[PATCH v2] dt-bindings: power: reset: restart-handler: add common schema

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

Add common schema for restart and shutdown handlers, so they all use
same meaning of "priority" field.  The Linux drivers already have this
property and some systems want to customize it per-board in DTS.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

---

Changes since v1:
1. Use double ':'

v1 was marked as changes-requested in Rob's patchwork, but I think there
was not actual consensus on any other changes to make.

v1:
https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20220907123630.57383-1-krzysztof.kozlowski@linaro.org/

See also:
https://lore.kernel.org/all/8fe93da3-f768-16ae-7025-1cfa97a42b27@linaro.org/
https://lore.kernel.org/all/20220831081715.14673-1-pali@kernel.org/
---
 .../bindings/power/reset/gpio-restart.yaml    | 13 ++------
 .../bindings/power/reset/restart-handler.yaml | 30 +++++++++++++++++++
 2 files changed, 33 insertions(+), 10 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power/reset/restart-handler.yaml

diff --git a/Documentation/devicetree/bindings/power/reset/gpio-restart.yaml b/Documentation/devicetree/bindings/power/reset/gpio-restart.yaml
index a72d5c721516..d3d18e0f5db3 100644
--- a/Documentation/devicetree/bindings/power/reset/gpio-restart.yaml
+++ b/Documentation/devicetree/bindings/power/reset/gpio-restart.yaml
@@ -25,6 +25,9 @@ description: >
   inactive-delay, the GPIO is driven active again.  After a delay specified by wait-delay, the
   restart handler completes allowing other restart handlers to be attempted.
 
+allOf:
+  - $ref: restart-handler.yaml#
+
 properties:
   compatible:
     const: gpio-restart
@@ -41,16 +44,6 @@ properties:
       in its inactive state.
 
   priority:
-    $ref: /schemas/types.yaml#/definitions/uint32
-    description: |
-      A priority ranging from 0 to 255 (default 129) according to the following guidelines:
-
-        0:   Restart handler of last resort, with limited restart capabilities.
-        128: Default restart handler; use if no other restart handler is expected to be available,
-             and/or if restart functionality is sufficient to restart the entire system.
-        255: Highest priority restart handler, will preempt all other restart handlers.
-    minimum: 0
-    maximum: 255
     default: 129
 
   active-delay:
diff --git a/Documentation/devicetree/bindings/power/reset/restart-handler.yaml b/Documentation/devicetree/bindings/power/reset/restart-handler.yaml
new file mode 100644
index 000000000000..1f9a2aac53c0
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/restart-handler.yaml
@@ -0,0 +1,30 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/reset/restart-handler.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Restart and shutdown handler generic binding
+
+maintainers:
+  - Sebastian Reichel <sre@kernel.org>
+
+description:
+  Restart and shutdown handler device is responsible for powering off the
+  system, e.g. my cutting off the power.  System might have several restart
+  handlers, which usually are tried from most precise to last resort.
+
+properties:
+  priority:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      A priority ranging from 0 to 255 according to the following guidelines::
+        0::   Restart handler of last resort, with limited restart capabilities.
+        128:: Typical, default restart handler; use if no other restart handler
+              is expected to be available, and/or if restart functionality is
+              sufficient to restart the entire system.
+        255:: Highest priority restart handler, will preempt all other restart handlers.
+    minimum: 0
+    maximum: 255
+
+additionalProperties: true
-- 
2.34.1