linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Konrad Dybcio <konrad.dybcio@linaro.org>
To: linux-arm-msm@vger.kernel.org, andersson@kernel.org,
	agross@kernel.org, krzysztof.kozlowski@linaro.org
Cc: marijn.suijten@somainline.org,
	Konrad Dybcio <konrad.dybcio@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH] arm64: dts: qcom: msm8998-yoshino: Use SONY GPIO names
Date: Mon,  2 Jan 2023 20:01:57 +0100	[thread overview]
Message-ID: <20230102190157.970053-1-konrad.dybcio@linaro.org> (raw)

Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).

Add these to the Yoshino devices DTs to better document the hardware and
rename already-defined GPIO nodes to fit the "official" names.
Note that 4k_ is replaced with four_k_ in one pin, as labels can't start
with numbers.

Lilac and Poplar have identical pin assignments.

Diff between these two and maple:

TLMM:
-  "NC",
+  "TS_VDDIO_EN",

PMI8998:
-  "NC"
+  "USB_SWITCH_SEL"

-  "NC"
+  "4K_DISP_DCDC_EN"

PM8005:
-  "NC"
+  "EAR_EN"

Which is probably due to Maple being designed and released quite a bit
earlier than the other two and it having a super high tech true-4K
display.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 .../msm8998-sony-xperia-yoshino-maple.dts     | 179 +++++++++++-
 .../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 260 +++++++++++++++---
 2 files changed, 406 insertions(+), 33 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
index 20fe0394a3c1..e813b41f6db8 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
@@ -22,7 +22,7 @@ disp_dvdd_vreg: disp-dvdd-vreg {
 		enable-active-high;
 		gpio = <&pmi8998_gpio 10 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&disp_dvdd_en>;
+		pinctrl-0 = <&four_k_disp_dcdc_en>;
 	};
 };
 
@@ -37,8 +37,30 @@ &lab {
 	qcom,soft-start-us = <200>;
 };
 
+&pm8005_gpio {
+	gpio-line-names = "EAR_EN", /* GPIO_1 */
+			  "NC",
+			  "SLB",
+			  "OPTION_1_PM8005";
+};
+
 &pmi8998_gpio {
-	disp_dvdd_en: disp-dvdd-en-active-state {
+	gpio-line-names = "MAIN_CAM_PWR_IO_EN", /* GPIO_1 */
+			  "NC",
+			  "NC",
+			  "TYPEC_UUSB_SEL",
+			  "VIB_LDO_EN",
+			  "NC",
+			  "DISPLAY_TYPE_SEL",
+			  "USB_SWITCH_SEL",
+			  "NC",
+			  "4K_DISP_DCDC_EN", /* GPIO_10 */
+			  "NC",
+			  "DIV_CLK3",
+			  "SPMI_I2C_SEL",
+			  "NC";
+
+	four_k_disp_dcdc_en: 4k-disp-dcdc-en-state {
 		pins = "gpio10";
 		function = "normal";
 		bias-disable;
@@ -49,6 +71,159 @@ disp_dvdd_en: disp-dvdd-en-active-state {
 	};
 };
 
