From: Varshini Rajendran <varshini.rajendran@microchip.com>
To: <robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>,
<conor+dt@kernel.org>, <nicolas.ferre@microchip.com>,
<alexandre.belloni@bootlin.com>, <claudiu.beznea@tuxon.dev>,
<andre.przywara@arm.com>, <gregory.clement@bootlin.com>,
<linus.walleij@linaro.org>, <baruch@tkos.co.il>,
<varshini.rajendran@microchip.com>, <mihai.sain@microchip.com>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>
Subject: [PATCH v4 39/39] ARM: dts: at91: sam9x75_curiosity: add sam9x75 curiosity board
Date: Fri, 23 Feb 2024 23:01:13 +0530 [thread overview]
Message-ID: <20240223173113.673595-1-varshini.rajendran@microchip.com> (raw)
In-Reply-To: <20240223171342.669133-1-varshini.rajendran@microchip.com>
Add device tree file for sam9x75 curiosity board.
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
---
Changes in v4:
- Removed full node paths
- Renamed Leds with color names
- Corrected regulator node names
- Added support for classd and i2s nodes and their corresponding
pinctrl nodes
- Dropped USB nodes owing to the discussion here
https://lore.kernel.org/linux-devicetree/CAL_JsqJ9PrX6fj-EbffeJce09MXs=B7t+KS_kOinxaRx38=WxA@mail.gmail.com/
(Explained elaborately in the cover letter)
- Updated the linux,code property with the necessary value
---
arch/arm/boot/dts/microchip/Makefile | 3 +
.../dts/microchip/at91-sam9x75_curiosity.dts | 309 ++++++++++++++++++
2 files changed, 312 insertions(+)
create mode 100644 arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
diff --git a/arch/arm/boot/dts/microchip/Makefile b/arch/arm/boot/dts/microchip/Makefile
index efde9546c8f4..5b3d518da319 100644
--- a/arch/arm/boot/dts/microchip/Makefile
+++ b/arch/arm/boot/dts/microchip/Makefile
@@ -12,6 +12,7 @@ DTC_FLAGS_at91-sama5d3_eds := -@
DTC_FLAGS_at91-sama5d3_xplained := -@
DTC_FLAGS_at91-sama5d4_xplained := -@
DTC_FLAGS_at91-sama7g5ek := -@
+DTC_FLAGS_at91-sam9x75_curiosity := -@
dtb-$(CONFIG_SOC_AT91RM9200) += \
at91rm9200ek.dtb \
mpa1600.dtb
@@ -59,6 +60,8 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
dtb-$(CONFIG_SOC_SAM9X60) += \
at91-sam9x60_curiosity.dtb \
at91-sam9x60ek.dtb
+dtb-$(CONFIG_SOC_SAM9X7) += \
+ at91-sam9x75_curiosity.dtb
dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2-2.dtb \
at91-kizbox3-hs.dtb \
diff --git a/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
new file mode 100644
index 000000000000..be37022d3d05
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
@@ -0,0 +1,309 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sam9x75_curiosity.dts - Device Tree file for Microchip SAM9X75 Curiosity board
+ *
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Varshini Rajendran <varshini.rajendran@microchip.com>
+ */
+/dts-v1/;
+#include "sam9x7.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Microchip SAM9X75 Curiosity";
+ compatible = "microchip,sam9x75-curiosity", "microchip,sam9x7", "atmel,at91sam9";
+
+ aliases {
+ i2c0 = &i2c6;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+ button-user {
+ label = "USER";
+ gpios = <&pioC 9 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_0>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led_gpio_default>;
+
+ led-red {
+ label = "red";
+ gpios = <&pioC 19 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-green {
+ label = "green";
+ gpios = <&pioC 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-blue {
+ label = "blue";
+ gpios = <&pioC 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ memory@20000000 {
+ device_type = "memory";
+ reg = <0x20000000 0x10000000>;
+ };
+};
+
