From: Abel Vesa <abel.vesa@linaro.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Linus Walleij <linus.walleij@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
"linux-gpio@vger.kernel.org" <linux-gpio@vger.kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Subject: [PATCH v4 1/2] dt-bindings: pinctrl: qcom: Add SM8550 pinctrl
Date: Fri, 30 Dec 2022 22:36:36 +0200 [thread overview]
Message-ID: <20221230203637.2539900-2-abel.vesa@linaro.org> (raw)
In-Reply-To: <20221230203637.2539900-1-abel.vesa@linaro.org>
Add device tree binding Documentation details for Qualcomm SM8550
TLMM device
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../bindings/pinctrl/qcom,sm8550-tlmm.yaml | 163 ++++++++++++++++++
1 file changed, 163 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sm8550-tlmm.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8550-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8550-tlmm.yaml
new file mode 100644
index 000000000000..a457425ba112
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8550-tlmm.yaml
@@ -0,0 +1,163 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,sm8550-tlmm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. SM8550 TLMM block
+
+maintainers:
+ - Abel Vesa <abel.vesa@linaro.org>
+
+description:
+ Top Level Mode Multiplexer pin controller in Qualcomm SM8550 SoC.
+
+allOf:
+ - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+properties:
+ compatible:
+ const: qcom,sm8550-tlmm
+
+ reg:
+ maxItems: 1
+
+ interrupts: true
+ interrupt-controller: true
+ "#interrupt-cells": true
+ gpio-controller: true
+
+ gpio-reserved-ranges:
+ minItems: 1
+ maxItems: 105
+
+ gpio-line-names:
+ maxItems: 210
+
+ "#gpio-cells": true
+ gpio-ranges: true
+ wakeup-parent: true
+
+patternProperties:
+ "-state$":
+ oneOf:
+ - $ref: "#/$defs/qcom-sm8550-tlmm-state"
+ - patternProperties:
+ "-pins$":
+ $ref: "#/$defs/qcom-sm8550-tlmm-state"
+ additionalProperties: false
+
+$defs:
+ qcom-sm8550-tlmm-state:
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+
+ properties:
+ pins:
+ description:
+ List of gpio pins affected by the properties specified in this
+ subnode.
+ items:
+ oneOf:
+ - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-9][0-9]|20[0-9])$"
+ - enum: [ ufs_reset, sdc2_clk, sdc2_cmd, sdc2_data ]
+ minItems: 1
+ maxItems: 36
+
+ function:
+ description:
+ Specify the alternative function to be configured for the specified
+ pins.
+ enum: [ aon_cci, aoss_cti, atest_char, atest_usb,
+ audio_ext_mclk0, audio_ext_mclk1, audio_ref_clk,
+ cam_aon_mclk4, cam_mclk, cci_async_in, cci_i2c_scl,
+ cci_i2c_sda, cci_timer, cmu_rng, coex_uart1_rx,
+ coex_uart1_tx, coex_uart2_rx, coex_uart2_tx,
+ cri_trng, dbg_out_clk, ddr_bist_complete,
+ ddr_bist_fail, ddr_bist_start, ddr_bist_stop,
+ ddr_pxi0, ddr_pxi1, ddr_pxi2, ddr_pxi3, dp_hot,
+ gcc_gp1, gcc_gp2, gcc_gp3, gpio, i2chub0_se0,
+ i2chub0_se1, i2chub0_se2, i2chub0_se3, i2chub0_se4,
+ i2chub0_se5, i2chub0_se6, i2chub0_se7, i2chub0_se8,
+ i2chub0_se9, i2s0_data0, i2s0_data1, i2s0_sck,
+ i2s0_ws, i2s1_data0, i2s1_data1, i2s1_sck, i2s1_ws,
+ ibi_i3c, jitter_bist, mdp_vsync, mdp_vsync0_out,
+ mdp_vsync1_out, mdp_vsync2_out, mdp_vsync3_out,
+ mdp_vsync_e, nav_gpio0, nav_gpio1, nav_gpio2,
+ pcie0_clk_req_n, pcie1_clk_req_n, phase_flag,
+ pll_bist_sync, pll_clk_aux, prng_rosc0, prng_rosc1,
+ prng_rosc2, prng_rosc3, qdss_cti, qdss_gpio,
+ qlink0_enable, qlink0_request, qlink0_wmss,
+ qlink1_enable, qlink1_request, qlink1_wmss,
+ qlink2_enable, qlink2_request, qlink2_wmss,
+ qspi0, qspi1, qspi2, qspi3, qspi_clk, qspi_cs,
+ qup1_se0, qup1_se1, qup1_se2, qup1_se3, qup1_se4,
+ qup1_se5, qup1_se6, qup1_se7, qup2_se0,
+ qup2_se0_l0_mira, qup2_se0_l0_mirb, qup2_se0_l1_mira,
+ qup2_se0_l1_mirb, qup2_se0_l2_mira, qup2_se0_l2_mirb,
+ qup2_se0_l3_mira, qup2_se0_l3_mirb, qup2_se1,
+ qup2_se2, qup2_se3, qup2_se4, qup2_se5, qup2_se6,
+ qup2_se7, sd_write_protect, sdc40, sdc41, sdc42,
+ sdc43, sdc4_clk, sdc4_cmd, tb_trig_sdc2, tb_trig_sdc4,
+ tgu_ch0_trigout, tgu_ch1_trigout, tgu_ch2_trigout,
+ tgu_ch3_trigout, tmess_prng0, tmess_prng1, tmess_prng2,
+ tmess_prng3, tsense_pwm1, tsense_pwm2, tsense_pwm3,
+ uim0_clk, uim0_data, uim0_present, uim0_reset,
+ uim1_clk, uim1_data, uim1_present, uim1_reset,
+ usb1_hs, usb_phy, vfr_0, vfr_1, vsense_trigger_mirnat ]
+
+ bias-disable: true
+ bias-pull-down: true
+ bias-pull-up: true
+ drive-strength: true
+ input-enable: true
+ output-high: true
+ output-low: true
+
+ required:
+ - pins
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ tlmm: pinctrl@f100000 {
+ compatible = "qcom,sm8550-tlmm";
+ reg = <0x0f100000 0x300000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 211>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+ gpio-wo-state {
+ pins = "gpio1";
+ function = "gpio";
+ };
+
+ uart-w-state {
+ rx-pins {
+ pins = "gpio26";
+ function = "qup2_se7";
+ bias-pull-up;
+ };
+
+ tx-pins {
+ pins = "gpio27";
+ function = "qup2_se7";
+ bias-disable;
+ };
+ };
+ };
+...
--
2.34.1
next prev parent reply other threads:[~2022-12-30 20:38 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-12-30 20:36 [PATCH v4 0/2] pinctrl: qcom: Add support for SM8550 Abel Vesa
2022-12-30 20:36 ` Abel Vesa [this message]
2023-01-09 13:20 ` [PATCH v4 1/2] dt-bindings: pinctrl: qcom: Add SM8550 pinctrl Linus Walleij
2022-12-30 20:36 ` [PATCH v4 2/2] pinctrl: qcom: Add SM8550 pinctrl driver Abel Vesa
2023-01-09 13:21 ` Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221230203637.2539900-2-abel.vesa@linaro.org \
--to=abel.vesa@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).