+&tlmm {
+	gpio-line-names = "", /* GPIO_0 */
+			  "",
+			  "",
+			  "",
+			  "DEBUG_UART_TX",
+			  "DEBUG_UART_RX",
+			  "CAMSENSOR_I2C_SDA",
+			  "CAMSENSOR_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "MDP_VSYNC_P", /* GPIO_10 */
+			  "RGBC_IR_INT",
+			  "NFC_VEN",
+			  "CAM_MCLK0",
+			  "CAM_MCLK1",
+			  "NC",
+			  "NC",
+			  "CCI_I2C_SDA0",
+			  "CCI_I2C_SCL0",
+			  "CCI_I2C_SDA1",
+			  "CCI_I2C_SCL1", /* GPIO_20 */
+			  "MAIN_CAM_PWR_EN",
+			  "TOF_INT_N",
+			  "NC",
+			  "NC",
+			  "CHAT_CAM_PWR_EN",
+			  "NC",
+			  "TOF_RESET_N",
+			  "CAM2_RSTN",
+			  "NC",
+			  "CAM1_RSTN", /* GPIO_30 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "CC_DIR",
+			  "UIM2_DETECT_EN",
+			  "FP_RESET_N", /* GPIO_40 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "BT_HCI_UART_TXD",
+			  "BT_HCI_UART_RXD",
+			  "BT_HCI_UART_CTS_N",
+			  "BT_HCI_UART_RFR_N",
+			  "NC",
+			  "NC", /* GPIO_50 */
+			  "NC",
+			  "NC",
+			  "CODEC_INT2_N",
+			  "CODEC_INT1_N",
+			  "APPS_I2C_SDA",
+			  "APPS_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_60 */
+			  "NC",
+			  "NC",
+			  "TRAY2_DET_DS",
+			  "CODEC_RST_N",
+			  "WSA_L_EN",
+			  "WSA_R_EN",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "LPASS_SLIMBUS_CLK", /* GPIO_70 */
+			  "LPASS_SLIMBUS_DATA0",
+			  "LPASS_SLIMBUS_DATA1",
+			  "BT_FM_SLIMBUS_DATA",
+			  "BT_FM_SLIMBUS_CLK",
+			  "NC",
+			  "RF_LCD_ID_EN",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_80 */
+			  "SW_SERVICE",
+			  "TX_GTR_THRES_IN",
+			  "HW_ID0",
+			  "HW_ID1",
+			  "NC",
+			  "NC",
+			  "TS_I2C_SDA",
+			  "TS_I2C_SCL",
+			  "TS_RESET_N",
+			  "NC", /* GPIO_90 */
+			  "NC",
+			  "NFC_IRQ",
+			  "NFC_DWLD_EN",
+			  "DISP_RESET_N",
+			  "TRAY2_DET",
+			  "CAM_SOF",
+			  "RFFE6_CLK",
+			  "RFFE6_DATA",
+			  "DEBUG_GPIO0",
+			  "DEBUG_GPIO1", /* GPIO_100 */
+			  "GRFC4",
+			  "NC",
+			  "NC",
+			  "RSVD",
+			  "UIM2_DATA",
+			  "UIM2_CLK",
+			  "UIM2_RESET",
+			  "UIM2_PRESENT",
+			  "UIM1_DATA",
+			  "UIM1_CLK", /* GPIO_110 */
+			  "UIM1_RST",
+			  "UIM1_PRESENT",
+			  "UIM_BATT_ALARM",
+			  "RSVD",
+			  "NC",
+			  "NC",
+			  "ACCEL_INT",
+			  "GYRO_INT",
+			  "COMPASS_INT",
+			  "ALS_PROX_INT_N", /* GPIO_120 */
+			  "FP_INT_N",
+			  "NC",
+			  "BAROMETER_INT",
+			  "ACC_COVER_OPEN",
+			  "TS_INT_N",
+			  "NC",
+			  "NC",
+			  "USB_DETECT_EN",
+			  "NC",
+			  "QLINK_REQUEST", /* GPIO_130 */
+			  "QLINK_ENABLE",
+			  "NC",
+			  "TS_VDDIO_EN",
+			  "WMSS_RESET_N",
+			  "PA_INDICATOR_OR",
+			  "NC",
+			  "RFFE3_DATA",
+			  "RFFE3_CLK",
+			  "RFFE4_DATA",
+			  "RFFE4_CLK", /* GPIO_140 */
+			  "RFFE5_DATA",
+			  "RFFE5_CLK",
+			  "GNSS_EN",
+			  "MSS_LTE_COXM_TXD",
+			  "MSS_LTE_COXM_RXD",
+			  "RFFE2_DATA",
+			  "RFFE2_CLK",
+			  "RFFE1_DATA",
+			  "RFFE1_CLK";
+};
+
 &vreg_l22a_2p85 {
 	regulator-min-microvolt = <2704000>;
 	regulator-max-microvolt = <2704000>;
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index 5da87baa2b23..a083361a7bc4 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -21,7 +21,7 @@ / {
 	clocks {
 		div1_mclk: divclk1 {
 			compatible = "gpio-gate-clock";
-			pinctrl-0 = <&audio_mclk_pin>;
+			pinctrl-0 = <&div_clk1>;
 			pinctrl-names = "default";
 			clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
 			#clock-cells = <0>;
@@ -46,7 +46,7 @@ cam0_vdig_vreg: cam0-vdig {
 		enable-active-high;
 		gpio = <&tlmm 21 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&cam0_vdig_default>;
+		pinctrl-0 = <&main_cam_pwr_en>;
 	};
 
 	cam1_vdig_vreg: cam1-vdig {
@@ -56,7 +56,7 @@ cam1_vdig_vreg: cam1-vdig {
 		enable-active-high;
 		gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&cam1_vdig_default>;
+		pinctrl-0 = <&chat_cam_pwr_en>;
 		vin-supply = <&vreg_s3a_1p35>;
 	};
 
