 8/8] mfd: ocelot: add support for the vsc7512 chip via spi

[Andy Shevchenko]

On Mon, Aug 15, 2022 at 5:35 PM Ido Schimmel <idosch@idosch.org> wrote:
>
> On Mon, Aug 15, 2022 at 07:19:13AM -0700, Colin Foster wrote:
> > Something is going on that I don't fully understand with <asm/byteorder.h>.
> > I don't quite see how ocelot-core is throwing all sorts of errors in x86
> > builds now:
> >
> > https://patchwork.hopto.org/static/nipa/667471/12942993/build_allmodconfig_warn/stderr
> >
> > Snippet from there:
> >
> > /home/nipa/nipa/tests/patch/build_32bit/build_32bit.sh: line 21: ccache gcc: command not found
> > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
> > ../arch/x86/include/asm/bitops.h:66:1: warning: unreplaced symbol 'return'
> > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
> > ../include/asm-generic/bitops/generic-non-atomic.h:29:9: warning: unreplaced symbol 'mask'
> > ../include/asm-generic/bitops/generic-non-atomic.h:30:9: warning: unreplaced symbol 'p'
> > ../include/asm-generic/bitops/generic-non-atomic.h:32:10: warning: unreplaced symbol 'p'
> > ../include/asm-generic/bitops/generic-non-atomic.h:32:16: warning: unreplaced symbol 'mask'
> > ../include/asm-generic/bitops/generic-non-atomic.h:27:1: warning: unreplaced symbol 'return'
> > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../arch/x86/include/asm/bitops.h, ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ...):
> > ../include/asm-generic/bitops/instrumented-non-atomic.h:26:1: warning: unreplaced symbol 'return'
> >
> >
> > <asm/byteorder.h> was included in both drivers/mfd/ocelot-spi.c and
> > drivers/mfd/ocelot.h previously, though Andy pointed out there didn't
> > seem to be any users... and I didn't either. I'm sure there's something
> > I must be missing.
>
> I got similar errors in our internal CI yesterday. Fixed by compiling
> sparse from git:
> https://git.kernel.org/pub/scm/devel/sparse/sparse.git/commit/?id=0e1aae55e49cad7ea43848af5b58ff0f57e7af99
>
> The update is also available in the "testing" repo in case you are
> running Fedora 35 / 36:
> https://bodhi.fedoraproject.org/updates/FEDORA-2022-c58b53730f
> https://bodhi.fedoraproject.org/updates/FEDORA-2022-2bc333ccac

Debian still produces the same errors which makes sparse useless.

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v16 mfd 8/8] mfd: ocelot: add support for the vsc7512 chip via spi

[Colin Foster]

On Tue, Aug 16, 2022 at 11:52:53AM +0300, Andy Shevchenko wrote:
> On Mon, Aug 15, 2022 at 5:35 PM Ido Schimmel <idosch@idosch.org> wrote:
> >
> > On Mon, Aug 15, 2022 at 07:19:13AM -0700, Colin Foster wrote:
> > > Something is going on that I don't fully understand with <asm/byteorder.h>.
> > > I don't quite see how ocelot-core is throwing all sorts of errors in x86
> > > builds now:
> > >
> > > https://patchwork.hopto.org/static/nipa/667471/12942993/build_allmodconfig_warn/stderr
> > >
> > > Snippet from there:
> > >
> > > /home/nipa/nipa/tests/patch/build_32bit/build_32bit.sh: line 21: ccache gcc: command not found
> > > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
> > > ../arch/x86/include/asm/bitops.h:66:1: warning: unreplaced symbol 'return'
> > > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
> > > ../include/asm-generic/bitops/generic-non-atomic.h:29:9: warning: unreplaced symbol 'mask'
> > > ../include/asm-generic/bitops/generic-non-atomic.h:30:9: warning: unreplaced symbol 'p'
> > > ../include/asm-generic/bitops/generic-non-atomic.h:32:10: warning: unreplaced symbol 'p'
> > > ../include/asm-generic/bitops/generic-non-atomic.h:32:16: warning: unreplaced symbol 'mask'
> > > ../include/asm-generic/bitops/generic-non-atomic.h:27:1: warning: unreplaced symbol 'return'
> > > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../arch/x86/include/asm/bitops.h, ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ...):
> > > ../include/asm-generic/bitops/instrumented-non-atomic.h:26:1: warning: unreplaced symbol 'return'
> > >
> > >
> > > <asm/byteorder.h> was included in both drivers/mfd/ocelot-spi.c and
> > > drivers/mfd/ocelot.h previously, though Andy pointed out there didn't
> > > seem to be any users... and I didn't either. I'm sure there's something
> > > I must be missing.
> >
> > I got similar errors in our internal CI yesterday. Fixed by compiling
> > sparse from git:
> > https://git.kernel.org/pub/scm/devel/sparse/sparse.git/commit/?id=0e1aae55e49cad7ea43848af5b58ff0f57e7af99
> >
> > The update is also available in the "testing" repo in case you are
> > running Fedora 35 / 36:
> > https://bodhi.fedoraproject.org/updates/FEDORA-2022-c58b53730f
> > https://bodhi.fedoraproject.org/updates/FEDORA-2022-2bc333ccac
> 
> Debian still produces the same errors which makes sparse useless.

