Re: [PATCH] arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC

[Heiko Stuebner <heiko@sntech.de>]

Hi Andy,

Am Samstag, 3. August 2019, 13:46:12 CEST schrieb Andy Yan:
> Leez P710 is a RK3399 based SBC, designed by Leez team
> from lenovo [0].
> 
> Specification
> - Rockchip RK3399
> - 4/2GB LPDDR4
> - TF sd scard slot
> - eMMC
> - M.2 B-Key for 4G LTE
> - AP6256 for WiFi + BT
> - Gigabit ethernet
> - HDMI out
> - 40 pin header
> - TYPE-C Power supply
> 
> [0] https://leez.lenovo.com
> 
> Signed-off-by: Andy Yan <andyshrk@gmail.com>
> ---
>  .../devicetree/bindings/arm/rockchip.yaml     |   5 +
>  arch/arm64/boot/dts/rockchip/Makefile         |   1 +
>  .../boot/dts/rockchip/rk3399-leez-p710.dts    | 635 ++++++++++++++++++
>  3 files changed, 641 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
> index 34865042f4e4..da9cd947abfa 100644
> --- a/Documentation/devicetree/bindings/arm/rockchip.yaml
> +++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
> @@ -329,6 +329,11 @@ properties:
>                - khadas,edge-v
>            - const: rockchip,rk3399
>  
> +      - description: Leez RK3399 P710
> +        items:
> +          - const: leez,p710

Is "leez" really the vendor?
Part of me would assume something like
	lenovo,leez-p710

So please clarify :-)
And also please make sure the decided vendor is part of the vendor-prefixes
binding in Documentation/devicestree/bindings/vendor-prefixes.yaml

> +          - const: rockchip,rk3399
> +
>        - description: mqmaker MiQi
>          items:
>            - const: mqmaker,miqi
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index daa2c78e22c3..1f18a9392d15 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-hugsun-x99.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-khadas-edge.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-khadas-edge-captain.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-khadas-edge-v.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-leez-p710.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4.dtb
>  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts b/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts
> new file mode 100644
> index 000000000000..b342f5e8692b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts
> @@ -0,0 +1,635 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 Andy Yan <andy.yan@gmail.com>
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/pwm/pwm.h>
> +#include "rk3399.dtsi"
> +#include "rk3399-opp.dtsi"
> +
> +/ {
> +	model = "Leez RK3399 P710";
> +	compatible = "leez,p710", "rockchip,rk3399";

same comment as above, so maybe:
	model = "Lenovo Leez RK3399 P710";
	compatible = "lenovo,leez-p710", "rockchip,rk3399";



> +
> +	chosen {
> +		stdout-path = "serial2:1500000n8";
> +	};
> +
> +	clkin_gmac: external-gmac-clock {
> +		compatible = "fixed-clock";
> +		clock-frequency = <125000000>;
> +		clock-output-names = "clkin_gmac";
> +		#clock-cells = <0>;
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		clocks = <&rk808 1>;
> +		clock-names = "ext_clock";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&wifi_enable_h>;
> +		reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	dc5v_adp: dc-5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "dc5v_adapter";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	vcc5v0_sys: vcc-sys {

vcc5v0_sys: vcc5v0-sys ?

> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&dc5v_adp>;
> +	};
> +
> +	vcc3v3_sys: vcc3v3-sys {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc3v3_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +
> +	vcc5v0_host: vcc5v0-host-regulator {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpio = <&gpio2 RK_PA2 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vcc5v0_host_en>;
> +		regulator-name = "vcc5v0_host";
> +		regulator-always-on;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +
> +	vcc_lan: vcc3v3-phy-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_lan";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};

In general, please model an actual regulator-tree and do not copy the
unspecific Rockchip vendor tree. These unconnected regulators are a very
good indicator that the real power-tree got ignored (missing vin-supply here)

I found schematics on https://github.com/leezsbc/resources/wiki/Leez-P710:
链接: https://pan.baidu.com/s/1NPWbuI5csT4zftKUCnRs7g
提取码: rvrh

and there the power-tree is described in a complete way.

regulator/regulator_summaray in the kernels debugfs should
show a nice tree structure starting from the dc-adapter input.

Also please use names matching the supply names from the schematics.

Same for pinctrl names, please use names as used in the board schematics.