@@ -67,7 +67,7 @@ cam_vio_vreg: cam-vio-vreg {
 		enable-active-high;
 		gpio = <&pmi8998_gpio 1 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&cam_vio_default>;
+		pinctrl-0 = <&main_cam_pwr_io_en>;
 		vin-supply = <&vreg_lvs1a_1p8>;
 	};
 
@@ -92,15 +92,14 @@ extcon_usb: extcon-usb {
 		id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>;
 		vbus-gpio = <&tlmm 128 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&usb_extcon_active &usb_vbus_active>;
+		pinctrl-0 = <&cc_dir_default &usb_detect_en>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 		label = "Side buttons";
 		pinctrl-names = "default";
-		pinctrl-0 = <&vol_down_pin_a>, <&cam_focus_pin_a>,
-			    <&cam_snapshot_pin_a>;
+		pinctrl-0 = <&vol_down_n &focus_n &snapshot_n>;
 		button-vol-down {
 			label = "Volume Down";
 			gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
@@ -131,7 +130,7 @@ gpio-hall-sensor {
 		compatible = "gpio-keys";
 		label = "Hall sensors";
 		pinctrl-names = "default";
-		pinctrl-0 = <&hall_sensor0_default>;
+		pinctrl-0 = <&acc_cover_open>;
 
 		event-hall-sensor0 {
 			label = "Cover Hall Sensor";
@@ -189,7 +188,7 @@ vibrator {
 		compatible = "gpio-vibrator";
 		enable-gpios = <&pmi8998_gpio 5 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&vib_default>;
+		pinctrl-0 = <&vib_ldo_en>;
 	};
 };
 
@@ -263,7 +262,7 @@ proximity@29 {
 		vdd-supply = <&cam_vio_vreg>;
 
 		pinctrl-names = "default";
-		pinctrl-0 = <&tof_int &tof_reset>;
+		pinctrl-0 = <&tof_int_n &tof_reset>;
 	};
 };
 
@@ -292,6 +291,13 @@ &lab {
 	regulator-soft-start;
 };
 
+&pm8005_gpio {
+	gpio-line-names = "NC", /* GPIO_1 */
+			  "NC",
+			  "SLB",
+			  "OPTION_1_PM8005";
+};
+
 &pm8005_regulators {
 	/* VDD_GFX supply */
 	pm8005_s1: s1 {
@@ -304,7 +310,34 @@ pm8005_s1: s1 {
 };
 
 &pm8998_gpio {
-	vol_down_pin_a: vol-down-active-state {
+	gpio-line-names = "UIM_BATT_ALARM", /* GPIO_1 */
+			  "NC",
+			  "WLAN_SW_CTRL (DISALLOWED)",
+			  "SSC_PWR_EN",
+			  "VOL_DOWN_N",
+			  "VOL_UP_N",
+			  "SNAPSHOT_N",
+			  "FOCUS_N",
+			  "FLASH_THERM",
+			  "", /* GPIO_10 */
+			  "",
+			  "",
+			  "DIV_CLK1",
+			  "NC",
+			  "NC (DISALLOWED)",
+			  "DIV_CLK3",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC (DISALLOWED)", /* GPIO_20 */
+			  "NFC_CLK_REQ",
+			  "NC (DISALLOWED)",
+			  "WCSS_PWR_REQ",
+			  "OPTION_1 (DISALLOWED)",
+			  "OPTION_2 (DISALLOWED)",
+			  "PM_SLB (DISALLOWED)";
+
+	vol_down_n: vol-down-n-state {
 		pins = "gpio5";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-pull-up;
@@ -312,7 +345,7 @@ vol_down_pin_a: vol-down-active-state {
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 
-	cam_focus_pin_a: cam-focus-btn-active-state {
+	focus_n: focus-n-state {
 		pins = "gpio7";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-pull-up;
@@ -320,7 +353,7 @@ cam_focus_pin_a: cam-focus-btn-active-state {
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 
-	cam_snapshot_pin_a: cam-snapshot-btn-active-state {
+	snapshot_n: snapshot-n-state {
 		pins = "gpio8";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-pull-up;
@@ -328,7 +361,7 @@ cam_snapshot_pin_a: cam-snapshot-btn-active-state {
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 
-	audio_mclk_pin: audio-mclk-pin-active-state {
+	div_clk1: div-clk1-state {
 		pins = "gpio13";
 		function = "func2";
 		power-source = <0>;
@@ -336,7 +369,22 @@ audio_mclk_pin: audio-mclk-pin-active-state {
 };
 