I haven't jumped into this one yet. But everything seems to be compiling
and running in ARM.

Do you think this is a false positive / unrelated to this patch? Or do
you think this is a true error that I did wrong? I haven't been around
for too many releases, so I'm not sure if this is common after an -rc1.

> 
> -- 
> With Best Regards,
> Andy Shevchenko

Re: [PATCH v16 mfd 8/8] mfd: ocelot: add support for the vsc7512 chip via spi

[Andy Shevchenko]

On Tue, Aug 16, 2022 at 6:20 PM Colin Foster
<colin.foster@in-advantage.com> wrote:
>
> On Tue, Aug 16, 2022 at 11:52:53AM +0300, Andy Shevchenko wrote:
> > On Mon, Aug 15, 2022 at 5:35 PM Ido Schimmel <idosch@idosch.org> wrote:
> > >
> > > On Mon, Aug 15, 2022 at 07:19:13AM -0700, Colin Foster wrote:
> > > > Something is going on that I don't fully understand with <asm/byteorder.h>.
> > > > I don't quite see how ocelot-core is throwing all sorts of errors in x86
> > > > builds now:
> > > >
> > > > https://patchwork.hopto.org/static/nipa/667471/12942993/build_allmodconfig_warn/stderr
> > > >
> > > > Snippet from there:
> > > >
> > > > /home/nipa/nipa/tests/patch/build_32bit/build_32bit.sh: line 21: ccache gcc: command not found
> > > > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
> > > > ../arch/x86/include/asm/bitops.h:66:1: warning: unreplaced symbol 'return'
> > > > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ../include/linux/sched.h, ...):
> > > > ../include/asm-generic/bitops/generic-non-atomic.h:29:9: warning: unreplaced symbol 'mask'
> > > > ../include/asm-generic/bitops/generic-non-atomic.h:30:9: warning: unreplaced symbol 'p'
> > > > ../include/asm-generic/bitops/generic-non-atomic.h:32:10: warning: unreplaced symbol 'p'
> > > > ../include/asm-generic/bitops/generic-non-atomic.h:32:16: warning: unreplaced symbol 'mask'
> > > > ../include/asm-generic/bitops/generic-non-atomic.h:27:1: warning: unreplaced symbol 'return'
> > > > ../drivers/mfd/ocelot-spi.c: note: in included file (through ../arch/x86/include/asm/bitops.h, ../include/linux/bitops.h, ../include/linux/kernel.h, ../arch/x86/include/asm/percpu.h, ../arch/x86/include/asm/current.h, ...):
> > > > ../include/asm-generic/bitops/instrumented-non-atomic.h:26:1: warning: unreplaced symbol 'return'
> > > >
> > > >
> > > > <asm/byteorder.h> was included in both drivers/mfd/ocelot-spi.c and
> > > > drivers/mfd/ocelot.h previously, though Andy pointed out there didn't
> > > > seem to be any users... and I didn't either. I'm sure there's something
> > > > I must be missing.
> > >
> > > I got similar errors in our internal CI yesterday. Fixed by compiling
> > > sparse from git:
> > > https://git.kernel.org/pub/scm/devel/sparse/sparse.git/commit/?id=0e1aae55e49cad7ea43848af5b58ff0f57e7af99
> > >
> > > The update is also available in the "testing" repo in case you are
> > > running Fedora 35 / 36:
> > > https://bodhi.fedoraproject.org/updates/FEDORA-2022-c58b53730f
> > > https://bodhi.fedoraproject.org/updates/FEDORA-2022-2bc333ccac
> >
> > Debian still produces the same errors which makes sparse useless.
>
> I haven't jumped into this one yet. But everything seems to be compiling
> and running in ARM.
>
> Do you think this is a false positive / unrelated to this patch? Or do
> you think this is a true error that I did wrong? I haven't been around
> for too many releases, so I'm not sure if this is common after an -rc1.

It's a sparse issue and Debian maintainer for sparse is not updating
it for some reasons...

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v16 mfd 8/8] mfd: ocelot: add support for the vsc7512 chip via spi

[Colin Foster]

On Thu, Aug 18, 2022 at 10:26:12PM +0300, Andy Shevchenko wrote:
> On Tue, Aug 16, 2022 at 6:20 PM Colin Foster
> <colin.foster@in-advantage.com> wrote:
> >
> > Do you think this is a false positive / unrelated to this patch? Or do
> > you think this is a true error that I did wrong? I haven't been around
> > for too many releases, so I'm not sure if this is common after an -rc1.
> 
> It's a sparse issue and Debian maintainer for sparse is not updating
> it for some reasons...

K. I'll ignore for now and plan to re-submit next week (with Lee's
correct email address) unless I hear otherwise.

Thanks!

> 
> -- 
> With Best Regards,
> Andy Shevchenko