> +	vdd_log: vdd-log {
> +		compatible = "pwm-regulator";
> +		pwms = <&pwm2 0 25000 1>;
> +		regulator-name = "vdd_log";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <800000>;
> +		regulator-max-microvolt = <1400000>;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +};
> +
> +&cpu_l0 {
> +	cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l1 {
> +	cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l2 {
> +	cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l3 {
> +	cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_b0 {
> +	cpu-supply = <&vdd_cpu_b>;
> +};
> +
> +&cpu_b1 {
> +	cpu-supply = <&vdd_cpu_b>;
> +};
> +
> +&emmc_phy {
> +	status = "okay";
> +};
> +
> +&gmac {
> +	assigned-clocks = <&cru SCLK_RMII_SRC>;
> +	assigned-clock-parents = <&clkin_gmac>;
> +	clock_in_out = "input";
> +	phy-supply = <&vcc_lan>;
> +	phy-mode = "rgmii";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&rgmii_pins>;
> +	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
> +	snps,reset-active-low;
> +	snps,reset-delays-us = <0 10000 50000>;
> +	tx_delay = <0x28>;
> +	rx_delay = <0x11>;
> +	status = "okay";
> +};
> +
> +&gpu {
> +	mali-supply = <&vdd_gpu>;
> +	status = "okay";
> +};
> +
> +&hdmi {
> +	ddc-i2c-bus = <&i2c3>;

can this also use the internal i2c inside the dw-hdmi?


> +	pinctrl-names = "default";
> +	pinctrl-0 = <&hdmi_cec>;
> +	status = "okay";
> +};
> +
> +&hdmi_sound {
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	clock-frequency = <400000>;
> +	i2c-scl-rising-time-ns = <168>;
> +	i2c-scl-falling-time-ns = <4>;
> +	status = "okay";
> +
> +	rk808: pmic@1b {
> +		compatible = "rockchip,rk808";
> +		reg = <0x1b>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
> +		#clock-cells = <1>;
> +		clock-output-names = "xin32k", "rk808-clkout2";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pmic_int_l>;
> +		rockchip,system-power-controller;
> +		wakeup-source;
> +
> +		vcc1-supply = <&vcc5v0_sys>;
> +		vcc2-supply = <&vcc5v0_sys>;
> +		vcc3-supply = <&vcc5v0_sys>;
> +		vcc4-supply = <&vcc5v0_sys>;
> +		vcc6-supply = <&vcc5v0_sys>;
> +		vcc7-supply = <&vcc5v0_sys>;
> +		vcc8-supply = <&vcc3v3_sys>;
> +		vcc9-supply = <&vcc5v0_sys>;
> +		vcc10-supply = <&vcc5v0_sys>;
> +		vcc11-supply = <&vcc5v0_sys>;
> +		vcc12-supply = <&vcc3v3_sys>;
> +		vddio-supply = <&vcc_1v8>;
> +
> +		regulators {
> +			vdd_center: DCDC_REG1 {
> +				regulator-name = "vdd_center";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <750000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-ramp-delay = <6001>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdd_cpu_l: DCDC_REG2 {
> +				regulator-name = "vdd_cpu_l";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <750000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-ramp-delay = <6001>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_ddr: DCDC_REG3 {
> +				regulator-name = "vcc_ddr";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +				};
> +			};
> +
> +			vcc_1v8: DCDC_REG4 {
> +				regulator-name = "vcc_1v8";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vcc1v8_dvp: LDO_REG1 {
> +				regulator-name = "vcc1v8_dvp";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc1v8_hdmi: LDO_REG2 {
> +				regulator-name = "vcc1v8_hdmi";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcca_1v8: LDO_REG3 {
> +				regulator-name = "vcca_1v8";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vccio_sd: LDO_REG4 {
> +				regulator-name = "vccio_sd";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <3000000>;
> +				};
> +			};
> +
> +			vcca3v0_codec: LDO_REG5 {
> +				regulator-name = "vcca3v0_codec";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_1v5: LDO_REG6 {
> +				regulator-name = "vcc_1v5";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1500000>;
> +				regulator-max-microvolt = <1500000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1500000>;
> +				};
> +			};
> +
> +			vcc0v9_hdmi: LDO_REG7 {
> +				regulator-name = "vcc0v9_hdmi";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <900000>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_3v0: LDO_REG8 {
> +				regulator-name = "vcc_3v0";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <3000000>;
> +				};
> +			};
> +

unneeded blank line

> +		};
> +	};
> +


Heiko