+&classd {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_classd>;
+ atmel,pwm-type = "diff";
+ atmel,non-overlap-time = <10>;
+ status = "okay";
+};
+
+&dbgu {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dbgu>;
+ status = "okay";
+};
+
+&dma0 {
+ status = "okay";
+};
+
+&flx6 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+ status = "okay";
+};
+
+&i2c6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx6_default>;
+ i2c-analog-filter;
+ i2c-digital-filter;
+ i2c-digital-filter-width-ns = <35>;
+ status = "okay";
+
+ pmic@5b {
+ compatible = "microchip,mcp16502";
+ reg = <0x5b>;
+
+ regulators {
+ vdd_3v3: VDD_IO {
+ regulator-name = "VDD_IO";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-mode = <4>;
+ };
+ };
+
+ vddioddr: VDD_DDR {
+ regulator-name = "VDD_DDR";
+ regulator-min-microvolt = <1283000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-mode = <4>;
+ };
+ };
+
+ vddcore: VDD_CORE {
+ regulator-name = "VDD_CORE";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1210000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-mode = <4>;
+ };
+ };
+
+ vddcpu: VDD_OTHER {
+ regulator-name = "VDD_OTHER";
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-ramp-delay = <3125>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-mode = <4>;
+ };
+ };
+
+ vldo1: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vldo2: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2s {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2s_default>;
+ #sound-dai-cells = <0>;
+ status = "disabled";
+};
+
+&main_xtal {
+ clock-frequency = <24000000>;
+};
+
+&pinctrl {
+
+ classd {
+ pinctrl_classd: classd {
+ atmel,pins =
+ <AT91_PIOA 18 AT91_PERIPH_C AT91_PINCTRL_PULL_UP
+ AT91_PIOA 19 AT91_PERIPH_C AT91_PINCTRL_PULL_DOWN>;
+ };
+ };
+
+ dbgu {
+ pinctrl_dbgu: dbgu-0 {
+ atmel,pins = <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ flexcom {
+ pinctrl_flx6_default: flx6-twi {
+ atmel,pins =
+ <AT91_PIOA 24 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+ };
+ };
+
+ gpio-keys {
+ pinctrl_key_gpio_default: key-gpio-default {
+ atmel,pins = <AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ i2s {
+ pinctrl_i2s_default: i2s {
+ atmel,pins =
+ <AT91_PIOB 26 AT91_PERIPH_D AT91_PINCTRL_NONE /* I2SCK */
+ AT91_PIOB 15 AT91_PERIPH_D AT91_PINCTRL_NONE /* I2SWS */
+ AT91_PIOB 16 AT91_PERIPH_D AT91_PINCTRL_NONE /* I2SDIN */
+ AT91_PIOB 17 AT91_PERIPH_D AT91_PINCTRL_NONE /* I2SDOUT */
+ AT91_PIOB 25 AT91_PERIPH_D AT91_PINCTRL_NONE>; /* I2SMCK */
+ };
+ };
+
+ leds {
+ pinctrl_led_gpio_default: led-gpio-default {
+ atmel,pins = <AT91_PIOC 19 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOC 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOC 20 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ sdmmc0 {
+ pinctrl_sdmmc0_default: sdmmc0 {
+ atmel,pins =
+ <AT91_PIOA 2 AT91_PERIPH_A (AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_DIS) /* PA2 CK periph A with pullup */
+ AT91_PIOA 1 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_DIS) /* PA1 CMD periph A with pullup */
+ AT91_PIOA 0 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_DIS) /* PA0 DAT0 periph A */
+ AT91_PIOA 3 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_DIS) /* PA3 DAT1 periph A with pullup */
+ AT91_PIOA 4 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_DIS) /* PA4 DAT2 periph A with pullup */
+ AT91_PIOA 5 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_DIS)>; /* PA5 DAT3 periph A with pullup */
+ };
+ };
+
+}; /* pinctrl */
+
+&rtt {
+ atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ cd-gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ status = "okay";
+};
+
+&slow_xtal {
+ clock-frequency = <32768>;
+};
+
+&power_management {
+ debounce-delay-us = <976>;
+ status = "okay";
+
+ input@0 {
+ reg = <0>;
+ };
+};
+
+&trng {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
--
2.25.1
next prev parent reply other threads:[~2024-02-23 17:31 UTC|newest]
Thread overview: 92+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-02-23 17:13 [PATCH v4 00/39] Add support for sam9x7 SoC family Varshini Rajendran
2024-02-23 17:22 ` [PATCH v4 01/39] dt-bindings: net: cdns,macb: add sam9x7 ethernet interface Varshini Rajendran
2024-02-23 17:22 ` [PATCH v4 02/39] dt-bindings: atmel-sysreg: add sam9x7 Varshini Rajendran
2024-02-23 17:23 ` [PATCH v4 03/39] dt-bindings: crypto: add sam9x7 in Atmel AES Varshini Rajendran
2024-02-26 9:18 ` Tudor Ambarus
2024-02-23 17:23 ` [PATCH v4 04/39] dt-bindings: crypto: add sam9x7 in Atmel SHA Varshini Rajendran
2024-02-26 9:23 ` Tudor Ambarus
2024-02-23 17:24 ` [PATCH v4 05/39] dt-bindings: crypto: add sam9x7 in Atmel TDES Varshini Rajendran
2024-02-24 19:50 ` Conor Dooley
2024-02-26 9:24 ` Tudor Ambarus
2024-02-23 17:24 ` [PATCH v4 06/39] dt-bindings: i2c: at91: Add sam9x7 compatible string Varshini Rajendran
2024-02-24 19:49 ` Conor Dooley
2024-02-23 17:25 ` [PATCH v4 07/39] dt-bindings: atmel-ssc: add microchip,sam9x7-ssc Varshini Rajendran
2024-02-23 17:25 ` [PATCH v4 08/39] dt-bindings: atmel-nand: add microchip,sam9x7-pmecc Varshini Rajendran
2024-02-24 19:50 ` Conor Dooley
2024-02-26 10:43 ` Miquel Raynal
2024-02-23 17:25 ` [PATCH v4 09/39] dt-bindings: pinctrl: at91: add sam9x7 Varshini Rajendran
2024-02-29 13:41 ` Linus Walleij
2024-02-23 17:25 ` [PATCH v4 10/39] dt-bindings: rng: atmel,at91-trng: add sam9x7 TRNG Varshini Rajendran
2024-02-23 17:25 ` [PATCH v4 11/39] dt-bindings: rtt: at91rm9260: add sam9x7 compatible Varshini Rajendran
2024-02-24 19:51 ` Conor Dooley
2024-02-29 21:27 ` (subset) " Alexandre Belloni
2024-02-23 17:25 ` [PATCH v4 12/39] dt-bindings: serial: atmel,at91-usart: add compatible for sam9x7 Varshini Rajendran
2024-02-24 20:02 ` Conor Dooley
2024-02-28 7:03 ` Varshini.Rajendran
2024-02-28 11:49 ` Conor Dooley
2024-02-29 8:55 ` Varshini.Rajendran
2024-02-29 18:26 ` Conor Dooley
2024-02-23 17:26 ` [PATCH v4 13/39] ASoC: dt-bindings: atmel-classd: add sam9x7 compatible Varshini Rajendran
2024-02-24 19:48 ` Conor Dooley
2024-02-23 17:26 ` [PATCH v4 14/39] dt-bindings: pwm: at91: Add sam9x7 compatible strings list Varshini Rajendran
2024-02-24 20:03 ` Conor Dooley
[not found] ` <igmm3npqcnjuhhncfd22pjhjuzbtsl25jfzbpcsyx5bu2xbbto@ynp7psnpldxr>
2024-03-18 8:55 ` Uwe Kleine-König
2024-02-23 17:26 ` [PATCH v4 15/39] dt-bindings: watchdog: sama5d4-wdt: add compatible for sam9x7-wdt Varshini Rajendran
2024-02-24 20:04 ` Conor Dooley
2024-02-23 17:26 ` [PATCH v4 16/39] spi: dt-bindings: atmel,at91rm9200-spi: remove 9x60 compatible from list Varshini Rajendran
2024-02-26 9:09 ` Tudor Ambarus
2024-02-28 9:28 ` Varshini.Rajendran
2024-02-28 9:38 ` Tudor Ambarus
2024-02-23 17:26 ` [PATCH v4 17/39] ASoC: dt-bindings: microchip: add sam9x7 Varshini Rajendran
2024-02-23 17:27 ` [PATCH v4 18/39] ARM: at91: pm: add support for sam9x7 SoC family Varshini Rajendran
2024-03-03 12:20 ` claudiu beznea
2024-02-23 17:27 ` [PATCH v4 19/39] ARM: at91: pm: add sam9x7 SoC init config Varshini Rajendran
2024-03-03 12:20 ` claudiu beznea
2024-02-23 17:27 ` [PATCH v4 20/39] ARM: at91: add support in SoC driver for new sam9x7 Varshini Rajendran
2024-02-26 17:01 ` Nicolas Ferre
