From: Alex Bee <knaerzche@gmail.com>
To: Lee Jones <lee@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Heiko Stuebner <heiko@sntech.de>,
Linus Walleij <linus.walleij@linaro.org>,
Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>
Cc: Chris Zhong <zyw@rock-chips.com>,
Zhang Qing <zhangqing@rock-chips.com>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org,
linux-gpio@vger.kernel.org, Alex Bee <knaerzche@gmail.com>
Subject: [PATCH 0/5] Add RK816 PMIC support
Date: Thu, 21 Mar 2024 15:39:07 +0100 [thread overview]
Message-ID: <20240321143911.90210-2-knaerzche@gmail.com> (raw)
This series aims to add support for Rockchip RK816 PMIC series. As per
datasheet it's targeted for RK3126/RK3128 (RK816-1), RK1108 (RK816-2) and
PX3-SE (RK816-3) but might be used for other SoCs as well. The mfd consists
of an integrated RTC, a GPIO controller, two 32k clock outputs, a power key
(output), 4 buck- and 5 ldo regulators, 3 regulator-switches, and charger
with integrated fuel gauge. Charger and fuel gauge are not part of this
series. Two of the switches (otg/boost) are part of the binding, but not of
the driver. They must only ever by enabled if no battery charging is
happening, but it will be enabled automatically if a battery is attached.
Thus they need some incorporation of a yet to be added charger driver.
Integration in the existing rk8xx-infrastructure was pretty straightforward
and only needed very little tweaking. In order to not further bloat the
driver(s) too much with additional definitions I tried to re-use existing
ones wherever possible.
The patches are loosely based on the vendor's implementation, verified
against the datasheet and tested/measured on RK3126 board. As they are
touching several subsystems I'm sending them (very) early for the
6.10-cycle.
Alex Bee (5):
dt-bindings: mfd: Add rk816 binding
mfd: rk8xx: Add RK816 support
pinctrl: rk805: Add rk816 pinctrl support
regulator: rk808: Support apply_bit for
rk808_set_suspend_voltage_range
regulator: rk808: Add RK816 support
.../bindings/mfd/rockchip,rk816.yaml | 259 ++++++++++++++++++
drivers/mfd/Kconfig | 4 +-
drivers/mfd/rk8xx-core.c | 103 +++++++
drivers/mfd/rk8xx-i2c.c | 45 ++-
drivers/pinctrl/pinctrl-rk805.c | 68 +++++
drivers/regulator/rk808-regulator.c | 218 ++++++++++++++-
include/linux/mfd/rk808.h | 141 ++++++++++
7 files changed, 831 insertions(+), 7 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml
--
2.43.2
next reply other threads:[~2024-03-21 14:39 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-03-21 14:39 Alex Bee [this message]
2024-03-21 14:39 ` [PATCH 1/5] dt-bindings: mfd: Add rk816 binding Alex Bee
2024-03-22 7:07 ` Krzysztof Kozlowski
2024-03-21 14:39 ` [PATCH 2/5] mfd: rk8xx: Add RK816 support Alex Bee
2024-03-22 17:58 ` kernel test robot
2024-03-22 21:45 ` kernel test robot
2024-03-23 7:01 ` kernel test robot
2024-03-21 14:39 ` [PATCH 3/5] pinctrl: rk805: Add rk816 pinctrl support Alex Bee
2024-03-21 14:39 ` [PATCH 4/5] regulator: rk808: Support apply_bit for rk808_set_suspend_voltage_range Alex Bee
2024-03-21 14:39 ` [PATCH 5/5] regulator: rk808: Add RK816 support Alex Bee
2024-03-21 15:01 ` [PATCH 0/5] Add RK816 PMIC support Dragan Simic
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240321143911.90210-2-knaerzche@gmail.com \
--to=knaerzche@gmail.com \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=heiko@sntech.de \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=lee@kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=robh@kernel.org \
--cc=zhangqing@rock-chips.com \
--cc=zyw@rock-chips.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).