From: Aswath Govindraju <a-govindraju@ti.com>
To: unlisted-recipients:; (no To-header on input)
Cc: Vignesh Raghavendra <vigneshr@ti.com>,
Lokesh Vutla <lokeshvutla@ti.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Jan Kiszka <jan.kiszka@siemens.com>, Nishanth Menon <nm@ti.com>,
Tero Kristo <kristo@kernel.org>, Rob Herring <robh+dt@kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v2] arm64: dts: ti: k3-am65: Add support for UHS-I modes in MMCSD1 subsystem
Date: Tue, 11 May 2021 15:25:33 +0530 [thread overview]
Message-ID: <238b6d95-ae9d-2a9c-ae8c-97dcc712ee83@ti.com> (raw)
In-Reply-To: <20210511095339.16268-1-a-govindraju@ti.com>
On 11/05/21 3:23 pm, Aswath Govindraju wrote:
> UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1].
>
> Add support by removing the no-1-8-v tag and including the voltage
> regulator device tree nodes for power cycling.
>
> However, the 4 bit interface of AM65 SR 1.0 cannot be supported at 3.3 V or
> 1.8 V because of erratas i2025 and i2026 [2]. As the SD card is the primary
> boot mode for development usecases, continue to enable SD card and disable
> UHS-I modes in it to minimize any ageing issues happening because of
> erratas.
>
> k3-am6528-iot2050-basic and k3-am6548-iot2050-advanced boards use S.R. 1.0
> version of AM65 SoC. Therefore, add no-1-8-v in sdhci1 device tree nodes
> for these boards.
>
> [1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1
> [2] - https://www.ti.com/lit/er/sprz452e/sprz452e.pdf
>
> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
> ---
changes since v1:
- added no-1-8-v tag in sdhci1 dt nodes of k3-am6528-iot2050-basic and
k3-am6548-iot2050-advanced boards as they use S.R.1.0 version AM65 SoC.
Thanks,
Aswath
> arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 1 -
> .../boot/dts/ti/k3-am6528-iot2050-basic.dts | 4 +++
> .../arm64/boot/dts/ti/k3-am654-base-board.dts | 33 +++++++++++++++++++
> .../dts/ti/k3-am6548-iot2050-advanced.dts | 4 +++
> 4 files changed, 41 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index cb340d1b401f..632f32fce4a1 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -301,7 +301,6 @@
> ti,otap-del-sel = <0x2>;
> ti,trm-icp = <0x8>;
> dma-coherent;
> - no-1-8-v;
> };
>
> scm_conf: scm-conf@100000 {
> diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
> index 4f7e3f2a6265..485266960d5f 100644
> --- a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
> @@ -40,6 +40,10 @@
> status = "disabled";
> };
>
> +&sdhci1 {
> + no-1-8-v;
> +};
> +
> &main_pmx0 {
> main_uart0_pins_default: main-uart0-pins-default {
> pinctrl-single,pins = <
> diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> index 9e87fb313a54..51c594b4dddb 100644
> --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> @@ -91,6 +91,38 @@
> #clock-cells = <0>;
> clock-frequency = <24000000>;
> };
> +
> + evm_12v0: fixedregulator-evm12v0 {
> + /* main supply */
> + compatible = "regulator-fixed";
> + regulator-name = "evm_12v0";
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vcc3v3_io: fixedregulator-vcc3v3io {
> + /* Output of TPS54334 */
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&evm_12v0>;
> + };
> +
> + vdd_mmc1_sd: fixedregulator-sd {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_mmc1_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + enable-active-high;
> + vin-supply = <&vcc3v3_io>;
> + gpio = <&pca9554 4 GPIO_ACTIVE_HIGH>;
> + };
> };
>
> &wkup_pmx0 {
> @@ -350,6 +382,7 @@
> * disable sdhci1
> */
> &sdhci1 {
> + vmmc-supply = <&vdd_mmc1_sd>;
> pinctrl-names = "default";
> pinctrl-0 = <&main_mmc1_pins_default>;
> ti,driver-strength-ohm = <50>;
> diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
> index ec9617c13cdb..3643a19b5f33 100644
> --- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
> @@ -55,6 +55,10 @@
> disable-wp;
> };
>
> +&sdhci1 {
> + no-1-8-v;
> +};
> +
> &main_uart0 {
> status = "disabled";
> };
>
next prev parent reply other threads:[~2021-05-11 9:55 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-11 9:53 [PATCH v2] arm64: dts: ti: k3-am65: Add support for UHS-I modes in MMCSD1 subsystem Aswath Govindraju
2021-05-11 9:55 ` Aswath Govindraju [this message]
2021-05-11 10:01 ` Jan Kiszka
2021-05-11 10:13 ` Aswath Govindraju
2021-05-11 15:26 ` Jan Kiszka
2021-05-11 16:33 ` Nishanth Menon
2021-05-11 16:40 ` Aswath Govindraju
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=238b6d95-ae9d-2a9c-ae8c-97dcc712ee83@ti.com \
--to=a-govindraju@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=jan.kiszka@siemens.com \
--cc=kishon@ti.com \
--cc=kristo@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=lokeshvutla@ti.com \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).