[PATCH v4 1/2] arm64: dts: allwinner: h616: Add Mango Pi MQ-Quad DTS

[Matthew Croughan <matthew.croughan@nix.how>]

Mango Pi MQ Quad is a H616 based SBC, add basic support for the board
and its peripherals

Signed-off-by: Matthew Croughan <matthew.croughan@nix.how>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun50i-h616-mangopi-mq-quad.dts | 183 ++++++++++++++++++
 2 files changed, 184 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-mangopi-mq-quad.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 6a96494a2e0a..06c5b97dbfc3 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -38,5 +38,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-mangopi-mq-quad.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-mangopi-mq-quad.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-mangopi-mq-quad.dts
new file mode 100644
index 000000000000..dc1b88e0adae
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-mangopi-mq-quad.dts
@@ -0,0 +1,183 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ * Copyright (C) 2020 Arm Ltd.
+ *
+ * Copyright (C) 2023 Matthew Croughan <matthew.croughan@nix.how>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "MangoPi MQ-Quad";
+	compatible = "widora,mangopi-mq-quad", "allwinner,sun50i-h616";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+		};
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the USB-C socket */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		/* board wide 3V3 supply directly from SY8008 regulator */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 18 GPIO_ACTIVE_LOW>; /* PG18 */
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pc-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc3v3>;
+	vcc-pi-supply = <&reg_vcc3v3>;
+};
+
+/* USB 2 & 3 are on headers only. */
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	rtl8723ds: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 15 IRQ_TYPE_LEVEL_LOW>; /* PG15 */
+		interrupt-names = "host-wake";
+	};
+};
+
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723ds-bt";
+		device-wake-gpios = <&pio 6 17 GPIO_ACTIVE_HIGH>; /* PG17 */
+		enable-gpios = <&pio 6 19 GPIO_ACTIVE_HIGH>; /* PG19 */
+		host-wake-gpios = <&pio 6 16 GPIO_ACTIVE_HIGH>; /* PG16 */
+	};
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&r_i2c {
+	status = "okay";
+
+	axp313a: pmic@36 {
+		compatible = "x-powers,axp313a";
+		reg = <0x36>;
+    /* ALDO1 is feeding both VCC-PLL and VCC-DCXO, always-on is required,
+     * as removing power would cut the 1.8v supply for the RAM */
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-1v8";
+			};
+
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <990000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdc2: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-name = "vdd-dram";
+			};
+
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+&usbotg {
+	/*
+	 * PHY0 pins are connected to a USB-C socket, but a role switch
+	 * is not implemented: both CC pins are pulled to GND.
+	 * The VBUS pins power the device, so a fixed peripheral mode
+	 * is the best choice.
+	 * The board can be powered via GPIOs, in this case port0 *can*
+	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
+	 * then provided by the GPIOs. Any user of this setup would
+	 * need to adjust the DT accordingly: dr_mode set to "host",
+	 * enabling OHCI0 and EHCI0.
+	 */
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc5v>;
+	status = "okay";
+};
-- 
2.41.0