linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Frank Wunderlich <linux@fw-web.de>
To: linux-mediatek@lists.infradead.org
Cc: Frank Wunderlich <frank-w@public-files.de>,
	Chunfeng Yun <chunfeng.yun@mediatek.com>,
	Vinod Koul <vkoul@kernel.org>,
	Kishon Vijay Abraham I <kishon@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Matthias Brugger <matthias.bgg@gmail.com>,
	linux-arm-kernel@lists.infradead.org,
	linux-phy@lists.infradead.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, Sam Shih <sam.shih@mediatek.com>
Subject: [PATCH v9 3/5] arm64: dts: mt7986: add mmc related device nodes
Date: Fri,  6 Jan 2023 16:28:43 +0100	[thread overview]
Message-ID: <20230106152845.88717-4-linux@fw-web.de> (raw)
In-Reply-To: <20230106152845.88717-1-linux@fw-web.de>

From: Sam Shih <sam.shih@mediatek.com>

This patch adds mmc support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
v2:
- update mmc-node because clocks changed

v3:
- fix pullups/pulldowns for mt7986a-rfb to have generic bias-pull-*

v6:
- add 3v3 regulator in mt7986a-rfb (was in usb patch before)
- dropped AngeloGioacchino RB because of this change
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 96 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 15 +++
 2 files changed, 111 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 58089fcf4d16..c7a2ac764a30 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -5,6 +5,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/pinctrl/mt65xx.h>
+
 #include "mt7986a.dtsi"
 
 / {
@@ -23,6 +25,24 @@ memory@40000000 {
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &crypto {
@@ -58,7 +78,83 @@ switch: switch@0 {
 	};
 };
 
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
 &pio {
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 9ff2968152ae..9c552442c02d 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -346,6 +346,21 @@ ssusb: usb@11200000 {
 			status = "disabled";
 		};
 
+		mmc0: mmc@11230000 {
+			compatible = "mediatek,mt7986-mmc";
+			reg = <0 0x11230000 0 0x1000>,
+			      <0 0x11c20000 0 0x1000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&topckgen CLK_TOP_EMMC_416M_SEL>,
+				 <&infracfg CLK_INFRA_MSDC_HCK_CK>,
+				 <&infracfg CLK_INFRA_MSDC_CK>,
+				 <&infracfg CLK_INFRA_MSDC_133M_CK>,
+				 <&infracfg CLK_INFRA_MSDC_66M_CK>;
+			clock-names = "source", "hclk", "source_cg", "bus_clk",
+				      "sys_cg";
+			status = "disabled";
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1


  parent reply	other threads:[~2023-01-06 15:29 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-01-06 15:28 [PATCH v9 0/5] Add BananaPi R3 Frank Wunderlich
2023-01-06 15:28 ` [PATCH v9 1/5] dt-bindings: phy: mediatek,tphy: add support for mt7986 Frank Wunderlich
2023-01-12 17:41   ` Vinod Koul
2023-01-06 15:28 ` [PATCH v9 2/5] arm64: dts: mt7986: add usb related device nodes Frank Wunderlich
2023-01-06 15:28 ` Frank Wunderlich [this message]
2023-01-06 15:28 ` [PATCH v9 4/5] arm64: dts: mt7986: add pcie " Frank Wunderlich
2023-01-06 15:28 ` [PATCH v9 5/5] arm64: dts: mt7986: add Bananapi R3 Frank Wunderlich
2023-01-13 13:13 ` [PATCH v9 0/5] Add BananaPi R3 Matthias Brugger

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230106152845.88717-4-linux@fw-web.de \
    --to=linux@fw-web.de \
    --cc=chunfeng.yun@mediatek.com \
    --cc=devicetree@vger.kernel.org \
    --cc=frank-w@public-files.de \
    --cc=kishon@kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mediatek@lists.infradead.org \
    --cc=linux-phy@lists.infradead.org \
    --cc=matthias.bgg@gmail.com \
    --cc=robh+dt@kernel.org \
    --cc=sam.shih@mediatek.com \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).