From: Conor Dooley <conor@kernel.org>
To: marius.cristea@microchip.com
Cc: jic23@kernel.org, lars@metafoo.de, robh+dt@kernel.org,
linux-iio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH 1/2] dt-bindings: iio: adc: adding MCP3564 ADC
Date: Fri, 19 May 2023 19:29:15 +0100 [thread overview]
Message-ID: <20230519-variably-direction-cfa9a034e844@spud> (raw)
In-Reply-To: <20230519160145.44208-2-marius.cristea@microchip.com>
[-- Attachment #1: Type: text/plain, Size: 1917 bytes --]
Hey Marius,
On Fri, May 19, 2023 at 07:01:44PM +0300, marius.cristea@microchip.com wrote:
> From: Marius Cristea <marius.cristea@microchip.com>
>
> This is the device tree schema for iio driver for
> Microchip family of 153.6 ksps, Low-Noise 16/24-Bit
> Delta-Sigma ADCs with an SPI interface.
Just one quick process bit, please try to CC all of the maintainers
listed by get_maintainer.pl - you unfortunately managed to miss 2 of the
3 dt-binding maintainers :/ Perhaps you ran get_maintainer.pl using our
vendor tree?
> Signed-off-by: Marius Cristea <marius.cristea@microchip.com>
> ---
> + vref-supply:
> + description:
> + Some devices have a specific reference voltage supplied on a different
> + pin to the other supplies. Needed to be able to establish channel scaling
> + unless there is also an internal reference available (e.g. mcp3564r)
Should this be marked as a required property for the non-r devices that
do not have an internal reference?
> + microchip,hw-device-address:
Hopefully Rob or Jonathan etc can chime in as to whether a common
property exists for this type of thing...
> + $ref: /schemas/types.yaml#/definitions/uint32
> + minimum: 0
> + maximum: 3
> + description:
> + The address is set on a per-device basis by fuses in the factory,
> + configured on request. If not requested, the fuses are set for 0x1.
> + The device address is part of the device markings to avoid
> + potential confusion. This address is coded on two bits, so four possible
> + addresses are available when multiple devices are present on the same
> + SPI bus with only one Chip Select line for all devices.
..although if it doesn't, it'd be good, I think, to add here where the
property crops up in spi transfers. And if not in the description, in
the commit message instead?
Thanks,
Conor.
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
next prev parent reply other threads:[~2023-05-19 18:29 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-05-19 16:01 [PATCH 0/2] Adding support for Microchip MCP3564 ADC family marius.cristea
2023-05-19 16:01 ` [PATCH 1/2] dt-bindings: iio: adc: adding MCP3564 ADC marius.cristea
2023-05-19 18:29 ` Conor Dooley [this message]
2023-05-20 15:17 ` Jonathan Cameron
2023-06-08 19:34 ` Rob Herring
2023-06-09 17:41 ` Jonathan Cameron
2023-05-20 13:20 ` Jonathan Cameron
2023-05-24 10:37 ` Mike Looijmans
2023-05-28 19:16 ` Jonathan Cameron
2023-05-19 16:01 ` [PATCH 2/2] iio: adc: adding support for " marius.cristea
2023-05-20 15:15 ` Jonathan Cameron
2023-06-22 11:32 ` Marius.Cristea
2023-07-02 10:28 ` Jonathan Cameron
2023-05-24 11:05 ` Mike Looijmans
2023-05-28 19:20 ` Jonathan Cameron
2023-06-20 14:34 ` Mike Looijmans
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230519-variably-direction-cfa9a034e844@spud \
--to=conor@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jic23@kernel.org \
--cc=lars@metafoo.de \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marius.cristea@microchip.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).