 &pmi8998_gpio {
-	cam_vio_default: cam-vio-active-state {
+	gpio-line-names = "MAIN_CAM_PWR_IO_EN", /* GPIO_1 */
+			  "NC",
+			  "NC",
+			  "TYPEC_UUSB_SEL",
+			  "VIB_LDO_EN",
+			  "NC",
+			  "DISPLAY_TYPE_SEL",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_10 */
+			  "NC",
+			  "DIV_CLK3",
+			  "SPMI_I2C_SEL",
+			  "NC";
+
+	main_cam_pwr_io_en: main-cam-pwr-io-en-state {
 		pins = "gpio1";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-disable;
@@ -346,7 +394,7 @@ cam_vio_default: cam-vio-active-state {
 		power-source = <1>;
 	};
 
-	vib_default: vib-en-state {
+	vib_ldo_en: vib-ldo-en-state {
 		pins = "gpio5";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-disable;
@@ -595,8 +643,158 @@ &sdhc2 {
 
 &tlmm {
 	gpio-reserved-ranges = <0 4>, <81 4>;
-
-	mdp_vsync_n: mdp-vsync-n-state {
+	gpio-line-names = "", /* GPIO_0 */
+			  "",
+			  "",
+			  "",
+			  "DEBUG_UART_TX",
+			  "DEBUG_UART_RX",
+			  "CAMSENSOR_I2C_SDA",
+			  "CAMSENSOR_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "MDP_VSYNC_P", /* GPIO_10 */
+			  "RGBC_IR_INT",
+			  "NFC_VEN",
+			  "CAM_MCLK0",
+			  "CAM_MCLK1",
+			  "NC",
+			  "NC",
+			  "CCI_I2C_SDA0",
+			  "CCI_I2C_SCL0",
+			  "CCI_I2C_SDA1",
+			  "CCI_I2C_SCL1", /* GPIO_20 */
+			  "MAIN_CAM_PWR_EN",
+			  "TOF_INT_N",
+			  "NC",
+			  "NC",
+			  "CHAT_CAM_PWR_EN",
+			  "NC",
+			  "TOF_RESET_N",
+			  "CAM2_RSTN",
+			  "NC",
+			  "CAM1_RSTN", /* GPIO_30 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "CC_DIR",
+			  "UIM2_DETECT_EN",
+			  "FP_RESET_N", /* GPIO_40 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "BT_HCI_UART_TXD",
+			  "BT_HCI_UART_RXD",
+			  "BT_HCI_UART_CTS_N",
+			  "BT_HCI_UART_RFR_N",
+			  "NC",
+			  "NC", /* GPIO_50 */
+			  "NC",
+			  "NC",
+			  "CODEC_INT2_N",
+			  "CODEC_INT1_N",
+			  "APPS_I2C_SDA",
+			  "APPS_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_60 */
+			  "NC",
+			  "NC",
+			  "TRAY2_DET_DS",
+			  "CODEC_RST_N",
+			  "WSA_L_EN",
+			  "WSA_R_EN",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "LPASS_SLIMBUS_CLK", /* GPIO_70 */
+			  "LPASS_SLIMBUS_DATA0",
+			  "LPASS_SLIMBUS_DATA1",
+			  "BT_FM_SLIMBUS_DATA",
+			  "BT_FM_SLIMBUS_CLK",
+			  "NC",
+			  "RF_LCD_ID_EN",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_80 */
+			  "SW_SERVICE",
+			  "TX_GTR_THRES_IN",
+			  "HW_ID0",
+			  "HW_ID1",
+			  "NC",
+			  "NC",
+			  "TS_I2C_SDA",
+			  "TS_I2C_SCL",
+			  "TS_RESET_N",
+			  "NC", /* GPIO_90 */
+			  "NC",
+			  "NFC_IRQ",
+			  "NFC_DWLD_EN",
+			  "DISP_RESET_N",
+			  "TRAY2_DET",
+			  "CAM_SOF",
+			  "RFFE6_CLK",
+			  "RFFE6_DATA",
+			  "DEBUG_GPIO0",
+			  "DEBUG_GPIO1", /* GPIO_100 */
+			  "GRFC4",
+			  "NC",
+			  "NC",
+			  "RSVD",
+			  "UIM2_DATA",
+			  "UIM2_CLK",
+			  "UIM2_RESET",
+			  "UIM2_PRESENT",
+			  "UIM1_DATA",
+			  "UIM1_CLK", /* GPIO_110 */
+			  "UIM1_RST",
+			  "UIM1_PRESENT",
+			  "UIM_BATT_ALARM",
+			  "RSVD",
+			  "NC",
+			  "NC",
+			  "ACCEL_INT",
+			  "GYRO_INT",
+			  "COMPASS_INT",
+			  "ALS_PROX_INT_N", /* GPIO_120 */
+			  "FP_INT_N",
+			  "NC",
+			  "BAROMETER_INT",
+			  "ACC_COVER_OPEN",
+			  "TS_INT_N",
+			  "NC",
+			  "NC",
+			  "USB_DETECT_EN",
+			  "NC",
+			  "QLINK_REQUEST", /* GPIO_130 */
+			  "QLINK_ENABLE",
+			  "NC",
+			  "NC",
+			  "WMSS_RESET_N",
+			  "PA_INDICATOR_OR",
+			  "NC",
+			  "RFFE3_DATA",
+			  "RFFE3_CLK",
+			  "RFFE4_DATA",
+			  "RFFE4_CLK", /* GPIO_140 */
+			  "RFFE5_DATA",
+			  "RFFE5_CLK",
+			  "GNSS_EN",
+			  "MSS_LTE_COXM_TXD",
+			  "MSS_LTE_COXM_RXD",
+			  "RFFE2_DATA",
+			  "RFFE2_CLK",
+			  "RFFE1_DATA",
+			  "RFFE1_CLK";
+
+	mdp_vsync_p: mdp-vsync-p-state {
 		pins = "gpio10";
 		function = "mdp_vsync_a";
 		drive-strength = <2>;
@@ -611,14 +809,14 @@ nfc_ven: nfc-ven-state {
 		output-low;
 	};
 