2024-03-03 12:21 ` claudiu beznea
2024-02-23 17:27 ` [PATCH v4 21/39] dt-bindings: clk: at91: add sam9x7 Varshini Rajendran
2024-02-24 20:05 ` Conor Dooley
2024-03-11 5:32 ` claudiu beznea
2024-02-23 17:27 ` [PATCH v4 22/39] dt-bindings: clk: at91: add sam9x7 clock controller Varshini Rajendran
2024-02-24 20:06 ` Conor Dooley
2024-03-11 5:33 ` claudiu beznea
2024-02-23 17:27 ` [PATCH v4 23/39] clk: at91: clk-sam9x60-pll: re-factor to support individual core freq outputs Varshini Rajendran
2024-02-23 17:27 ` [PATCH v4 24/39] clk: at91: sam9x7: add support for HW PLL freq dividers Varshini Rajendran
2024-03-11 5:34 ` claudiu beznea
2024-02-23 17:28 ` [PATCH v4 25/39] clk: at91: sama7g5: move mux table macros to header file Varshini Rajendran
2024-02-23 17:28 ` [PATCH v4 26/39] dt-bindings: clock: at91: Allow PLLs to be exported and referenced in DT Varshini Rajendran
2024-03-01 21:26 ` Rob Herring
2024-02-23 17:28 ` [PATCH v4 27/39] clk: at91: sam9x7: add sam9x7 pmc driver Varshini Rajendran
2024-03-11 5:58 ` claudiu beznea
2024-03-18 9:25 ` Varshini.Rajendran
2024-03-18 20:17 ` claudiu beznea
2024-02-23 17:28 ` [PATCH v4 28/39] dt-bindings: irqchip/atmel-aic5: Add support for sam9x7 aic Varshini Rajendran
2024-02-23 17:29 ` [PATCH v4 29/39] irqchip/atmel-aic5: Add support to get nirqs from DT for sam9x60 & sam9x7 Varshini Rajendran
2024-03-03 12:21 ` claudiu beznea
2024-03-08 8:50 ` Varshini.Rajendran
2024-03-08 10:15 ` Conor Dooley
2024-03-09 13:13 ` claudiu beznea
2024-02-23 17:29 ` [PATCH v4 30/39] power: reset: at91-poweroff: lookup for proper pmc dt node for sam9x7 Varshini Rajendran
2024-03-03 12:22 ` claudiu beznea
2024-02-23 17:29 ` [PATCH v4 31/39] power: reset: at91-reset: add reset support for sam9x7 SoC Varshini Rajendran
2024-02-23 17:30 ` [PATCH v4 32/39] power: reset: at91-reset: add sdhwc " Varshini Rajendran
2024-02-23 17:30 ` [PATCH v4 33/39] dt-bindings: reset: atmel,at91sam9260-reset: add sam9x7 Varshini Rajendran
2024-02-23 17:30 ` [PATCH v4 34/39] dt-bindings: power: reset: atmel,sama5d2-shdwc: " Varshini Rajendran
2024-02-23 17:30 ` [PATCH v4 35/39] ARM: at91: Kconfig: add config flag for SAM9X7 SoC Varshini Rajendran
2024-03-03 12:22 ` claudiu beznea
2024-02-23 17:30 ` [PATCH v4 36/39] ARM: configs: at91: enable config flags for sam9x7 SoC family Varshini Rajendran
2024-02-23 17:30 ` [PATCH v4 37/39] ARM: dts: at91: sam9x7: add device tree for SoC Varshini Rajendran
2024-03-03 12:24 ` claudiu beznea
2024-03-04 16:33 ` Varshini.Rajendran
2024-03-06 8:38 ` claudiu beznea
2024-02-23 17:31 ` [PATCH v4 38/39] dt-bindings: arm: add sam9x75 curiosity board Varshini Rajendran
2024-03-01 21:26 ` Rob Herring
2024-02-23 17:31 ` Varshini Rajendran [this message]
2024-03-03 12:19 ` [PATCH v4 39/39] ARM: dts: at91: sam9x75_curiosity: " claudiu beznea
2024-03-08 9:48 ` Varshini.Rajendran
2024-02-24 1:18 ` (subset) [PATCH v4 00/39] Add support for sam9x7 SoC family Mark Brown
2024-02-27 1:21 ` Andi Shyti
2024-02-27 3:20 ` patchwork-bot+netdevbpf
2024-02-28 15:53 ` (subset) " Mark Brown
2024-03-01 10:51 ` Herbert Xu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240223173113.673595-1-varshini.rajendran@microchip.com \
--to=varshini.rajendran@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=andre.przywara@arm.com \
--cc=baruch@tkos.co.il \
--cc=claudiu.beznea@tuxon.dev \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=gregory.clement@bootlin.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mihai.sain@microchip.com \
--cc=nicolas.ferre@microchip.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).