-	msm_mclk0_default: msm-mclk0-active-state {
+	cam_mclk0_active: cam-mclk0-active-state {
 		pins = "gpio13";
 		function = "cam_mclk";
 		drive-strength = <2>;
 		bias-disable;
 	};
 
-	msm_mclk1_default: msm-mclk1-active-state {
+	cam_mclk1_active: cam-mclk1-active-state {
 		pins = "gpio14";
 		function = "cam_mclk";
 		drive-strength = <2>;
@@ -639,14 +837,14 @@ cci1_default: cci1-default-state {
 		drive-strength = <2>;
 	};
 
-	cam0_vdig_default: cam0-vdig-default-state {
+	main_cam_pwr_en: main-cam-pwr-en-default-state {
 		pins = "gpio21";
 		function = "gpio";
 		bias-disable;
 		drive-strength = <2>;
 	};
 
-	tof_int: tof-int-state {
+	tof_int_n: tof-int-n-state {
 		pins = "gpio22";
 		function = "gpio";
 		bias-pull-up;
@@ -654,28 +852,28 @@ tof_int: tof-int-state {
 		input-enable;
 	};
 
-	cam1_vdig_default: cam1-vdig-default-state {
+	chat_cam_pwr_en: chat-cam-pwr-en-default-state {
 		pins = "gpio25";
 		function = "gpio";
 		bias-disable;
 		drive-strength = <2>;
 	};
 
-	usb_extcon_active: usb-extcon-active-state {
-		pins = "gpio38";
+	tof_reset: tof-reset-state {
+		pins = "gpio27";
 		function = "gpio";
 		bias-disable;
-		drive-strength = <16>;
+		drive-strength = <2>;
 	};
 
-	tof_reset: tof-reset-state {
-		pins = "gpio27";
+	cc_dir_default: cc-dir-active-state {
+		pins = "gpio38";
 		function = "gpio";
 		bias-disable;
-		drive-strength = <2>;
+		drive-strength = <16>;
 	};
 
-	hall_sensor0_default: acc-cover-open-state {
+	acc_cover_open: acc-cover-open-state {
 		pins = "gpio124";
 		function = "gpio";
 		bias-disable;
@@ -690,7 +888,7 @@ ts_int_n: ts-int-n-state {
 		bias-pull-up;
 	};
 
-	usb_vbus_active: usb-vbus-active-state {
+	usb_detect_en: usb-detect-en-active-state {
 		pins = "gpio128";
 		function = "gpio";
 		bias-disable;
-- 
2.39.0


             reply	other threads:[~2023-01-02 19:02 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-01-02 19:01 Konrad Dybcio [this message]
2023-01-03  1:07 ` [PATCH] arm64: dts: qcom: msm8998-yoshino: Use SONY GPIO names Dmitry Baryshkov

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230102190157.970053-1-konrad.dybcio@linaro.org \
    --to=konrad.dybcio@linaro.org \
    --cc=agross@kernel.org \
    --cc=andersson@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=krzysztof.kozlowski@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=marijn.suijten@somainline.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).